N2���������֦������ڸ��Լ�Ⱦɫ�ij����о�

本研究用氮气等离子体固相表面修饰改性对丙纶纤维进行表面处理。用傅立叶变换红外光谱分析改性前后样品表面官能团变化,用扫描电镜分析改性前后样品表面的形貌变化,用紫外可见分光光度计测试样品的上染率。结果表明:等离子体表面处理及丙烯酸接枝后的丙纶纤维表面引入了羰基、胺(氨)基或酰胺等活性基,使丙纶纤维从不可上染到能染上鲜艳的阳离子艳兰,显著改善了丙纶纤维的染色品质。     

Surface modification of polypropylene non-woven fabric using atmospheric nitrogen dielectric barrier discharge plasma

In this paper, a dielectric barrier discharge operating in nitrogen at atmospheric pressure has been used to improve the surface hydrophilic property of polypropylene (PP) non-woven fabric. The changes in the hydrophilic property of the modified PP samples are investigated by the contact angle measurements and the variation of water contact angle is obtained as a function of the energy density; micrographs of the PP before and after plasma treatment are observed by scanning electron microscopy (SEM) and the chemical composition of the PP surface before and after plasma treatment is also analyzed by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The results show that the surface hydrophilic property of the PP samples is greatly improved with plasma treatment for a few seconds, as evidenced by the fact that the contact angle of the treated PP samples significantly decreases after plasma treatment. The analysis of SEM shows that the surface roughness of the treated PP samples increases due to bonding and etching in plasma processing. The analyses of FTIR and the C1s peak in the high-resolution XPS indicate that oxygen-containing and nitrogen-containing polar functional groups are introduced into PP surface in plasma processing. It can be concluded that the surface hydrophilic property of the modified PP samples has been obviously improved due to the introduction of oxygen-containing and nitrogen-containing polar groups and the increase of the surface roughness on the PP surface.     

染色温度对叶绿素铜钠盐上染蚕丝织物的影响

研究了染色温度对叶绿素铜钠盐上染蚕丝织物的上染速率、染色织物颜色特征值及色牢度的影响。结果表明,在40—90℃染色温度范围内,当温度为70℃时,叶绿素铜钠盐上染蚕丝初期上染速率、平衡上染率均最大,染色蚕丝织物最为深绿;叶绿素铜钠盐染色蚕丝织物具有很好的耐洗和耐摩擦牢度（4级及以上）,但其耐日光色牢度较差（2—3级）;提高染色温度、延长染色时间对染色蚕丝织物的耐日光色牢度没有明显影响。叶绿素铜钠盐染色蚕丝织物适宜制作高档的居家服饰。     

Cold Pad-Batch dyeing method for cotton fabric dyeing with reactive dyes using ultrasonic energy

Reactive dyes are vastly used in dyeing and printing of cotton fibre. These dyes have a distinctive reactive nature due to active groups which form covalent bonds with -OH groups of cotton through substitution and/or addition mechanism. Among many methods used for dyeing cotton with reactive dyes, the Cold Pad Batch (CPB) method is relatively more environment friendly due to high dye fixation and non requirement of thermal energy. The dyed fabric production rate is low due to requirement of at least twelve hours batching time for dye fixation. The proposed CPB method for dyeing cotton involves ultrasonic energy resulting into a one third decrease in batching time. The dyeing of cotton fibre was carried out with CI reactive red 195 and CI reactive black 5 by conventional and ultrasonic (US) method. The study showed that the use of ultrasonic energy not only shortens the batching time but the alkalis concentrations can considerably be reduced. In this case, the colour strength (K/S) and dye fixation (%F) also enhances without any adverse effect on colour fastness of the dyed fabric. The appearance of dyed fibre surface using scanning electron microscope (SEM) showed relative straightening of fibre convolutions and significant swelling of the fibre upon ultrasonic application. The total colour difference values ΔE (CMC) for the proposed method, were found within close proximity to the conventionally dyed sample.     

