Bioactive glass thin films deposited by magnetron sputtering technique: The role of working pressure

Bioglass coatings were prepared by radio frequency magnetron sputtering deposition at low temperature (150 °C) onto silicon substrates. The influence of argon pressure values used during deposition (0.2 Pa, 0.3 Pa and 0.4 Pa) on the short-range structure and biomineralization potential of the bioglass coatings was studied. The biomineralization capability was evaluated after 30 days of immersion in simulated body fluid. SEM-EDS, XRD and FTIR measurements were performed. The tests clearly showed strong biomineralization features for the bioglass films. The thickness of the chemically grown hydroxyapatite layers was more than twice greater for the BG films deposited at the highest working pressure, in comparison to those grown on the films obtained at lower working pressures. The paper attempts to explain this experimental fact based on structural and compositional considerations.     

Epitaxial growth and optical characterization of compound semiconductor β-FeSi2 prepared by pulsed laser deposition

β-FeSi₂ thin films were prepared on FZ n-Si (1 1 1) substrates by pulsed laser deposition (PLD). The structural properties and crystallographic orientation of the films were investigated by X-ray diffraction (XRD) analysis. This indicates that β-FeSi₂/Si (2 0 2/2 2 0) and the single-crystalline β-FeSi₂ can be prepared using PLD. In photoluminescence (PL) measurements at 8 K detected by Ge detector, the PL spectra of the samples annealed at 900 °C for 1, 5, 8 and 20 h showed that the PL intensity of the A-band peak increased depending on annealing time in comparison with those of as-deposited samples. The intrinsic PL intensity of the A-band peak at 0.808 eV of the β-FeSi₂ from the 20-h-annealed sample was investigated for the first time by the PLD method detected by an InGaAs detector. This result has been confirmed by temperature dependence and excitation power density of the 20-h-annealed sample with the comparison of other defect-related band peaks of the sample. Cross-sectional scanning electron microscopy (SEM) observation was also performed and the thickness of the thin films was found to be at 75 nm for 20-h-annealed. The thermal diffusion for the epitaxial growth of β−FeSi₂/Si was observed when the compositional ratio of Fe to Si was around Fe:Si=1:2 for 20-h-annealed carried out by energy dispersive X-ray spectroscopy (EDX). We discussed high crystal quality of the epitaxial growth and optical characterization of β-FeSi₂ achieved after annealing at 900 °C for 20 h.     

Adsorption and desorption of Ca and PO4 species from SBFs on RF-sputtered calcium phosphate thin films

RF magnetron sputtering of calcium phosphate (CaP) coatings is a promising technique to apply thin bioactive films on bulk implant materials. In this paper the properties of the interface between RF sputtered coatings and simulated body fluids (SBFs) are related to the ability to form CaP crystals on the coating surface. Two types of coatings were compared: coatings with a low Ca over P ratio (∼0.8; CaP_low), which remain inert when immersed in SBF₂ (i.e. SBF with twice the Ca and PO₄ concentrations), and coatings with a high Ca over P ratio (1.6; CaP_high), which show the formation of CaP crystals on their surface within 2 h. Low energy ion scattering (LEIS) and radioactive labeling of the SBFs combined with liquid scintillation counting (LSC) allowed us to study very accurately the composition of the adsorbates of both coating groups after 10 min of immersion in SBF₂. For the adsorbate on CaP_high and CaP_low coatings coverages were found consistent with ionic adsorption and Ca/P ratios of 1.24 ± 0.02 and 2.17 ± 0.10, respectively. Adsorption was found to be reversible over the studied immersion period. After an induction period of 40 min a CaP precipitate started to form on the CaP_high coatings with a Ca/P ratio of 1.30 ± 0.02. Further, no significant desorption of coating species was observed during this induction period.     

