An Intracavity-Triggered Passively-Switched Nd:YVO<Subscript>4</Subscript> Laser

We demonstrate an intracavity-triggered passively Q-switched Nd:YVO₄ laser within a diode-end-pumped configuration. We employ a Cr⁴⁺:YAG saturable absorber as the passive Q switch and an Nd:LiYF₄ (YLF) laser as the laser triggering of the Q-switched laser. Since we use the same Cr⁴⁺:YAG crystal and output coupler with the Nd:YVO₄ laser, the Cr⁴⁺:YAG Q switch is triggered inside the Nd:YLF laser cavity. As a result, the timing jitter in standard deviation of Nd:YVO₄ laser can be reduced to 16 ns.     

High-Pulse-Energy Passively <Emphasis Type="Italic">Q</Emphasis>-Switched 1,123 nm Laser with a Nd:GdYAG Mixed Garnet as Laser Medium

We demonstrate a diode-pumped passively Q-switched Nd:GdYAG mixed garnet laser at 1,123 nm. A Cr⁴⁺:YAG crystal with an initial transmission of 97% is used as the saturable absorber. The maximum average output power is 1.05 W at an absorbed pumping power of 8.12 W. A single-pulse energy can reach up to 78.9 μJ, with a corresponding pulse repetition rate of 13.3 kHz.     

A Single -Longitudinal-Mode Nd:Ce:YAG <Emphasis Type="Italic">Q</Emphasis>-Switched Laser Based on a Three-Plan Resonant Reflector

We present an efficient and compact passively Q-switched flash-lamp-pumped Nd:Ce:YAG singlelongitudinal-mode (SLM) laser system. With Cr⁴⁺:YAG as a saturable absorber, we design a three-plan resonant reflector for generating smooth SLM Q-switched pulses. We provide a theoretical calculation and optimization of the resonant reflector for improving the longitudinal-mode selection ability. We obtain a stable SLM output with a single-pulse energy of 10 mJ and a pulse width of 10.7 ns at 10 Hz. The near-diffraction-limited beam-quality parameter M² is less than 1.5. The system can operate with a repetition rate from 1 to 10 Hz. We achieve the stable laser operation with less than 3% fluctuation of the pulse energy within 10,000 shots.     

Doubly <Emphasis Type="Italic">Q</Emphasis>-Switched Nd:YAG Ceramic Laser

Using simultaneously both an acousto-optic (AO) modulator and a Cr⁴⁺:YAG saturable absorber in the cavity, we demonstrate for the first time the performance of a diode-pumped doubly Q-switched Nd:YAG ceramic laser. In contrast to purely acousto-optic Q-switched laser, this doubly Q-switched laser can generate shorter and more symmetric pulses. At an absorbed pump power of 10 W and a repetition rate of 20 kHz, the pulse width is compressed to 30 and 25 ns, respectively.     

<Emphasis Type="Italic">Q</Emphasis>-Switched Yb-Doped Fiber Ring Laser with a Saturable Absorber Based on a Graphene Polyvinyl Alcohol Film

We propose, design, and demonstrate a Q-switched ytterbium-doped fiber laser (YDFL) employing a thin graphene polyvinyl alcohol (PVA) film as a passive saturable absorber (SA). The graphene is synthesized by electrochemical exfoliation of graphite at room temperature in 1% sodium dodecyl sulfate (SDS) aqueous solution. Graphene flakes obtained from the process are mixed with PVA solution as the host polymer to produce a thin film, which acts as a passive Q-switcher in the YDFL ring cavity. The laser generates a stable pulse operating at a wavelength of 1,076.4 nm with a threshold pump power of 73.7 mW. At a maximum 980 nm pump power of 113.6 mW, the YDFL generates an optical pulse train with a repetition rate of 25.53 kHz and a pulse width of 10 μs. The maximum pulse energy of 50.9 nJ is obtained at a pump power of 109.9 mW. A higher-performance Q-switched YDFL is expected to be achieved with optimization of the graphene saturable absorber and the laser cavity.     

