A novel method for immobilization of Co tetraphenylporphyrins on P(4VP-co-St)/SiO2: Efficient catalysts for aerobic oxidation of ethylbenzenes

In this paper, poly(4vinylpyridine-co-styrene) (P(4VP-co-St)) was grafted on silica gel particles in the manner of “grafting from”, and the grafting particle P(4VP-co-St)/SiO₂ was gained. The grafting particle P(4VP-co-St)/SiO₂ is a novel kind of supports for immobilizing metalloporphyrin catalysts. Then, the immobilization of cobalt tetraphenylporphyrin (CoTPP) on the supports P(4VP-co-St)/SiO₂ was carried out via the axial coordination reaction between CoTPP and the pyridine groups of the grafted P(4VP-co-St), resulting in the heterogenised catalysts CoTPP-P(4VP-co-St)/SiO₂. The synthesized catalysts were characterized by FTIR and the axial coordination process between CoTPP and the grafted P(4VP-co-St) was confirmed by UV-vis. The effects of various factors on the immobilization reaction of CoTPP were studied in detail. Finally, the catalytic performance of CoTPP-P(4VP-co-St)/SiO₂ in the catalytic oxidation process of ethyl benzene was investigated. The experimental results show that the axial coordination reaction is a very easy and novel method for favorably immobilizing CoTPP onto the P(4VP-co-St)/SiO₂ surfaces. During the immobilization process of CoTPP on P(4VP-co-St)/SiO₂, the most bonding amount of CoTPP (0.19 g/g) is obtained under the lower temperature (5 °C) and the higher concentration of CoTPP(6.0 mg/ml) lasting 4 h. Moreover, the supported catalyst CoTPP-P(4VP-co-St)/SiO₂ can effectively activate the dioxygen, and obviously catalyze the transform of ethylbenzene into acetophenone. So it exhibits the fine catalytic activity.     

Formation of zinc sulfide nanoparticles in HMTA matrix

A hydrothermal method has been optimized for the synthesis of ZnS nanoparticles. The nanoparticles were stabilized using Hexamethylenetetramine (HMTA) as surfactant in aqueous solution. The self-assembling of the surfactant molecules in the water solution forms a unique architecture that can be adopted as the reaction template for the formation of nanomaterials. The average grain size of the nanoparticles calculated from the XRD pattern was of the order of 2 nm which exhibits cubic zinc-blende structure. TEM results showed that the synthesized nanoparticles were uniformly dispersed in the HMTA matrix without aggregation. The spectroscopic results revealed that the synthesized ZnS nanoparticles exhibits strong quantum confinement effect as the optical band gap energy increased significantly compared to the bulk ZnS material. Formation of HMTA capped ZnS nanoparticles were confirmed by FTIR studies. The PL spectra exhibit a strong green emission peak around 502 nm attributed to some self-activated defect centers related to Zn-vacancies.     

A facile method for grafting of bisphenol A imprinted polymer shells onto poly(divinylbenzene) microspheres through precipitation polymerization

Core-shell structured polymers are usually prepared by “grafting to” or “grafting from” techniques, wherein polymer supports were first modified by vinyl bonds or initiators. Success can be immediate, but more often a learning curve needs to be traversed. In this paper, direct grafting bisphenol A imprinted polymer onto poly(divinylbenzene) microspheres through precipitation polymerization is introduced. The obtained microspheres were characterized by SEM, TEM, FTIR and BET. Firstly, mono-disperse poly(divinylbenzene) microspheres of 3 μm in size were prepared by precipitation polymerization. The solvent for grafting was then optimized and it was found that the mixtures of toluene and acetonitrile (30/70, v/v) were ideal choice from the image and structure analysis of the shells. Shells of different thickness (270-840 nm), depending on the concentrations of monomers in the precursor, were then directly grafted to the microspheres by a reactive, entropic capture mechanism. The recognition ability of the microspheres was evaluated by solid-phase extraction and clear selectivity showed toward bisphenol A. The leak of bisphenol A was not found after extraction and thus these core-shell structured imprinted polymers are believed to have potential applications in trace analysis area.     