The interface reaction of high-k La2Hf2O7/Si thin film grown by pulsed laser deposition

The La₂Hf₂O₇ films have been deposited on Si (1 0 0) substrate by using pulsed laser deposition (PLD) method. X-ray diffraction (XRD) demonstrates that the as-grown film is amorphous and crystallizes after 1000 °C annealing. The interface structure is systematically studied by Synchrotron X-ray reflectivity (XRR), Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Silicide, silicate and SiO_x formations from interfacial reaction are observed on the surface of the Si substrate in the as-grown film. The impact of silicide formation on the electrical properties is revealed by capacitance-voltage (C-V) measurements. By post-deposition annealing (PDA), silicide can be effectively eliminated and C-V property is obviously improved.     

Swift heavy ion induced modifications in cobalt doped ZnO thin films: Structural and optical studies

Modifications in the structural and optical properties of 100 MeV Ni⁷⁺ ions irradiated cobalt doped ZnO thin films (Zn_1−xCo_xO, x = 0.05) prepared by sol-gel route were studied. The films irradiated with a fluence of 1 × 10¹³ ions/cm² were single phase and show improved crystalline structure with preferred C-axis orientation as revealed from XRD analysis. Effects of irradiation on bond structure of thin films were studied by FTIR spectroscopy. The spectrum shows no change in bonding structure of Zn-O after irradiation. Improved quality of films is further supported by FTIR studies. Optical properties of the pristine and irradiated samples have been determined by using UV-vis spectroscopic technique. Optical absorption spectra show an appreciable red shift in the band gap of irradiated Zn_1−xCo_xO thin film due to sp-d interaction between Co²⁺ ions and ZnO band electrons. Transmission spectra show absorption band edges at 1.8 eV, 2.05 eV and 2.18 eV corresponding to d-d transition of Co²⁺ ions in tetrahedral field of ZnO. The AFM study shows a slight increase in grain size and surface roughness of the thin films after irradiation.     

Surface morphology and luminescence characterization of β-FeSi2 thin films prepared by pulsed laser deposition

β-FeSi₂ thin films were prepared on Si (1 1 1) substrates by pulsed laser deposition (PLD) with a sintering FeSi₂ target and an electrolytic Fe target. The thin films without micron-size droplets were prepared using the electrolytic Fe target; however, the surface without droplets was remarkably rougher using the Fe target than using the FeSi₂ target. After deposition at 600 °C and then annealing at 900 °C for 20 h, XRD indicated that the thin film prepared using the Fe target had a poly-axis-orientation, but that prepared using the FeSi₂ target had a one-axis-orientation. The PL spectra of the thin films prepared using the FeSi₂ and Fe targets at a growth temperature of 600 °C and subsequently annealed at 900 °C for 20 h had A-, B- and C-bands. Moreover, it was found that the main peak at 0.808 eV (A-band) in the PL spectrum of the thin films prepared using the FeSi₂ target was the intrinsic luminescence of β-FeSi₂ from the dependence of PL peak energy on temperature and excitation power density.     

Structural, optical and magnetic properties of (ZnO)1−x(MnO2)x thin films deposited at room temperature

The structural, magnetic and optical properties of (ZnO)_1−x(MnO₂)_x (with x = 0.03 and 0.05) thin films deposited by pulsed laser deposition (PLD) were studied. The pellets used as target, sintered at different temperatures ranging from 500 °C to 900 °C, were prepared by conventional solid state method using ZnO and MnO₂ powders. The observation of non-monotonic shift in peak position of most preferred (1 0 1) ZnO diffraction plane in XRD spectra of pellets confirmed the substitution of Mn ions in ZnO lattice of the sintered targets. The as-deposited thin film samples are found to be polycrystalline with the preferred orientation mostly along (1 1 0) diffraction plane. The UV-vis spectroscopy of the thin films revealed that the energy band gap exhibit blue shift with increasing Mn content which could be attributed to Burstein-Moss shift caused by Mn doping of the ZnO. The deposited thin films exhibit room temperature ferromagnetism having effective magnetic moment per Mn atom in the range of 0.9-1.4μ_B for both compositions.     

