海藻酸钠水凝胶固载细胞色素c的蛋白膜伏安法研究

用海藻酸钠(SA)水凝胶将细胞色素c(cyt-c)固定在棱面热解石墨电极(EPPGE)表面,形成稳定的SA-cyt-c/EPPGE电极,采用蛋白膜伏安法(PFV)研究了cyt-c与电极之间的直接电化学和离子强度、pH、外加金属离子对其电化学行为的影响及其电催化性能。结果表明:cyt-c中血红素辅基Fe(Ⅲ)/Fe(Ⅱ)电对表现出准可逆行为,pH7.0、NaCl浓度为0.1 mol/L时电化学活性最高,外加金属离子则有抑制作用,SA-cyt-c/EPPGE可催化还原O2,有可能发展成为一种溶解氧的生物传感器。     

不同离子液体中硝基苯的电化学还原

研究了硝基苯在N-甲基咪唑对甲基苯磺酸([Mim][PhSO3])和1-丁基-3-甲基咪唑六氟磷酸([Bmim][PF6])两种离子液体中的电化学还原反应.循环伏安法测试显示,硝基苯在[Mim][PhSO3]中只出现一个还原峰,是一个受扩散控制的不可逆电化学反应,而在[Bmim][PF6]中出现两对氧化还原峰,表明其还原产物随离子液体性质的不同而异.     

吡咯烷酮酸性离子液体中硼酸酯的催化合成

研究了硼酸与频哪醇和环己醇在离子液体1-甲基-2-吡咯烷酮硫酸氢盐（[Hnmp]HSO4）、1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim]BF4）及1-丁基-3-甲基咪唑六氟磷酸盐([Bmim]PF6)中生成2-环己氧基-4,4,5,5-四甲基-1,3,2-二氧硼烷的酯化反应。 考察了不同离子液体、反应温度、反应时间和离子液体与反应物物质的量比等对反应的影响。 结果表明,当n(硼酸)∶n(频哪醇)∶n(环己醇)∶n([Hnmp]HSO4)=1∶1∶1∶1,反应温度为70 ℃和反应时间为4 h时,硼酸酯的产率为72.5%,离子液体重复使用4次,催化活性无明显降低。     

碱性离子液体催化甘油合成1,2-甘油碳酸酯(英)

以离子液体为催化剂,在无溶剂体系中,考察了生物质平台化合物甘油转化1,2-甘油碳酸酯的反应.与酸性离子液体和常用无机碱性催化剂相比,碱性离子液体咪唑基1-丁基-3-甲基咪唑([Bmim]Im)、氢氧化1-丁基-3-甲基咪唑([Bmim]OH)、咪唑基1-烯丙基-3-甲基咪唑([Amim]Im)、氢氧化1-烯丙基-3-甲基咪唑([Amim]OH)在甘油与碳酸二甲酯的酯交换反应中表现出优异的活性.其中,以[Bmim]Im离子液体为催化剂时甘油转化率为98.4%和甘油碳酸酯选择性接近100%.另外,该离子液体可以回收重复利用3次后甘油转化率仍可达92%,甘油碳酸酯选择性可近100%.此碱性离子液体催化方法具有反应结果较好、产物分离简单、条件温和以及环境友好等特点.     

Effect of the structure of imidazolium cations in [BF4](-)-type ionic liquids on direct electrochemistry and electrocatalysis of horseradish peroxidase in Nafion films

The direct electrochemistry and bioelectrocatalysis of horseradish peroxidase (HRP) in Nafion films at glassy carbon electrode (GCE) was investigated in three [BF(4)](-)-type room-temperature ionic liquids (ILs) to understand the structural effect of imidazolium cations. The three ILs are 1-ethyl-3-methylimidazolium tetrafluoroborate ([Emim][BF(4)]), 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF(4)]) and 1-hexyl-3-methylimidazolium tetrafluoroborate ([Hmim][BF(4)]). A small amount of water in the three ILs is indispensable for maintaining the electrochemical activity of HRP in Nafion films, and the optimum water contents decrease with the increase of alkyl chain length on imidazole ring. Analysis shows that the optimum water contents are primarily determined by the hydrophilicity of ILs used. In contrast to aqueous medium, ILs media facilitate the direct electron transfer of HRP, and the electrochemical parameters obtained in different ILs are obviously related to the nature of ILs. The direct electron transfer between HRP and GCE is a surface-confined quasi-reversible single electron transfer process. The apparent heterogeneous electron transfer rate constant decreases gradually with the increase of alkyl chain length on imidazole ring, but the changing extent is relatively small. The electrocatalytic reduction current of H(2)O(2) at the present electrode decreases obviously with the increase of alkyl chain length, and the mass transfer of H(2)O(2) via diffusion in ILs should be responsible for the change. In addition, the modified electrode has good stability and reproducibility; the ability to tolerate high levels of F(-) has been greatly enhanced due to the use of Nafion film. When an appropriate mediator is included in the sensing layer, a sensitive nonaqueous biosensor could be fabricated.     