A versatile method for the preparation of end-functional polymers onto SiO2 nanoparticles by a combination of surface-initiated ATRP and Huisgen [3 + 2] cycloaddition

A versatile method was developed for the chain-end functionalization of the grafted polymer chains for surface modification of nanoparticles with functionalized groups through a combination of surface-initiated atom-transfer radical polymerization (ATRP) and Huisgen [3 + 2] cycloaddition. First, the surface of SiO₂ nanoparticles was modified with poly(methyl methacrylate) (PMMA) brushes via the “grafting from” approach. The terminal bromides of PMMA-grafted SiO₂ nanoparticles were then transformed into an azide function by nucleophilic substitution. These azido-terminated PMMA brushes on the nanoparticle surface were reacted with alkyne-terminated functional end group via Huisgen [3 + 2] cycloaddition. FTIR and ¹H NMR spectra indicated quantitative transformation of the chain ends of PMMA brushes onto SiO₂ nanoparticles into the desired functional group. And, the dispersibility of the end-functional polymer-grafted SiO₂ nanoparticles was investigated with a transmission electron microscope (TEM).     

Synthesis of nanometer Bi2WO6 synthesized by sol-gel method and its visible-light photocatalytic activity for degradation of 4BS

Nanometer Bi₂WO₆ catalyst with visible-light responsive was prepared by a sol-gel method in the presence of EDTA. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectrum, Fourier transform infrared (FTIR) spectrum, Brunauer-Emmet-Teller (BET). The UV-vis diffuse reflectance spectrum of the as-prepared sample shows a markedly blue-shift as compared to that of the sample obtained by a solid-state reaction. The as-prepared samples exhibited higher activities than that synthesized by the solid-state reaction for 4BS photodegradation under visible-light irradiation (λ>400 nm) and the sample prepared at 450 °C exhibited the highest photocatalytic activity.     

Thermal stability of alkoxy monolayers grafted on Si(1 1 1)

Direct grafting of organic monolayers on Si is of prime interest in order to give specific properties to a silicon surface. However, for microelectronics applications, this possibility is hampered by the limited stability of the grafted layers. It has been previously established that alkyl layers attached to Si surfaces through Si-C bonds become unstable at 250-300 °C, by desorption of alkenes. Changing the nature of the bonding to the surface might allow one to circumvent this desorption pathway and increase the layer stability. In our work, decanol and decyl aldehyde are reacted with the Si(1 1 1)-H surface at ∼100 °C during 20 h in order to obtain alkoxy monolayers. FTIR measurements performed in ATR geometry show that the grafted molecule surface coverage is on the order of 33% after reaction with decanol and 50% after reaction with decyl aldehyde. Characterization by AFM essentially reveals that the morphology of the grafted surfaces is unaffected as compared to that of Si-H surfaces. However, the edges of the terraces at alcohol-grafted surfaces exhibit some pitting, probably due to the presence of water in the grafting liquid. Thermal stability studies show that alkoxy chains progressively disappear from the Si surface between 200 and 400 °C. From the CH₂/CH₃ ratio in the CH region (2760-3070 cm⁻¹), it appears that the chains undergo progressive dissociation by C-C bond breaking before their complete disappearance from the surface. Therefore, the thermal behaviour of alkoxy monolayers appears quite distinct from that of alkyl monolayers that tend to leave the surface in a much narrower temperature range (250-350 °C), essentially via breaking of the Si-C bonds.     

Synthesis and characterization of magnetic Fe/CNTs composites with controllable Fe nanoparticle concentration

Fe/CNTs composites, with different concentrations of Fe nanoparticles (NPs) on carbon nanotube (CNT) surfaces, were successfully fabricated via a facile solvothermal method. The lengths of CNTs are up to 10 μm and the mean diameter of the Fe nanoparticles is about 25 nm. The structures, composition and magnetic properties of the Fe/CNTs were characterized by XRD, FTIR, FE-SEM, TEM and PPMS. We found that the concentrations of Fe nanoparticles depositing on the CNTs could be controlled by adjusting the initial mass ratio of ferrocene to CNTs. The Fe/CNTs composites display good ferromagnetic properties at room temperature, with a saturation magnetization of 125 emu/g-Fe and a coercivity of 276 Oe. The Curie temperature of the sample is about 1038 K, slightly lower than that (1043 K) of the bulk iron.     

