Radical-initiated homopolymerization and copolymerization of ethyl α-hydroxymethylacrylate

Ethyl α-hydroxymethylacrylate (EHMA) was synthesized and homopolymerized in bulk and in solution. The poly(EHMA) is readily soluble in alcohol, acetone, tetrahydrofuran, and methylene chloride at room temperature. Intramolecular lactone formation occurred when poly(EHMA) was heated to 180–230°C. The kinetics of EHMA homopolymerization was investigated in ethyl acetate, using α,α′-azobisisobutylonitrile as an initiator. The rate of polymerization R_p was expressed by R_p = k[AIBN]^0.50[EHMA]^1.4 and the overall activation energy was calculated as 71.9 kJ/mol. Kinetic constants for EHMA polymerization were obtained as follows: k_p/k = 0.17L^0.9mol^?0.9s^?0.5; 2fk_d = 1.5 × 10^?5 s^?1. The relative reactivity ratios of EHMA(M₂) copolymerization with styrene (r₁ = 0.472, r₂ = 0.564) in ethyl acetate were obtained. Applying the Q-e scheme led to Q = 0.84 and e = 0.35 for EHMA.     

Copolymerization of ethyl α-(hydroxymethyl)acrylate with maleimide and characterization of the resulting copolymer

Copolymerization of maleimide (MI) and ethyl α-(hydroxymethyl)acrylate (EHMA) was performed at 60°C with AIBN as the initiator in THF. The monomer reactivity ratios were determined as r₁ (MI) = 0.13 and r₂ (EHMA) = 2.20. As the molar fraction of MI in the monomer feed increased, the initial rate of copolymerization decreased. TGA diagrams suggested the crosslinking reaction of the copolymer on heating. DSC and WAXD results suggested the existence of incomplete crystallinity in the copolymer. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1291–1299, 1998     

Copolymers of 2-vinyl-4,4-dimethylazlactone with styrene and ethyl α-hydroxymethylacrylate

The monomer reactivity ratios for copolymerization of 2-vinyl-4,4-dimethylazlactone (VA) and ethyl α-hydroxymethylacrylate (EHMA) were 0.20–0.24 and 0.53–0.74, respectively, which show that EHMA is slightly more reactive with VA than with itself and should lead to random copolymers favoring alternation. The VA–styrene (VA–St) system also has a tendency to form random copolymers but with increased tendency for alternation with both r₁ and r₂ between 0.18–0.22. T_g's of VA–EHMA and VA–St copolymers varied between 100 and 136°C, and 96 and 117°C, respectively. Thermolysis of VA–EHMA copolymers resulted in crosslinking via the ring-opening reaction of VA groups by EHMA alcohols, followed by transesterification involving EHMA units at higher temperatures leading to highly crosslinked structures. The performed dimer of EHMA and VA was also synthesized and found to be an effective crosslinking agent in free radical vinyl polymerizations.     

Determination of the Microstructure of Some Methyl Methacrylate-Butadiene Copolymers by 220 MHz Proton Magnetic Resonance Spectroscopy

Abstract

Proton magnetic resonance (PMR) spectroscopy at 220 MHz has been used to gain information about the relative proportions of various methyl methacrylate centered triads and pentads in some methyl methacrylate (MMA)-butadiene (BU) copolymers prepared with a free-radical catalyst. The PMR peaks used are the MMA α-methyl peaks recorded using CDCL₃ as solvent, and the MMA α methyl peaks recorded using C₅D₅N as solvent. Measured triad and pentad fractions are in good agreement with those calculated from the reactivity ratios r₁ = 0.17 and r₂ = 0.60, where MMA = Monomer 1. Surprisingly, the α-methyl peaks provide information also about the ratio of cis-1,4- to trans-1, 4-butadiene units in the copolymer. Proportions of 1,2-butadiene units are obtained from the relative areas of peaks due to vinyl and vinylene protons.     

