Photochemical preparation of poly(N-vinyl-2-pyrrolidone)-stabilized platinum colloids and their deposition on titanium dioxide

Preparation processes for Pt-deposited TiO(2) (Pt/TiO(2)) by the synthesis of Pt nanoparticles and their deposition were pursued by transmission electron microscopy, extended X-ray absorption fine structure, UV-vis spectroscopy, and Fourier transform infrared spectroscopic studies. Colloidal dispersions of Pt particles stabilized by poly(N-vinyl-2-pyrrolidone) (PVP) were photochemically synthesized in aqueous ethanol solution. The average diameter of Pt particles was estimated to be 2.0 +/- 0.5 nm, which was almost unchanged by changing the reducing agent from ethanol to methanol and 2-propanol. The PVP-stabilized Pt particles were distributed over a TiO(2) surface only by mixing the Pt colloidal dispersions and TiO(2). CO was chemically coordinated on the Pt particles on a TiO(2) surface after heat treatment was carried out in an O(2) flow at 673 K to completely remove the residual PVP on Pt/TiO(2). Hydrogen reduction at 473 K did not increase the amount of CO adsorbed on Pt sites. The Pt/TiO(2) catalyst after the oxidation treatment showed higher activity for CO photooxidation than that obtained for pure TiO(2) catalyst. The CO photooxidation rate was not unchanged by the H(2) reduction.     

锆掺杂TiO_2光催化降解2-CEES和DMMP的原位红外与固体核磁研究

在国内率先将金属离子掺杂型纳米TiO_2用于化学毒剂(CWAs)洗消领域,制备了系列浓度的锆掺杂纳米TiO_2(Zr-TiO_2).为了从分子水平上认识Zr-TiO_2对CWAs的消毒机制,结合原位红外(in-situ FTIR)与固体核磁共振(SSNMR)技术,研究了掺杂前后样品表面2-CEES和DMMP的反应机理和动力学变化.结果显示:制备样品中无尿素残留,且掺杂浓度为10.05%的Zr-TiO_2光催化活性最佳;与掺杂前相比,该样品对2-CEES和DMMP的光催化降解速率加快,但反应机制不变:对DMMP的降解主要通过同时发生P-OCH3氧化和P-CH3分解,对2-CEES则依次通过C—Cl键断裂、C—S键断裂和S原子氧化完成降解,两种模拟剂在反应过程中均未生成有毒中间产物.通过研究,建立了适用于化学毒剂洗消领域的原位在线分析方法,掌握了模拟剂的光催化消毒反应机理、产物与动力学规律,为今后实毒样品的测试打下了基础.     

Photodegradation of toluene over TiO(2-x)N(x) under visible light irradiation

We report the photooxidation of toluene over nitrogen doped TiO(2) (TiO(2-x)N(x)) under visible light irradiation. The photocatalytic oxidation of toluene in air over TiO(2-x)N(x) powders was studied using diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS), gas chromatography (GC), ion chromatography (IC), and gas chromatography mass spectrometry (GC-MS), focusing on the photocatalytic decomposition processes of toluene. Results obtained indicate that toluene, weakly adsorbed on the catalyst surface, is initially photooxidized to benzaldehyde which adsorbs onto the TiO(2-x)N(x) surface more strongly, leading to the formation of ring-opening products such as carboxylic acids and aldehydes. No gaseous intermediates were detected during the photooxidation. Major intermediates adsorbed at the catalyst surface were oxalic acid, (COOH)(2), acetic acid, CH(3)COOH, formic acid, HCOOH, and pyruvic acid, CH(3)COCOOH, whereas more complicated carboxylic species, including propionic acid, CH(3)CH(2)COOH, isovaleric acid, (CH(3))(2)CHCH(2)COOH, and succinic acid, (CH(2)COOH)(2), were also found in the early stage of the photooxidation. These intermediate products were gradually photodegraded to CO(2) and H(2)O under visible light irradiation.     