Physicochemical characterization of thermally aged Egyptian linen dyed with organic natural dyestuffs

A number of organic natural dyestuffs used in dyeing in ancient times, i.e. indigo, madder, turmeric, henna, cochineal, saffron and safflower, have been used to colour Egyptian fabrics based on linen. Their physicochemical properties have been evaluated on thermally aged linen samples. The aged dyed linen samples were thoroughly examined by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile strength and elongation measurements. It was found that, in the molecular level, dyes interact mainly with the cellulose compounds of the aged linen while in the macroscopic level tensile and elongation parameters are altered. Tensile strength is positively related to the dye treatment while elongation depends specifically on the type of the dye used. Results converge that the dyed textiles did indeed play a role as protecting agents affecting strength and reducing thermal deterioration.     

Modification of surface properties of polypropylene (PP) film using DC glow discharge air plasma

The industrial use of polypropylene (PP) films is limited because of undesirable properties such as poor adhesion and printability. In the present study, a DC glow discharge plasma has been used to improve the surface properties of PP films and make it useful for technical applications. The change in hydrophilicity of modified PP film surface was investigated by contact angle (CA) and surface energy measurements as a function of exposure time. In addition, plasma-treated PP films have been subjected to an ageing process to determine the durability of the plasma treatment. Changes in morphological and chemical composition of PP films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The improvement in adhesion was studied by measuring T-peel and lap shear strength. The results show that the surface hydrophilicity has been improved due to the increase in the roughness and the introduction of oxygen-containing polar groups. The AFM observation on PP film shows that the roughness of the surface increased due to plasma treatment. Analysis of chemical binding states and surface chemical composition by XPS showed an increase in the formation of polar functional groups and the concentration of oxygen content on the plasma-processed PP film surfaces. T-peel and lap shear test for adhesion strength measurement showed that the adhesion strength of the plasma-modified PP films increased compared with untreated films surface.     

Ultrasonic dyeing of cationized cotton fabric with natural dye. Part 1: cationization of cotton using Solfix E

The dyeing of cationized cotton fabric with Solfix E using colouring matter extracted from Cochineal dye has been studied using both conventional and ultrasonic techniques. Factors affecting dye extraction such as ultrasound power, particle size, extraction temperature and time were studied. The results indicated that the extraction by ultrasound at 300 W was more effective at lower temperature and time than conventional extraction. The effect of various factors of dye bath such as pH, salt concentration, ultrasound power, dyeing time and temperature were investigated. The colour strength values obtained were found to be higher with ultrasound than with conventional techniques. The results of fastness properties of the dyed fabrics were fair to good. The scanning electron microscope (SEM) images of the morphological and X-ray analyzes were measured for cationized cotton fabrics dyed with both conventional and ultrasound methods, thus showing the sonicator efficiency.     

Ultrasonic-assisted dyeing of Nylon-6 nanofibers

We first time report ultrasonic dyeing of the Nylon 6 nanofibers with two disperse dyes CI Disperse blue 56 and CI Disperse Red 167:1 by utilising ultrasonic energy during dyeing process. The Nylon 6 nanofibers were fabricated via electrospinning and dyed via batchwise method with and without sonication. Results revealed that ultrasonic dyeing produce higher color yield (K/S values) and substantially reduces dyeing time from 60 min for conventional dyeing to 30 min can be attributed to breakage of dye aggregate, transient cavitation near nanofiber surface and mass transfer within/between nanofibers. Color fastness results exhibited good to very good dye fixation. SEM images exhibit insignificant effect of sonication on morphology of the nanofibers. Our research results demonstrate ultrasonic dyeing as a better dyeing technique for Nylon 6 nanofibers with higher color yield and substantially reduced dyeing time.     

ADBD plasma surface treatment of PES fabric sheets

Plasma treatment of textile fabrics is investigated as an alternative to the environmentally hazardous wet chemical fabric treatment and pretreatment processes. Plasma treatment usually results in modification of the uppermost atomic layers of a material surface and leaves the bulk characteristics unaffected. It may result in desirable surface modifications, e.g. surface etching, surface activation, cross-linking, chain scission and oxidation. Presented paper contains results of the applicability study of the atmospheric pressure dielectric discharge (ADBD), i.e. dielectric barrier discharge sustaining in air at atmospheric pressure and ambient temperature for synchronous treatment of several sheets of fabric. For tests sheets of polyester fabric were used. Effectivity of the modification process was determined with hydrophilicity measurements evaluated by means of the drop test. Hydrophilicity of individual sheets of fabric has distinctly increased after plasma treatment. Plasma induced surface changes of textiles were also proven by identification of new functional groups at the modified polyester fabric surface. Existence of new functional groups was detected by ESCA scans. For verification of surface changes we also applied high-resolution microphotography. It has shown distinct variation of the textile surface after plasma treatment. Important aspect for practical application of the plasma treatment is the modification effect time-stability, i.e. time stability of acquired surface changes of the fabric. The recovery of hydrophobicity was fastest in first days after treatment, later gradually diminished until reached almost original untreated state.     

