Preparation and tribological properties of DLC/Ti filmby pulsed laser arc deposition

This paper reports that DLC (diamond like carbon)/Ti and DLC films were prepared by using pulsed laser arc deposition. R-ray diffraction, Auger electron spectroscopy, Raman spectroscopy, atomic force microscopy, nanoindenter, spectroscopic ellipsometer, surface profiler and micro-tribometer were employed to study the structure and tribological properties of DLC/Ti and DLC films. The results show that DLC/Ti film, with $I(D)/I(G)$ 0.28 and corresponding to 76{\%} sp$^{3}$ content calculated by Raman spectroscopy, uniform chemical composition along depth direction, 98 at{\%} content of carbon, hardness 8.2 GPa and Young's modulus 110.5 GPa, compressive stress 6.579 GPa, thickness 46~nm, coefficient of friction 0.08, and critical load 95mN, exhibits excellent mechanical and tribological properties.     

Influence of sulfidation treatment on the structure and tribological properties of nitrogen-doped diamond-like carbon films

The nitrogen-doped diamond-like carbon (DLC) films were deposited on high speed steel (HSS) substrates in the direct current unbalanced magnetron sputtering system. Sulphurized layer was formed on the surface of DLC films by means of liquid sulfidation in the intermixture of urea and thiourea solution in order to improve the tribological properties of DLC films. The influence of sulfidation treatment on the structure and tribological properties of DLC films was investigated in this work. The structure and wear surface morphology of DLC films were analyzed by Raman spectroscopy, XPS and SEM, respectively. It reveals that the treated films are smooth and uniform; and sulfur atoms are bonded chemically. The treated films have broader distribution of Raman spectra in the range of 1000-1800 cm⁻¹ and higher I_D/I_G ratio than the untreated films as a result of the appearance of the crystalline graphite structure after the sulfidation treatment. It is showed that the sp² relative content increase in the treated films from the XPS measurement. The Raman results are consistent with the XPS results. The tribological properties of DLC films were investigated using a ball-on-disk rotating friction and wear tester under dry friction conditions. It is found that the sulfidation concentration plays an important part in the tribological properties of the treated DLC films. The results showed the treated films with low sulfidation concentration have a lower friction coefficient (0.1) than the treated films with high sulfidation concentration (0.26) and the untreated films (0.27) under the same friction testing conditions, which can be attributed to both the presence of sulfur-containing materials and the forming of the mechanical alloyed layer on the wear surface. Adding the dry nitrogen to the sliding surface in the testing system helps the friction coefficient of the treated films with low sulfidation concentration to decrease to 0.04 further in this work. On the basis of the experimental results, it is indicated that the liquid sulfidation technique, which is low-cost, non-polluting and convenience, would be an appropriate method for the surface treatment of DLC films.     

Synthesis of carbon nanotubes on diamond-like carbon by the hot filament plasma-enhanced chemical vapor deposition method

Carbon nanotubes (CNTs) have attracted considerable attention as possible routes to device miniaturization due to their excellent mechanical, thermal, and electronic properties. These properties show great potential for devices such as field emission displays, transistors, and sensors. The growth of CNTs can be explained by interaction between small carbon patches and the metal catalyst. The metals such as nickel, cobalt, gold, iron, platinum, and palladium are used as the catalysts for the CNT growth. In this study, diamond-like carbon (DLC) was used for CNT growth as a nonmetallic catalyst layer. DLC films were deposited by a radio frequency (RF) plasma-enhanced chemical vapor deposition (RF-PECVD) method with a mixture of methane and hydrogen gases. CNTs were synthesized by a hot filament plasma-enhanced chemical vapor deposition (HF-PECVD) method with ammonia (NH₃) as a pretreatment gas and acetylene (C₂H₂) as a carbon source gas. The grown CNTs and the pretreated DLC films were observed using field emission scanning electron microscopy (FE-SEM) measurement, and the structure of the grown CNTs was analyzed by high resolution transmission scanning electron microscopy (HR-TEM). Also, using energy dispersive spectroscopy (EDS) measurement, we confirmed that only the carbon component remained on the substrate.     

Control of tribological properties of diamond-like carbon films with femtosecond-laser-induced nanostructuring

This paper reports tribological properties of diamond-like carbon (DLC) films nanostructured by femtosecond (fs) laser ablation. The nanostructure was formed in an area of more than 15 mm × 15 mm on the DLC surface, using a precise target-scan system developed for the fs-laser processing. The frictional properties of the DLC film are greatly improved by coating a MoS₂ layer on the nanostructured surface, while the friction coefficient can be increased by surface texturing of the nanostructured zone in a net-like patterning. The results demonstrate that the tribological properties of a DLC surface can be controlled using fs-laser-induced nanostructuring.     

