Studies on the ageing of a magnesium-strontium nitrate pyrotechnic composition using isothermal microcalorimetry and thermal analysis techniques

The ageing behaviour of a pyrotechnic composition containing equal parts by mass of magnesium and strontium nitrate has been followed by isothermal microcalorimetry. The measurements were carried out on the samples at 50 °C and 65% relative humidity in air using closed ampoules. The results have been compared to those obtained for magnesium powder under the same conditions. Following an initial induction period, the pyrotechnic compositions reacted at a much faster rate than magnesium powder alone. The main reaction products were found to be magnesium hydroxide and strontium nitrite; the amounts formed have been correlated with the cumulative heats of ageing. In addition, the influence of the ageing process on the pyrotechnic reaction has been studied by high temperature differential scanning calorimetry (DSC) and by modulated temperature DSC.     

Use of isothermal microcalorimetry in pharmaceutical preformulation studies

Excipient compatibility of a new chemical entity was assessed using an isothermal microcalorimeter. Mixtures of an active pharmaceutical ingredient with a primary amine group and excipients were prepared in a 1:1 ratio and compatibility monitored by exposing to 50, 60 and 70°C in presence of 200 mL of water. The new chemical entity, a primary amine, reacted with reducing sugars such as lactose and resulted in a brown discoloration. This reaction is the Maillard type condensation reaction between amines and reducing sugars. The rate of reaction was dependent on the temperature with rapid degradation at higher temperatures. No other incompatibility was apparent between the primary amine and other excipients This revised version was published online in July 2006 with corrections to the Cover Date.     

Compatibility and stability tests of risperidone with soft-drinks by isothermal titration microcalorimetry

Isothermal titration microcalorimetry has been applied to investigate the compatibility testing of risperidone oral solution with soft-drinks and the interaction with tea tannin such as (–)-epigallocatechin, (–)-epicatechin, theaflavin and their gallates. In aqueous solution, risperidone was exothermically bound to tea tannin with binding affinity (10³–10⁴ M^–1), small enthalpy and entropy changes reflecting van der Waal’s interaction to form an insoluble complex at 1:1 molar ratio. The heat effect of risperidone titrated into soft-drinks containing tannin was exothermic and proportional to the quantity of the complex. While, no significant heat effect was found for risperidone titrated into a pet-bottled water and an infusion of parched barley without tea tannin. These results were agreed with stability testing of risperidone in some soft-drinks by HPLC method.     

Potential applications of microcalorimetry for the study of physical processes in pharmaceuticals

In calorimetry, the heat-flow to or from a sample is measured as a function of time (isothermal calorimetry) or temperature (scanning calorimetry). The technique is not dependent on the physical form of the sample and is usually non-destructive (exceptions include temperature-induced irreversible phase transitions and thermal decomposition). The inherent sensitivity of modern instruments allows measurements on the micro-Watt scale. Calorimetry is highly suited to the study of pharmaceutical systems because small sample masses are usually required and the technique is very sensitive to changes induced by, for instance, formulation or processing. It is the purpose of this review to show applications of both isothermal and scanning calorimetry in the field of physical and bio-physical pharmacy. Potential applications include studies of physical stability, excipient compatibility, chemical stability and the study of the potential interactions of and between macromolecules such as lipids, surfactants, and nucleic acids.     

An investigation of strontium nitrite and its role in the ageing of the magnesium-strontium nitrate pyrotechnic system using isothermal microcalorimetry and thermal analysis techniques

A sample of strontium nitrite has been synthesised and thermally characterised to investigate its role in the ageing of magnesium-strontium nitrate pyrotechnic compositions in the presence of water vapour. Studies by isothermal microcalorimetry show that the addition of strontium nitrite to a 50% magnesium-50% strontium nitrate composition eliminated the induction reaction normally observed in closed ampoule studies in air at 50 °C and relative humidities in the range 65-69%.     

Rapid and efficient screening of adsorbent for oligopeptide using molecular docking and isothermal titration calorimetry

A rapid and efficient method based on molecular docking and isothermal titration calorimetry (ITC) was developed to identify effective adsorbents for the target peptide Ser‐Glu‐Ala‐Asp‐His (SEADH). Preliminary screening of five candidate adsorbents using molecular docking revealed that three suitable structures (A1, A2, and A3) either with or without coordination of Zn²⁺ should be effective. The three selected structures were then prepared and further screened by evaluating their affinities for the peptide SEADH using ITC. The screening results revealed that the adsorbent A2 coordinated with Zn²⁺ was the best adsorbent, and subsequent static adsorption experiments confirmed the reliability of the screening method. Further ITC analysis, combined with molecular docking, was performed to provide the possible adsorption mechanism.     

