Electrodeposition and tribological properties of Ni-SrSO4 composite coatings

Ni-SrSO₄ composite coatings were electrodeposited on superalloy Inconel 718 from a Watts electrolyte containing a SrSO₄ suspension. Ni-SrSO₄ coatings were investigated by scanning electron microscope, microhardness tester, and friction and wear tester in sliding against a bearing steel ball under unlubricated condition. The incorporation of SrSO₄ into Ni matrix increases the microhardness of electrodeposited coatings. Ni-SrSO₄ composite coating exhibits a distinctly low friction coefficient and a small wear rate as contrasted with pure Ni coating and the substrate. The effect of SrSO₄ particles on microstructure and tribological properties of Ni-SrSO₄ composite coatings is discussed.     

脉冲磁控溅射MoS2-Ti涂层常温及高温真空摩擦磨损性能

利用脉冲磁控溅射法,以铝青铜合金(C63200)和硅片为基底,制作不同Ti含量的MoS₂-Ti复合涂层。通过XRD、SEM、EDS、光学显微镜、多环境摩擦试验机等表征了涂层的结构成分和摩擦性能。结果表明：随Ti含量的增加,涂层致密度提升,S、Mo原子比上升。Ti的掺入使涂层由高度结晶态向非晶态转变。Ti含量增加,涂层摩擦磨损性能先上升再下降,常温真空下含3%Ti的涂层拥有稳定和低至0.015的摩擦系数,23%Ti的涂层失去润滑性。温度升高到400℃,涂层摩擦系数由0.015~0.04上升至0.07~0.1,含13%Ti的涂层高温真空下在800s后润滑失效。磨痕形貌显示,含3%Ti的涂层磨痕最窄,温度升高宽度增加不大,含13%Ti的涂层磨损严重,400℃真空环境下很快磨穿,纯MoS₂和13%Ti涂层摩擦时发现大量磨粒和破碎磨屑。     

碳纳米管增强镍磷基复合镀层研究

对CVD方法制备的碳纳米管进行表面改性处理，然后在液相中分散，利用化学共沉积方法形成碳纳米管镍磷基复合镀层，研究了碳纳米管表面改性后的红外谱、碳纳米管复合镀层的表面形貌、硬度及摩擦学行为.结果表明：碳纳米管的加入明显地提高镍磷复合镀层的硬度和改善了镍磷复合镀层的摩擦性能.硬度达到946HV，20N载荷时摩擦系数为0.7，增至80N时降为0.6；相同条件下与传统耐磨材料SiC增强的镍磷基复合镀层相比，具有更低的摩擦系数和磨损量. 关键词： 碳纳米管 表面改性 复合镀层 摩擦行为     

Fabrication of high-performance nickel/graphene oxide composite coatings using ultrasonic-assisted electrodeposition

Ultrasonic-assisted electrodeposition was used to fabricate the nickel/graphene oxide composite coatings with high hardness, low friction coefficient, and high wear resistance. In the present study, the effects of ultrasonic power and concentration of graphene oxide on the mechanical and tribological properties of the electrodeposited nickel/graphene oxide composite coatings were systematically studied. X-ray diffraction (XRD) analyses showed that the crystallite size of the nickel decreased with an increase of ultrasonic power (0–50 W, 40 KHz, square wave) and concentration of graphene oxide (0.1–0.4 g/L). Morphologies of the surface and cross-section of the composite coatings observed by Scanning Electron Microscopy (SEM) confirmed the existence of graphene oxide particles in the nickel matrix. The results from microhardness measurement demonstrated that the hardness was increased by 1.8 times using 50 W ultrasonic-assisted electrodeposition with the fixed concentration of graphene oxide (0.1 g/L), compared to the pure nickel coating. The hardness was increased by 4.4 times for the 0.4 g/L graphene oxide with the optimized ultrasonic power of 50 W in comparison to the pure nickel coating. Meanwhile, the friction coefficient decreased gradually with an increase in ultrasonic power and concentration of graphene oxide, respectively, where the effect of the concentration of graphene oxide played a more important role.     