A Novel 1,066 nm Nd:Gd<Subscript>0<Emphasis Type="Italic">.</Emphasis>69</Subscript>Y<Subscript>0<Emphasis Type="Italic">.</Emphasis>3</Subscript>NbO<Subscript>4</Subscript> Passively <Emphasis Type="Italic">Q</Emphasis>-Switched Pulse-Burst Laser

We demonstrate for the first time a Cr⁴⁺:YAG passively Q-switched 1066 nm pulse-burst laser under 879 nm direct pump with a novel Nd:Gd_0.69Y_0.3NbO₄ crystal. The output laser characteristics with different pump repetition rates and different Cr⁴⁺:YAG initial transmission are studied. Without the Cr⁴⁺:YAG, we obtain a maximum output energy of 2.55 mJ at an absorbed pump energy of 5.79 mJ with the highest 48% slope efficiency. The pulse-burst laser contains a maximum of 7 pulses for a Cr⁴⁺:YAG initial transmission of 55% and a pump repetition rate of 1 kHz. The single-pulse energy and narrowest pulse width reach 160 μJ and 5.5 ns at 38.2 kHz, with a peak power of 32 kW.     

A Compact YAG/Nd:YAG/Cr:YAG Passively <Emphasis Type="Italic">Q</Emphasis>-Switched Pulse Burst Laser Pumped by 885 nm Laser Diode

We demonstrate a high-repetition-rate, short-pulse-width pulse burst laser from a compact 885 nm laser diode directly pumped by a passively Q-switched YAG/Nd:YAG/Cr:YAG laser. We investigate the output laser characteristics with different output transmissions and spot sizes of the pumping laser and compare these characteristics. After optimization, we achieve a shortest pulse width of 1.4 ns generated by a 1,064 nm pulse burst laser. The single-pulse energy reaches 239 μJ at 86.3 kHz, with a peak power of 117.2 kW.     

A High-Power,Long-Wavelength Infrared ZnGeP<Subscript>2</Subscript> Opo Pumped by a <Emphasis Type="Italic">Q</Emphasis>-Switched Tm,Ho:GdVO<Subscript>4</Subscript> Laser

We report a high-power, long-wavelength infrared ZnGeP₂ (ZGP) optical parametric oscillator (OPO) pumped by a Q-switched Tm,Ho:GdVO₄ laser. The wavelength tuning range of 7.8–9.9 μm is realized by rotating the external angle of the ZGP crystal. We obtain an output power over 30 mW across the whole wavelength range and achieve a 1.71 W output power at 8.08 μm by transmitting the OPO parameters, corresponding to an idler laser slope efficiency of 12.1%.     

Voltage-on-Type RTP Pockels Cell for <Emphasis Type="Italic">Q</Emphasis>-switch of an Er:YAG Laser at 1,617 nm

We report a resonantly diode-pumped electro-optic Q-switched Er:YAG laser operating at 1,617 nm using a voltage-on-type rubidium titanyl phosphate (RTP) Pockels cell as the modulator. The Er:YAG laser operates at a very stable Q-switching mode with a per pulse energy yield of 1.5 mJ and a pulse duration of 114 ns at 1 kHz PRF under an incident pump power of 21.6 W.     

A Tm:YLF End-Pumped Acousto-Optic <Emphasis Type="Italic">Q</Emphasis>-Switched Ho:YAG Laser

We report an acoustic Q-switched Ho:YAG laser end-pumped by a 1,908 nm Tm:YLF laser. The doping concentration of Ho:YAG crystal is 2 at.%, and dimensions ø5×20 mm. We measure the pulsedlaser output characteristics of the Ho:YAG laser at different repetition rates (RF). Under optimum experimental conditions, the high-power 2.1 μm output power reaches 4.17 W at a given pump power of 13.25 W and repetition frequency of 8.0 kHz. For a slope efficiency of 16.88%, the corresponding optical-to-optical conversion efficiency reaches 31.47%. We obtain a minimum single pulsed energy of 7.36 mJ and a pulse width of 52.8 ns at a pump power of 10.52 W and repetition rate of 0.5 kHz, with a peak power of 139 kW.     