Study of Imidazolium Ionic Liquids:Temperature-dependent Fluorescence and Molecular Dynamics Simulation

The steady-state fluorescence spectra and molecular dynamics simulations were explored to investigate the temperature dependent organization in some imidazolium ionic liquids:1-butyl-3-methylimidazolium hexafluo-rophosphate([bmim][PF6]),1-ethyl-3-methylimidazolium ethylsulfate([emim][EtSO4]) and 1-butyl-3-methylimida-zolium tetrafluoroborate([bmim][BF4]).The pure room temperature ionic liquids(ILs) exhibit a large red shift at more than an excitation wavelength of around 340 nm,which demonstrates the hetero...     

Density and Viscosity for Binary Mixtures of the Ionic Liquid 1-Butyl-3-methylimidazolium Tetrafluoroborate with 2-Propanol,N,N-Dimethylacetamide and N,N-Dimethylformamide at 293.15–323.15 K: Experimental and PC-SAFT Modeling

Journal of Solution Chemistry - For three binary mixtures composed of ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF4]) with 2-propanol, N,N?dimethylacetamide (DMA) and...     

Experiments and model for the surface tension of (MDEA + [Bmim][BF4]) and (MDEA + [Bmim][Br]) aqueous solutions

The surface tension (γ) of 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF₄]), 1-butyl-3-methylimidazolium bromide ([Bmim][Br]), (N-methyldiethanolamine(MDEA) + [Bmim][BF₄]) and (MDEA + [Bmim][Br]) aqueous solutions were measured by using the BZY-1 surface tension meter. The temperature ranged from (293.2 to 323.2) K. The mass fraction of MDEA ranged from 0.35 to 0.45. A thermodynamic equation was proposed to model the surface tension of (MDEA + ionic liquids) (ILS) aqueous solutions and the calculated results agreed well with the experiments. The effects of temperature, mass fractions of MDEA and ILS on the surface tension were demonstrated on the basis of experiments and calculations.     

细胞色素C在离子液体修饰电极上的电化学行为

分别合成了疏水和亲水性咪唑类离子液体,并制备了相应的两种离子液体修饰的玻碳电极。循环伏安法测量结果显示,细胞色素C在离子液体修饰的玻碳电极上的电子传递过程为一扩散控制的准可逆反应,表明咪唑类离子液体也可用作细胞色素C电子传递的有效促进剂。电化学交流阻抗谱的测量结果得到了与循环伏安相同的结论。     

Thermodynamic Properties of Binary Mixtures of the Amino Acid Ionic Liquids [Bmim][Glu] or [Bmim][Gly] with Methanol at T=298.15 to 313.15 K

Densities, viscosities and refractive indices were determined for two ionic liquid mixtures formed by the 1-butyl-3-methylimidazolium glutamic acid salt ([Bmim][Glu]) or the 1-butyl-3-methylimidazolium glycine acid salt ([Bmim][Gly]), respectively, with methanol over the mole fraction from 0.1 to 0.9 and at temperatures ranging from 298.15 K to 313.15 K at intervals of 5 K and at atmospheric pressure. Excess molar volumes, viscosity deviations and refractive index deviations have been calculated from the experimental data and fitted to a Redlich–Kister polynomial function. The results have been interpreted in terms of ion-dipole interactions, and structural factors of the ionic liquid and alcohol molecular liquids.     

Direct electrochemistry of cytochrome <Emphasis Type="Italic">c</Emphasis> entrapped in agarose hydrogel by protein film voltammetry

Cytochrome c (cyt-c) entrapped in agarose hydrogel was electrostatically bound to the edge plane pyrolytic graphite electrode (EPPGE), and then stable agarose-cyt-c/EPPGE was prepared. Direct electrochemistry between cyt-c and the EPPGE was monitored by protein film voltammetry. The effects of ionic strength, pH and exterior substances on the direct electrochemistry, and electrocatalytic properties of cyt-c were also studied. Results show that the electrochemical behavior of heme Fe(III)/Fe(II) in cyt-c is quasireversible. Its electrochemical performance is the best when the concentration of supporting electrolyte phosphate buffer solution is 0.2 mol/l and pH is 7.0, and greatly inhibited by exterior metal ions. Catalytic reduction of oxygen could also be achieved at the agarose-cyt-c/EPPGE.     

