The size effect of Ba0.6Sr0.4TiO3 thin films on the ferroelectric properties

Barium strontium titanate (BST) thin films were prepared by RF magnetron sputtering. The dielectric constant-voltage curves and the hysteresis loops of BST thin films with different grain sizes and film thicknesses were investigated. When the grain size increases from 12 nm to 35 nm, remarkable increases in dielectric constant and tunability were observed. Above 12 nm, the BST films exhibited size effects, i.e. a decrease in maximal polarization (P_m) and an increase in coercive electric field (E_c) with reduction in grain size. In our investigation, the dielectric constant, tunability and maximal polarization increased as the film thickness increased. Furthermore, the size dependence of the dielectric constant and tunability of Ba_0.6Sr_0.4TiO₃ thin films is determined by that of the maximal polarization and the coercive electric field.     

Dependence of excess bismuth content in precursor sols on ferroelectric and dielectric properties of Bi3.25La0.75Ti3O12 thin films fabricated by chemical solution deposition

Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films were fabricated on Pt/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD), and the dependence of ferroelectric and dielectric properties of the as-deposited BLT thin films on excess Bi content in precursor sols was studied. It is found that the prepared BLT thin film shows the best polarization-electric field, capacitance-voltage and dielectric constant (?_r)-frequency characteristics, when the value of excess Bi content in precursor sols is 10%. In detail, its remnant polarization (2P_r) value is 40 μC/cm², the capacitance tunability is 21% measured at room temperature under conditions of an applied voltage of 8 V and measurement frequency of 10 kHz, and the ?_r is 696 at 100 kHz frequency.     

Low dielectric loss Ba0.6Sr0.4TiO3/MgTiO3 composite thin films prepared by a sol–gel process

The dielectric properties of Ba_0.6Sr_0.4TiO₃ (BST)/MgTiO₃ (MT) composite thin films deposited on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by the sol–gel method were investigated. The X-ray pattern analysis indicates that the thin films exhibit good crystalline quality with perovskite phase and that insertion of MT layer does not obviously affect the phase structure of BST thin films. The characterization of dielectric properties demonstrates that configuration of BST/MT/BST thin films is an effective approach to obtain low dielectric loss and dielectric tunability of BST thin films. At room temperature, the tunability of pure BST60 films and BST/MT (15 nm)/BST composite thin films is 47% and 36%, respectively, at the frequency of 1 MHz with an applied electric field of 400 kV/cm. For BST/MT/BST composite thin films, considerable reduction in the dielectric loss values is observed, which renders them attractive for tunable microwave device applications.     

Effects of interface on the dielectric properties of Ba0.6Sr0.4TiO3 thin film capacitors

Ba_0.6Sr_0.4TiO₃ thin films were deposited on Pt/SiO₂/Si substrate by radio frequency magnetron sputtering. High-resolution transmission electron microscopy (HRTEM) observation shows that there is a transition layer at BST/Pt interface, and the layer is about 7-8 nm thickness. It is found that the transition layer was diminished to about 2-3 nm thickness by reducing the initial RF sputtering power. X-ray photoelectron spectroscopy (XPS) depth profiles show that high Ti atomic concentration results in a thick interfacial transition layer. Moreover, the symmetry ν of ?_r-V curve of BST thin film is enhanced from 52.37 to 95.98%. Meanwhile, the tunability, difference of negative and positive remanent polarization (P_r), and that of coercive field (E_C) are remarkably improved.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Synthesis of fine-crystalline Ba0.6Sr0.4TiO3-MgO ceramics by novel hybrid processing route

We report the use of a novel powder-in-sol precursor hybrid processing route to synthesize dense, homogeneous, and fine-crystalline Ba_0.6Sr_0.4TiO₃-MgO (BST-MgO) ceramics as well as the study of the sintering behavior, microstructures, and dielectric properties of the ceramics. Nanosized BST powders are dispersed into BST sol-gel precursor and uniformly distributed BST slurry is obtained after ball-milling mixing. Mg(NO₃)·6H₂O solution is added to the BST slurry to give homogeneous BST-MgO slurry upon ball-milling mixing. The BST-MgO slurry is dried and calcined prior to pressing and sintering at low temperatures of 1200-1300 °C to form the ceramics. The ceramics possess very low dielectric loss tangent below 0.005 for frequency above 1 kHz and for temperature in the range −190-80 °C. The dielectric constant and dielectric tunability increase, while the ferroelectric transition broadening decreases, with increasing average grain size.     

