Characterization and degradation of poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks

Poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks (PMPS–PMMA IPNs) were prepared by in situ sequential condensation of poly(methylphenylsiloxane) with tetramethyl orthosilicate and polymerization of methyl methacrylate. PMPS–PMMA IPNs were characterized by infrared (IR), differential scanning calorimetry (DSC), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The mobility of PMPS segments in IPNs, investigated by proton spin–spin relaxation T₂ measurements, is seriously restricted. The PMPS networks have influence on the average activation energy E_a,av of MMA segments in thermal degradation at initial conversion. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1717–1724, 1999     

Synthesis of end‐functionalized AB copolymers. II. Synthesis and characterization of carboxyl‐terminated poly(ethylene glycol)–poly(amino acid) block copolymers

AB block copolymers composed of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic poly(amino acid) with a carboxyl group at the end of PEG were synthesized with α‐carboxylic sodium‐ω‐amino‐PEG as a macroinitiator for the ring‐opening polymerization of N‐carboxy anhydride. Characterizations by ¹H NMR, IR, and gel permeation chromatography were carried out to confirm that the diblock copolymers were formed. In aqueous media this copolymer formed self‐associated polymer micelles that have a carboxyl group on the surface. The carboxyl groups located at the outer shell of the polymeric micelle were expected to combine with ligands to target specific cell populations. The diameter of the polymer micelles was in the range of 30–80 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3527–3536, 2004     

Synthesis and micellization of amphiphilic poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride) block copolymers

Amphiphilic biodegradable block copolymers [poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride)] were synthesized by the melt polycondensation of poly(ethylene glycol) and sebacic anhydride prepolymers. The chemical structure, crystalline nature, and phase behavior of the resulting copolymers were characterized with ¹H NMR, Fourier transform infrared, gel permeation chromatography, and differential scanning calorimetry. Microphase separation of the copolymers occurred, and the crystallinity of the poly(sebacic anhydride) (PSA) blocks diminished when the sebacic anhydride unit content in the copolymer was only 21.6%. ¹H NMR spectra carried out in CDCl₃ and D₂O were used to demonstrate the existence of hydrophobic PSA domains as the core of the micelle. In aqueous media, the copolymers formed micelles after precipitation from water‐miscible solvents. The effects on the micelle sizes due to the micelle preparation conditions, such as the organic phase, dropping rate of the polymer organic solution into the aqueous phase, and copolymer concentrations in the organic phase, were studied. There was an increase in the micelle size as the molecular weight of the PSA block was increased. The diameters of the copolymer micelles were also found to increase as the concentration of the copolymer dissolved in the organic phase was increased, and the dependence of the micelle diameters on the concentration of the copolymer varied with the copolymer composition. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1271–1278, 2006     

Depurination of synthetic poly(inosinic acid) analogues

A poly(inosinic acid) analogue, poly{[1′-(β-hypoxanthine-9-yl)-5′-deoxy-D -erythro-pent-4′-enofuranose]-alt-[maleic acid]} (4), was synthesized by the alternating copolymerization of nucleoside derivative 1 with maleic anhydride and subsequent hydrolysis. N-Glycosidic bonds of the polymer were spontaneously hydrolyzed to liberate hypoxanthine from the polymer backbone in a buffer solution (pH 7.4) at room temperature. The depurination rate constant of the polymer at pH 7.4 and 37°C was measured to be 1.9 × 10⁻⁶ sec⁻¹, which was 10⁵-fold higher than that (3 × 10⁻¹¹ sec⁻¹) of the depurination of DNA that occurred in the biological systems. The increase in the depurination rate was attributable to the high potential energy of the polymer caused by the crowded environment around the bases, so that the polymer was more susceptible to the hydrolysis. Since natural nucleic acids often have compact structures with the crowded environment around the bases by the intricate chain folding, the depurination may also be accelerated in a similar manner in the biological system. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3361–3365, 1999     

Characterization and degradation of the poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymer

Poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymers (PSXE-g-PMMA) were prepared by condensation reaction of poly(methylphenylsiloxane)-containing epoxy resin (PSXE) with carboxyl-terminated poly(methyl methacrylate) (PMMA), and they were characterized by gel permeation chromatography (GPC), infrared (IR), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The microstructure of the PSXE-g-PMMA graft copolymer was investigated by proton spin–spin relaxation T₂ measurements. The thermal stability and apparent activation energy for thermal degradation of these copolymers were studied by thermogravimetry and compared with unmodified PMMA. The incorporation of poly(methylphenylsiloxane) segments in graft copolymers improved thermal stability of PMMA and enhanced the activation energy for thermal degradation of PMMA. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2521–2530, 1998     

Synthesis and characterization of novel aromatic poly(imide–benzoxazole) copolymers

New poly(imide–benzoxazole) copolymers were prepared directly from a dianhydride, a diacid chloride, and a bis(o‐diaminophenol) monomer in a two‐step method. In the first step, poly(amic acid–hydroxyamide) precursors were synthesized by low‐temperature solution polymerization in an organic solvent. Subsequently, the thermal cyclodehydration of the poly(amic acid–hydroxyamide) precursors at 350 °C produced the corresponding poly(imide–benzoxazole) copolymers. The inherent viscosities of the precursor polymers were around 0.19–0.33 dL/g. The cyclized poly(imide–benzoxazole) copolymers had glass‐transition temperatures in the range of 331–377 °C. The 5% weight loss temperatures ranged from 524 to 535 °C in nitrogen and from 500 to 514 °C in air. The poly(imide–benzoxazole) copolymers were amorphous, as evidenced by the wide‐angle X‐ray diffraction measurements. The structures of the precursor copolymers and the fully cyclized copolymers were characterized by Fourier transform infrared, ¹H NMR, and elemental analysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6020–6027, 2005     

Effect of inert diluent segment on the miscibility behavior of poly(vinylphenol) with poly(acetoxystyrene) blends

Polymer blends of poly(vinylphenol) (PVPh) and poly(styrene‐co‐vinylphenol) with poly(p‐acetoxystyrene) (PAS) were prepared by solution casting from tetrahydrofuran solution. The thermal properties and hydrogen bonding of the blends were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy. Although hydrogen bonding existed between the PVPh and PAS segments, the experimental results indicated that PVPh is immiscible with PAS as shown by the existence of two glass‐transition temperatures over the entire composition range by DSC. This phenomenon is attributed to the strong self‐association of PVPh, intramolecular screening, and functional group accessibility effects of the PVPh/PAS blend system. However, the incorporation of an inert diluent moiety such as styrene into the PVPh chain renders the modified polymer to be miscible with PAS. Copolymers containing between 16 and 51 mol % vinylphenol were fully miscible with PAS according to DSC studies. These observed results were caused by the reduction of the strong self‐association of PVPh and the increase of the interassociation between PVPh and PAS segments with the incorporation of styrene on the PVPh chain. According to the Painter‐Coleman association model, the interassociation equilibrium constant of PVPh/PAS blends was determined by a model compound and polymer blend. Good correlation between these two methods was obtained after considering the intramolecular screening and functional group accessibility effect in the polymer blend. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1661–1672, 2002     

Microgels based on isotactic poly(styrene): Synthesis and characterization

Poly(styrene) microgels are known, but the influence of tacticity on particle formation and behavior has not been investigated yet. Isotactic poly(styrene) (iPS) with M_n = 15–120 kg/mol is synthesized by coordinate polymerization and cross‐linked by Friedel–Crafts alkylation in a miniemulsion. Nuclear magnetic resonance (NMR) spectroscopy, light microscopy, cryogenic transmission electron microscopy, and wide‐angle powder diffraction are applied to understand the structure of microgels obtained. Typically, spherical microgels with overall diameter of 40–500 nm are found. Isotacticity of the polymer is retained during microgel formation. Increase of cross‐linker content leads to partial crystallinity inside the microgel. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 175–180     

Synthesis of poly(vinylidene fluoride)‐b‐poly(styrene sulfonate) block copolymers by controlled radical polymerizations