Study on tribological behavior and cutting performance of CVD diamond and DLC films on Co-cemented tungsten carbide substrates

The tribological behaviors of diamond and diamond-like carbon (DLC) films play a major role on their machining and mechanical applications. In this study, diamond and diamond-like carbon (DLC) films are deposited on the cobalt cemented tungsten carbide (WC-Co) substrate respectively adopting the hot filament chemical vapor deposition (HFCVD) technique and the vacuum arc discharge with a graphite cathode, and their friction properties are evaluated on a reciprocating ball-on-plate tribometer with counterfaces of silicon nitride (Si₃N₄) ceramic, cemented tungsten carbide (WC) and ball-bearing steel materials, under the ambient air without lubricating condition. Moreover, to evaluate their cutting performance, comparative turning tests are conducted using the uncoated WC-Co and as-fabricated CVD diamond and DLC coated inserts, with glass fiber reinforced plastics (GFRP) composite materials as the workpiece. The as-deposited HFCVD diamond and DLC films are characterized with energy-dispersive X-ray spectroscopy (EDX), scanning electron microscope (SEM), X-ray diffraction spectroscopy (XRD), Raman spectroscopy and 3D surface topography based on white-light interferometry. Furthermore, Rocwell C indentation tests are conducted to evaluate the adhesion of HFCVD diamond and DLC films grown onto WC-Co substrates. SEM and 3D surface topography based on white-light interferometry are also used to investigate the worn region on the surfaces of diamond and DLC films. The friction tests suggest that the obtained friction coefficient curves that of various contacts exhibit similar evolution tendency. For a given counterface, DLC films present lower stable friction coefficients than HFCVD diamond films under the same sliding conditions. The cutting tests results indicate that flank wear of the HFCVD diamond coated insert is lower than that of DLC coated insert before diamond films peeling off.     

Tribological behavior of diamond-like carbon film with different tribo-pairs: A size effect study

A friction force microscope (FFM) with different probes and a ball-on-disk (BOD) tribo-meter were used to investigate the tribological properties of diamond-like carbon (DLC) films. DLC films were prepared by chemical vapor deposition (CVD) method by altering the deposition parameters, and their morphologies and structural information were examined with an atomic force microscope (AFM) and the Raman spectrum. The wear traces of the DLC films after frictional tests were analyzed by an optical microscope. It is found that surface roughness and adhesion play important roles in characterizing the tribological properties of DLC films using FFM. Moreover, the debris accumulation is another significant factor affecting the frictional behavior of DLC films, especially for the sharp tip. The difference in coefficients of friction (COFs) obtained by the BOD method among different DLC films under water lubrication is much smaller than the case without water lubrication. The variation trends in COF for the flat tip and the BOD test are similar in comparison with the result obtained with the sharp tip. The wear traces after frictional tests suggest that DLC films under water lubrication are prone to be damaged more readily.     

The microstructure, mechanical and friction properties of protective diamond like carbon films on magnesium alloy

Protective hard coatings deposited on magnesium alloys are believed to be effective for overcoming their poor wear properties. In this work, diamond-like carbon (DLC) films as hard protective films were deposited on AZ91 magnesium alloy by arc ion plating under negative pulse bias voltages ranging from 0 to −200 V. The microstructure, composition and mechanical properties of the DLC films were analyzed by scanning electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and nanoindentation. The tribological behavior of uncoated and coated AZ91 magnesium alloy was investigated using a ball-on-disk tribotester. The results show that the negative pulse bias voltage used for film deposition has a significant effect on the sp³ carbon content and mechanical properties of the deposited DLC films. A maximum sp³ content of 33.3% was obtained at −100 V, resulting in a high hardness of 28.6 GPa and elastic modulus of 300.0 GPa. The DLC films showed very good adhesion to the AZ91 magnesium alloy with no observable cracks and delamination even during friction testing. Compared with the uncoated AZ91 magnesium alloy, the magnesium alloy coated with DLC films exhibits a low friction coefficient and a narrow, shallow wear track. The wear resistance and surface hardness of AZ91 magnesium alloy can be significantly improved by coating a layer of DLC protective film due to its high hardness and low friction coefficient.     