Radical-initiated homo- and copolymerization of α-methylene-γ-butyrolactone

The kinetics of α-methylene-γ-butyrolactone (α-MBL) homopolymerization was investigated in N,N-dimethylformamide (DMF) with azobis(isobutyronitrile) as initiator. The rate of polymerization (R_p) was expresed by R_p = k[AIBN]^0.54[α-MBL]^1.1 and the overall activation energy was calculated as 76.1 kJ/mol. Kinetic constants for α-MBL polymerization were obtained as follows: k_p/k_t^1/2 = 0.161 L^1/2 mol^?1/2·s^?1/2; 2fk_d = 2.18 × 10^?5 s^?1. The relative reactivity ratios of α-MBL(M₂) copolymerization with styrene (r₁ = 0.14, r₂ = 0.87) were obtained. Applying the Q–e scheme led to Q = 2.2 and e = 0.65. These Q and e values for α-MBL are higher than those for MMA     

Kinetic and ESR studies on radical polymerization of methyl methacrylate in the presence of fullerene

The effect of fullerene (C₆₀) on the radical polymerization of methyl methacrylate (MMA) in benzene was studied kinetically and by means of ESR, where dimethyl 2,2′-azobis(isobutyrate) (MAIB) was used as initiator. The polymerization rate (R_p) and the molecular weight of resulting poly(MMA) decreased with increasing C₆₀ concentration ((0–2.11) × 10⁻⁴ mol/L). The molecular weight of polymer tended to increase with time at higher C₆₀ concentrations. R_p at 50°C in the presence of C₆₀ (7.0 × 10⁻⁵ mol/L) was expressed by R_p = k[MAIB]^0.5[MMA]^1.25. The overall activation energy of polymerization at 7.0 × 10⁻⁵ mol/L of C₆₀ concentration was calculated to be 23.2 kcal/mol. Persistent fullerene radicals were observed by ESR in the polymerization system. The concentration of fullerene radicals was found to increase linearly with time and then be saturated. The rate of fullerene radical formation increased with MAIB concentration. Thermal polymerization of styrene (St) in the presence of resulting poly(MMA) seemed to yield a starlike copolymer carrying poly(MMA) and poly(St) arms. The results (r₁ = 0.53, r₂ = 0.56) of copolymerization of MMA and St with MAIB at 60°C in the presence of C₆₀ (7.15 × 10⁻⁵ mol/L) were similar to those (r₁ = 0.46, r₂ = 0.52) in the absence of C₆₀. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2905–2912, 1998     

Copolymerization of 2-Hydroxypropyl Methacrylate with Alkyl Met hacrylates

2-Hydroxypropyl methacrylate (2-HPMA) has been copolym-erized with ethyl methacrylate (EMA), n-butyl methacrylate (BMA), and 2-ethylhexyl methacrylate (EHMA) in bulk at 60°C using benzoyl peroxide as initiator. The copolymer composition has been determined from the hydroxyl content. The reactivity ratios have been calculated by the Yezrielev, Brokhina, and Raskin method. For copolymerization of 2-HPMA (M₁) with EMA (M₂), the reactivity ratios are r₁ = 1.807 ± 0.032 and r₂ = 0.245 ± 0.021; with BMA (M₂) they are n = 2.378 ± 0.001 and r₂ = 0.19 ± 0.01; and with EHMA the values are r₁ = 4.370 ± 0.048 and r₂ = 0.103 ± 0.006. Since reactivity ratios are the measure of distribution of monomer units in copolymer chain, the values obtained are compared and discussed. This enables us to choose a suitable copolymer for synthesizing thermoset acrylic polymers, which are obtained from cross-linking of hydroxy functional groups of HPMA units, for specific end-uses.     

Reactivity of methacrylates in anionic copolymerization with methyl methacrylate by n-BuLi

Monomer reactivity ratios, r₁ and r₂ were determined in the anionic copolymerizations of methyl methacrylate (MMA, M₁) with ethyl (EtMA), isopropyl (i-PrMA), tert-butyl (t-BuMA), benzyl (BzMA), α-methylbenzyl (MBMA), diphenylmethyl (DPMMA), α,α-dimethylbenzyl (DMBMA), and trityl (TrMA) methacrylates (M₂) by use of n-BuLi as an initiator in toluene and THF at -78°C. The order of the reactivity of the monomers towards MMA anion was DPMMA > BzMA > MMA > EtMA > MBMA > i-PrMA > t-BuMA > TrMA > DMBMA in toluene and TrMA > BzMA > MMA > DPMMA > EtMA > MBMA > i-PrMA > DMBMA > t-BuMA in THF. Except for the extremely low reactivity of TrMA and DPMMA in toluene due to steric hindrance, the order was explained in terms of the polar effect of the ester groups. A linear relationship was found between log (1/r₁) and Taft's σ* values of the ester groups, where the ρ* value was 1.1. The plots of log (1/r₁) vs. the ¹H_a (cis to the carbonyl) and ¹³C_ß chemical shifts of the monomers were also on straight lines. The polymer obtained in the copolymerization of MMA with TrMA in toluene by n-BuLi at -78°C was a mixture of poly-MMA and a copolymer, suggesting that there exist two kinds of growing centers.     