Femtosecond laser synthesized nanohybrid materials for bioapplications

Hybrid nanomaterials were synthesized by adopting femtosecond laser ablation of a ZnO target in pure ethanol. Dye molecules were grafted onto the ZnO nanoparticles by mixing colloidal ZnO-ethanol solution prepared by laser ablation to Tetramethylrhodamine B isothiocyante, or to Rhodamine B solutions. Strongly facetted nanohybrid particles were observed with an average size of 15 nm, by HRTEM measurements. From photoluminescence spectroscopy of the nanohybrids after single and multiphoton excitations, we observed energy transfer from the ZnO nanoparticles towards the attached dye molecules. Moreover, IR excitation spectra of the hybrid nanomaterials reveal the emission of the grafted dye via two photon absorption of the ZnO.     

ZnO nanoparticles obtained by mechanochemical technique and the optical properties

Crystalline ZnO nanoparticles were synthesized by mechanochemical method. Mechanochemical processing involves the mechanical activation of solid-state displacement reactions at low temperatures in a ball mill. Statistical design was used to investigate the effect of main parameters (i.e. time, milling rate and calcination temperature) on ZnO crystallite size and morphology. After annealing at 400 °C in air, zinc oxide (ZnO) nanoparticles were obtained. The milled powders are analyzed by X-ray diffraction (XRD), TG/DTA and transmission electron microscope (TEM).The crystallite size of ZnO samples calculated from XRD is consistent with the TEM images and estimated to be less than 20 nm. The optical properties of the samples were studied by UV-vis spectrophotometer.     

Studies on surface graft polymerization of acrylic acid onto PTFE film by remote argon plasma initiation

The graft polymerization of acrylic acid (AAc) was carried out onto poly(tetrafluoroethylene) (PTFE) films that had been pretreated with remote argon plasma and subsequently exposed to oxygen to create peroxides. Peroxides are known to be the species responsible for initiating the graft polymerization when PTFE reacts with AAc. We chose different parameters of remote plasma treatment to get the optimum condition for introducing maximum peroxides (2.87 × 10⁻¹¹ mol/cm²) on the surface. The influence of grafted reaction conditions on the grafting degree was investigated. The maximum grafting degree was 25.2 μg/cm². The surface microstructures and compositions of the AAc grafted PTFE film were characterized with the water contact angle meter, Fourier-transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Contact angle measurements revealed that the water contact angle decreased from 108° to 41° and the surface free energy increased from 22.1 × 10⁻⁵ to 62.1 × 10⁻⁵ N cm⁻¹ by the grafting of the AAc chains. The hydrophilicity of the PTFE film surface was greatly enhanced. The time-dependent activity of the grafted surface was better than that of the plasma treated film.     

Investigation of monolayer dispersion of benzoic acid supported on the surface of H-titanate nanotubes

Benzoic acid (BA) can disperse spontaneously onto the surface of H-titanate nanotubes (HTNTs) in a sub-monolayer state by heating mechanical mixtures method. The structure of BA-HTNTs system has been characterized by X-ray diffraction (XRD), thermogravimetric (TG), Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) in detail. The results show that the H-bond association structure among BA molecules collapses and the carboxyl groups react with the surface hydroxyl group of HTNTs to form a salt-like structure on the surface after dispersion. The monolayer dispersion capacity determined by XRD is ca. 0.305 g BA g⁻¹ HTNTs, which is lower than the utmost monolayer dispersion capacity 0.550 g BA g⁻¹ HTNTs calculated according to a model that the benzene ring in BA molecules is perpendicular to the surface of HTNTs. At the same time, the dispersion capacity is also measurement by the fit of C 1s XPS peak at various BA loadings at first time.     

