Rapid determination of banned Sudan I in foodstuffs using a mesoporous SiO2 modified electrode

Rapid determination of Sudan I in foodstuffs is very important because it was found to be a carcinogen and its use in the food industry was banned. A rapid, sensitive, and convenient electrochemical method was developed for the determination of Sudan I based on the distinctive properties of mesoporous SiO2. The electrochemical responses of Sudan I were investigated. A sensitive oxidation peak was observed for Sudan I, and the peak currents greatly increased at the mesoporous SiO2-modified electrode, which can be attributed to its large surface area and high accumulation efficiency. The effects of pH, amount of mesoporous SiO2, scan rate, accumulation potential, and time were examined on the oxidation signals of Sudan I. The linear range was from 4.00 x 10(-8) to 2.00 x 10(-5) M, and the LOD was 7.50 x 10(-9) M. The newly developed method was successfully used to detect and quantify Sudan I in hot chili powder and juice samples.     

介孔炭/纳米金修饰玻碳电极的制备及其应用研究

制备了介孔炭/纳米金修饰玻碳电极,并对对苯二酚(HQ)在该修饰电极上的电化学行为进行了研究。与HQ在纯介孔炭材料修饰玻碳电极上的电化学响应相比,HQ在该修饰电极上的氧化峰和还原峰电流均大大增加,表明纳米金与介孔炭复合后对HQ具有良好的催化作用。HQ在该修饰电极上经过富集后,峰电流明显增大。采用循环伏安法对HQ电化学行为进行研究,结果表明,HQ在3.0×10-8~1.0×10-6mol/L和1.0×10-6~1.0×10-4mol/L浓度范围内与峰电流呈良好的线性关系,据此建立了检测HQ的电化学分析方法。该方法的相对标准偏差为0.69%,检出限(S/N=3)为1.0×10-8mol/L,具有较高的稳定性和灵敏度。     

用聚(L-蛋氨酸)/纳米金修饰玻碳电极同时灵敏检测多巴胺和尿酸简

A novel electrochemical sensor was fabricated by electrodeposition of gold nanoparticles on a poly(L-methionine) (PMT)-modified glassy carbon electrode (GCE) to form a nano-Au/PMT composite-modified GCE (nano-Au/PMT/GCE). Scanning electron microscopy and electrochemical techniques were used to characterize the composite electrode. The modified electrode exhibited considerable electrocatalytic activity towards the oxidation of dopamine (DA) and uric acid (UA) in phosphate buffer solution (pH = 7.00). Differential pulse voltammetry revealed that the electrocatalytic oxidation currents of DA and UA were linearly related to concentration over the range of 5.0×10^-8 to 10^-6 mol/L for DA and 7.0×10^-8 to 10^-6 mol/L for UA. The detection limits were 3.7×10^-8 mol/L for DA and 4.5×10^-8 mol/L for UA at a signal-to-noise ratio of 3. According to our experimental results, nano-Au/PMT/GCE can be used as a sensitive and selective sensor for simultaneous determination of DA and UA.     

Amperometric determination of glutathione and cysteine on a Pd-IrO(2) modified electrode with high performance liquid chromatography in rat brain microdialysate

A Pd/IrO(2) co-electrodeposited glassy carbon electrode was prepared and the electrochemical behavior of glutathione (GSH) at this chemically modified electrode (CME) has been studied by cyclic voltammetry (CV). The results indicated that the modified electrode efficiently exhibited electrocatalytic oxidation for GSH with relatively high sensitivity, stability, and long-life. Coupled with high-performance liquid chromatography (HPLC), the Pd/IrO(2) modified electrode was utilized for the electrochemical detection (ECD) of the thiocompounds, glutathione and cysteine (Cys). The peak currents were linear with the substance concentrations in the range of 1.0 x 10(-5) mol L(-1) to 8.0 x 10(-4) mol L(-1) for GSH and 4.0 x 10(-6) mol L(-1) to 2.0 x 10(-4) mol L(-1) for Cys. The detection limits were 2.0 x 10(-6) mol L(-1) for GSH and 5.0 x 10(-7) mol L(-1) for Cys with S/N of 3. The method has been successfully applied to assess the contents of GSH and Cys in rat brain microdialysates.     