Experimental study of dimethyl methylphosphonate decomposition over anatase TiO2

Removal from air and decomposition of dimethyl methylphosphonate (DMMP) over high surface area anatase TiO(2) at ambient temperature have been quantitatively studied by employing Fourier transform infrared (FTIR) technique under static conditions. In the first scenario of air purification, DMMP underwent reactive adsorption that upon completion was followed by photocatalytic oxidation. DMMP was captured over the TiO(2) surface at the speed of external diffusion. Hydrolysis of adsorbed DMMP led to methanol and methyl methylphosphonate (MMP). At low DMMP coverage quantity, it hydrolyzed completely with the formation of completely surface-bound methanol at 1% relative humidity (RH) and mostly gaseous methanol at 50% RH. Photocatalytic oxidation generated CO(2) as the only carbonaceous gaseous product and bidentate formates as the intermediate surface product. At high DMMP coverage quantity, it was captured incompletely and hydrolyzed partially with CH(3)OH in the gas phase only, 50% RH enhancing both processes. Photocatalytic oxidation generated gaseous HCOOH, CO, and CO(2) and was incomplete due to catalyst deactivation by nonvolatile products. In the second scenario of air purification, DMMP underwent adsorption, hydrolysis, and photooxidation at the same time. It resulted in the quickest removal of DMMP from the gas phase and completion of oxidation in 30 min, suggesting this process for practical air decontamination. At least 0.8 nm(2) of TiO(2) surface per each DMMP molecule should be available for complete purification of air.     

Photooxidation of dibenzothiophene on TiO(2)/hectorite thin films layered catalyst

A new titanium(IV) oxide-hectorite nanofilm photocatalyst was prepared on quartz slides. It was evaluated in the photooxidation of dibenzothiophene (DBT) in nonpolar organic solution (tetradecane), as a model for diesel fuel. A removal regimen was developed consisting of catalytic photooxidation followed by adsorption of products on silica gel. Photooxidation of DBT was performed with and without catalyst, at 254 and 300 nm. Comparison was made with a commercially available TiO(2) catalyst, Degussa P25. The catalyst was analyzed by nitrogen adsorption, XRD, SEM, and TGA-DTA. DBT concentrations were measured by HPLC and UV spectrophotometry. Preliminary qualititative analysis of products was performed by UV and HPLC. Results indicated that the outlined process was effective in reducing sulfur levels to below 10 ppm sulfur.     

Study on Chemisorption, Catalytic Behavior, and Stability of Supported Au Catalyst for the Propylene Epoxidation Reaction

The supported Au/TiO2 and Au/TiO2-SiO2 catalysts were prepared by deposition precipitation method. The TPD study reveals that propylene oxide competes with propylene to be adsorbed on the same adsorptive center-Tin site on the surface of the catalyst and that the adsorbing capacity of the catalyst for propylene oxide is larger than that for propylene. Catalytic behavior for propylene epoxidation with H2 and O2 was tested in a micro-reactor. Under typical conditions, the selectivity for propylene oxide is over 87%. The TG curves show that PO successive oxidation cause carbon deposition on the active center and deactivation of the Au catalysts. Because the amounts of Tin site decrease significantly, and consequently the separation between Tin sites increases, the Au/TiO2-SiO2 catalyst is more stable than Au/TiO2.     

Selective photocatalytic oxidation of light alkanes over alkali-ion-modified V2O5/SiO2; kinetic study and reaction mechanism

Alkali-ion-modified silica-supported vanadium oxides are photocatalysts available in the field of photooxidation of light alkanes using molecular oxygen. The photooxygenated reaction was promoted over the catalyst under irradiation at steady state. Acetone formation on the photooxidation of propane was investigated over a rubidium-ion-modified silica-supported vanadium oxide that is the most effective catalyst. The kinetic analysis demonstrated that the rate-determining step is the reaction of propane on the lattice oxygen of the photoexcited VO4Rb species to yield the vanadium isopropoxide species. It was suggested that the photocatalytic active sites are occupied by photogenerated acetone during photoreaction at 333 K. Heating the photocatalyst bed drastically enhanced not only product yield but also the selectivity to propionaldehyde that is a minor product in the photooxidation at 333 K. The product distribution of photoassisted oxidation of propane was described by Boltzmann's distribution of stabilization energy of the intermediates: an isopropoxide-like one for the precursor of acetone and an n-propoxide-like one for the precursor of propionaldehyde.     