Ultrasound energy to accelerate dye uptake and dye–fiber interaction of reactive dye on knitted cotton fabric at low temperatures

Acoustic cavitation formed due to propagation of ultrasound wave inside a dye bath was successfully used to dye cotton fabric with a reactive dye at lower temperatures. The energy input to the system during sonication was 0.7 W/cm². This was within the energy range that contributes towards forming cavitation during ultra-sonication. The influence of ultrasound treatment on dye particle size and fiber morphology is discussed. Particle size analysis of the dye bath revealed ultra-sonication energy was capable of de-agglomeration of hydrolyzed dye molecules during dyeing. SEM micrograph and AFM topographical image of the fiber surface revealed fiber morphology remains unchanged after the sonication. The study was extended in understanding the contribution of ultrasound method of dyeing towards achieving good color strength on the fabric, compared to the normal heating method of dyeing. Study showed color strength obtained using ultra sound method of dyeing is higher compared to normal heating dyeing. Ultrasound energy was able to achieve the good color strength on cotton fabric at very low temperature such as 30 °C, which was approximately 230% more than the color strength achieved in normal heating method of dyeing. This indicates that energy input to the system using ultrasound was capable of acting as an effective alternative method of dyeing knitted cotton fabrics with reactive dye.     

Influence of argon/oxygen atmospheric dielectric barrier discharge treatment on desizing and scouring of poly (vinyl alcohol) on cotton fabrics

The effect of argon/oxygen atmospheric dielectric barrier discharge (DBD) treatment on desizing and scouring of polyvinyl alcohol (PVA) on cotton fabric was studied with respect to the treatment duration of 1, 2, 4 and 6 min. X-ray photoelectron spectroscopy (XPS) analysis indicated that oxygen concentration increased for the plasma treated PVA film. Solubility measurement revealed that plasma treatment increased PVA solubility in hot washing but less effective in cold washing. Scanning electron microscopy (SEM) showed that the fiber surfaces were as clean as unsized fibers after 6 min treatment followed by hot washing. Wickability analysis indicated that the capillary heights of plasma treated fabrics increased significantly as the plasma treatment duration increased. The results of the yarn tensile strength test showed that the plasma treatment did not have a negative effect on fabric tensile strength.     

Plasma enhanced CVD of SiOxCyHz thin film on different textile fabrics: Influence of exposure time on the abrasion resistance and mechanical properties

In order to improve textile fabric abrasion resistance, in this work a SiO_xC_yH_z thin film was realized by low pressure plasma chemical vapour deposition (PCVD) at room temperature, using hexamethyldisiloxane (HMDSO) as precursor compound. To test changes in the performance properties of the surface finished samples as a function of the type of the substrate, the deposition was carried out on different textile fabrics. The polymerization processes were followed by weight measurements of textile fabrics. It was found that, after PCVD, a significantly lower fabric weight loss was observed on treated samples after rubbing than on the untreated samples. The morphology, elemental composition and type of chemical bonding present in the film applied on textile fabrics were also investigated using electron scanning microscopy (SEM), energy dispersive X-ray (EDX) and infrared spectroscopy techniques (FT-IR (ATR)). The results showed a substantial enhancement of wear resistance for the surfaces modified with the presented process, while tensile and tearing strength were adversely affected.     