Using isothermal microcalorimetry for the prediction and testing of long-term properties of materials and products

The use of isothermal microcalorimetry (MC) as a sensitive monitor for slow reactions is demonstrated in a number of examples. In Example 1 the spontaneous decomposition of a nitrate ester propellant is studied and the absolute degradation rate estimated. Example 2 illustrates how MC can be used for comparing the rate of oxidative ageing at different O₂ concentrations. Synergetic effects between oxygen and moisture in accelerated ageing of nitrile rubber are evaluated from a so-called 4-point test in Example 3. The last example shows a simple MC technique for rapid determination of moisture permeability through a polymeric sealant.     

Solid-state reactions from isothermal heat conduction microcalorimetry theoretical approach and evaluation via simulated data

Several recent publications from this laboratory have reported developments in the capacity to calculate thermodynamic and kinetic parameters, such as rate constant, enthalpy, order of reaction, from isothermal micro-calorimetric data. To date these developments have all been associated with the calculation of the desired parameters from solution phase reactions. This paper furthers these developments to a theoretical consideration of solid-state reactions and the calculation of the values for the rate coefficient, k, the fitting parameters m and n, the total number of joules released over the lifetime of reaction, Q, and hence either the specific enthalpy or the molar enthalpy of reaction, H. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preformulation compatibility studies of etamsylate and fluconazole drugs with lactose by DSC

Chemical compatibility of two drugs, namely, etamsylate and fluconazole was studied with lactose as excipient, employing differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques. The DSC patterns recorded for the mixtures of both the drugs with the common excipient (lactose) indicated that fluconazole as well as etamsylate were incompatible with lactose at high temperatures. X-ray diffraction patterns recorded for pure drugs and lactose and the mixtures of individual drugs with lactose prepared at room temperature by intimate grinding of the components revealed incompatibility of both the drugs with lactose also at room temperature. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermodynamics of interaction between sodium bis(2‐ethylhexyl) sulfosuccinae and polymers in aqueous solutions by isothermal titration microcalorimetry

The interactions between sodium bis(2‐ethylhexyl) sulfosuccinae (AOT) and two nonionic water‐soluble polymers, including polyvinyl pyrrolidone (PVP) and polyethylene glycol (PEG) have been investigated by using isothermal titration microcalorimetry in aqueous solutions at 298.15 K. The results show that the critical aggregation concentration, which corresponding to the first turning point in the curve of experimental interaction heat versus concentration of the surfactant, is lower than the critical micellar concentration (cmc), confirming the existence of polymer‐surfactant interactions. The value of cac is not sensitive to the relative amount of polymer in low concentration range of the polymer. The mono‐layer saturated adsorption concentration, which corresponding to the second turning point, rises as the polymer concentration is increased. The interaction between PVP and AOT is stronger than that between PEG and AOT. The results also indicate that the aggregation of AOT in water and polymers solutions is entropically driven. The observed thermal effects have been interpreted in terms of the interactions of the polymer molecules with AOT monomers or the molecular clusters. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 275–283, 2006     

Use of isothermal microcalorimetry in pharmaceutical preformulation studies,Part II. Amorphous phase quantification in a predominantly crystalline phase

Low amounts of amorphous phase present in predominantly crystalline powders were quantified by using various analytical techniques with an emphasis on the use of Isothermal Perfusion Microcalorimetry. The amorphous phase was plasticized using ethanol vapor and enthalpy of re-crystallization of amorphous phase was used for generation of a calibration curve. Amorphous content as low as 5% was quantified using this technique. Although baseline noise was very low, additional processes occurring during re-crystallization confounded quantification of lower amorphous fractions. This revised version was published online in July 2006 with corrections to the Cover Date.     

Kinetics and enthalpy measurements of interaction between beta-amyloid and liposomes by surface plasmon resonance and isothermal titration microcalorimetry

The objective of this research is to understand the interaction mechanism of β-amyloid (Aβ) with cell and were basically divided into two parts. The first part focused on the time-dependent structural changes of Aβ (1-40) by circular dichroism (CD) spectroscopy, thioflavin T (ThT) fluorescence assay, and atomic force microscopy (AFM). The second part emphasized the kinetics and enthalpy of interaction between Aβ (1-40) and liposome by surface plasmon resonance (SPR) and isothermal titration microcalorimetry (ITC). Results obtained from CD, ThT and AFM confirmed the formation of 1 μm fibril after single day incubation. The driving force of kinetic interaction between Aβ and liposomes was revealed by SPR to be electrostatics. Further studies indicated that fresh Aβ has high GM1 affinity. Besides, addition of cholesterol to the liposome could alter membrane fluidity and affect the interactions of fresh Aβ with liposomes especially in the amount of Aβ absorbed and preserving the structure of liposome after adsorbing. Hydrophobicity was found to be the driving force leading to the interaction between Aβ fibrils and liposomes. These reactions are endothermic as supported by ITC measurements. When the composition of liposomes is zwitterionic lipids, the interaction of Aβ with liposomes is predominantly hydrophobic force. In contrast, the driving force of interaction of charged lipids with Aβ is electrostatic.     