Polymerization of α-methyleneindane: A cyclic analog of α-methylstyrene

α-Methyleniedane (MI), a cyclic analog of α-methylstyrene which does not undergo radical homopolymerization under standard conditions, was synthesized and subjected to radical, cationic, and anionic polymerizations. MI undergoes radical polymerization with α,α′-azobis(isobutyronitrile) in contrast to α-methylstyrene, owing to its reduced steric hindrance, though the polymerization is slow even in bulk. Cationic and anionic polymerization of MI with BF₃OEt₂ and n-butyllithium, respectively, proceed rapidly. The thermal degradation behavior of the polymer depends on the polymerization conditions. The anionic and radical polymers are heteortactic-rich. Reactivity ratios in bulk radical copolymerization on MI (M₂) with methacrylate (MMA, M₁) were determined at 60°C (r₁ = 0.129 and r₂ = 1.07). In order to clarify the copolymerization mechanism, radical copolymerization of MI with MMA was investigated in bulk at temperatures ranging from 50 to 80°C. The Mayo–Lewis equation has been found to be inadequate to describe the result due to depolymerization of MI sequences above 70°C.     

Reactivity ratios and sequence structures of the copolymers prepared using photo‐induced copolymerization of MMA with MTMP

4‐Methacryloyl‐2,2,6,6‐tetramethyl‐piperidine (MTMP) was applied as reactive hindered amine piperidine. Photo‐induced copolymerization of methyl methacrylate (MMA, M₁) with MTMP (M₂) was carried out in benzene solution at ambient temperature. The reactivity ratios for these monomers were measured by running a series of reactions at various feed ratios of initial monomers, and the monomer incorporation into copolymer was determined using ¹H NMR. Reactivity ratios of the MMA/MTMP system were measured to be r₁ = 0.37 and r₂ = 1.14 from extended Kelen‐Tüdos method. The results show that monomer MTMP prefers homopolymerization to copolymerization in the system, whereas monomer MMA prefers copolymerization to homopolymerization. Sequence structures of the MMA/MTMP copolymers were characterized using ¹H NMR. The results show that the sequence structure for the main chain of the MMA/MTMP copolymers is mainly composed of a syndiotactic configuration, only with a little heterotactic configuration. Three kinds of the sequences of rr, rr′, and lr′ in the syndiotactic configuration are found. The sequence‐length distribution in the MMA/MTMP copolymers is also obtained. For f₁ = 0.2, the monomer unit of MMA is mostly separated by MTMP units, and for f₁ = 0.6, the alternating tendency prevails and a large number of mono‐sequences are formed; further up to f₁ = 0.8, the monomer unit of MTMP with the sequence of one unit is interspersed among the chain of MMA. Copyright © 2012 John Wiley & Sons, Ltd.     

Studies of methyl methacrylate–glycidyl methacrylate copolymers: Copolymerization to low molecular weights and modification by ring-opening reaction of epoxy side groups