Functionalization of PET and PA6.6 woven fabrics

In the present work as received woven fabrics of polyethylene terephthalate (PET) and polyamide 6.6 (PA6.6) were exposed to a continuous dielectric barrier discharge (DBD), in air at atmospheric pressure, at selected discharge power values and conveyor speeds. The chemical modification of the fabric surface was studied by contact angle analysis, attenuated total reflection (ATR)-FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS). The results confirmed that the treatment changed the fabric surface chemistry, increasing its wettability by polar liquids and its oxygen content. Contact angle results showed different behaviour of the two polymer fabrics toward ageing effects; while PET showed a contact angle increase along the subsequent days of treatment, the PA6.6 fabric maintained its hydrophilicity even 15 days after treatment. The surface morphology analysed by scanning electron microscopy (SEM), did not show any significant difference before and after treatment.     

Surface enhanced Raman spectroscopic investigation of orchil dyed wool from Roccella tinctoria and Lasallia pustulata

In this work Raman spectroscopic techniques have been utilized to characterize the vibrational spectral features of orchil dyed wool samples. Specifically, it is noted by surface enhanced Raman spectroscopy that wool dyed purple with two historically used orchil species (Roccella tinctoria and Lasallia pustulata) show spectral differences possibly owing to their specific dye‐precursor constituents. The additional natural dyestuff woad (Isatis tinctoria L.) overdyeing the R. tinctoria orchil dyed wool is a further challenge when distinguishing the mixed dye components given by the co‐adsorption of the dyestuffs as permitted by the selection rules of surface enhanced Raman spectroscopy. Furthermore, the effects of dilution of the L. pustulata species in its spectral detection have been assessed along with the evaluation of subsequent lichen extract boiling before dyeing which resulted in the detection of a degraded form of the orchil dye. Proof of concept included the surface enhanced Raman spectroscopy (SERS) investigation of a purple dyed tapestry (XVI century) which permitted an aged orchil dye to be determined. This contribution utilizes SERS as a fast, reproducible and specific method for both orchil dye detection and alteration induced by degradation. Copyright © 2014 John Wiley & Sons, Ltd.     

交流和纳秒脉冲Ar/H2O介质阻挡放电聚丙烯材料表面亲水改性对比研究

为了提高等离子体对聚合物材料表面处理的应用效果,优化亲水处理的条件,研究了交流和纳秒脉冲氩气介质阻挡放电（DBD）中添加适量H₂O,对聚丙烯（PP）亲水改性的处理效果。利用电学和光学诊断方法,系统地对比了交流DBD和纳秒脉冲DBD的放电特性,结果表明,纳秒电源驱动DBD具有更高的放电瞬时功率,更好的放电均匀性和更高的能量效率。通过测量不同水蒸气含量下DBD的OH发射光谱强度,确定了PP材料亲水性处理中H₂O添加的最优含量。利用交流和纳秒脉冲电源驱动DBD分别对PP材料进行亲水改性的处理,测量了不同条件下改性处理后的表面水接触角,并利用原子力显微镜（AFM）和傅里叶红外光谱（FTIR）分别对处理前后PP材料的表面物理形貌和表面化学成分进行分析。结果发现,经DBD处理后PP材料的水接触角明显降低,表面粗糙度明显增大,表面的亲水性含氧基团,羟基（?OH）和羰基（C=O）的数量大幅增加。相比交流电源,纳秒脉冲DBD处理的改性效果更好,其处理后的材料表面水接触角,比交流DBD处理的低5°左右,表面粗糙度也有所提升。而水蒸气的加入可使PP材料的表面水接触角进一步减小4°左右,表面粗糙度明显提升。研究结果为优化DBD聚合物材料表面改性实验条件及处理的效果提供了重要的参考依据。     

Self-assembled monolayer growth on chemically modified polymer surfaces

We report a study of the self-assembled monolayer (SAM) growth of bis[3(triethoxysilane)propyl]tetrasulfide (Tetrasulfide) on low dielectric constant (low-k) aromatic hydrocarbon SiLK whose surface chemistry was modified using sulfuric acid, He plasma treatment, and N₂ plasma treatment. X-ray photoelectron spectroscopy (XPS) spectra show that there is no detectable growth of Tetrasulfide SAM on untreated SiLK surfaces. After the SiLK surfaces have been treated with sulfuric acid, He plasma, or N₂ plasma, the original chemically inert polymer surfaces are functionalized with polar groups resulting in a significant improvement of their wettability, which is confirmed by their reduction of water droplet contact angles. The introduction of polar functional groups thus facilitates the formation of Tetrasulfide SAM on the polymer surfaces. Atomic force microscopy (AFM) analysis shows an insignificant change in the surface morphology after the growth of Tetrasulfide SAM on the chemically modified SiLK surfaces. Quantitative XPS analysis also showed that Tetrasulfide SAM growth is more prominent on He and N₂ plasma treated surfaces than those treated by sulfuric acid.     