Characterization of pulsed laser deposited chalcogenide thin layers

In this work we report on pulsed laser deposition (PLD) of chalcogenide thin films from the systems (AsSe)_100−xAgI_x and (AsSe)_100−xAg_x for sensing applications. A KrF* excimer laser (λ = 248 nm; τ_FWHM = 25 ns) was used to ablate the targets that had been prepared from the synthesised chalcogenide materials. The films were deposited in either vacuum (4 × 10⁻⁴ Pa) or argon (5 Pa) on silicon and glass substrates kept at room temperature. The basic properties of the films, including their morphology, topography, structure, and composition were characterised by complementary techniques. Investigations by X-ray diffraction (XRD) confirmed the amorphous nature of the films, as no strong diffraction reflections were found. The film composition was studied by energy dispersive X-ray (EDX) spectroscopy. The morphology of the films investigated by scanning electron microscopy (SEM), revealed a particulate-covered homogeneous surface, typical of PLD. Topographical analyses by atomic force microscopy (AFM) showed that the particulate size was slightly larger in Ar than in vacuum. The uniform surface areas were rather smooth, with root mean square (rms) roughness increasing up to several nanometers with the AgI or Ag doping. Based upon the results from the comprehensive investigation of the basic properties of the chalcogenide films prepared by PLD and their dependence on the process parameters, samples with appropriate sorption properties can be selected for possible applications in cantilever gas sensors.     

Bioactive glass and hydroxyapatite thin films obtained by pulsed laser deposition

Bioactive glass (BG), calcium hydroxyapatite (HA), and ZrO₂ doped HA thin films were grown by pulsed laser deposition on Ti substrates. An UV KrF^* (λ = 248 nm, τ ≥ 7 ns) excimer laser was used for the multi-pulse irradiation of the targets. The substrates were kept at room temperature or heated during the film deposition at values within the (400-550 °C) range. The depositions were performed in oxygen and water vapor atmospheres, at pressure values in the range (5-40 Pa). The HA coatings were heat post-treated for 6 h in a flux of hot water vapors at the same temperature as applied during deposition. The surface morphology, chemical composition, and crystalline quality of the obtained thin films were studied by scanning electron microscopy, atomic force microscopy, and X-ray diffractometry. The films were seeded for in vitro tests with Hek293 (human embryonic kidney) cells that revealed a good adherence on the deposited layers. Biocompatibility tests showed that cell growth was better on HA than on BG thin films.     

Preparation of transparent conductive TiO2:Nb thin films by pulsed laser deposition

This study investigated the optical and electrical properties of Nb-doped TiO₂ thin films prepared by pulsed laser deposition (PLD). The PLD conditions were optimized to fabricate Nb-doped TiO₂ thin films with an improved electrical conductivity and crystalline structure. XRD analyses revealed that the deposition at room temperature in 0.92 Pa O₂ was suitable to produce anatase-type TiO₂. A Nb-doped TiO₂ thin film attained a resistivity as low as 6.7 × 10⁻⁴ Ω cm after annealing at 350 °C in vacuum (<10⁻⁵ Pa), thereby maintaining the transmittance as high as 60% in the UV-vis region.     

Microstructure and interfacial properties of HfO2-Al2O3 nanolaminate films

High-k HfO₂-Al₂O₃ composite gate dielectric thin films on Si(1 0 0) have been deposited by means of magnetron sputtering. The microstructure and interfacial characteristics of the HfO₂-Al₂O₃ films have been investigated by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and spectroscopic ellipsometry (SE). Analysis by XRD has confirmed that an amorphous structure of the HfO₂-Al₂O₃ composite films is maintained up to an annealing temperature of 800 °C, which is much higher than that of pure HfO₂ thin films. FTIR characterization indicates that the growth of the interfacial SiO₂ layer is effectively suppressed when the annealing temperature is as low as 800 °C, which is also confirmed by spectroscopy ellipsometry measurement. These results clearly show that the crystallization temperature of the nanolaminate HfO₂-Al₂O₃ composite films has been increased compared to pure HfO₂ films. Al₂O₃ as a passivation barrier for HfO₂ high-k dielectrics prevents oxygen diffusion and the interfacial layer growth effectively.     