Boosting fuel cell performance with a semiconductor photocatalyst: TiO2/Pt-Ru hybrid catalyst for methanol oxidation

A hybrid carbon fiber electrode (CFE) consisting of TiO2 semiconductor photocatalyst and Pt-Ru catalyst has been developed to boost the performance of direct methanol fuel cells (DMFC). These two catalyst nanoparticles are deposited on opposite sides of the carbon fiber paper such that methanol oxidation is carried out catalytically on Pt-Ru and photocatalytically on TiO2 under UV-light irradiation. Since both catalysts carry out methanol oxidation independently, we observe an additive effect in the current generation. The carbon support fibers provide a large network to collect the electrons from both of these catalytic processes and thus assist in efficient current generation. In addition, TiO2 improves the performance of the Pt-Ru catalyst in dark, indicating possible surface area improvement or diminished poisoning effects. The concept of incorporating a photocatalyst provides new ways to minimize precious metal content and enhance the performance of DMFCs. At low catalyst loadings (0.15 mg/cm2) at 295 K, a 25% enhancement in the peak power density is observed upon illumination with light.     

FTIR spectroscopic study of titanium-containing mesoporous silicate materials

The surface acidity of different mesoporous titanium-silicates, such as well-organized hexagonally packed Ti-MMM, Ti-MMM-2, Ti-SBA-15, and amorphous TiO(2)-SiO(2) mixed oxides (aerogels and xerogels), was studied by means of FTIR spectroscopy of CO adsorbed at 80 K and CD(3)CN adsorbed at 293 K. The surface hydroxyl groups of mesoporous titanium-silicates with 2-7 wt % Ti revealed a Br?nsted acidity slightly higher to that of pure silicate. TiO(2)-SiO(2) xerogels revealed the highest Br?nsted acidity among the titanium-silicates studied. CO adsorption revealed two additional sites on the surface in comparison to pure silicate, characterized by nu(CO) from 2185 (high pressure) to 2178 (low pressure) cm(-1) and from 2174 (high pressure) to 2170 (low pressure) cm(-1). These bands are due to CO adsorbed on isolated titanium cations in the silica surrounding or having one Ti(4+) cation in their second coordination sphere and due to CO interactions with Ti-OH groups, respectively. CD(3)CN adsorption similarly revealed the existence of two additional sites, which were not detected for pure silicate: at 2289 cm(-1) due to CD(3)CN interaction with titanol groups and from 2306 (low pressure) to 2300 (high pressure) cm(-1) due to acetonitrile interaction with isolated framework titanium cations with probably one Ti(4+) cation in their second coordination shell. The spectroscopic results are compared with computational data obtained on cluster models of titanium-silicate with different titanium content. According to the IR data, the Ti accessibility on the surfaces for mesoporous titanium-silicates with similar Ti loading (2 wt %) was found to fall in the order TiO(2)-SiO(2) aerogel approximately TiO(2)-SiO(2) xerogel > Ti-MMM approximately Ti-MMM-2 > Ti-SBA-15. This order (except TiO(2)-SiO(2) xerogel) correlates with the catalytic activity found previously for titanium-silicates in 2,3,6-trimethylphenol oxidation with H(2)O(2).     