Construction of a novel multilayer system and its use for oriented immobilization of immunoglobulin G

In this contribution, we have developed a novel multilayer system composed of 3-aminopropyltrimethoxysilane (APTS), biotin, streptavidin and biotinylated protein A on the Si(1 0 0) surface to immobilize of immunoglobulin G (IgG) molecule. Existence of the first APTS layer covalently attached on the silicon surface was revealed by X-ray photoelectron spectroscopy (XPS). Average thickness of the APTS overlayer was estimated by spectroscopic ellipsometry analysis as 6.3 nm. The surface topography of the APTS overlayer observed by atomic force microscopy is found to be considerably different from the hydroxylated silicon surface and many additional islands of various heights are observed over the substrate. The water contact angle of the APTS overlayer was determined as 38°, whereas that of the hydroxylated silicon was obtained as 6°, indicating the difference in their surface hydrophobicility. Furthermore, multilayer studies on the APTS overlayer were carried out by using biotin, streptavidin and fluorescein-labeled biotinylated protein-A molecules. The fluorescence images obtained by fluorescence microscopy showed the formation of the multilayer on the Si(1 0 0) surface. The results indicated that the protein A-terminated surfaces can be used to immobilize IgG molecules in a highly oriented manner and maintain IgG molecular functional configuration on the multilayer system.     

Synthesis and characterization of Cr doped CdS nanoparticles stabilized with polyvinylpyrrolidone

Undoped and Cr (2 and 4 at.%) doped CdS nanoparticles were synthesized in aqueous solution by simple chemical co-precipitation method using polyvinylpyrrolidone (PVP) as stabilizer. The prepared nanoparticles were examined using X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDAX), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and Fourier transform infrared spectroscopy (FTIR). XRD pattern of the nanoparticles showed cubic zincblende phase with the particle size of the order of 3-4 nm, which was in good agreement with the results obtained from TEM studies. The EDAX analysis confirmed that Cd, Cr and S elements were present in the samples and the variations between the target and actual compositions were microscopic. UV-vis DRS spectra of the samples exhibited decrease in the band gap which further attests the incorporation of Cr into CdS nanoparticles. FTIR studies revealed that the undoped as well as Cr doped CdS nanoparticles were capped by polyvinylpyrrolidone.     

Facile synthesis and electrochemical properties of hierarchical MnO2 submicrospheres and LiMn2O4 microspheres

Hierarchical MnO₂ submicrospheres have been successfully synthesized by a wet chemical method. The as-prepared products were characterized by means of XRD, SEM, FTIR, TG, and TEM. With the as-prepared MnO₂ submicrospheres as precursors, LiMn₂O₄ microspheres were conveniently prepared by a simple solid-state reaction between MnO₂ and LiOH at a temperature as low as 600 °C. Electrochemical properties of the as-prepared MnO₂ submicrospheres and LiMn₂O₄ microspheres as cathode materials in lithium ion cells were investigated by galvanostatic charge/discharge tests.     

Poly(N-vinyl carbazole)-grafted multiwalled carbon nanotubes: Synthesis via direct free radical reaction and optical limiting properties

In this work, samples of poly(N-vinyl carbazole) (PVK)-grafted multiwalled carbon nanotubes (MWCNTs) were synthesized via free radical reaction. The ready-made PVK was allowed to react directly with MWCNTs at 70 °C in the presence of azo-bis-isobutyronitrile (AIBN). The purified deep grey products, which can dissolve in common organic solvents such as chloroform and 1,2-dichlorobenzene (DCB), were then characterized by FTIR spectra, TEM, TGA, elemental analysis, XPS, UV-vis spectra and Raman spectra. It was confirmed that PVK chains were grafted onto the surface of the carbon nanotubes (CNTs). The optical limiting properties of these PVK-grafted MWCNTs samples were investigated by open-aperture z-scan method. All of the samples of PVK-modified carbon nanotubes in chloroform showed optical limiting behavior better than that of C₆₀ in toluene.     