TiN对Co基合金激光熔覆层组织与性能的影响

采用5 kW CO2激光器在低碳钢表面熔覆Co基合金涂层及TiN/Co基合金复合涂层,研究了两种涂层的组织、显微硬度以及滑动磨损性能。结果表明,Co基合金涂层主要组成相为-γCo,-εCo,Cr23C6等,TiN/Co基合金复合涂层组成相为-γCo,-εCo,Cr23C6,TiN和TiC等。Co基合金涂层由发达的-γCo枝晶和其间共晶组织所组成,TiN/Co基合金涂层典型组织为等轴固溶体以及细小的共晶组织。TiN对熔覆层的组织有显著的改善作用,促使其组织细化,树枝晶向等轴晶转化,同时可显著提高Co基合金涂层的显微硬度及耐磨性能。     

Ni-TiB2-Nd2O3复合镀层的性能研究

采用TiB2和Nd2O3微粒作为共掺杂微粒,用电沉积法制备Ni-TiB2-Nd2O3复合镀层.用电感耦合等离子体-原子发射光谱法(ICP-AES)测定镀层中Ti、Nd元素的质量百分含量(wt%);分别研究镀层中Nd2O3微粒的含量对镀层的硬度、磨损质量和摩擦系数等的影响;用X衍射法(XRD)对Ni-TiB2-Nd2O3...     

Friction and wear properties of the co-deposited Ni-SiC nanocomposite coating

Ni-SiC nanocomposite coatings were produced by electrodeposition from a nickel sulfate bath containing SiC nanoparticles with an average particle size of 30 nm. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of Ni-SiC nanocomposite coatings and Ni film were comparatively investigated sliding against Si₃N₄ ceramic balls under non-lubricated conditions. The results indicated that compared to Ni film, Ni-SiC nanocomposite coating exhibited enhanced microhardness and wear resistance. The effect of SiC nanoparticles on the friction and wear resistance is discussed in detail.     

铬-镧镀层的制备及其光谱性能

用电沉积法分别采用直流电源和脉冲电源制备铬-镧镀层(dc)和铬-镧镀层(pulse).分别用发射光谱法、X衍射法、能谱法和扣描电镜法等对镀层进行表征.铬-镧镀层(dc)为非晶态镀层,铬-镧镀层(pulse)中含有晶态的镧和碳化铬.铬-镧镀层(dc)和铬-镧镀层(pulse)的硬度分别为860.3和930.2 HV,比铬...     

铁基合金激光熔覆层的高温磨损性能

 为提高40Cr钢表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备Fe基涂层,利用HT-500摩擦磨损实验机测定干摩擦条件下,基体和熔覆层的摩擦因数随温度变化的规律。利用表面粗糙度轮廓仪测量磨痕的深度和宽度,SEM观察熔覆层以及磨痕的显微组织形貌,使用HV-1000型显微硬度仪检测基体和熔覆层结合部分的硬度。研究结果表明:熔覆层平均显微硬度值达到373.8HV(0.2);显著高于基体硬度198.4HV(0.2)。在干摩擦条件下,随着温度升高,磨损过程逐渐变平缓,平均摩擦因数降低,磨损率增加,耐磨性下降;在350~400 ℃之间,熔覆层磨损性能优于基体。     

Comparative study of titanium carbide and nitride coatings grown by cathodic vacuum arc technique

Titanium nitride (TiN), titanium carbide (TiC) thin films and TiC/TiN bilayers have been deposited on AISI 304 stainless steel substrates by plasma assisted physical vapor deposition technique—reactive pulsed vacuum arc method. The coatings were characterized in terms of crystalline structure, microstructure and chemical nature by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. Tribological behavior was investigated using ball on disc technique. The average coefficient of friction was measured, showing lower values for the TiN/TiC bilayer. Dynamic wear curves were performed for each coating, observing a better wear resistance for TiN/TiC bilayers, compared to TiN and TiC monolayers. On the other hand, the TiCN formation in the TiN/TiC bilayer was observed, being attributed to the interdiffusion between TiN and TiC at the interface. Moreover, the substrate temperature influence was analysing observing a good behavior at T_S = 115 °C.     

Microstructure, microhardness and dry friction behavior of cold-sprayed tin bronze coatings

In this paper, two types of tin bronze coatings (Cu-6 wt.% Sn and Cu-8 wt.% Sn) were prepared by cold spray process. The as-sprayed coatings were subjected to a vacuum heat treatment at 600 °C for 3 h. The coating microstructure, microhardness and tribological performance were characterized. The effects of the tin content and the vacuum heat treatment on the microstructure, microhardness and tribological behavior of the coatings were investigated. It is found that the as-sprayed CuSn6 (As6) and CuSn8 (As8) coatings exhibit practically an identical porosity. Meanwhile, As8 presents a higher microhardness than As6. In addition, the increase of the tin content in the powder feedstock leads to a lower wear rate. After a heat treatment, coating porosities are significantly reduced. However, the coating hardness is significantly decreased and the coating presents a much decreased wear resistance. For the as-sprayed coatings, such factors as ploughing and particle delamination could determine the sliding process. The heat treatment results in a distinct modification of the tribological behavior. For the annealed coatings, the adhesion, between the coating and the counterpart, could play a dominant role in the sliding process.     