Block copolymers based on poly(vinylidene fluoride), PVDF, and a series of poly(aromatic sulfonate) sequences were synthesized from controlled radical polymerizations (CRPs). According to the aromatic monomers, appropriate techniques of CRP were chosen: either iodine transfer polymerization (ITP) or atom transfer radical polymerization (ATRP) from PVDF‐I macromolecular chain transfer agents (CTAs) or PVDF‐CCl₃ macroinitiator, respectively. These precursors were produced either by ITP of VDF with C₆F₁₃I or by radical telomerization of VDF with chloroform, respectively. Poly(vinylidene fluoride)‐b‐poly(sodium styrene sulfonate), PVDF‐b‐PSSS, block copolymers were produced from both techniques via a direct polymerization of sodium styrene sulfonate (SSS) monomer or an indirect way with the use of styrene sulfonate ethyl ester (SSE) as a protected monomer. Although the reaction led to block copolymers, the kinetics of ITP of SSS showed that PVDF‐I macromolecular CTAs were not totally efficient because a limitation of the CTA consumption (56%) was observed. This was probably explained by both the low activity of the CTA (that contained inefficient PVDF‐CF₂CH₂? I) and a fast propagation rate of the monomer. That behavior was also noted in the ITP of SSE. On the other hand, ATRP of SSS initiated by PVDF‐CCl₃ was more controlled up to 50% of conversion leading to PVDF‐b‐PSSS block copolymer with an average number molar mass of 6000 g·mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and absorption/emission properties of novel poly(silylenearylenevinylene)s

Polymerization of p-(dimethylsilyl)phenylacetylene in toluene at 25 and 80 °C with RhI(PPh₃)₃ catalyst afforded highly regio- and stereoregular poly(dimethylsilylene-1,4-phenylenevinylene)s [cis- and trans-poly( 1a )s] containing 98% cis- and 99% trans-vinylene moieties, respectively. The trans-type polymers exhibited redshifts and hyperchromic effects in the ultraviolet–visible spectrum as compared with the cis-type counterparts. Photoirradiation of cis- and trans-poly( 1a )s gave cis-rich mixtures at equilibrium states. The trans and cis polymers exhibited different emission properties, for example—trans polymer, emissn λ_max = 400 nm, quantum yield: 3.4 × 10⁻³ and cis polymer, emissn λ_max = 380 nm, quantum yield: 1.5 × 10⁻³. Besides poly( 1a ), poly(dimethylsilylenearylenevinylene)s containing biphenylene and phenylenesilylenephenylene units [poly( 3 )] were prepared. The extent of conjugation in these polymers decreased in the orders of biphenylene > phenylene > phenylenesilylenephenylene as well as trans-vinylene > cis-vinylene. The quantum yield of the trans-rich polymer with biphenylene moiety was fairly large and 0.15. Polyaddition of 1,4-bis(dimethylsilyl)benzene and three types of diethynylarenes (4,4′-diethynylbiphenyl, 2,7-diethynylfluorene, and 2,6-diethynylnaphthalene) catalyzed by RhI(PPh₃)₃ provided novel regio- and stereoregular polymers [poly( 6 )]. These polymers displayed blue light emission with high quantum yields (4–81%). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3615–3624, 2003     

Photoluminescent properties of poly(p‐phenylene vinylene thiophene‐co‐siloxane)

A new p‐phenylene–vinylene–thiophene‐based siloxane block copolymer has been synthesized. The copolymer consists of alternating rigid and flexible blocks. The rigid blocks are composed of phenylene–vinylene–thiophene‐based units, and the flexible blocks are derived from 1,3‐dialkyldisiloxane units. The former component acts as the chromophore, and allows fine tuning of band gap for blue‐light emission, while the latter imparts good solubility of the copolymer in organic solvents, and thus, should enhance processibility of the resulting copolymer. The thermal properties of the copolymer have been characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The photoluminescence (PL) of the copolymer in solution and in cast film has been studied. The effects of concentration on the PL intensity of the new copolymer in polymer blends with poly(methyl methacrylate) (PMMA) and poly(vinyl carbazole) (PVK) have also been described. Efficient energy transfer from PVK to the new block copolymer in the blended film was observed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1450–1456, 2000     

Synthesis,structural analysis,and visualization of poly(2‐ethynyl‐9‐substituted carbazole)s and poly(3‐ethynyl‐9‐substituted carbazole)s containing chiral and achiral minidendritic substituents