A new synthetic pathway of Sr2CeO4 phosphor and its characterization

A blue-white emitting Sr₂CeO₄ phosphor was synthesized via a simple sol-gel poly vinyl alcohol (PVA)-complexing process using strontium nitrate and cerium nitrate as raw materials. The samples were characterized by TG/DTA, XRD, FTIR, SEM and photoluminescence spectroscopy. The X-ray diffraction study confirms the structure of the system to be orthorhombic. The emission spectra when excited at 267 nm peaks at ∼470 nm. The emission band is assigned to the energy transfer between the molecular orbital of the ligand and charge transfer state of the Ce⁴⁺ ion. The Commission International de l'Eclairage (CIE) co-ordinates for the Sr₂CeO₄ sample were also calculated.     

Preparation and characterization of Co–Pt bimetallic magnetic nanoparticles

CoPt₃ nanoparticles are synthesized by a two-stage route using NaBH₄ as a reductant. The nanoparticles are characterized by thermogravimetry (TG) and differential thermal analysis (DTA), Fourier transform infrared (FT-IR), transmission electron microscopy (TEM) and X-ray diffraction (XRD). Structural and spectroscopic studies show that the nanoparticles adopt a face-centered-cubic (FCC) crystalline structure with an average particle size of 2.6 nm. SQUID studies reveal that as-synthesized nanoparticles are superparamagnetic at room temperature and ferromagnetic at 1.85 K with coercivity of 980 Oe. Annealing of the samples at 500 °C causes an increase of particle size and a decrease of coercivity.     

Stability and characterization of mesoporous molecular sieve using natural clay as a raw material obtained by microwave irradiation

Mesoporous molecular sieve was synthesized via microwave irradiation method, and using natural clay, sodium silicate and aluminum chloride as raw materials and cetyl trimethyl ammonium bromide (CTAB) as a template agent under alkaline condition. The samples were characterized by various analytic and spectroscopic tools such as XRD, FT-IR, TEM, TG-DSC and N₂ physical adsorption, respectively. The results show that the synthesized sample has typical mesoporous structure and exhibits good mesoporous ordering. On the other hand, the as synthesized sample after calcination at 550 °C for 10 h has a surface area of 576.0 m²/g and an average pore size of 4.83 nm. Furthermore, the synthesized mesoporous molecular sieve still exhibits good mesoporous ordering after calcination at 750 °C for 3 h or hydrothermal treatment at 100 °C for 10 days.     

Structural, optical and dielectric studies of glycinium trifluoroacetate single crystal

An organic material glycinium trifluoroacetate (GTFA) has been re-synthesized and large single crystals have been grown by solution technique. Complete structure of GTFA has been redetermined from single crystal XRD data. FTIR confirmed the presence of various functional groups. Melting point (152.44 °C), thermal stability and specific heat were studied from TG/ DTA and DSC. In UV absorption spectra, a lower cutoff value as 220 nm and a wide band gap as 4.86 eV for GTFA were observed. The dielectric studies, dielectric constant and loss were measured at different temperatures (30-90 °C) in the frequency range 100 Hz-2 MHz.     

Structural characterization and magnetic properties of superparamagnetic zinc ferrite nanoparticles synthesized by the coprecipitation method

Single phase zinc ferrite (ZnFe₂O₄) nanoparticles have been prepared by the coprecipitation method without any subsequent calcination. The effects of precipitation temperature in the range 20–80 °C on the structural and the magnetic properties of zinc ferrite nanoparticles were investigated. The crystallite size, microstructure and magnetic properties of the prepared nanoparticles were studied using X-ray diffraction (XRD), Fourier transmission infrared spectrum, transmission electron microscope (TEM), energy dispersive X-ray spectrometer and vibrating sample magnetometer. The XRD results showed that the coprecipitated nanoparticles were single phase zinc ferrite with mixture of normal and inverse spinel structures. Furthermore, ZnFe₂O₄ nanoparticles have the crystallite size in the range 5–10 nm, as confirmed by TEM. The magnetic measurements exhibited that the zinc ferrite nanoparticles synthesized at 40 °C were superparamagnetic with the maximum magnetization of 7.3 emu/g at 10 kOe.