Femtosecond Er<Superscript>3+</Superscript> fiber laser for application in an optical clock

The main elements needed for the realization of a compact femtosecond methane optical clock are developed and studied. A femtosecond laser system on an Er³⁺ fiber (λ = 1.55 μm) contains an oscillator, an amplifier, and a fiber with a relatively high nonlinearity in which the supercontinuum radiation is generated in the range 1–2 μm. In the supercontinuum spectrum, the fragments separated by an interval that is close to the methane-optical reference frequency (λ = 3.39 μm) exhibit an increase in intensity. The supercontinuum radiation is converted into the difference frequency in a nonlinear crystal to the range of the methane-reference frequency (λ = 3.3–3.5 μm), so that the frequency components of the transformed spectrum have sufficient intensities for the subsequent frequency-phase stabilization with respect to the methane reference. A system that stabilizes the pulse repetition rate of the femtosecond Er³⁺ laser is also employed. Thus, the repetition rate of the ultrashort pulses of the femtosecond fiber laser is locked to the methane reference. The pulse repetition rate is compared with the standard second. Thus, the scheme of an optical clock is realized.     

Low-temperature time-resolved VUV luminescence spectroscopy of SrF<Subscript>2</Subscript>: Er<Superscript>3+</Superscript> crystals

Time-resolved excitation and emission spectra of SrF₂: Er³⁺ upon selective excitation with synchrotron radiation in the VUV and ultrasoft x-ray ranges at T = 8 K were studied. The VUV luminescence of SrF₂: Er³⁺ derives from high-energy interconfiguration 4f¹⁰5d-4f¹¹ transitions in the Er³⁺ ion. The VUV emission spectrum revealed, in addition to the 164.5-nm band (millisecond-range kinetics), a band at 146.4 nm (with a decay time of less than 600 ps). The formation of excitation spectra for the f-f and f-d transitions in the Er³⁺ ion is discussed.     

Upconversion CW laser at 284 nm in a Nd:YAG-pumped double-cladding thulium-doped ZBLAN fiber laser

A successful continuous-wave (CW) ultraviolet (UV) laser in a Tm⁺³-doped ZBLAN fiber, operated at 284 nm (¹ I ₆ → ³ H ₆ transition of Tm⁺³) is demonstrated. The excitation uses a four-step upconversion scheme. The pump source is a Nd:YAG laser operated at 1.064 μm. A laser output power of 42 μW continuous wave was obtained for 590 mW of the launched pump power. The slope efficiency with respect to the launched pump power was measured to be 9%. Ultraviolet (at 365 nm) and visible (at 453 and 480 nm) radiation was also observed.     

Role of the nuclear and electromagnetic interactions in the coherent dissociation of the relativistic <Superscript>7</Superscript>Li nucleus into the <Superscript>3</Superscript>H + <Superscript>4</Superscript>He channel

The differential cross section in the transverse momentum Q and a total cross section of (31 ± 4) mb for the coherent dissociation of a 3-A-Ge V/c ⁷Li nucleus through the ³H + ⁴He channel have been measured on emulsion nuclei. The observed Q dependence of the cross section is explained by the predominant supposition of the nuclear diffraction patterns on light (C, N, O) and heavy (Br, Ag) emulsion nuclei. The contributions to the cross section from nuclear diffraction (Q ≤ 400 Me V/c) and Coulomb (Q ≤ 50 Me V/c) dissociations are calculated to be 40.7 and 4 mb, respectively.     

Dual-wavelength generation at the transverse mode locking in a diode-end-pumped passively Q-switched Nd:YLF/Cr<Superscript>4+</Superscript>:YAG laser

A dual-wavelength generation at 1047 and 1053 nm is implemented in a diode-endpumped Nd:YLF laser Q-switched by Cr:YAG. This generation is obtained by the tuning of the cavity length near the regions of the transverse-mode degeneracy.     

Thermal quenching of luminescence of BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals activated with Er<Superscript>3+</Superscript> and Tm<Superscript>3+</Superscript> ions

Thermal quenching of interconfigurational 5d-4f luminescence of Er³⁺ and Tm³⁺ ions in BaY₂F₈ crystals is studied in the temperature range of 330–790 K. The quenching temperatures are ~575 and ~550 K for Er³⁺ and Tm³⁺, respectively. It is shown that quenching of 5d-4f luminescence of Tm³⁺ ions is caused by thermally stimulated ionization of 5d electrons to the conduction band.     

