时间延迟对偶极子光导天线空间功率合成影响分析

对偶极子光导天线空间功率合成中时间延迟的影响进行了分析。利用太赫兹时域光谱技术分别获取了34, 500, 1000 m偶极子光导天线的太赫兹时域光谱。采用数值模拟方法分析时间延迟对空间功率合成的影响。结果发现:在满足空间功率合成时域相干度60%的条件下,两个34, 500, 1000 m偶极子光导天线阵列的相对最大时间延迟分别为350.7, 467.6, 450.9 fs;三个34, 500, 1000 m偶极子光导天线阵列的相对最大时间延迟分别为191.1, 250.5, 267.2 fs;四个34, 500, 1000 m偶极子光导天线阵列的相对最大时间延迟分别为167, 200.4, 217.1 fs。试验结果表明,空间功率合成数值模拟仿真能为偶极子光导天线阵列的物理实验提供重要依据。     

GaAs光电导天线辐射太赫兹波功率的计算

在Larmor公式的基础上建立了适合计算光电导天线辐射太赫兹波功率的数学模型,利用此数学模型通过蒙特卡罗方法分别计算了不同实验条件下GaAs光电导天线辐射太赫兹电磁波功率.计算结果表明,增加光电导天线的偏置电场或触发光能量,都能够提高天线辐射太赫兹波功率,大孔径光电导天线能够承载更多的光生载流子,因而可以产生比小孔径光电导天线功率更高的太赫兹波. 关键词： 光电导天线 Larmor公式 太赫兹波功率     

基于光导微探针的近场/远场可扫描太赫兹光谱技术

太赫兹技术已经成为涉及公共安全、军事国防和国民经济等国家核心利益的前沿研究领域.以往太赫兹测量技术中通常以远场测量为主,如常用的太赫兹时域光谱仪.近年来太赫兹近场技术得到了迅猛的发展,特别是基于光导天线的探针技术的发展,为可扫描的太赫兹近场测量提供了可能.本文详细报道了我们近期在可扫描太赫兹近场光谱仪研究中的进展.采用光纤耦合的光导微探针实现了方便灵活的太赫兹近场/远场三维扫描,并同时获得振幅和相位信息.该系统将有可能广泛应用于人工微结构、石墨烯、表面等离子激元、波导传输、近场成像、生物样品检测、芯片检测等研究领域.     

平面天线在场效应晶体管太赫兹探测器中的应用

为了提高场效应晶体管太赫兹探测器的响应度并降低噪声等效功率,需要对探测器集成平面天线的结构进行合理设计与优化,本文对集成平面天线结构的场效应晶体管太赫兹探测器的研究进行了深入调研。首先,对场效应晶体管太赫兹探测器的工作原理进行了分析,介绍了集成平面天线如何解决耦合太赫兹波效率低的问题。然后,介绍了一些常用的平面天线结构,包括偶极子天线、贴片天线、缝隙天线、grating-gate和其他类型的结构,比较了各种天线的性能以及引入后对太赫兹探测器响应度的影响。通过对比不同天线结构的探测器响应度和噪声等效功率等参数指标,发现:采用平面天线结构之后,场效应晶体管太赫兹探测器的响应度有了大幅度的提升,各种类型的天线对探测器响应度都有不同程度的提升。本文着重介绍了几种集成于场效应晶体管的平面天线结构,包括各种天线的性能和研究进展,最后分析了场效应晶体管太赫兹探测器存在的问题和发展趋势。     

栅极天线和NMOS耦合的CMOS太赫兹热探测器的设计与测试

设计了一种在室温工作的太赫兹热探测器.探测器由片上天线和温度传感器耦合而成.天线由NMOS温度传感器的栅极组成,吸收入射的太赫兹波将其转化为焦耳热,生成的热量引起的温度变化由温度传感器探测.整个探测器的探测过程分为电磁辐射吸收、波-热转换、热-电转换三个过程,并分别进行了建模分析,仿真得到天线吸收率为0.897,热转换效率为165K/W,热电转换效率为1.77mV/K.探测器基于CMOS 0.18μm工艺设计,工艺处理后将硅衬底打薄至300μm.探测器在3THz太赫兹环境下,入射功率为1mW时,电压响应率仿真值为262mV/W,测试值为148.83mV/W.     

玻璃纤维蜂窝复合材料的太赫兹无损检测技术(英文)

采用双高斯脉冲反卷积滤波技术对太赫兹时域波形进行滤波优化,提出一种基于太赫兹时域光谱无损检测的太赫兹反射式层析成像技术,用于分析玻璃纤维蜂窝复合材料的粘接质量.结合玻璃纤维蜂窝复合材料结构的特点,分别在蜂窝上层胶膜和下层胶膜中设计了不同直径的圆形和梯形脱粘缺陷,在此基础上,完成了脱粘缺陷蜂窝结构样品的制作.提出的太赫兹反射式层析成像和B-scan成像方法,适用于玻璃纤维蜂窝复合材料的脱粘缺陷分析.针对反射式层析成像图像对比度差的问题,结合脱粘缺陷处的太赫兹时域波形数据特征,采用缺陷特征时间区域成像优化技术,提高了脱粘缺陷的检测能力和识别准确率,实现了玻璃纤维蜂窝材料的上层脱粘厚度50μm、下层脱粘厚度50μm缺陷的太赫兹无损检测.     