Simultaneous electrochemical determination of xanthine and uric acid at a nanoparticle film electrode

A sensitive electrochemical method was developed for simultaneous determination of uric acid (UA) and xanthine (XA) at a glassy carbon electrode modified with multi-wall carbon nanotubes (MWNTs) film. The oxidation peak currents of UA and XA were increased at the MWNTs film electrode significantly. The experimental parameters, which influence the peak currents of UA and XA, such as the amount of MWNTs on the glassy carbon electrode, the pH of the solution, accumulation time, and scan rate, were optimized. Under optimum conditions, the peak currents were linear to the concentration of UA over the wide range from 1 x 10(-7) mol L(-1) to 1 x 10(-4) mol L(-1) and to that of XA over the wide range from 2 x 10(-8) mol L(-1) to 2 x 10(-5) mol L(-1). The interferences studies showed that the MWNTs-modified electrode exhibited excellent selectivity in the presence of ascorbic acid, dopamine, and hypoxanthine. The proposed procedure was successfully applied to detect UA and XA in human serum without any preliminary treatment.     

Capillary electrophoresis/electrochemical detection system with on-line deoxygenation

A capillary electrophoresis (CE)/electrochemical detection system with on-line deoxygenation was developed, consisting of a deoxygenation injector, a deoxygenation protector, and an electrochemical detection cell. When the system was utilized for 60 min, the steady-state current of oxygen detected could be dropped to 3% of the original value for the gold/mercury amalgam electrode and to 8% of the original value for the gold electrode, and the limit of detection could be decreased two orders of magnitude for the reducible analytes such as TI+ (from 3.1 x 10-5 mol/L to 8.0 x 10-7 mol/L) and metronidazole (from 3.8 x 10-5 mol/L to 4.0 x 10-7 mol/L).     

Electrochemical behaviors of adrenaline at acetylene black electrode in the presence of sodium dodecyl sulfate

The electrochemical behaviors of adrenaline at the acetylene black electrode in the presence of sodium dodecyl sulfate (SDS) were investigated by cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The results indicated that the electrochemical responses of adrenaline were apparently improved by SDS, due to the enhanced accumulation of protonated adrenaline via electrostatic interaction with negatively charged SDS at the hydrophobic electrode surface. This was verified by the influences of different kinds of surfactants on the electrochemical signals of adrenaline. The electrochemical parameters of the adrenaline oxidation were explored by chronocoulometry. Under optimal working conditions, the oxidation peak current at 0.57 V was proportional to adrenaline concentration in the range of 5.0x10(-8) to 7.0x10(-6) mol/L, with a low detection limit of 1.0x10(-8)mol/L for 70s accumulation by differential pulse voltammetry (DPV). This method was applied to determine adrenaline in the hydrochloride injection sample. The results are satisfying compared with that by the standardized method of high performance liquid chromatography (HPLC).     

基于SiO2纳米粒子固定辣根过氧化物酶的生物传感器

制备了尺寸均一的SiO2纳米粒子(60nm),并将其用于固定辣根过氧化物酶.以儿茶酚为电子媒介体制得的H2O2传感器的检测范围为1.7×10-7～1.9×10-5mol/L,检出限为8.3×10-8mol/L.达到95%稳态电流所用时间少于10s.该传感器的米氏常数为7.8μmol/L,表明所固定的酶具有较高的生物活性.     

Anodic stripping voltammetric determination of mercury by use of a sodium montmorillonite-modified carbon-paste electrode

A sodium montmorillonite (SWy-2)-modified carbon-paste electrode has been examined for determination of trace levels of mercury. Because of its strong cation-exchange and adsorptive characteristics, SWy-2 greatly improves the sensitivity of determination of Hg(2+). Hg(2+) is preconcentrated and reduced on the modified electrode surface at -0.40 V and then stripped from the electrode surface during the positive potential sweep. The conditions used for determination, e.g. supporting electrolyte, pH, amount of SWy-2, accumulation potential, and accumulation time, were optimized. The peak current was linearly dependent on the concentration of mercury from 1 x 10(-9) to 5 x 10(-7) mol L(-1). The detection limit (signal-to-noise ratio=3) was 1 x 10(-10) mol L(-1) after accumulation for 6 min. When the SWy-2-modified carbon-paste electrode was used to detect mercury in water samples the average recovery was 101.11%.     