Effects of substrates on the structure and dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films

Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films were grown on Pt(1 1 1)/Ti/SiO₂/Si and LaNiO₃(LNO)/Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel processing technique, respectively. The BTS thin films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si and annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates exhibited strong (1 1 1) and perfect (1 0 0) orientations, respectively. The BTS thin films grown on un-annealed Pt(1 1 1)/Ti/SiO₂/Si substrates showed random orientation with intense (1 1 0) peak, while the films deposited on un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate exhibited random orientation with intense (1 0 0) peak, respectively. The dielectric constant of the BTS films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si, annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si, un-annealed Pt(1 1 1)/Ti/SiO₂/Si and un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates was 512, 565, 386 and 437, respectively, measured at a frequency of 100 kHz. A high tunability of 49.7% was obtained for the films deposited on annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate, measured at the frequency of 100 kHz with an applied electric field of 200 kV/cm. The high tunability has been attributed to the (1 0 0) texture of the films and larger grain sizes.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

Microstructure and dielectric properties of (Ba0.6Sr0.4)TiO3 thin films grown on super smooth glazed-Al2O3 ceramics substrate

Modified substrates with nanometer scale smooth surface were obtained via coating a layer of CaO-Al₂O₃-SiO₂ (CaAlSi) high temperature glaze with proper additives on the rough-95% Al₂O₃ ceramics substrates. (Ba_0.6Sr_0.4)TiO₃ (BST) thin films were deposited on modified Al₂O₃ substrates by radio-frequency magnetron sputtering. The microstructure, dielectric, and insulating properties of BST thin films grown on glazed-Al₂O₃ substrates were investigated by X-ray diffraction (XRD), atomic force microscope (AFM), and dielectric properties measurement. These results showed that microstructure and dielectric properties of BST thin films grown on glazed-Al₂O₃ substrates were almost consistent with that of BST thin films grown on LaAlO₃ (1 0 0) single-crystal substrates. Thus, the expensive single-crystal substrates may be substituted by extremely cheap glazed-Al₂O₃ substrates.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Temperature-dependent ferroelectric and dielectric properties of Bi3.25La0.75Ti3O12 thin films

To investigate temperature-dependent ferroelectric and dielectric properties of ferroelectric films, Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films were prepared on Pt-coated silicon substrates by pulsed laser deposition. The ferroelectric and dielectric behaviors have been studied in a wide temperature range from 80 K to room temperature. The saturated polarization (P_sat) decreases with decreasing temperature and decreasing electric field, whereas remnant polarization (P_r) shows a more complex temperature dependence. These results, which can be well explained based on a temperature-dependent charged defects-domain wall interaction model, might be helpful for further understanding the domain switching behavior. Based on these results, an alternative way to investigate temperature-dependent ferroelectric fatigue is proposed and experimentally carried out. The measured fatigue rate is found to be linearly dependent on temperature, consistent with the report on Pb(Zr,Ti)O₃ films. Temperature-dependent dielectric measurements of the films further confirm the above explanation.     

Effect of oxygen pressure on structure and properties of Bi1.5Zn1.0Nb1.5O7 pyrochlore thin films prepared by pulsed laser deposition

The Bi₂O₃-ZnO-Nb₂O₅ (BZN) cubic pyrochlore thin films were prepared on Pt/TiO₂/SiO₂/Si(1 0 0) substrates by using pulsed laser deposition process. The oxygen pressure was varied in the range of 5-50 Pa to investigate its effect on the structure and dielectric properties of BZN thin films. It is found that oxygen pressure during deposition plays an important role on structure and other properties of BZN films. The BZN films deposited at temperature of 650 °C and at O₂ pressure of 5 Pa have an amorphous BZN and Nb₂O₅ phases but exhibits a cubic pyrochlore structure with a preferential (2 2 2) orientation when the oxygen pressure increases to 10 Pa. Dielectric constant and loss tangent of the films deposited at 10 Pa are 185 and 0.0008 at 10 kHz, respectively. The dielectric tunability is about 10% at a dc bias field of 0.9 MV/cm.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