SO42-/TiO2-SiO2的制备及对甲基橙的光催化降解

0 引言 水中难降解有机物的治理已成为当今重要的环境问题,对新型高效水处理剂的需求也愈加迫切。多相光催化氧化已成为国内外治理污水的新技术,但常规二氧化钛半导体光催化剂的量子效率     

TiO2-Al2O3复合氧化物载体焙烧温度对Au-Pd催化剂加氢脱硫性能的影响

 采用溶胶-凝胶法制备了介孔TiO2-Al2O3复合氧化物载体,考察了载体的焙烧温度对负载型Au-Pd双金属催化剂加氢脱硫性能的影响,并采用X射线衍射、吸附吡啶的程序升温脱附、程序升温还原、红外光谱和N2物理吸附等技术对载体及催化剂进行了表征. 结果表明,不同温度焙烧的TiO2-Al2O3复合载体都具有介孔结构,其中773 K焙烧制得的TiO2-Al2O3复合载体的比表面积和孔容较大, B酸中心较多,以其为载体的Au-Pd 催化剂具有较好的加氢脱硫活性. 表征结果表明, 773 K焙烧制得的Au-Pd/TiO2-Al2O3催化剂中Au-Pd活性组分与载体的相互作用较强,催化剂上形成的AuxPdy合金的晶粒较小且数量较多,催化剂的酸量和活性组分的分散度较大,并且其上进行的加氢脱硫反应的活化能较低,这些因素均有利于催化剂活性的提高.     

(I(2))(n) encapsulation inside TiO(2): a way to tune photoactivity in the visible region

We report on the synthesis of nanovoid-structured TiO(2) material via a sol-gel route using titanium isopropoxide as precursor. The nanovoids are formed during the thermal treatment in air at 773 K. The surfaces of internal cavities are populated by the partial oxidation products of the organic part of the Ti precursor (CO(2), hydrogen carbonates, and residual isopropoxide groups). The thermal treatment in air at 773 K allows the maintainence, in the internal voids, of the encapsulated species. Addition of iodine in the synthesis procedure results in a new nanovoid-structured titanium oxide able to absorb light in the whole visible part of the electromagnetic spectrum. The origin of this absorption is attributed to the presence of (I(2))(n) adducts encapsulated in the nanocavities. These species coexist with partial combustion products of isopropoxide groups. Due to the protection of the TiO(2) walls, the (I(2))(n) adducts are not destroyed by thermal treatments in air. We have investigated whether the electron promoted in the excited state of the dye molecule (upon absorption of visible light from the (I(2))(n) adducts) can be injected into either the TiO(2) conduction band or some titanium-localized acceptor, followed by migration of the injected electron to the surface where it reduces adsorbed organic molecules. Preliminarily experiments conducted with sunlight show that the surface-specific efficiency of this process, tested by following the degradation of methylene blue, is about 10 times higher than that of the P25 commercial TiO(2) photocatalyst.     

Enhanced photocatalytic degradation of C.I. Basic Violet 2 using TiO2-SiO2 composite nanoparticles

In this report, TiO(2) -SiO(2) composite nanoparticles were prepared by the thermal hydrolysis method using titanium tetrachloride and tetraethylorthosilicate as TiO(2) and SiO(2) precursors, respectively. The prepared nanoparticles were characterized by X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption/desorption and UV-Vis diffuse reflectance spectroscopy (DRS). The results indicated that, in comparison with pure TiO(2), TiO(2)-SiO(2) composite nanoparticles had a higher thermal stability, which prevents phase transformation from anatase to rutile. In addition, the TiO(2)-SiO(2) nanoparticles had a higher specific surface area, larger pore volume, greater band gap energy and smaller crystallite size. Thus, the surface area of TiO(2)-40% SiO(2) composite nanoparticles was about 17 times higher than that of pure TiO(2) nanoparticles. The photocatalytic activity of TiO(2)-SiO(2) composite nanoparticles in the photodegradation of C.I. Basic Violet 2 was investigated. The photodegradation rate of Basic Violet 2 using TiO(2)-40% SiO(2) nanoparticles calcined at 600°C was much faster than that using pure TiO(2) and Degussa P25 TiO(2) by 10.9 and 4.3 times, respectively. The higher photoactivity of the TiO(2)-SiO(2) composite nanoparticles was attributed to their higher surface area, larger pore volume, greater band-gap energy and smaller crystallite size compared with pure TiO(2).     