Voltammetric determination of cadmium(II) using a chemically modified electrode

An 1-(pyridylazo)-2-naphthol modified glassy carbon electrode has been investigated as sensor for the measurement of trace levels of Cd2+. Cd2+ is deposited on the surface of a PAN modified glassy carbon electrode at -1.10 V (vs. SCE) via forming Cd2+-PAN and subsequent reduction at the electrode. In the following step, Cd-PAN is oxidized, and voltammograms are recorded by scanning the potential in a positive direction. Calibration plots were found to be linear in the range 2 x 10(-8) mol/L to 8 x 10(-7) mol/L. The detection limit was 5 x 10(-10) mol/L, and the coefficient of variation, determined on one single electrode at a concentration of 5 x 10(-7) mol/L, was calculated to be 3.2% (n = 5). Using this new kind of modified electrode, trace levels of Cd(II) in water samples were determined; the average recovery was calculated to be 98.78%.     

Electrochemical behavior and electrocatalytic study of the methylene green coated on modified silica gel

The electrochemical behavior of methylene green (MG) adsorbed on a silica surface modified with niobium oxide (SN) was investigated, using modified carbon paste electrodes. It was also used in an electrocatalytic study of NADH oxidation. The electrode showed a high stability attributed to the presence of SN, which avoids the leaching of the mediator from the electrode surface. The formal potential (E(0')) of the adsorbed MG was -35 mV vs SCE, showing a shift of 30 mV toward more positive potential values, compared to the MG dissolved in aqueous solution. This shift was assigned to the interaction between the basic nitrogen of MG and the acid sites of SN. The variation of the solution pH between 4 and 8 did not affect the stability nor the formal potential. However, for solution pH lower than 4 the formal potential was affected by the acidity of the medium. The electrocatalytic oxidation of NADH at the electrode was investigated. In the solution pH between 5 and 8 the electrocatalytic activity remained almost constant, giving a response signal of 13.3 nA L micromol(-1) cm(-2) and a K(Mapp) of 1.4 x 10(-5) mol L(-1). The electrode gave a linear response range between 5.0 x 10(-4) and 4.0 x 10(-3) mol L(-1) NADH concentration at pH 7.0 at an applied potential of 50 mV vs SCE. Applying a flow injection analysis system, the electrode showed a better analytical performance for NADH detection, presenting a linear response range between 6.0 x 10(-5) and 1.0 x 10(-3) mol L(-1), with an analytical frequency of 30 determinations/h, a detection limit of 8.2 x 10(-6) mol L(-1), and a precision for 25 replicates of 1% expressed as a relative standard deviation.     

A high-sensitive amperometric hydrogen peroxide biosensor based on the immobilization of hemoglobin on gold colloid/L-cysteine/gold colloid/nanoparticles Pt-chitosan composite film-modified platinum disk electrode

A hemoglobin (Hb)/gold colloid (nano-Au)/L-cysteine (L-cys)/nano-Au/nanoparticles Pt (nano-Pt)-chitosan (CHIT) composite film-modified platinum disk electrode (abbreviated to modified electrode) has been prepared to construct a biosensor for determination of H(2)O(2). The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The morphologies of different composite film were investigated with scanning electron microscopy (SEM) and the element of composite film was investigated with X-ray photoelectron spectroscopy (XPS). Analytical parameters such as pH and temperature were also studied. The linear range for the determination of H(2)O(2) is 1.4 x 10(-7) to 6.6 x 10(-3)mol/L with a detection limit of 4.5 x 10(-8)mol/L (S/N=3). The sensor achieved 95% of the steady-state current within 10s. The sensor exhibited high sensitivity (17.62 microA/(mmol L)), selectivity and stability. The method is applied to the determination of H(2)O(2) with satisfactory results.     