Application of the Avrami, Tobin, Malkin, and Urbanovici–Segal macrokinetic models to isothermal crystallization of syndiotactic polypropylene

Various kinetic equations, namely the Avrami, Tobin, Malkin, and Urbanovici–Segal models, have been applied to describe the kinetics of primary crystallization from the melt state of syndiotactic polypropylene (s-PP) under isothermal conditions. Analysis was carried out using a data-fitting procedure, in which the experimental data were fitted directly to each model using a non-linear multi-variable regression program. The results suggested that the experimental data of s-PP can be best described by the Urbanovici–Segal model, followed by the Avrami, Malkin, and Tobin models, respectively.     

Feasibility of using isothermal microcalorimetry to evaluate the physical stability of amorphous nifedipine and phenobarbital

Feasibility of microcalorimetry to evaluate the physical stability of amorphous drugs was studied. Amorphous forms of nifedipine and phenobarbital were prepared by melting and subsequent cooling in a differential scanning calorimetry (DSC) sample pan, and their heats of crystallization were monitored by isothermal microcalorimetry. The time required for 10% of the amorphous drug to crystallize (t₉₀), a direct measure of the crystallization rate, could be obtained from a single microcalorimetric trace of the amorphous nifedipine or phenobarbital. The t₉₀ values were also determined by conventional storage studies in which the heat of crystallization was determined by DSC. The t₉₀ values obtained by microcalorimetry were consistent with those obtained by DSC, within experimental error, indicating that microcalorimetry is a useful method for evaluating the physical stability of amorphous drugs.     

Studies on the binding of paeonol and two of its isomers to human serum albumin by using microcalorimetry and circular dichroism

Interactions of paeonol and two of its isomers with human serum albumin (HSA) in buffer solutions (pH 7.0) have been investigated by calorimetry and circular dichroism. Heats of the interactions have been determined with isothermal titration microcalorimetry at 298.15 K. Data process has been based on the supposition that there are several independent classes of binding sites on each HSA molecule for molecules of each one of the drugs. The results obtained by using this supposition combined with Langmuir adsorption model show that there are two classes of such binding sites. The binding constant, changes of enthalpy, entropy, and Gibbs free energy are obtained, which show that the two classes of binding are mainly driven by enthalpy except that the first-class binding of Ace is predominantly driven by entropy. On the same class of binding site, the negative value of binding enthalpy decreases in the order of Pae, Hma, and Ace. The difference of thermodynamic data is caused by the different locations of substituent groups on aromatic benzene ring of guest molecules. Circular dichroism (CD) spectra show that the three isomers change the secondary structure of HSA. These results indicate that the interaction includes contributions of the binding and the partial change of molecular structure of HSA induced by the three isomers.     

Stability and compatibility study on enalapril maleate using thermoanalytical techniques

This paper demonstrates the application of thermal analysis in compatibility and stability studies between an ACE inhibitor (enalapril maleate) and excipients. The results have helped to elucidate the reason of a stability problem observed during the storage of enalapril maleate tablets. Incompatibility between enalapril maleate and colloidal silicon dioxide was detected. Besides, it was confirmed that the reaction between enalapril maleate and NaHCO₃ increases the thermal stability of the drug. This study supports the importance of using thermoanalytical methods in the development of pharmaceuticals.     

Interaction study between pefloxacin mesilate and some diluents using DSC supported with isothermal method

The present investigation was carried out to screen compatibility of some diluents with pefloxacin mesilate using differential scanning calorimetry (DSC), isothermal stability studies, along with stability studies in liquid state and to assign relative ranking to diluents. Compatibility was predicted with MCC101, MCC102, DCP anhydrous, Emcompress, while melting endotherm of drug was lost in admixtures of dextrose anhydrous, Pearlitol, Lactopress spray dried, Lactochem fine powder and Lycatab indicating possibility of interaction. Enthalpy changes were used for relative ranking of diluents.     

Isothermal titration microcalorimetric method for studying the combined ligand binding with application to the binding of ethylurea and (N,N)dimethylurea on urease

A simple, novel method was introduced for determining equilibrium constants and enthalpies of binding of two different competitive ligands on a macromolecule by isothermal titration microcalorimetry technique. This method was applied to the simultaneous binding of ethylurea (I) and (N,N)dimethylurea (X), on jack-bean urease at pH 7.0 (tris-base; 30 mM) at 27°C. The dissociation equilibrium constants measured by this method were markedly consistent with inhibition constants obtained from assay of enzyme activities in the presence of I and X.     

A predictive, simple and rapid method for thermodynamic study on the binding of copper ion with Alzheimer''s amyloid β peptide

The interaction of CuC12 to the first 16 residues of the Alzbeimer's amyliod β peptide, Aβ(1-16) was studied by isothermal titration calorimetry at pH 7.2 and 37 ℃ in aqueous solution.