Structural and morphological characterization of TiO2 nanostructured films grown by nanosecond pulsed laser deposition

TiO₂ has attracted a lot of attention due to its photocatalytic properties and its potential applications in environmental purification and self cleaning coatings, as well as for its high optical transmittance in the visible-IR spectral range, high chemical stability and mechanical resistance. In this paper, we report on the growth of TiO₂ nanocrystalline films on Si (1 0 0) substrates by pulsed laser deposition (PLD). Rutile sintered targets were irradiated by KrF excimer laser (λ = 248 nm, pulse duration ∼30 ns) in a controlled oxygen environment and at constant substrate temperature of 650 °C. The structural and morphological properties of the films have been studied for different deposition parameters, such as oxygen partial pressure (0.05-5 Pa) and laser fluence (2- 4 J/cm²). X-ray diffraction (XRD) shows the formation of both rutile and anatase phases; however, it is observed that the anatase phase is suppressed at the highest laser fluences. X-ray photoelectron spectroscopy (XPS) measurements were performed to determine the stoichiometry of the grown films. The surface morphology of the deposits, studied by scanning electron (SEM) and atomic force (AFM) microscopies, has revealed nanostructured films. The dimensions and density of the nanoparticles observed at the surface depend on the partial pressure of oxygen during growth. The smallest particles of about 40 nm diameter were obtained for the highest pressures of inlet gas.     

Nanostructural pulse laser-deposited Ag(Tl)SbS semiconductor thin films: Growth dynamics, structural and electrical properties

Ag₃SbS₃ semiconductor material is an attractive substance for different optoelectronic and data storage applications [D. Adler, M.S. Shur, M. Silver, S.R. Ovchinsky, J. Appl. Phys. 51 (1979) 3289]. The most reliable way to get thin films with proper quality is the pulse laser deposition (PLD) technology. The paper reports data on growth dynamics (electron microscopic experiments (EME) performed in situ in order to clarify structural features of the films under PLD process), X-ray diffraction (XRD) investigations and room temperature current-voltage (IVC) characteristics. The sets of investigated samples were prepared by Nd:IAG laser. Films were deposited under substrate temperatures T = 300 K and T = 400 K and at different pulse repetition frequencies. EME studies revealed time-dependent changes of the grown films’ structure occurring under stationary pulse repetition frequency and the substrate temperature. The structure of the films was identified as an amorphous with nanoscale crystalline phase inclusions (there are results of the XRD studies). The IVCs investigations performed at the room temperature and under applied bias up to 10 V in both directions showed a domination of tunneling current for all samples under study.     

Effect of substrate temperature on the morphology, structural and optical properties of Zn1−xCoxO thin films

Zn_1−xCo_xO thin films with c-axis preferred orientation were deposited on sapphire (0 0 0 1) by pulsed laser deposition (PLD) technique at different substrate temperatures in an oxygen-deficient ambient. The effect of substrate temperature on the microstructure, morphology and the optical properties of the Zn_1−xCo_xO thin films was studied by means of X-ray diffraction (XRD), atomic force microscopy (AFM), UV-visible-NIR spectrophotometer, fluorescence spectrophotometer. The results showed that the crystallization of the films was promoted as substrate temperature rose. The structure of the samples was not distorted by the Co incorporating into ZnO lattice. The surface roughness of all samples decreased as substrate temperature increased. The Co concentration in the film was higher than in the target. Emission peak near band edge emission of ZnO from the PL spectra of the all samples was quenched because the dopant complexes acted as non-radiative centers. While three emission bands located at 409 nm (3.03 eV), 496 nm (2.5 eV) and 513 nm (2.4 eV) were, respectively, observed from the PL spectra of the four samples. The three emission bands were in relation to Zn interstitials, Zn vacancies and the complex of V_O and Zn_i (V_OZn_i). The quantity of the Zn interstitials maintained invariable basically, while the quantity of the V_OZn_i slightly decreased as substrate temperature increased.     