Surface analysis of oxygen plasma treated poly(p-phenylene benzobisoxazole) fibers

The influence of oxygen plasma treatment on surface properties of poly(p-phenylene benzobisoxazole) (PBO) fibers and aging effect of the oxygen plasma modified PBO fiber surfaces were investigated by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA), respectively. The results indicated that the oxygen plasma treatment introduced some polar groups to PBO fiber surfaces, enhanced surface roughness and changed surface morphologies of PBO fibers by plasma etching and oxidative reactions. Surface wettability of PBO fibers may be significantly improved by increasing surface free energy of the fibers via oxygen plasma treatment. Aging effect of the oxygen plasma treated PBO fibers showed that the fiber surface wettability degraded in the first several days after the plasma treatment, and it was found to be changeless as the aging time continued as long as 30 days.     

Effect of Filler Treatment on Crystallization,Morphology and Mechanical Properties of Polypropylene/Calcium Carbonate Composites

Pimelic acid (PA) was used as a new surface modifier for CaCO₃. The effects of PA treatment on the crystallization, morphology, and mechanical properties of PP/CaCO₃ composites were investigated. Fourier transform infrared (FTIR) spectroscopy analysis revealed that PA bonded to CaCO₃ and formed a calcium pimelate surface layer after reacting with CaCO₃. The results of wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), and polarized light microscopy (PLM) proved that the PA treated CaCO₃ induced a large amount of β -iPP and decreased the spherulitic size of PP. The results of scanning electron microscopy (SEM) showed that the PA treatment enhanced the interfacial adhesion between the filler and the matrix, indicating the improvement of the compatibility between PP and CaCO₃. The toughness of the composites was improved by the more ductile β -form spherulites. When 1% of PA treated CaCO₃ was added, the notched impact strength reached its maximum, a value of 19.79 kJ/m², which was 3.64 times greater than that of the pure PP.     

Ultrasonic dyeing of cellulose nanofibers

Textile dyeing assisted by ultrasonic energy has attained a greater interest in recent years. We report ultrasonic dyeing of nanofibers for the very first time. We chose cellulose nanofibers and dyed with two reactive dyes, CI reactive black 5 and CI reactive red 195. The cellulose nanofibers were prepared by electrospinning of cellulose acetate (CA) followed by deacetylation. The FTIR results confirmed complete conversion of CA into cellulose nanofibers. Dyeing parameters optimized were dyeing temperature, dyeing time and dye concentrations for each class of the dye used. Results revealed that the ultrasonic dyeing produced higher color yield (K/S values) than the conventional dyeing. The color fastness test results depicted good dye fixation. SEM analysis evidenced that ultrasonic energy during dyeing do not affect surface morphology of nanofibers. The results conclude successful dyeing of cellulose nanofibers using ultrasonic energy with better color yield and color fastness results than conventional dyeing.     

Surface properties of platinum thin films as a function of plasma treatment conditions

We examined the surface properties of platinum (Pt) thin films exposed to oxygen and argon plasma treatments and compared them to as-deposited Pt films. The surface wetting properties, refractive index and extinction coefficient of the Pt films were monitored as a function of time after different plasma treatments. Surfaces treated with an oxygen plasma were dramatically different from as-deposited Pt, whereas argon plasma treated surfaces were similar to as-deposited films. X-ray photoelectron spectroscopy confirmed the formation of platinum oxide on films treated with an oxygen plasma, while such oxide diminished after argon plasma treatment. Surface morphology studied with atomic force microscopy indicated a strong dependence of the surface roughness of the Pt films on the power and duration of the argon plasma used for the treatment. Based on these studies, an oxygen plasma treatment followed by a brief low-power argon plasma etch was developed for the purpose of regenerating clean and metallic Pt surfaces, and at the same time providing the smoothest possible surface morphology.