Glycolysis of poly(ethylene terephthalate) (PET) using basic ionic liquids as catalysts

The glycolysis of poly(ethylene terephthalate) (PET) was studied using several ionic liquids and basic ionic liquids as catalysts. The basic ionic liquid, 1-butyl-3-methylimidazolium hydroxyl ([Bmim]OH), exhibits higher catalytic activity for the glycolysis of PET, compared with 1-butyl-3-methylimidazolium bicarbonate ([Bmim]HCO₃), 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) and 1-butyl-3-methylimidazolium bromide ([Bmim]Br). FT-IR, ¹H NMR and DSC were used to confirm the main product of glycolysis was bis(2-hydroxyethyl) terephthalate (BHET) monomer. The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and dosages of ethylene glycol on the conversion of PET, yield of BHET were investigated. The results showed a strong influence of the mixture evolution of temperature and reaction time on depolymerization of PET. Under the optimum conditions of m(PET):m(EG): 1:10, dosage of [Bmim]OH at 0.1 g (5 wt%), reaction temperature 190 °C and time 2 h, the conversion of PET and the yield of BHET were 100% and 71.2% respectively. Balance between the polymerization of BHET and depolymerization of PET could be changed when the reaction time was more than 2 h and contents of catalyst and EG were changed.     

Surface tension of binary mixtures of imidazolium and ammonium based ionic liquids with alcohols, or water: cation, anion effect

The surface tensions were measured at atmospheric pressure, with use of a ring tensiometer, of a series of alcoholic solutions of closely related ionic liquids: 1-methyl-3-methylimidazolium methylsulfate, [MMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium methylsulfate, [BMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium octylsulfate, [BMIM][OcSO4] in alcohol (methanol, or 1-butanol at 298.15 K) and of 1-hexyloxymethyl-3-methylimidazolium tetrafluoroborate, [C6H(13)OCH2MIM][BF4], 1,3-dihexyloxymethylimidazolium tetrafluoroborate, [(C6H13OCH2)2IM][BF4] in alcohol (methanol, or 1-butanol, or 1-hexanol at 308.15 and 318.5 K) and hexyl(2-hydroxyethyl)dimethylammonium bromide, C6Br in 1-octanol at 298.15 K. The set of ammonium ionic liquids of different cations and anions (C2Br, C2BF4, C2PF6, C2N(CN)2, C3Br, C4Br and C6Br) was chosen to show the influence of small amount of the ammonium ionic liquid on the surface tension of water at 298.15 K. The influence of the cation, or anion alkyl chain length on the properties under study (densities and surface tension) was tested.     

Microwave-assisted separation of ionic liquids from aqueous solution of ionic liquids

Microwave-assisted separation has been applied to recover ionic liquid (IL) from its aqueous solution as an efficient method with respect to time and energy compared to the conventional vacuum distillation. Hydrophilic ILs such as 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF(4)]), 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([Bmim][TfO]) and 1-ethyl-3-methylimidazolium methylsulfate ([Emim][MS]) could be recovered in 6 min from the mixture of ILs and water (1:1, w/w) under microwave irradiation at constant power of 10 W while it took at least 240 min to obtain ILs containing same water content (less than 0.5 wt%) by conventional vacuum oven at 363.15 K with 90 kPa of vacuum pressure. Energy consumptions per gram of evaporated water from the homogeneous mixture of hydrophilic ILs and water (1:1, w/w) by microwave-assisted separation were at least 52 times more efficient than those in conventional vacuum oven. It demonstrated that microwave-assisted separation could be used for complete recovery of ILs in sense of time and energy as well as relevant purity.     

离子液体/H_2O_2体系脱硫实验研究

选取四种不同种类离子液体(ILs),1-丁基-3-甲基咪唑溴化物([Bmim]Br)、1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF_4)、1-丁基-3-甲基咪唑硫酸氢盐([Bmim]HSO_4)、1-丁基-3-甲基咪唑磷酸二氢盐([Bmim]H_2PO_4)与30%H_2O_2溶液在温和条件下对两种高硫脱灰煤样(LS、QX)进行脱硫实验研究。用化学法测定脱硫前后煤样形态硫含量,并利用傅里叶变换红外光谱(FT-IR)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)及热重(TG)对脱硫前后的煤样进行表征。结果表明,离子液体的加入使H_2O_2氧化脱硫能力增强,煤中硫铁矿硫和有机硫化物硫被显著脱除;经ILs/H_2O_2体系作用后的煤样中小粒径的颗粒减少,颗粒间的缝隙增大,煤表面的凹坑明显,热重实验结果表明,ILs/H_2O_2体系作用后的煤样相对于原煤热失重增大,部分挥发性物质释放峰温提前。     