Pulsed laser deposited iron fluoride thin films for lithium-ion batteries

Iron fluoride thin films were successfully grown by Pulsed Laser Deposition (PLD), and their physico-chemical properties and electrochemical behaviours were examined by adjusting the deposition conditions, such as the target nature (FeF₂ or FeF₃), the substrate temperature (T_s ≤ 600 °C), the gas pressure (under vacuum or in oxygen atmosphere) and the repetition rates (2 and 10 Hz). Irrespective of the FeF₂ or FeF₃ target nature, iron fluoride thin films, deposited at 600 °C under vacuum, showed X-ray diffraction (XRD) patterns corresponding to the FeF₂ phase. On the other hand, iron fluoride thin films deposited at room temperature (RT) from FeF₂ target were amorphous, whereas the thin films deposited from FeF₃ target consisted of a two-phase mixture of FeF₃ and FeF₂ showing sharp and broad diffraction peaks by XRD, respectively. Their electrochemical behaviour in rechargeable lithium cells was investigated in the 0.05-3.60 V voltage window. Despite a large irreversible capacity on the first discharge, good cycling life was observed up to 30 cycles. Finally, their electrochemical properties were compared to the ones of iron oxide thin films.     

Microstructure of epitaxial SrRuO3 thin films on MgO substrates

SrRuO₃ thin films have been grown on singular (1 0 0) MgO substrates using pulsed laser deposition (PLD) in 30 Pa oxygen ambient and at a temperature of 400-700 °C. Ex situ reflection high-energy electron diffraction (RHEED) as well as X-ray diffraction (XRD) θ/2θ scan indicated that the films deposited above 650 °C were well crystallized though they had a rough surface as shown by atom force microscopy (AFM). XRD Φ scans revealed that these films were composed of all three different types of orientation domains, which was further confirmed by the RHEED patterns. The heteroepitaxial relationship between SrRuO₃ and MgO was found to be [1 1 0] SRO//[1 0 0] MgO and 45°-rotated cube-on-cube [0 0 1] SRO//[1 0 0] MgO. These domain structures and surface morphology are similar to that of ever-reported SrRuO₃ thin films deposited on the (0 0 1) LaAlO₃ substrates, and different from those deposited on (0 0 1) SrTiO₃ substrates that have an atomically flat surface and are composed of only the [1 1 0]-type domains. The reason for this difference was ascribed to the effect of lattice mismatch across the film/substrate interface. The room temperature resistivity of SrRuO₃ films fabricated at 700 °C was 300 μΩ cm. Therefore, epitaxial SrRuO₃ films on MgO substrate could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

Structure and properties of transparent conductive doped ZnO films by pulsed laser deposition

High quality transparent conductive ZnO thin films were deposited on quartz glass substrates using pulsed laser deposition (PLD). We varied the growth conditions such as the substrate temperature and oxygen pressure. X-ray diffraction (XRD), X-ray photoelectron spectrometer (XPS), and atomic force microscopy (AFM) measurements were done on the samples. All films show n-type conduction, the best transparent conductive oxide (TCO) performance (Al-doped ZnO = 1.33 × 10⁻⁴ Ω cm, Ga-doped ZnO = 8.12 × 10⁻⁵ Ω cm) was obtained on the ZnO film prepared at pO₂ = 5 mTorr and T_s = 300 °C.     