Thermo-Sensitive Ba0.64Sr0.36TiO3 Thin Film Capacitors for Dielectric Type Uncooled Infrared Sensors

Ba_0.64Sr_0.36TiO₃ (BST) thin films are prepared on Pt/Ti/SiO₂/Si₃N₄/SiO₂/Si substrates by a sol-gel method. Thermo-sensitive BST thin film capacitors with a Metal-Ferroelectrics-Metal (M-F(BST)-M) structure are fabricated as the active elements of dielectric type uncooled infrared sensors. XRD are employed to analyze the crystallographic structures of the films. AFM observations reveal a smooth and dense surface of the films with an average grain size of about 35 nm. Rapid temperature annealing (RTA) process is a very efficient way to improve crystallization quality. The preferable annealing temperature is 800°C for 1 min. The butterfly shaped C-V curves of the capacitors indicate the films have a ferroelectric nature. The dielectric constant and dielectric loss of the films at 100 kHz are 450 and 0.038, respectively. At 25°C, where the thermo-sensitive capacitors work, the temperature coefficient of dielectric constant (TCD) is about 5.9 %/°C. These results indicate that the capacitors with sol-gel derived BST thin films are promising to develop dielectric type uncooled infrared sensors.     

Dielectric properties of continuous composition spreaded MgO-Ta2O5 thin films

The dielectric properties of MgO-Ta₂O₅ continuous composition spread (CCS) thin films were investigated. The MgO-Ta₂O₅ CCS thin films were deposited on Pt/Ti/SiO₂/Si substrates by off-Axis RF magnetron sputtering system, and then the films were annealed at 350 °C with rapid thermal annealing system in vacuum. The dielectric constant and loss of MgO-Ta₂O₅ CCS thin films were plotted via 1500 micron-step measuring. The specific point of Ta₂O₅-MgO CCS thin film (post annealed at 350 °C) showing superior dielectric properties of high dielectric constant (k ∼ 28) and low dielectric loss (tan δ < 0⋅004) at 1 MHz were found in the area of 3-5 mm apart from Ta₂O₅ side on the substrate. The cation's composition of thin film was Mg:Ta = 0.4:2 at%.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

C-V studies on metal-ferroelectric bismuth vanadate (Bi2VO5.5)-semiconductor structure

Ferroelectric bismuth vanadate Bi₂VO_5.5 (BVO) thin films have been successfully grown on p-type Si(100) substrate by using chemical solution decomposition (CSD) technique followed by rapid thermal annealing (RTA). The crystalline nature of the films has been studied by X-ray diffraction (XRD). Atomic force microscopy (AFM) was used to study the microstructure of the films. The dielectric properties of the films were studied. The capacitance-voltage characteristics have been studied in metal-ferroelectric-insulator-semiconductor (MFIS) configuration. The dielectric constant of BVO thin films formed on Si(100) is about 146 measured at a frequency of 100 kHz at room temperature. The capacitance-voltage plot of a Bi₂VO_5.5 MFIS capacitor subjected to a dc polarizing voltages shows a memory window of 1.42 V during a sweep of ±5 V gate bias. The flatband voltage (V_f) shifts towards the positive direction rather than negative direction. This leads to the asymmetric behavior of the C-V curve and decrease in memory window. The oxide trap density at a ramp rate of 0.2 V/s was estimated to be as high as 1.45×10¹² cm⁻².     

PLD and RF-PLD synthesis of Ba<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>TiO<Subscript>3</Subscript> ferroelectric thin films for electrically controlled devices

Ba_0.6Sr_0.4TiO₃ (BST) bulk ceramic synthesized by solid state reaction was used as target for thin films grown by pulsed laser deposition (PLD) and radiofrequency beam assisted PLD (RF-PLD). The X-ray diffraction patterns indicate that the films exhibit a polycrystalline cubic structure with a distorted unit cell. Scanning Electron Microscopy investigations showed a columnar microstructure with size of spherical grains up to 150 nm. The capacitance–voltage (C–V) characteristics of the BST films were performed by applying a DC voltage up to 5 V. A value of 280 for dielectric constant and 12.5% electrical tunability of the BST capacitor have been measured at room temperature.