激光熔覆TiC-Ni复合涂层的摩擦磨损性能和磨损机制研究

利用光学显微镜和扫描电镜观察了钛合金表面TiC-Ni激光熔覆层的宏观形貌和微观组织,测试了激光熔覆层的硬度、摩擦系数和磨损量。利用SEM观察了磨损的表面形貌和磨屑的形貌,分析了激光熔覆层的磨损机制。结果表明:激光熔覆层组织致密,无气孔和裂纹,硬度为基材的3倍;激光熔覆层的摩擦系数随环境压力的降低而提高,磨损量随环境压力的降低、法向载荷的增加而增加;低载时为轻微的磨粒磨损,高载时为严重的剥层磨损。     

铁基合金激光熔覆层高温润滑磨损性能

 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。     

Ti6Al4V合金表面激光沉积复合涂层的组织和性能

为了增强Ti6Al4V钛合金的耐磨性,采用激光沉积制造方法在其表面上制备了以原位生成的TiC颗粒和直接添加的WC颗粒为增强相的耐磨涂层,观察了各涂层的微观组织,并测量了涂层的显微硬度和涂层在室温大气条件下的摩擦磨损性能。结果表明各涂层和基体呈现冶金结合,原位自生的TiC和部分熔化的WC颗粒均能够均匀弥散分布于基体上,由于增强相颗粒的弥散强化及激光沉积组织的细晶强化作用,基材的硬度和耐磨性均得到了提高。原位自生的TiC涂层比WC涂层硬度梯度分布平缓,但耐磨性稍差。     

The effect of powder preparation method on the corrosion and mechanical properties of TiN-based coatings by reactive plasma spraying

TiN-based composite coatings with and without the addition of Cr were deposited by reactive plasma spraying (RPS) in air. Both sintered and mixed powder of Ti and B₄C were used for the RPS process. A thermodynamic model was firstly used to estimate the complicated phase composition of composite coatings prepared by RPS. The phase composition, structures and properties of TiN-based coatings were investigated using XRD, SEM and a Vickers microhardness tester. The results show that the phases in TiN-based coatings do not generate according to priority of Gibbs free energy value due to non-equilibrium reactive course during thermal spraying. The coating deposited using sintered Ti and B₄C powder is composed of two main phases (TiN and TiN_0.3), two minor phases (Ti₂O₃ and TiB₂), and a small fraction of TiC phase. The composition of the coating deposited using the mixed powder with Cr added is predominantly in the TiN and TiB₂ phases, a smaller phase fraction of Ti₂O₃ and TiO₂, and some unreacted Cr. The Vickers microhardness of the coating deposited using sintered powder is higher than that of using mixed powder. The composite coating deposited using mixed powder with the addition of Cr shows superior corrosion resistant to that using sintered powder when tested in 3.5 wt.% NaCl electrolytic solution.     

Mechanical properties of the plasma-enhanced magnetron sputtering Si-C-N coatings

The mechanical properties of plasma-enhanced magnetron sputtering Si-C-N hard coatings with various compositions are characterized. The effect of chemical composition on the microstructure and properties of coating is investigated. The results show that the microstructure and mechanical properties of Si-C-N coatings are very sensitive to chemical composition. The nanocrystalline/amorphous composite structure is beneficial to the coating's mechanical properties. It also reveals that Si-C-N coating with low Si and high C concentrations has the highest hardness (≥40 GPa) and the best wear property with dry friction coefficient about 0.2.     

Characterization of microarc oxidation coatings formed on AM60B magnesium alloy in silicate and phosphate electrolytes

Microarc oxidation coatings on AM60B magnesium alloy were prepared in silicate and phosphate electrolytes. Structure, composition, mechanical property, tribological, and corrosion resistant characteristics of the coatings was studied by scanning electron microscope (SEM), X-ray diffraction (XRD) and microhardness analyses, and by ball-on-disc friction and potentiodynamic corrosion testing. It is found that the coating produced from the silicate electrolyte is compact and uniform and is mainly composed of MgO and forsterite Mg₂SiO₄ phases, while the one formed in phosphate electrolyte is relatively porous and is mainly composed of MgO phase. The thick coating produced from a silicate electrolyte possesses a high hardness and provides a low wear rate (3.55 × 10⁻⁵ mm³/Nm) but a high friction coefficient against Si₃N₄ ball. A relatively low hardness and friction coefficient while a high wear rate (8.65 × 10⁻⁵ mm³/Nm) is recorded during the testing of the thick coating produced from a phosphate electrolyte. Both of these types of coatings provide effective protection for the corrosion resistance compared with the uncoated magnesium alloy. The coating prepared from the silicate electrolyte demonstrates better corrosion behavior due to the compacter microstructure.     

Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate

Three kinds of laser boronizing composite coatings were in situ synthesized on Ti substrate by using powders of B, BN and B₄C as starting materials. Microstructures of the laser boronizing composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM); and their worn surface morphologies were also observed by using SEM. Moreover, the friction and wear behavior of the boronizing composite coatings under dry sliding condition were evaluated using a UMT-2MT friction and wear tester. It was found that all the three types of laser boronizing composite coatings had higher microhardness and better wear resistance than pure Ti substrate; and their microstructure and wear resistance varied with varying pre-placed powders of B, BN, and B₄C. Under the same dry sliding test conditions, the wear resistance of the three kinds of laser boronizing composite coatings, i.e., sample 1 prepared from pre-placed B, sample 2 obtained from pre-placed BN, and sample 3 fabricated from pre-placed B₄C, is ranked in an order of sample 1 > sample 2 > sample 3, which, surprisingly, well conforms to their order of hardness and friction coefficients.     

Mechanical properties and wear and corrosion resistance of electrodeposited Ni-Co/SiC nanocomposite coating

Ni-Co/SiC nanocomposite coatings with various contents of SiC nano-particulates were prepared by electrodeposition in a Ni-Co plating bath containing SiC nano-particulates to be co-deposited. The influences of the nanoparticulates concentration, current density, stirring rate and temperature of the plating bath on the composition of the coatings were investigated. The shape and size of the SiC nano-particulates were observed and determined using a transmission electron microscope. The polarization behavior of the composite plating bath was examined on a PAR-273A potentiostat/galvanostat device. The wear behavior of the Ni-Co/SiC nanocomposite coatings was evaluated on a ball-on-disk UMT-2MT test rig. The worn surface morphologies of the Ni-Co/SiC nanocomposite coatings were observed using a scanning electron microscope. The corrosion behavior of the nanocomposite coatings was evaluated by charting the Tafel curves of the solution of 0.5 mol L⁻¹ NaCl at room temperature. It was found that the cathodic polarization potential of the composite electrolyte increased with increasing SiC concentration in the plating bath. The microhardness and wear and corrosion resistance of the nanocomposite coatings also increased with increasing content of the nano-SiC in the plating bath, and the morphologies of the nanocomposite coatings varied with varying SiC concentration in the plating bath as well. Moreover, the co-deposited SiC nano-particulates were uniformly distributed in the Ni-Co matrix and contributed to greatly increase the microhardness and wear resistance of the Ni-Co alloy coating.     

Electrochemical deposition and tribological behaviour of Ni and Ni-Co metal matrix composites with SiC nano-particles

Metal matrix composites reinforced with nano-sized particles have attracted scientific and technological interest due to the enhanced properties exhibited by these coatings. Ni-SiC composites have gained widespread application for the protection of friction parts in the automobile industry. The influence of variables like SiC content, current density and stirring speed on microhardness of nano-composite coatings has been studied. The improved microhardness was associated with the reduction in crystallite size determined by X-ray diffraction studies. The influence of incorporation of nano-SiC in hardened Ni-Co alloy matrix was also studied. It was observed that for 28 wt.% Co content in the matrix the microhardness was higher compared to 70 wt.% for a given nano-SiC content. This was associated to the crystal phase of Ni-28Co-SiC being fcc compared to hcp phase exhibited by Ni-70Co-SiC. The wear resistance of pure Ni, Co and nano-composite coatings was studied using pin-on-disc wear tester under dry sliding condition. The volumetric wear loss indicated that, the wear resistance of Ni-SiC nano-composite is better than that of pure nickel deposit. The wear resistance of Ni-Co composites was observed to be superior to Ni composite. The wear behaviour of Ni and Ni-28Co composite was in accordance with the Archard's law. However, the superior wear characteristic exhibited by Ni-70Co-SiC composite followed the reverse Archard's behaviour.