Effect of annealing on the properties of N-doped ZnO films deposited by RF magnetron sputtering

N-doped ZnO films were deposited by RF magnetron sputtering in N₂/Ar gas mixture and were post-annealed at different temperatures (T_a) ranging from 400 to 800 °C in O₂ gas at atmospheric pressure. The as-deposited and post-annealed films were characterized by their structural (XRD), compositional (SIMS, XPS), optical (UV-vis-NIR spectrometry), electrical (Hall measurements), and optoelectronic properties (PL spectra). The XRD results authenticate the improvement of crystallinity following post-annealing. The weak intensity of the (0 0 2) reflection obtained for the as-deposited N-doped ZnO films was increased with the increasing T_a to become the preferred orientation at higher T_a (800 °C). The amount of N-concentration and the chemical states of N element in ZnO films were changed with the T_a, especially above 400 °C. The average visible transmittance (400-800 nm) of the as-deposited films (26%) was increased with the increasing T_a to reach a maximum of 75% at 600 °C but then decreased. In the PL spectra, A⁰X emission at 3.321 eV was observed for T_a = 400 °C besides the main D⁰X emission. The intensity of the A⁰X emission was decreased with the increasing T_a whereas D⁰X emission became sharper and more optical emission centers were observed when T_a is increased above 400 °C.     

Structural and optical properties of YSZ thin films grown by PLD technique

We report on the structural and optical properties of yttria stabilized zirconia (YSZ) thin films grown by pulsed laser deposition (PLD) technique and in situ crystallized at different substrate temperatures (T_s = 400 °C, 500 °C and 600 °C). Yttria-stabilized zirconia target of ∼1 in. diameter (∼95% density) was fabricated by solid state reaction method for thin film deposition by PLD. The YSZ thin films were grown on an optically polished quartz substrates and the deposition time was 30 min for all the films. XRD analysis shows cubic crystalline phase of YSZ films with preferred orientation along 〈1 1 1〉. The surface roughness was determined by AFM for the films deposited at different substrate temperatures. The nano-sized surface roughness is found to increase with the increase of deposition temperatures. For the optical analysis, a UV-vis-NIR spectrophotometer was used and the optical band gap of ∼5.7 eV was calculated from transmittance curves.     

A facile process to prepare copper oxide thin films as solar selective absorbers

Copper oxide thin films as solar selective absorbers were conveniently prepared by one-step chemical conversion method. X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis-NIR spectra and Fourier transform infrared (FTIR) spectra were employed to characterize the composition, structure and optical properties of thin films. The results indicated that the composition, structure and optical properties of thin films were greatly influenced by reaction temperature, time and concentration of NaOH. When reaction temperature was fixed at 40 °C, the as-prepared films consist of pure cubic Cu₂O. The surface morphology of thin films was changed from square-like structure (reaction time ≤ 25 min) to porous belt-like structure (reaction time ≥ 30 min) with the elongation of reaction time. While for thin films prepared at 60 °C and 80 °C, single Cu₂O was observed after 5 min reaction. When reaction time is longer than 5 min, CuO appears and the content of CuO is increasing with the elongation of reaction time. With the increase of reaction temperature, the belt-like structure was easily formed for 60 °C/10 min and 80 °C/5 min. Decreasing concentration of NaOH also could result in the formation of CuO and porous belt-like structure. Simultaneously, the film thickness is increasing with the increase of reaction time, temperature and concentration. Films containing CuO with belt-like structure exhibited high absorptance (>0.9), and the emissivity of films increased with elongation of reaction time. Combination of the composition, structure and optical properties, it can be deduced that the porous belt-like structure like as a light trap can greatly enhance absorbance (α), while the composition, thickness and roughness of thin films can greatly influence the emissivity (?). The highest photo-thermal conversion efficiency was up to 0.86 (α/? = 0.94/0.08) for thin films prepared at 80 °C/5 min, which proved that the CuO_x thin films can be served as high performance solar selective absorbers.