The synthesis of 2‐ethynyl‐9‐substituted carbazole and 3‐ethynyl‐9‐substituted carbazole monomers containing first‐generation chiral and achiral dendritic (i.e., minidendritic) substituents, 2‐ethynyl‐9‐[3,4,5‐tris(dodecan‐1‐yloxy)benzyl]carbazole (2ECz), 3‐ethynyl‐9‐[3,4,5‐tris(dodecan‐1‐yloxy)benzyl]carbazole (3ECz), 2‐ethynyl‐9‐{3,4,5‐tris[(S)‐2‐methylbutan‐1‐yloxy]benzyl}carbazole (2ECz*), and 3‐ethynyl‐9‐{3,4,5‐tris[(S)‐2‐methylbutan‐1‐yloxy]benzyl}carbazole (3ECz*), is presented. All monomers were polymerized and copolymerized by stereospecific polymerization to produce cis‐transoidal soluble stereoisomers. A structural analysis of poly(2ECz), poly(2ECz*), poly(3ECz), poly(3ECz*), poly(2ECz*‐co‐2ECz), and poly(3ECz*‐co‐3ECz) by a combination of techniques, including ¹H NMR, ultraviolet–visible, and circular dichroism spectroscopy, thermal optical polarized microscopy, and X‐ray diffraction experiments, demonstrated that these polymers had a helical conformation that produced cylindrical macromolecules exhibiting chiral and achiral nematic phases. Individual chains of these cylindrical macromolecules were visualized by atomic force microscopy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3509–3533, 2002     

Synthesis and characterization of aromatic poly(ether ketone)s containing cyclotriphosphazene units

Bis(4-oxybenzoic acid) tetrakis(phenoxy) cyclotriphosphazene (IUPAC name: 4-[4-(carboxyphenoxy)-2,4,6,6-tetraphenoxy-1,3,5,2λ⁵,4λ⁵,6λ⁵-triazatriphosphinin-2-yl]oxy-benzoic acid) was synthesized and direct polycondensed with diphenylether or 1,4-diphenoxybenzene in Eaton's reagent at the temperature range of 80–120°C for 3 hours to give aromatic poly(ether ketone)s. Polycondensations at 120°C gave polymer of high molecular weight. Incorporation of cyclotriphosphazene groups in the aromatic poly(ether ketone) backbone greatly enhanced the solubility of these polymers in common organic polar solvents. Thermal stabilities by TGA for two polymer samples of polymer series ranged from 390 to 354°C in nitrogen at 10% weight loss and glass transition temperatures (T_g) ranged from 81.4 to 89.6°C by DSC. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1227–1232, 1998     

Transition metal compatibilization of poly(vinylamine) and poly(ethylene imine)

Poly(vinylamine), PVA, complexes with cobalt chloride hexahydrate exhibit a 45 °C enhancement in the glass‐transition temperature per mol % of the d‐block metal cation. Poly(ethylene imine), PEI, complexes with CoCl₂(H₂O)₆ exhibit a 20 °C enhancement in T_g per mol % Co²⁺. Since the basicities of primary and secondary amines are comparable (i.e., pK_b,PVA ≈ 3.34 vs. pK_b,PEI ≈ 3.27) and the rates at which each polymeric ligand displaces waters of hydration in the coordination sphere of Co²⁺ are similar, transition metal compatibilization is operative in blends of both polymers with CoCl₂(H₂O)₆. These two polymers are immiscible in the absence of the inorganic component. Infrared spectroscopy suggests that nitrogen lone pairs in PVA and PEI coordinate to Co²⁺. The stress–strain response of a 75/25 blend of PVA and PEI with 2 mol % Co²⁺ reveals a decrease in elastic modulus from 4.4 × 10⁹ N/m² to 5.7 × 10⁷ N/m², a decrease in fracture stress from 3.7 × 10⁷ N/m² to 2.0 × 10⁶ N/m², and an increase in ultimate strain from 1.3 to 12% relative to the 75/25 immiscible polymer–polymer blend. A plausible explanation for this effect is based on the fact that cobalt chloride hexahydrate compatibilizes both polymers by forming a coordination bridge between nitrogen lone pairs in dissimilar chains. Hence, poly(ethylene imine), which is very weak with a T_g near −40 °C, is integrated into a homogeneous structure with poly(vinylamine) and the mechanical properties of the individual polymers are averaged in the compatibilized ternary complex. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 552–561, 2000     

Synthesis and properties of poly (diphenylacetylenes) having aliphatic para-substituents