The copolymerization of methyl methacrylate (MMA) with glycidyl methacrylate (GMA) at 60°C with 2,2′-azobisisobutyronitrile (AIBN) as radical initiator and in the presence of thiophenol (TP) as chain-transfer agent has been investigated. Monomer reactivity ratios for MMA and GMA are found to be r₁ (MMA) = 0.80 ± 0.015 and r₂ (GMA) = 0.70 ± 0.015, from which Q and e values are calculated to be 0.68 and ?0.36 for GMA. The initial rate of copolymerization R_p at 60°C with AIBN (0.02 mole/l.) and TP (0.1, 0.01 mole/l.) were found to increase nonlinearly with increasing GMA concentration in the monomer feed. Homopolymerizations of MMA and GMA monomers were studied in the presence and in the absence of thiophenol. The values of δ (= k_t^1/2/k_p) for MMA and GMA were determined to be 10.25 and 3.00 (mole-sec/l.)^1/2, respectively. Using the values r₁ (MMA), r₂ (GMA), δ₁ (MMA), δ₂ (GMA), and R_p, the cross-termination constants ? for MMA–GMA monomers were determined (average value ? = 0.42). The increase in R_p values with increasing GMA content has been attributed to the cross-termination of MMA–GMA radicals. The transfer constant of TP has also been determined for GMA and found to be 1.00. A MMA–GMA copolymer of low molecular weight, containing 2.01% of oxirane oxygen, was modified by opening of the oxirane ring of GMA by reaction with diethanolamine (DEA). The reaction was carried out at 70 ± 1°C, the copolymer content of epoxy groups and the amine being assumed to be in the molar ratio of 1:4. Addition of a hydrogen-bond acceptor like nitrobenzene decreases, while addition of a hydrogen-bond donor like phenol increases the rate of epoxy ring opening with DEA. This indicates that a hydrogen-bonded intermediate is involved in this reaction and that it weakens the epoxy ring and enhances the rate of its opening with DEA. From the studies of the conversion rates, existence of a “nonspecific” side reaction has been shown which involves the reaction of the terminal epoxy groups of the copolymer and the hydroxyl groups of DEA or formed in the reaction with DEA (involves a chain coupling). DEA can be trifunctional in this reaction. This has been further confirmed from the increase of number-average molecular weights M?_n of the copolymers resulting from this coupling and the nitrogen content in the copolymers after modification with DEA.     

Nitroxide‐mediated radical copolymerization of methyl methacrylate controlled with a minimal amount of 9‐(4‐vinylbenzyl)‐9H‐carbazole

The controlled nitroxide‐mediated homopolymerization of 9‐(4‐vinylbenzyl)‐9H‐carbazole (VBK) and the copolymerization of methyl methacrylate (MMA) with varying amounts of VBK were accomplished by using 10 mol % {tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino} nitroxide relative to 2‐({tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino}oxy)‐2‐methylpropionic acid (BlocBuilder?) in dimethylformamide at temperatures from 80 to 125 °C. As little as 1 mol % of VBK in the feed was required to obtain a controlled copolymerization of an MMA/VBK mixture, resulting in a linear increase in molecular weight versus conversion with a narrow molecular weight distribution (M_w /M_n ≈ 1.3). Preferential incorporation of VBK into the copolymer was indicated by the MMA/VBK reactivity ratios determined: r_VBK = 2.7 ± 1.5 and r_MMA = 0.24 ± 0.14. The copolymers were found significantly “living” by performing subsequent chain extensions with a fresh batch of VBK and by ³¹P NMR spectroscopy analysis. VBK was found to be an effective controlling comonomer for NMP of MMA, and such low levels of VBK comonomer ensured transparency in the final copolymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Bulk Free‐Radical Co‐ and Terpolymerization of n‐Butyl Acrylate/2‐Ethylhexyl Acrylate/Methyl Methacrylate

n‐Butyl acrylate (BA), 2‐ethylhexyl acrylate (EHA), and methyl methacrylate (MMA) are commonly used monomers in pressure‐sensitive adhesive formulations. The bulk free‐radical copolymerizations of BA/EHA, MMA/EHA, and BA/MMA are studied at 60 °C to demonstrate the use of copolymer reactivity ratios for the prediction of BA/MMA/EHA terpolymer composition. The reactivity ratios for BA/EHA and MMA/EHA copolymer systems are determined using low conversion experiments; BA/MMA reactivity ratios are already known from the literature. The reactivity ratio estimates for the BA/EHA system are r _BA = 0.994 and r _EHA = 1.621 and the estimates for MMA/EHA are r _MMA = 1.496 and r _EHA = 0.315. High conversion experiments are conducted to validate the reactivity ratios. The copolymer reactivity ratios are shown to predict terpolymer composition of high conversion BA/MMA/EHA experiments.     