Direct electrochemistry and electrocatalysis of heme proteins entrapped in agarose hydrogel films in room-temperature ionic liquids

The electrochemistry and electrocatalysis of a number of heme proteins entrapped in agarose hydrogel films in the room-temperature ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF(6)]) have been investigated. UV-vis and FTIR spectroscopy show that the heme proteins retain their native structure in agarose film. The uniform distribution of hemoglobin in agarose-dimethylformamide film was demonstrated by atomic force microscopy. Cyclic voltammetry shows that direct electron transfer between the heme proteins and glassy carbon electrode is quasi-reversible in [bmim][PF(6)]. The redox potentials for hemoglobin, myoglobin, horseradish peroxidase, cytochrome c, and catalase were found to be more negative than those in aqueous solution. The charge-transfer coefficient and the apparent electron-transfer rate constant for these heme proteins in [bmim][PF(6)] were calculated from the peak-to-peak separation as a function of scan rate. The heme proteins catalyze the electroreduction of trichloroacetic acid and tert-butyl hydroperoxide in [bmim][PF(6)]. The kinetic parameter I(max) (maximum current at saturation concentration of substrate) and the apparent K(m) (Michaelis-Menten constant) for the electrocatalytic reactions were evaluated.     

Nucleophilicity in ionic liquids. 3. Anion effects on halide nucleophilicity in a series of 1-butyl-3-methylimidazolium ionic liquids

We have continued the study of halide nucleophilicity in ionic liquids, concentrating on the effect of changing the anion ([BF(4)](-), [PF(6)](-), [SbF(6)](-), [OTf](-), and [N(Tf)(2)](-)) when the cation is [bmim](+) (where bmim = 1-butyl-3-methylimidazolium). It was found that the nucleophilicities of all the halides were lower in all of the ionic liquids than in dichloromethane. Changing the anion affected the order of halide nucleophilicity, e.g., in [bmim][BF(4)] the order of nucleophilicity was Cl(-)>Br(-)>I(-) while in [bmim][N(Tf)(2)] the order was Cl(-)相似文献   

Thermodynamic studies of ionic interactions in aqueous solutions of imidazolium-based ionic liquids [Emim][Br] and [Bmim][Cl

Experimental measurements of density at different temperatures ranging from 293.15 to 313.15 K, the speed of sound and osmotic coefficients at 298.15 K for aqueous solution of 1-ethyl-3-methylimidazolium bromide ([Emim][Br]), and osmotic coefficients at 298.15 K for aqueous solutions of 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]) in the dilute concentration region are taken. The data are used to obtain compressibilities, expansivity, apparent and limiting molar properties, internal pressure, activity, and activity coefficients for [Emim][Br] in aqueous solutions. Experimental activity coefficient data are compared with that obtained from Debye-Hückel and Pitzer models. The activity data are further used to obtain the hydration number and the osmotic second virial coefficients of ionic liquids. Partial molar entropies of [Bmim][Cl] are also obtained using the free-energy and enthalpy data. The distance of the closest approach of ions is estimated using the activity data for ILs in aqueous solutions and is compared with that of X-ray data analysis in the solid phase. The measured data show that the concentration dependence for aqueous solutions of [Emim][Br] can be accounted for in terms of the hydrophobic hydration of ions and that this IL exhibits Coulombic interactions as well as hydrophobic hydration for both the cations and anions. The small hydration numbers for the studied ILs indicate that the low charge density of cations and their hydrophobic nature is responsible for the formation of the water-structure-enforced ion pairs.     

Copolymers dispersions designed to shaping of ceramic materials

Journal of Thermal Analysis and Calorimetry - To study the effect of ionic liquids (ILs) of the microstructure on the surface of the coal, four ILs ([Emim][BF4], [Bmim][BF4], [Bmim][NO3], and...     

Facile synthesis of thiourea derivatives in ionic liquid

The synthesis of cinnamoyl thiourea derivatives from cinnamoyl isothiocyanate (CIT) with substituted aniline (RC6H4NH2) was investigated in the mostly used ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, [Bmim][BF4]. Significant enhance-ments in reactivity, yield and reaction rate were achieved. The products could be recovered by simple filtration. [Bmim][BF4] couldbe recycled simply by removing water under vacuum and reused at least 9 times without significant decrease in activity.