1-(p-t-Butylphenyl)-2-phenylacetylene and 1-(p-n-butylphenyl)-2-phenylacetylene were polymerized in catalytic systems based on TaCl₅ to give new polymers in high yields. These monomers were more reactive than diphenylacetylene (DPA) in copolymerization. Unlike poly (DPA), the present polymers were soluble in toluene, CHCl₃, etc. owing to the high configurational entropy induced by the para-substituents. Their relative weight-average molecular weights determined by GPC were in the range of 6 × 10⁵–36 × 10⁵, and films could be obtained by solution casting. These polymers were fairly thermally stable, as seen from their high onset temperatures (320–380°C) of weight loss in TGA in air. The oxygen permeability coefficient of the polymer with t-Bu group was 1100 barrers, the highest among those of all the hydrocarbon polymers. © 1994 John Wiley & Sons, Inc.     

New poly(amide–imide)s syntheses. XXIII. Synthesis and properties of poly(amide–imide)s derived from 4,4′‐[1,4‐phenylenebis(isopropylidene‐1,4‐phenyleneoxy)]dianiline and various bis(trimellitimide)s

A series of poly(amide–imide)s III_a–m containing flexible isopropylidene and ether groups in the backbone were synthesized by the direct polycondensation of 4,4′‐[1,4‐phenylenebis(isopropylidene‐1,4‐phenyleneoxy)]dianiline (PIDA) with various bis(trimellitimide)s II_a–m in N‐methyl‐2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. The resulting poly(amide–imide)s had inherent viscosities in the range of 0.80–1.36 dL/g. Except for those from the bis(trimellitimide)s of p‐phenylenediamine and benzidine, all the polymers could be cast from DMAc into transparent and tough films. They exhibited excellent solubility in polar solvents. The 10% weight loss temperatures of the polymers in air and in nitrogen were all above 495°C, and their T_g values were in the range of 201–252°C. Some properties of poly(amide–imide)s III were compared with those of the corresponding poly(amide–imide)s V prepared from the bis(trimellitimide) of diamine PIDA and various aromatic diamines. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 69–76, 1999     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Poly(phenyl methacrylate) and poly(1‐naphthyl methacrylate) prepared in microemulsions

Phenyl methacrylate and 1‐naphthyl methacrylate were polymerized in microemulsions using stearyltrimethylammonium chloride, cetyltrimethylammonium bromide, and a mixture of nonionic Triton surfactants to form latexes that were 20–30 nm in diameter. A temperature of 70 °C was needed to obtain polymers using thermal initiation. The tacticities of poly(phenyl methacrylate) (PPhMA) (55% rr) and poly(1‐naphthyl methacrylate) (P‐1‐NM) (47% rr) were the same as those of the polymers prepared in toluene solutions. The weight average molecular weights were 1 × 10⁶ and 5 × 10⁵ g/mol for PPhMA and P‐1‐NM prepared in microemulsions with very broad distributions. PPhMA samples from microemulsions and solution had the same T_g = 127 °C. P‐1‐NM from microemulsions had T_g = 145–147 °C compared with T_g = 142 °C for P‐1‐NM from solution. The molecular weights and the glass‐transition temperatures of both PPhMA and P‐1‐NM from microemulsions are substantially higher than any previously reported. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 519–524, 2001     

Synthesis and self‐association behavior of poly[bis(2‐(2‐methoxyethoxy)ethoxy)phosphazene]‐b‐poly(propyleneglycol) triblock copolymers

Amphilic triblock copolymers with varying ratios of hydrophilic poly[bis (methoxyethoxyethoxy)phosphazene] (MEEP) and relatively hydrophobic poly(propylene glycol) (PPG) blocks were synthesized via the controlled cationic‐induced living polymerization of a phosphoranimine (Cl₃P?NSiMe₃) at ambient temperature. A PPG block can function as either a classical hydrophobic block or a less hydrophobic component by varying the nature of a phosphazene block. The aqueous phase behavior of MEEP‐PPG‐MEEP block copolymers was investigated using fluorescence techniques, TEM, and dynamic light scattering (DLS). The critical micelle concentrations (cmcs) of MEEP‐PPG‐MEEP block copolymers were determined to be in the range of 3.7–16.8 mg/L. The mean diameters of MEEP‐PPG‐MEEP polymeric micelles, measured by DLS, were between 31 and 44 nm. The equilibrium constants of pyrene in these micelles ranged from 4.7 × 10⁴ to 9.6 × 10⁴. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 692–699, 2009     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997