Curcumin,A Novel Natural Photoinitiator for the Copolymerization of Styrene and Methylmethacrylate

Curcumin (Cur), a natural colorant found in the roots of the Turmeric plant, has been reported for the first time as photoinitiator for the copolymerization of styrene (Sty) and methylmethacrylate (MMA). The kinetic data, inhibiting effect of benzoquinone and ESR studies indicate that the polymerization proceeds via a free radical mechanism. The system follows ideal kinetics (R_p α[Cur]^0.5[Sty]^0.97[MMA]¹). The reactivity ratios calculated by using the Finemann–Ross and Kelen‐Tudos models were r₁(MMA)=0.46 and r₂(Sty)=0.52. IR and NMR analysis confirmed the structure of the copolymer. NMR spectrum showing methoxy protons as three distinct groups of resonance between 2.2–3.75 δ and phenyl protons of styrene at 6.8–7.1 δ confirmed the random nature of the copolymer. The mechanism for formation of radicals and random copolymer of styrene and MMA [Sty‐co‐MMA] is also discussed.     

Synthesis of degradable poly(methyl methacrylate) star polymers via RAFT copolymerization with cyclic ketene acetals

Copolymerization of the cyclic ketene acetal 5,6‐benzo‐2‐methylene‐1,3‐dioxepane (BMDO) with methyl methacrylate (MMA) is studied with respect to its copolymerization parameters and the suitability to control BMDO/MMA copolymerizations via the reversible addition‐fragmentation chain transfer (RAFT) technique to obtain linear and 4‐arm star polymers. BMDO shows disparate copolymerization behavior with MMA and r₁ = 0.33 ± 0.06 and r₂ = 6.0 ± 0.8 have been determined for polymerization at 110 °C in anisole from fitting copolymer composition vs. comonomer feed data to the Lewis–Mayo equation. Copolymerization of the two monomers is successful in RAFT polymerization employing a trithiocarbonate control agent. As desired, polymers contain only little amount of polyester units stemming from BMDO units and preliminary degradation experiment show that the polymer degrades slowly, but steadily in aqueous 1 M NaOH dispersion. Within ten days, the polymers are broken down to low molecular weight segments from an initial molecular weight of M_n = 6000 g mol^?1. Star (co)polymerization with an erythritol‐based tetra‐functional RAFT agent following the Z‐group approach proceeds efficiently and polymers with a number‐average molecular weight of 10,000 g mol^?1 are readily obtained that degrade in similar manner as the linear copolymer counterparts. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1633–1641     

SYNTHESIS AND CHARACTERIZATION OF 1-NAPHTHYLMETHYL METHACRYLATE-METHYL METHACRYLATE COPOLYMERS

A series of 1-naphthylmethyl methacrylate (NMMA)-methyl methacrylate (MMA) copolymerswere synthesized on free radical mechanism. The reactivity ratios of NMMA (r_1) and MMA (r_2) werereported to be 0.83 and 0.89, respectively. The characterization of the copolymers by using IR, NMR,GPC, UV and fiuorescence spectrometry was described in this paper.     

Copolymerization of 2-Hydtoxypropyl Methacrylate with Alkyl Methacrylates

2-Hydroxypropyl methacrylate (2 HPMA) has been copolym-erized with ethyl methacrylate (EMA), n-butyl methacrylate (BMA), and 2-ethylhexyl methacrylate (EHMA) in bulk at 60°C using benzoyl peroxide as initiator. The copolymer composition has been determined from the hydroxyl content. The reactivity ratios have been calculated by the YBR method. For copolymerization of 2-HPMA (M₁) with EMA (M₂), the reactivity ratios are: r₁=1.807 ± 0.032, r₂=0.245 ± 0.021; with BMA (M₂) they are r₁=2.378 ± 0.001, r₂=0.19 ± 0.01; and with EHMA the values are r₁=4.370 ± 0.048, r₂=0.103 ± 0.006. Since the reactivity ratios are the measure of distribution of monomer units in a copolymer chain, the values obtained are compared and discussed. This enables us to choose a suitable copolymer for synthesizing thermoset acrylic polymers, which are obtained from cross-linking of hydroxy functional groups of HPMA units, for specific end uses.     