类金刚石和碳氮薄膜的电化学沉积及其场发射性能研究

利用电化学方法在室温下成功地沉积了类金刚石(DLC)薄膜和非晶CN_x薄膜，并 对制备条件进行了讨论.通过扫描电子显微镜、傅里叶变换红外光谱技术，分析了薄膜的表面形貌和化学结合状态.场发射测量结果表明：DLC膜和非晶CN_x的开启场分别为88和 10V/μm；并且在23V/μm的电场下，DLC膜和非晶CN_x膜的发射电流密度分别达到10 和037mA/cm². 关键词： 电化学沉积 类金刚石薄膜 x薄膜')" href="#">CN_x薄膜 场致电子发射     

Tribological effect of iron oxide residual on the DLC film surface under seawater and saline solutions

This paper discusses the seawater and saline solutions effects on the tribological behavior of diamond-like carbon (DLC) films. The adsorption of Fe on DLC surface is one of the mechanisms that is believed to be the cause of the decrease in dispersive component of the surface energy and increase of the I_D/I_G ratio leading to low friction coefficient and wear rate under corrosive environments. Tribological behaviors DLC films were experimentally evaluated under corrosive environments by using steel ball and DLC coated steel flat under rotational sliding conditions. The DLC films were prepared on 440 stainless steel disks by DC-pulsed PECVD using methane as a precursor gas. Two different set of tribological system was assembled, one when the liquids and the pairs were put inside of a stainless steel vessel and others inside of a PTFE. Every tribological test was performed under 10 N normal load120 mms^? 1 of sliding speed. The friction coefficients were evaluated during 1000 cycles.     

Structure and properties of DLC–MoS2 thin films synthesized by BTIBD method

Diamond-like carbon (DLC)–MoS₂ composite thin films were synthesized using a biased target ion beam deposition (BTIBD) technique in which MoS₂ was produced by sputtering a MoS₂ target using Ar ion beams while DLC was deposited by ion beam deposition with CH₄ gas as carbon source. The structure and properties of the synthesized films were characterized by X-ray diffraction, X-ray absorption near edge structure (XANES), Raman spectroscopy, nanoindentation, ball-on-disk testing, and corrosion testing. The effect of MoS₂ target bias voltage, ranging from −200 to −800 V, on the structure and properties of the DLC–MoS₂ films was further investigated. The results showed that the hardness decreases from 9.1 GPa to 7 GPa, the Young?s modulus decreases from 100 GPa to 78 GPa, the coefficient of friction (COF) increases from 0.02 to 0.17, and the specific wear rate coefficient (k) increases from 5×10⁻⁷ to 5×10⁻⁶ mm³ N⁻¹ m⁻¹, with increasing the biasing voltage from 200 V to 800 V. Also, the corrosion resistance of the DLC–MoS₂ films decreased with the raise of biasing voltage. Comparing with the pure DLC and pure MoS₂ films, the DLC–MoS₂ films deposited at low biasing voltages showed better tribological properties including lower COF and k in ambient air environment.     

The protective properties of ultra-thin diamond like carbon films for high density magnetic storage devices

With the increase of magnetic storage density, the thickness of the protective diamond like carbon (DLC) film on the surfaces of head and disk is required as thin as possible. In this paper, the structure, mechanical properties and corrosion and oxidation resistance of ultra-thin DLC films are investigated. The ultra-thin DLC films were deposited by using filtered cathodic vacuum arc (FCVA) technique. The exact thickness of the ultra-thin DLC film was determined by high resolution transmission electron microscope (HRTEM). Raman analysis indicates that the ultra-thin DLC film presents ta-C structure with high sp³ fraction. In the wear test, a diamond tip was used to simulate a single-asperity contact with the film surface and the wear marks were produced on the film surface. The wear depths decrease with film thickness increasing. If the film thickness was 1.4 nm or above, the wear depth was much lower than that of Si substrate. This indicates that the ultra-thin DLC film with thickness of 1.4 nm shows excellent wear resistance. Corrosion tests in water and oxidation tests in air were carried out to investigate the diffusion barrier effect of the ultra-thin DLC films. The results show that the DLC film with thickness of 1.4 nm provides adequate coverage on the substrate and has good corrosion and oxidation resistance.     

