Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术，利用LSCO/CeO₂/YSZ多异质缓冲层，在Si(100)基 片上成功地制备了c轴一致取向的Bi_3.15Nd_0.85Ti₃O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构 、取向和形貌特征，考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响，确定 了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型 的蝴蝶形曲线，表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与 薄膜取向的相关性. 关键词： 3.15Nd_0.85Ti₃O₁₂')" href="#">Bi_3.15Nd_0.85Ti₃O₁₂ 铁电薄 膜 多层异质结 脉冲激光沉积     

Characterization of Y2O3 gate dielectric on n-GaAs substrates

Physical and electrical properties of sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate are investigated. The as-deposited films and interfacial layer formation have been analyzed by using X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). It is found that directly deposited Y₂O₃ on n-GaAs exhibits excellent electrical properties with low frequency dispersion (<5%), hysteresis voltage (0.24 V), and interface trap density (3 × 10¹² eV⁻¹ cm⁻²). The results show that the deposition of Y₂O₃ on n-GaAs can be an effective way to improve the interface quality by the suppression on native oxides formation, especially arsenic oxide which causes Fermi level pinning at high-k/GaAs interface. The Al/Y₂O₃/n-GaAs stack with an equivalent oxide thickness (EOT) of 2.1 nm shows a leakage current density of 3.6 × 10⁻⁶ A cm⁻² at a V_FB of 1 V. While the low-field leakage current conduction mechanism has been found to be dominated by the Schottky emission, Poole-Frenkel emission takes over at high electric fields. The energy band alignment of Y₂O₃ films on n-GaAs substrate is extracted from detailed XPS measurements. The valence and conduction band offsets at Y₂O₃/n-GaAs interfaces are found to be 2.14 and 2.21 eV, respectively.     

Structural investigations of TiO2:Tb thin films by X-ray diffraction and atomic force microscopy

In this work, structural investigations of TiO₂ thin films doped with Tb at the amount of 0.4, 2 and 2.6 at.% have been outlined. Thin films were deposited on Si and SiO₂ substrates by high energy reactive magnetron sputtering from mosaic Ti-Tb target. The influence of Tb dopant amount, post-annealing treatment and kind of applied substrate on microstructure has been discussed. Thin films were investigated by means of X-ray diffraction (XRD) and atomic force microscopy (AFM). XRD analysis revealed the existence of crystalline TiO₂ in anatase and rutile forms, depending on Tb amount in examined samples. AFM images show that as-deposited samples with 0.4 at.% concentration of terbium (anatase structure) have bigger crystallites as compared to 2% and 2.6 at.% of Tb (rutile structure). The additional annealing at 1070 K results in a mixed anatase (77%) and rutile (23%) structure.     

Development of rf plasma sputtered Al2O3-TiO2 multilayer broad band antireflecting coatings and its correlation with plasma parameters

TiO₂/Al₂O₃/TiO₂/Al₂O₃ multilayer structures were obtained at different oxygen:argon gas ratios of 20:80, 30:70, 50:50 and 60:40 sccm and constant rf power of 200 W using reactive magnetron sputtering. Grain size and elemental distribution in the films were studied from AFM image and XPS spectra respectively. The deposited grain size increased with increasing oxygen:argon gas ratio. The optical band gap, refractive index, extinction coefficient were calculated from UV-vis transmittance and reflectance spectra. It was observed that the value of refractive index, extinction coefficient and band gap increased with increasing oxygen. These variations are due to the defects levels generated by the heterostructure and explained by the PL spectrum. The antireflecting (AR) efficiency of the films was estimated from the reflectance spectra of the films. Broad band antireflecting coating for the visible range was achieved by varying oxygen content in the film. The plasma chemistry controlled the antireflecting property by the interface interdiffusion of atoms during layer transition in multilayer deposition. The in situ investigation of the plasma chemistry was performed using optical emission spectroscopy. The plasma parameters were estimated and correlated with the characteristics of the films.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

Composition-dependent structural and electrical properties of PbSe1−xTex thin films

Polycrystalline PbSe_1−xTe_x ingots were prepared by solid-state microwave synthesis. Thin films of PbSe_1−xTe_x were then deposited onto clean glass substrates using vacuum evaporation technique. Their nanostructure morphologies and stoichiometric ratio were examined using scanning electron microscopy (SEM) and energy dispersive X-ray spectra (EDX). X-ray diffraction (XRD) patterns indicated that the lattice constants of PbSe_1−xTe_x powders and thin films increased with the increasing amount of Te. From the electrical property measurements, the thin films were characterized by n-type behavior.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

Investigation of structural and magnetic properties of Ni, NiFe and NiFe2O4 thin films