Amplification of a <Emphasis Type="Italic">Q</Emphasis>-Switched Ho:GdVO<Subscript>4</Subscript> Oscillator in Thulium-Doped Large-Mode-Area Fiber

We report a high peak power, narrow linewidth, stable pulsed Ho:GdVO₄ amplifier based on thuliumdoped fiber, which produces 6.65 W average output power at 2,048 nm and 56.8 kW peak power with 11.7 ns pulse width at 10 kHz repetition rate. We use a simple Q-switched Ho:GdVO₄ laser as a seed laser and a thulium-doped fiber pumped by a 792 nm laser diode as an amplifier. The fiber amplifier provided 6.5 dB gain to the input signal. The spectral linewidth of the Ho:GdVO₄ amplifier remains < 0.5 nm with an M² beam quality of 1.36.     

Spectra of optical absorption and energy levels diagram of Er<Superscript>3+</Superscript> ions in bulk crystals of aluminum nitride

The absorption spectra of the Er³⁺ ions embedded in the AlN matrix have been investigated. The admixture of erbium was introduced in bulk AlN crystals by diffusion. The absorption lines, which are associated with the intraconfigurational electronic f–f-transitions from the ground ⁴ I _15/2-state to the levels of ion Er³⁺ excited states have been observed in the spectral range of 370–700 nm. The transitions to the state levels ⁴ F _9/2, ² H _11/2, ⁴ F _7/2, ⁴ F _5/2, ² H _9/2, and ⁴ G _11/2 have been investigated in detail at the temperature T = 2 K. The number of the observed lines for these transitions coincides with the theoretically possible one for the electronic f–f-transitions in the ions Er³⁺, which are in the crystal field with the symmetry below cubic. The narrowness of the observed lines and their number convincingly testify the replacement of preferably one regular crystalline position by erbium ions. The implementation of Er³⁺ in the Al³⁺ position with the local symmetry C _3v appears the most probable. The energy positions of the levels of excited states for the investigated transitions have been determined. The diagram of the Er³⁺ ion energy levels in the AlN crystals has been built.     

Study of absorption spectra of Er<Superscript>3+</Superscript> in KTaO<Subscript>3</Subscript> crystals

The first results of the study of optical absorption spectra of KTaO₃: Er³⁺ crystals are presented. In the 350–660-nm region, lines are observed deriving from intraconfigurational electronic transitions from the ⁴ I _15/2 ground state to levels of the ⁴ F _9/2, ⁴ S _3/2, ² H _11/2, ⁴ F _7/2, ⁴ F _5/2(⁴ F _3/2), ² G _9/2, and ⁴ G _11/2 excited states of the Er³⁺ ions. A comprehensive study of transitions to the ⁴ F _9/2, ⁴ S _3/2, ² H _11/2, and ⁴ F _7/2 levels at 77 K is carried out. The number of lines observed for the above transitions fits the theoretically possible number for ?-? electronic transitions in Er³⁺ ions in the cubic crystal field. In the case of a differently charged substituted ion, this situation occurs only under nonlocal impurity charge compensation. The energies of the excited state levels for the transitions under study are determined.     

Line shape of <Superscript>57</Superscript>Co sources exhibiting self absorption

The effect of selfabsorption in Mössbauer sources is studied in detail. Spectra were measured using an old ⁵⁷ C o/R h source of 74M B q activity with an original activity of ca. 3.7G B q and a 0.15G B q ⁵⁷ C o/α ? F e source magnetized by an in-plane magnetic field of 0.2 T. The ⁵⁷ C o/α ? F e source of a thickness of 25 μ was used both from the active and the inactive side giving cause to very different selfabsorption effects. The absorber was a single crystal of ferrous ammonium sulphate hexahydrate (FAS). Its absorption properties were taken over from a detailed study (Bull et al., Hyperfine Interact. 94(1–3), 1; Spiering et al. 2). FAS (space group P21/c) crystallizes as flat plates containing the (\(\overline {2}\)01) plane. The γ-direction was orthogonal to the crystal plate. The ⁵⁷ C o atoms of the ⁵⁷ C o/R h source were assumed to be homogeneously distributed over a 6μ thick Rh foil and to follow a one dimensional diffusion profile in the 25 μ Fe-foil. The diffusion length was fitted to 10 μ. The theory follows the Blume-Kistner equations for forward scattering (Blume and Kistner, Phys. Rev. 171, 417, 3) by integrating over the source sampled up to 128 layers.