Improving the tribological performances of graphite-like carbon films on Si3N4 and SiC by using Si interlayers

Si interlayers were used to obtain the excellent tribological performances of graphite-like carbon (GLC) film on silicon nitride (Si₃N₄) and silicon carbide (SiC). The microstructure and mechanical characteristics of the as-prepared GLC films with Si interlayers were investigated by scanning electron microscopy, Raman spectroscopy, nanoindention and scratch test. The tribological behaviors of GLC-coated and uncoated Si₃N₄ and SiC were comparatively studied by a ball-on-disc tribo-meter in both dry and water environments. Results showed that the Si interlayers were dense and bonded well with both the substrates and GLC layers. The as-prepared GLC films exhibited excellent tribological performances in both dry and water environments. More importantly, the stably mild wear without any delamination was obtained in water by using Si interlayer. The mechanisms of friction reduction and anti-wear performances of GLC films on the two ceramics with Si interlayers under different environmental conditions were discussed, as well as the corresponding models were deduced.     

铜上采用过渡层沉积类金刚石薄膜的研究

将等离子增强非平衡磁控溅射物理气相沉积(PEUMS-PVD)和电子回旋共振-微波等离子体增强化学气相沉积(MW-ECRPECVD)技术相结合，通过制备不同的过渡层，在铜基上成功地制备了类金刚石膜.拉曼光谱分析表明，所制备的碳膜具有典型的类金刚石结构特征.检测结果表明，随着沉积偏压的增大，D峰和G峰均向高波数漂移，I_D/I_G值增大，表面粗糙度减小，而平均硬度和弹性模量呈先增大后减小的趋势. 关键词： 铜基体 类金刚石膜 过渡层 拉曼光谱     

Structure and tribological properties of amorphous carbon films deposited by electrochemical method on GCr15 steel substrate

Amorphous carbon films were deposited on GCr15 steel substrates by electrolysis of methanol, dimethylsulfoxide (DMSO) and the methanol-DMSO intermixture electrolytes, respectively, under high voltage and low temperature conditions. The microstructure and wear morphology of the deposited films were analyzed using X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM) combined with energy dispersive X-ray fluorescence spectrometer (EDX), respectively. The tribological properties of the films were evaluated using a ball-on-disk rotating friction tester under dry friction condition. The results show that the films deposited by electrodeposition technique on GCr15 steel substrates are amorphous carbon films. It is also found that the electrolytes have an obvious influence on the tribological properties of the deposited films with the electrodeposition method. The tribological properties of the films deposited with the intermixture electrolyte are better than those of the films deposited by other pure electrolytes. The related growth mechanism of the films in the liquid-phase electrodeposition is discussed as well in this study. Via the reaction of the CH₃ groups with each other to form carbon network and reaction of the CH₃ and SO²⁺ groups to achieve the doping of sulfur atom in the carbon network, respectively, in other words, amorphous carbon films can be obtained on GCr15 steel substrates by electrodeposition technique.     

Structural and tribological properties of nitrogen doped amorphous carbon thin films synthesized by CFUBM sputtering method for protective coatings

Nitrogen doped amorphous carbon (a-C:N) films are a material that may successfully compete with DLC coatings, which have high hardness, high wear resistance, and a low friction coefficient. The a-C:N films were prepared on silicon substrate by a closed-field unbalanced magnetron sputtering method with a graphite target and using the Ar/N₂ mixture gases. And, we investigated the effects of various DC bias voltages from 0 to −300 V on the structural and tribological properties of the a-C:N films. This study was focused on improving physical properties of the a-C:N film by controlling process parameters like negative substrate DC bias voltage. The maximum hardness of the a-C:N film was 23 GPa, the friction coefficient was 0.08, and the critical load was 25 N on a Si wafer. Consequently, the structural and tribological properties of the a-C:N film showed a clear dependence on the energy of ions bombardment and the density of the sputtering and the reaction gases during film growth.     

Mechanical properties and platelet adhesion behavior of diamond-like carbon films synthesized by pulsed vacuum arc plasma deposition

Diamond-like carbon (DLC) is an attractive biomedical material due to its high inertness and excellent mechanical properties. In this study, DLC films were fabricated on Ti6Al4V and Si(1 0 0) substrates at room temperature by pulsed vacuum arc plasma deposition. By changing the argon flow from 0 to 13 sccm during deposition, the effects of argon flow on the characteristics of the DLC films were systematically examined to correlate to the blood compatibility. The microstructure and mechanical properties of the films were investigated using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) surface analysis, a nano-indenter and pin-on-disk tribometer. The blood compatibility of the films was evaluated using in vitro platelet adhesion investigation, and the quantity and morphology of the adherent platelets was investigated employing optical microscopy and scanning electron microscopy.The Raman spectroscopy results showed a decreasing sp³ fraction (an increasing trend in I_D/I_G ratio) with increasing argon flow from 0 to 13 sccm. The sp³:sp² ratio of the films was evaluated from the deconvoluted XPS spectra. We found that the sp³ fraction decreased as the argon flow was increased from 0 to 13 sccm, which is consistent with the results of the Raman spectra. The mechanical properties results confirmed the decreasing sp³ content with increasing argon flow. The Raman D-band to G-band intensity ratio increased and the platelet adhesion behavior became better with higher flow. This implies that the blood compatibility of the DLC films is influenced by the sp³:sp² ratio. DLC films deposited on titanium alloys have high wear resistance, low friction and good adhesion.     