Adsorption and photodegradation of dimethyl methylphosphonate vapor at TiO(2) surfaces

The adsorption and degradation of the nerve agent simulant dimethyl methylphosphonate (DMMP) over UV-irradiated TiO(2) powders and thin films has been investigated. Adsorption of vapor-phase DMMP on TiO(2) powder is characterized by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Photochemically assisted oxidation of adsorbed DMMP is carried out in situ by irradiation of samples in the DRIFTS accessory, giving kinetic data and information on specific site binding of DMMP and catalyst poisoning. Gas-phase intermediates from a static vapor phase reaction are identified by gas chromatography-mass spectrometry analysis, and surface-bound intermediates and products are analyzed by high-performance liquid chromatography-mass spectrometry, and ion chromatography of both aqueous and organic extractions from the TiO(2). Adsorbed DMMP is photodegraded in a stepwise fashion to give methylphosphonic acid, PO(4)(3-), H(2)O, and CO(2) as products. A proposed reaction pathway is consistent with a rapid degradation of DMMP but with extensive poisoning of the catalyst by surface-bound phosphonate products.     

Photocatalytic degradation of aniline at the interface of TiO2 suspensions containing carbonate ions

The degradation of aniline has been investigated using aqueous TiO2 suspensions containing carbonate ions as photocatalyst. The addition of carbonate to Degussa P-25 increased the number of active adsorption sites at its surface. For the TiO2 suspensions containing carbonate ions the intensity of adsorption of aniline increased to 6.9 x 10(2) from 5.5 x 10(2) mol(-1) dm(3) in case of bare TiO2 suspensions. This in turn results in the increased interfacial interaction of the photogenerated charge carriers with the adsorbed aniline and thus enhancing the rate of its photodecomposition to 6.5 x 10(-6) mol dm(-3) s(-1) compared to 2.7 x 10(-6) mol dm(-3) s(-1) in the absence of Na(2)CO(3). The maximum efficiency of this photocatalyst has been obtained upon addition of 0.11 mol dm(-3) of Na(2)CO(3) at pH 10.8. The photocatalytic action is understood by the simultaneous interaction of intermediates, *OH and CO*-(3), and their reactivity with aniline. Azobenzene, p-benzoquinone, nitrobenzene, and NH(3) have been identified as the major products of the photooxidation of aniline. Both the reactant and products have been followed kinetically. The photodegradation follows Langmuir-Hinshelwood Model. The mechanism of the occurring reactions has been analyzed and discussed. In the presence of Na(2)CO(3), 3 x 10(-3) mol dm(-3) of aniline could be photodegraded completely in about 6 h while all organic intermediates decomposed completely within about 10 h.     

Photocatalytic degradation of methyl orange over metalloporphyrins supported on TiO2 Degussa P25

The photocatalytic activity of meso-tetraphenylporphyrins with different metal centers (Fe, Co, Mn and Cu) adsorbed on TiO(2) (Degussa P25) surface has been investigated by carrying out the photodegradation of methyl orange (MO) under visible and ultraviolet light irradiation. The photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), diffuse reflectance UV (DRS-UV-vis) and infrared spectra. Copper porphyrin-sensitized TiO(2) photocatalyst (CuP-TiO(2)) showed excellent activity for the photodegradation of MO whether under visible or ultraviolet light irradiation. Natural Bond Orbital (NBO) charges analysis showed that methyl orange ion is adsorbed easier by CuP-TiO(2) catalyst due to the increase of induced interactions.     