Electrochemistry and voltammetric determination of colchicine using an acetylene black-dihexadecyl hydrogen phosphate composite film modified glassy carbon electrode

The electrochemical behavior of colchicine at an acetylene black-dihexadecyl hydrogen phosphate (denoted as AB-DHP) composite film coated glassy carbon electrode (GCE) was investigated using cyclic voltammetry (CV), linear sweep voltammetry (LSV) and differential pulse voltammetry (DPV). Compared with the poor electrochemical signal at the unmodified GCE, the electrochemical response of colchicine at the AB-DHP film modified GCE was greatly improved, as confirmed from the significant peak current enhancement. The remarkable peak current enhancement indicates that the AB-DHP modified GCE has great potential in the sensitive determination of colchicine. Thus, all the experimental conditions, which influence the electrochemical response of colchicine, were studied and the optimum conditions were achieved. Finally, a sensitive and simple voltammetric method with a good linear relationship in the range of 1.0 x 10(-7) approximately 4.0 x 10(-5) mol/L, was developed for the determination of colchicine. The detection limit of colchicine was also examined and a low value of 4.0 x 10(-8) mol/L for 4-min accumulation was obtained (S/N=3). This electrode was successfully applied to detect colchicine in human urine samples.     

Electrochemical behavior of thiamine on a self-assembled gold electrode and its square-wave voltammetric determination in pharmaceutical preparations.

The electrochemical behavior of thiamine on a self-assembled electrode of L-cysteine (Cys/SAM/Au) has been investigated and Cys/SAM/Au can be used to detect thiamine using square-wave voltammetry (SWV). At pH 11.40 Britton-Robinson buffer, thiamine exhibits a well-defined anodic peak on Cys/SAM/Au. Under the optimized conditions, the anodic peak current of SWV was linear with the content of thiamine in the range of 1.1 x 10(-8) - 2.2 x 10(-6) mol/L; the detection limit was 5.5 x 10(-9) mol/L. The method was successfully applied to the determination of thiamine in pharmaceutical preparations.     

Electrochemical detection of parathion at a glassy-carbon electrode modified with hexadecane

A modified electrode, based on a hexadecane (C(16))-coated glassy-carbon electrode (GCE) has been developed for the determination of parathion. The electrochemical behavior of parathion was investigated by cyclic voltammetry (CV). The peak potential and peak current were found to depend on the supporting electrolyte and the pH of the buffer solution. The reduction currents for parathion were proportional to parathion concentration over the range 8x10(-8)-2x10(-5) mol L(-1). The detection limit was 2x10(-8) mol L(-1) parathion for an accumulation time of 30 s. The effects of organic and inorganic species on the determination of parathion were also studied. A procedure was developed to extract parathion from spiked soil samples using a mixture of dichloromethane and acetone as the extraction solvent. The complete extraction and analytical procedure are simple, inexpensive and rapid. Parathion was determined in a soil sample by use of linear scan voltammetry (LSV).     

Gold nanoparticles-enhanced bisphenol A electrochemical biosensor based on tyrosinase immobilized onto self-assembled monolayers-modified gold electrode

A novel electrochemical sensor based on the immobilization of tyrosinase(tyr) onto gold nanoparticles(nano-Au) and thioctic acid amide(T-NH2) self-assembled monolayers(SAMs)-modified gold electrode has been developed for the determination of bisphenol A(BPA).It was found that the nano-Au could significantly enhance the electrochemical response of tyr/nano-Au/T-NH2/Au electrode to BPA,and the enhancement effect of nano-Au on the current response was also related to the enzyme.The results indicated that the biosensor could be used as a detector for BPA determination with a linear range from3.99 ×10-7mol/L to 2.34 ×10-4mol/L and a detection limit of 1.33×10-7mol/L.In addition,this biosensor showed good reproducibility.     