Influence of high temperature annealing on the structure, hardness and tribological properties of diamond-like carbon and TiAlSiCN nanocomposite coatings

Diamond-like carbon (DLC) and TiAlSiCN nanocomposite coatings were synthesized and annealed at different temperatures in a vacuum environment. The microstructure, hardness and tribological properties of as-deposited and annealed DLC-TiAlSiCN nanocomposite coatings were characterized by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Raman spectroscopy, nano-indentation and friction tests. The TEM results reveal that the as-deposited DLC-TiAlSiCN coating has a unique nanocomposite structure consisting of TiCN nanocrystals embedded in an amorphous matrix consisting of a-Si₃N₄, a-SiC, a-CN and DLC, and the structure changed little after annealing at 800 °C. However, XPS and Raman results show that an obvious graphitization of the DLC phase occurred during the annealing process and it worsened with annealing temperature. Because of the graphitization, the hardness of the DLC-TiAlSiCN coating after annealing at 800 °C decreased from 45 to 36 GPa. In addition, the DLC-TiAlSiCN coating after annealing at 800 °C has a similar friction coefficient to the as-deposited coating.     

Influence of crystalline diamond nanoparticles on diamond-like carbon friction behavior

Crystalline diamond (CD) particles have been incorporated in diamond-like carbon (DLC) film structure in order to improve DLC electrochemical corrosion resistance. This paper shows the investigation of CD-DLC friction behavior according to the CD average sizes and concentration. The films were growth over 304 stainless steel using plasma enhanced chemical vapor deposition. The response surface methodology was used to develop a mathematical modeling of friction for these films, using the experimental results, in order to identify parameters that control friction and construct tribological maps according to the CD average sizes. The presence of bigger CD particles (250 and 500 nm) increased the film roughness. Films with CD particles of 4 nm presented the most homogeneous friction map, with minor variation in friction coefficient with the increase/decrease of load and sliding speed even when the CD concentration increase. This result suggests that in CD-DLC films containing CD particles of 4 nm average size, the nanoparticles are better incorporated in DLC structure due to its average size (4 nm) that is near than DLC grain size and could occupy the nanospaces between DLC grains.     

Characterization of the bonding structure of nanocrystalline diamond and amorphous carbon films prepared by plasma assisted techniques

Thin nanocrystalline diamond/amorphous carbon (NCD/a-C) composite films and amorphous diamond-like carbon (DLC) films were prepared by three methods: microwave plasma chemical vapour deposition (MWCVD) from methane/nitrogen mixtures (NCD/a-C), RF magnetron sputtering of a pure graphite target in argon/methane ambients, and pulsed laser deposition (PLD) in vacuum or argon atmosphere (DLC). The films prepared by the three techniques were comprehensively characterized with respect to their bonding structure by Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). PACS 81.05.Uw; 82.80.Pv     

Evaluation of bacterial adhesion on Si-doped diamond-like carbon films

Diamond-like carbon (DLC) films as biomaterial for medical devices have been attracting great interest due to their excellent properties such as hardness, low friction and chemical inertness. It has been demonstrated that the properties of DLC films can be further improved by the addition of silicon into DLC films, such as thermal stability, compressive stress, etc. However no research work on anti-bacterial properties of silicon-doped diamond-like carbon films has been reported. In this paper the surface physical and chemical properties of Si-doped diamond-like carbon films with various Si contents on 316 stainless steel substrate prepared by a magnetron sputtering technique were investigated, including surface topography, surface chemistry, the sp³/sp² ratio, contact angle, surface free energy, etc. Bacterial adhesion to Si-doped DLC films was evaluated with Pseudomonas aeruginosa, Staphylococcus epidermidis and Staphylococcus aureus which frequently cause medical device-associated infections. The experimental results showed that bacterial adhesion decreased with increasing the silicon content in the films. All the Si-doped DLC films performed much better than stainless steel 316L on reducing bacterial attachment.