Effect of calcination temperature on structure and performance of Ni/TiO2-SiO2 catalyst for CO2 reforming of methane

The influence of calcination temperature on the structure and catalytic behavior of Ni/TiO2-SiO2 catalyst, for CO2 reforming of methane to synthesis gas under atmospheric pressure, was investigated. The results showed that the Ni/TiO2-SiO2 catalyst calcined at 700 ℃ had high and stable activity while the catalysts calcined at 550 and 850 ℃ had low and unstable activity. Depending on the calcination temperature, one, two, or three of the following Ni-containing species, NiO, Ni2.44Ti0.72Si0.07O4, and NiTiO3 were identified by combining the temperature programmed reduction （TPR） and X-ray diffraction （XRD） results. Their reducibility decreased in the sequence： NiO〉Ni2.44Ti0.72Si0.07O4〉NiTiO3. It suggests that high and stable activities observed over the Ni/TiO2-SiO2 catalyst calcined at 700 ~C were induced by the formation of Ni2.44Ti0.72Si0.07O4 and smaller NiO species crystallite size.     

FTIR study of adsorption and surface reactions of N(CH3)3 on TiO2

Fourier transform infrared spectroscopy has been employed to investigate the N(CH3)3 adsorption, thermal stability, and photochemical reactions on powdered TiO2. N(CH3)3 molecules are adsorbed on TiO2 without dissociation at 35 degrees C and are completely desorbed from the surface at 300 degrees C in a vacuum. The CH3 rocking frequencies of N(CH3)3 on TiO2 are affected via the interaction between N(CH3)3 and TiO2 surface OH groups. In the presence of O2, adsorbed N(CH3)3 decomposes thermally at 230 degrees C and photochemically under UV irradiation. In the latter case with comparative (16)O2 and (18)O2 studies, CO2(g), NCO(a), HCOO(a), and surface species containing C=N or NH(x) functional groups are identified to be the photoreaction products or intermediates. In the presence of (18)O2, the main formate species formed is HC(16)O(18)O(a). As H2O is added to the photoreaction system, a larger percentage of adsorbed N(CH3)3 is consumed. However, in the presence of (18)O2 and H2O, the amount of HC(16)O(18)O(a) becomes relatively small, compared to HC(16)O(16)O(a). A mechanism is invoked to explain these results. Furthermore, based on the comparison of isotopic oxygens in the formate products obtained from CH3O(a) photooxidation in (16)O2 and (18)O2, it is concluded that the N(CH3)3 photooxidation does not generate CH3O(a) in which the oxygen belongs to TiO2.     

Localized Partial Oxidation of Acetic Acid at the Dual Perimeter Sites of the Au/TiO(2) Catalyst-Formation of Gold Ketenylidene

Chemisorbed acetate species derived from the adsorption of acetic acid have been oxidized on a nano-Au/TiO(2) (～3 nm diameter Au) catalyst at 400 K in the presence of O(2)(g). It was found that partial oxidation occurs to produce gold ketenylidene species, Au(2)═C═C═O. The reactive acetate intermediates are bound at the TiO(2) perimeter sites of the supported Au/TiO(2) catalyst. The ketenylidene species is identified by its measured characteristic stretching frequency ν(CO) = 2040 cm(-1) and by (13)C and (18)O isotopic substitution comparing to calculated frequencies found from density functional theory. The involvement of dual catalytic Ti(4+) and Au perimeter sites is postulated on the basis of the absence of reaction on a similar nano-Au/SiO(2) catalyst. This observation excludes low coordination number Au sites as being active alone in the reaction. Upon raising the temperature to 473 K, the production of CO(2) and H(2)O is observed as both acetate and ketenylidene species are further oxidized by O(2)(g). The results show that partial oxidation of adsorbed acetate to adsorbed ketenylidyne can be cleanly carried out over Au/TiO(2) catalysts by control of temperature.     

TiOx(x＜2)表面修饰Ni/TiO2-SiO2催化顺酐液相选择加氢合成γ-丁内酯

以TiO2-SiO2复合氧化物气凝胶为载体,制备了一系列Ni/TiO2-SiO2催化剂,并采用N2物理吸附-脱附、H2程序升温还原/脱附、X射线衍射及原位漫反射傅里叶变换红外光谱等技术对催化剂进行了表征,考察了载体中钛含量对催化剂结构、表面性质及其催化顺酐液相选择加氢合成γ-丁内酯反应性能的影响.结果表明,较小的Ni0...