基于表面活性剂增敏有序介孔SiO2修饰碳糊电极测定L-色氨酸

利用水热法合成得到有序介孔二氧化硅( OMS),采用X射线衍射、N2吸附-脱附、透射电镜等技术对其进行了表征。制备OMS修饰碳糊电极( OMS/CPE),采用循环伏安和交流阻抗技术考察了修饰电极的电化学性能,发现与裸碳糊电极(CPE)相比,OMS/CPE具有更大的电活性面积和更快的电子传导速率。研究了L-色氨酸(L-Trp)在表面活性剂十二烷基磺酸钠(SDS)存在下,在OMS/CPE上的电化学行为和动力学性质,结果表明,OMS和SDS具有良好的协同作用,能明显增加L-Trp的响应信号; SDS存在下,L-Trp在修饰电极上的电化学氧化是2电子和2质子参加的不可逆过程,电极过程受吸附控制。优化了表面活性剂浓度、富集时间、富集电位、介质 pH 值等测定参数,在最优条件下, L-Trp 氧化峰电流与其浓度在8.0×10-8~4.0×10-6 mol/L范围内呈良好线性关系,检出限为7.0×10-8 mol/L(S/N=3)。本方法用于氨基酸口服液样品的加标回收检测,回收率为99.6％~102.6％。     

尿酸在石墨烯修饰玻碳电极上的电化学行为及测定

以抗坏血酸为还原剂,采用微波水热法化学还原氧化石墨烯合成了石墨烯纳米片,制备了石墨烯修饰的玻碳电极(RGO/GCE),并采用循环伏安法、计时电量法、交流阻抗法等电化学技术研究了尿酸在该修饰电极上的电化学行为及其影响因素。结果表明,在PBS缓冲溶液中,尿酸(UA)在石墨烯修饰电极上的电极反应是一个受扩散控制的不可逆氧化过程。电极反应的转移电子数n=2,有效面积A=0.182 cm2,扩散系数D=1.51×10-6 cm2.s-1。UA的氧化峰电流与其浓度在5.0×10-6～1.5×10-4 mol/L范围内呈良好线性,r=0.995 7。利用该RGO/GCE修饰电极可以快速准确地测定UA,检出限为2.7×10-7 mol/L,加标回收率为98%～100%。     

Electrochemical behavior of valsartan and its determination in capsules

Electrochemical behavior of valsartan has been carried out in Britton-Robinson (B-R) buffer solution at pH 7.0 at the mercury film electrode (MFE) by cyclic, linear sweep, differential-pulse and square-wave voltammetry. The property of valsartan adsorption at the MFE using accumulation potential of +0.10 V was observed. The effects of experimental parameters on electrochemical process at the MFE were discussed. Differential-pulse adsorptive stripping and square-wave adsorptive stripping voltammetry for the valsartan determination were proposed, linearity was found in the range of 6.0 x 10(-8) to 4.0 x 10(-6)mol/L. The detection limits were 2.93 x 10(-9) and 3.27 x 10(-9)mol/L, respectively. The proposed methods were also applied to the commercial valsartan with good recoveries.     

Determination of copper(II) by anodic stripping voltammetry at a 2,5-dimercapto-1,3,4-thiadiazol self-assembled monolayer-based gold electrode.

2,5-Dimercapto-1,3,4-thiadiazol (DMTD) can bind on the surface of a gold electrode through the strong gold-sulfur interaction. The fabrication and electrochemical characteristics of the DMTD self-assembled monolayer (SAM)-modified gold electrode were investigated. The DMTD SAM electrode exhibited a significantly increased sensitivity. Cu(II) was accumulated in phosphate buffer (pH 4.6) at a potential of -0.6 V (vs. Ag/AgCl) for 40 s and then determined by anodic stripping voltammetry (ASV) in copper-free phosphate buffer (pH 5.0). The effects of various parameters, such as the pH values of the preconcentration solution and measurement solution, the accumulation potential, and the accumulation time, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 8.0 x 10(-6) to 8.0 x 10(-5) mol l(-1) with a correlation coefficient of 0.9978. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-5) and 2.0 x 10(-5) mol l(-1) Cu(II), respectively. The detection limit (three times signal to noise) was 4.0 x 10(-7) mol l(-1). The proposed voltammetric method was utilized successfully to detect the concentration of Cu(II) ions in tap water samples.