Kinetic study on the radical polymerization of 2‐methacryloyloxyethyl phosphorylcholine

Polymerization of 2‐methacryloyloxyethyl phosphorylcholine (MPC) was kinetically investigated in ethanol using dimethyl 2,2′‐azobisisobutyrate (MAIB) as initiator. The overall activation energy of the homogeneous polymerization was calculated to be 71 kJ/mol. The polymerization rate (R_p) was expressed by R_p = k[MAIB]^0.54±0.05 [MPC]^1.8±0.1. The higher dependence of R_p on the monomer concentration comes from acceleration of propagation due to monomer aggregation and also from retardation of termination due to viscosity effect of the MPC monomer. Rate constants of propagation (k_p) and termination (k_t) of MPC were estimated by means of ESR to be k_p = 180 L/mol · s and k_t = 2.8 × 10⁴ L/mol · s at 60 °C, respectively. Because of much slower termination, R_p of MPC in ethanol was found at 60 °C to be 8 times that of methyl methacrylate (MMA) in benzene, though the different solvents were used for MPC and MMA. Polymerization of MPC with MAIB in ethanol was accelerated by the presence of water and retarded by the presence of benzene or acetonitrile. Poly(MPC) showed a peculiar solubility behavior; although poly(MPC) was highly soluble in ethanol and in water, it was insoluble in aqueous ethanol of water content of 7.4–39.8 vol %. The radical copolymerization of MPC (M₁) and styrene (St) (M₂) in ethanol at 50 °C gave the following copolymerization parameters similar to those of the copolymerization of MMA and St; r₁ = 0.39, r₂ = 0.46, Q₁ = 0.76, and e₁ = +0.51. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 509–515, 2000     

Synthesis and polymerization of optically active N-α-methylbenzylmaleimide

Optically active N-α-methylbenzylmaleimide (MBZMI) was prepared with maleic anhydride and d-(+)-α-methylbenzylamine. The polymerizations of MBZMI were carried out with α,α′-azobisisobutyronitrile (AIBN) and n-butyllithium (n-BuLi) in tetrahydrofuran (THF). The specific rotations of the polymers obtained by AIBN and n-BuLi initiator were +11.1° to +13.0° and ?57.0° to ?89.2°, respectively. The weight-average molecular weights (M_w) for the polymers were between 4200 and 8000. Furthermore, MBZMI was copolymerized with styrene (ST) and methyl methacrylate (MMA) with AIBN in THF at 50°C to obtain optically active copolymers. The monomer reactivity ratios of MBZMI (M₁) with ST (M₂) were obtained as r₁ = 0.027, r₂ = 0.094 in the MBZMI–ST and r₁ = 0.15, r₂ = 1.54 in the MBZMI–MMA system. The Q-e values for MBZMI were Q₁ = 0.78, e₁ = 1.62. All the polymers and copolymers were found to show a weakly negative circular dichroism (CD) peak at about 250 nm and a strongly positive CD peak at about 220 nm.     

Vinylhydroquinone. III. Copolymerization of vinylhydroquinone and vinyl monomers by tri-n-butylborane

The copolymerization of vinylhydroquinone (VHQ) and vinyl monomers, e.g., methyl methacrylate (MMA), 4-vinyl-pyridine (4VP), acrylamide (AA), and vinyl acetate (VAc), by tri-n-butylborane (TBB) was investigated in cyclohexanone at 30°C under nitrogen. VHQ is assumed to copolymerize with MMA, 4VP, and AA by vinyl polymerization. The following monomer reactivity ratios were obtained (VHQ = M₂): for MMA/VHQ/TBB, r₁ = 0.62, r₂ = 0.17; for 4VP/VHQ/TBB, r₁ = 0.57, r₂ = 0.05; for AA/VHQ/TBB, r₁ = 0.35, r₂ = 0.08. The Q and e values of VHQ were estimated on the basis of these reactivity ratios as Q = 1.4 and e = ?;1.1, which are similar to those of styrene. This suggests that VHQ behaves like styrene rather than as an inhibitor in the TBB-initiated copolymerization. No homopolymerization was observed either under nitrogen or in the presence of oxygen. The reaction mechanism is discussed.