光电导天线太赫兹辐射峰值调控研究

针对微结构光电导天线与飞秒激光之间相互作用效应以及辐射太赫兹波调控问题进行了研究。采用德鲁德-洛伦兹理论模型获得微结构光电导天线辐射光电流密度,通过时域有限差分把光电流密度迭代在激励网格上,结合麦克斯韦方程求解时变电磁场,并通过传输线格林函数获得多层介质近场到远场的辐射太赫兹波,建立了辐射光电流与辐射阻抗、电磁共振模式之间的关系模型,模拟仿真分析了微结构S型光电导天线太赫兹波辐射调控机理。研究结果表明:微结构改变了天线等效模型的辐射阻抗;同时得知耦合系数不为零时存在耦合作用,且随着耦合系数增大共振频率峰值发生辐射增强和位移;并通过设计S型光电导天线获得辐射峰值频率调整范围为0.50~0.80 THz之间,对比工形天线辐射峰值频率由原来的0.40 T移动到0.76 T,频率调整度75%,峰值辐射效率约提高70%。该研究工作为后续高功率光导天线太赫兹波辐射的共振中心频点以及结构设计奠定重要基础。     

基于金属孔阵列的聚酰亚胺薄膜太赫兹探测

优化设计了多种不同孔径和形状的太赫兹波段的亚波长金属孔阵列结构,结合超薄低折射率的聚酰亚胺（PI）薄膜,探索了太赫兹时域光谱技术对超薄低折射率的探测灵敏性。利用飞秒微加工技术制备了一系列亚波长金属孔阵列结构,利用太赫兹时域光谱技术测试了阵列结构的反射波谱,获得了强烈的反射共振现象。然后在亚波长金属孔阵列结构背面叠加PI薄膜,结果表明太赫兹反射峰出现了显著低频移动现象。利用这一现象,实现了低至10 m的PI薄膜的有效探测,说明亚波长金属孔阵列结构在太赫兹传感领域对检测超薄低折射率薄膜材料有极强敏感性。收稿日期:; 修订日期:     

基于衰减全反射式太赫兹时域光谱技术的食用油光谱特性研究

食用油是人类营养和能量的重要来源,为人体提供必需的脂肪酸,研究食用油在太赫兹波段光学特性,对食用油成分分析及品质评价具有重要价值。衰减全反射式太赫兹时域光谱技术是一种新型的太赫兹时域光谱技术,通过样品与倏逝波的相互作用,获取样品的太赫兹光谱。与透射式或反射式太赫兹时域光谱技术相比,该技术能有效地避免测量食用油等液体样品时样品池对光学参数的影响,并能获得样品的精确光学参数。分别利用透射式太赫兹时域光谱技术和衰减全反射式太赫兹时域光谱技术测量了大豆油的吸收光谱。结果表明,与透射式太赫兹时域光谱技术相比,衰减全反射式太赫兹时域光谱技术能更有效地提取大豆油的吸收系数、吸收峰分布等光学特性。进一步利用衰减全反射式太赫兹时域光谱技术研究了大豆油、核桃油、葡萄籽油在太赫兹波段的光学特性,获得了三种食用油在1~1.8 THz范围内的折射率谱和吸收光谱。利用密度泛函理论计算了食用油中四种主要成分(软脂酸、硬脂酸、油酸和亚油酸)在太赫兹波段的振动、转动模式,理论计算结果同实验测量结果吻合较好。研究表明,在太赫兹波段食用油的吸收峰与所含脂肪酸分子种类与含量有关,其主要来源为脂肪酸分子的低频振动和转动。研究成果对食用油成分定性定量分析及品质检测等具有指导意义。     

基于微流控芯片的钾盐溶液太赫兹光谱特性研究

许多生物分子的振动及转动能级都在太赫兹波段,因此太赫兹时域光谱技术可以用来探测生物分子。并且由于太赫兹波的光子能量较低,仅为毫电子伏量级,在探测过程中不会破坏生物样品,所以太赫兹时域光谱技术在未来生化检测等研究领域具有非常广泛的应用前景。研究表明,大多数生物分子需要在液体环境中才能充分发挥其生物活性,然而水溶液中的氢键在太赫兹波段会产生强烈的吸收。另外,水分子是极性分子,太赫兹波对极性分子也有很强的共振吸收,这使得利用太赫兹时域光谱技术检测液体环境中的活性生物分子非常困难。因此,许多研究团队将太赫兹时域光谱技术与微流控技术相结合,以减少各种因素对生物分子检测的影响。微流控技术是通过减小微流控芯片中液体池的深度来减少液体样品与太赫兹波的作用距离,从而减少水溶液对太赫兹波的吸收。使用对太赫兹波的透过率高达95%的环烯烃共聚物(COC:Zeonor 1420R)为材料制作了双层微流控芯片,该微流控芯片内部液体池的长度和宽度均为4 cm,深度为50μm。此外,由于在电解质溶液中存在大量自由移动的阴阳离子,所以为了探究电解质溶液中自由移动的阴阳离子对太赫兹透射特性的影响,使用外加电场装置对注入液...     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.