Soft magnetic thin films of Ni, NiFe and NiFe₂O₄ were prepared using reactive magnetron sputtering in various deposition conditions. Experimentally observed soft magnetic property was compared and correlated with nanocrystalline structure evolution. Ni and NiFe deposited films are textured with fcc(111) phase preferred orientation. Accordingly, grain size and lattice parameter were calculated from X-ray diffraction (111) peak line width and 2θ peak position. Addition of reactive gas oxygen in deposition process has substantial effect on crystalline structure of film. There is phase transition from the ordered NiFe (111) structure to the NiFe₂O₄ nanocrystalline phase. The resulting film has shown small X-ray diffraction intensity peak corresponding to (311) and (400) orientation, indicating small amount of existing NiFe₂O₄ phase. The mechanism has been discussed to be responsible for nanocrystallization and amorphization of NiFe₂O₄ films. Magnetic measurement (M-H) loop reveal soft magnetic nature of films with magnetic anisotropy. The coercivity (H_c) of films is in accordance with random anisotropy model, where H_c reduced with grain size. The structural transformation was supported by Fourier transforms infrared spectroscopy measurement. The films are highly smooth with surface roughness in the range of ∼0.53-0.93 nm. NiFe₂O₄ films have shown lowest surface roughness with highest electrical resistivity values. The structural, surface, magnetic and infrared spectroscopy results are observed and analyzed.     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

Optimization of annealing conditions of In2S3 thin films deposited by vacuum thermal evaporation

In₂S₃ thin films were grown on glass substrates by means of the vacuum thermal evaporation technique and subsequently thermally annealed in nitrogen and free air atmosphere from 250 to 350 °C for different durations. Experimental parameters have been adjusted in order to optimize the annealing conditions, and to obtain high band gap energy at low deposition temperature, as required for photovoltaic applications. In order to improve our understanding of the influence of the deposition and annealing parameters on device performance, we have investigated our indium sulfide material by X-ray diffraction, energy dispersive X-ray analysis (EDAX), atomic force microscopy (AFM) and spectrophotometry. The optical and structural properties of the films were studied as a function of the annealing temperature and durations. X-ray diffraction analysis shows the initial amorphous nature of deposited In-S thin films and the phase transition into crystalline In₂S₃ upon thermal annealing. Films show a good homogeneity and optical direct band gap energy about 2.2 eV. An annealing temperature of 350 °C during 60 min in air atmosphere were the optimal conditions.     

N掺杂Cu2O薄膜的光学性质及第一性原理分析

采用射频磁控溅射技术, 在不同温度下制备了N掺杂Cu₂O薄膜．透射光谱分析发现, N掺杂导致Cu₂O成为允许的带隙直接跃迁半导体, 并使Cu₂O的光学禁带宽度增加．不同温度下沉积的薄膜光学禁带宽度E_g=2.52± 0.03 eV．第一性原理计算表明, N掺杂导致Cu₂O的禁带宽度增加了约25%, 主要与价带顶下移和导带底上移有关, 与实验报道基本符合．N的2p电子态分布不同于O原子, 在价带顶附近具有较大的态密度是N掺杂Cu₂O变成允许的带隙直接跃迁半导体的根本原因．     

Density, thickness and composition measurements of TiO2SiO2 thin films by coupling X-ray reflectometry, ellipsometry and electron probe microanalysis-X

Mixed TiO₂SiO₂ thin films were deposited by aerosol atmospheric CVD method by using di-acetoxi di-butoxi silane (DADBS) and Ti tetra-butoxide as precursors. By varying the deposition temperatures between 470 and 600 °C and the ratios between the Si and Ti precursors (Si/Ti) from 2 up to 16, films with different compositions and thicknesses were deposited. The coupled analysis of the results of different characterisation methods was used in order to determine the variation of the composition, the thickness and the density of the films. First EPMA measurements were performed at different acceleration voltages with a Cameca SX50 system. By analysing, with specific software, the evolution of the intensity ratio I_x/I_std versus the voltage, the composition and the mass thickness (product of density by the thickness) were determined. In order to measure independently the density, X-ray reflectometry experiments were performed. By analysing the value of the critical angle and the Kiessig fringes, the density and the thickness of the layers were determined. The refractive index and the thickness of the films were also measured by ellipsometry. By assuming a linear interpolation between the index value of the pure SiO₂ and TiO₂ films, the film composition was deduced from the refractive index value. XPS measurements were also performed in order to obtain an independent value of the composition. A good agreement between the ways to measure the density is obtained.     

基于Si掺杂Sb2Te3薄膜的相变存储器研究

采用磁控三靶(Si，Sb及Te)共溅射法制备了Si掺杂Sb₂Te₃薄膜，作为对比，制备了Ge₂Sb₂Te₅和Sb₂Te₃薄膜，并且采用微加工工艺制备了单元尺寸为10μm×10μm的存储器件原型来研究器件性能.研究表明，Si掺杂提高了Sb₂Te₃薄膜的晶化温度以及薄膜的晶态和非晶态电阻率，使得其非晶态与晶态电阻率之比达到10⁶，提高了器件的电阻开/关比；同Ge₂Sb₂Te₅薄膜相比，16at% Si掺杂Sb₂Te₃薄膜具有较低的熔点和更高的晶态电阻率，这有利于降低器件的RESET电流.研究还表明，采用16at% Si掺杂Sb₂Te₃薄膜作为存储介质的存储器器件原型具有记忆开关特性，可以在脉高3V、脉宽500ns的电脉冲下实现SET操作，在脉高4V、脉宽20ns的电脉冲下实现RESET操作，并能实现反复写/擦，而采用Ge₂Sb₂Te₅薄膜的相同结构的器件不能实现RESET操作. 关键词： 相变存储器 硫系化合物 2Te₃薄膜')" href="#">Si掺杂Sb₂Te₃薄膜 SET/RESET转变     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.