新型Sn改性固体酸催化剂SO_4~(2-)/TiO_2催化1,6-己二醇二丙烯酸酯合成（英文）

丙烯酸酯单体包括通用丙烯酸酯和特种丙烯酸酯,不仅是高分子化合物的基本单体,也是化工有机反应的原料.特种丙烯酸酯在工业合成中虽然规模小,产量低,但已经应用到皮革、造纸、纺织、涂料、粘合剂和辐射固化技术等许多领域.辐射固化材料主要包括活性稀释剂、光引发剂、齐聚物和添加剂等.其中,齐聚物的主要成分就是丙烯酸酯单体的聚合物.然而,丙烯酸酯的合成工业难度不在合成路线,而是反应所使用的催化剂.浓硫酸和对甲苯磺酸等液体酸催化剂由于后续反应难分离、腐蚀设备、污染环境和催化剂不易回收等缺点,逐渐被固体酸催化剂所替代.而SO_4~(2-)/MOx固体酸催化剂虽然没有这些缺点,但是催化剂比表面积较小,热稳定性较差,酸性难以调节.为了合成1,6-己二醇二丙烯酸酯,本文首先对多种催化剂进行了筛选,获得了活性高且稳定好的SO_4~(2-)/TiO_2-SnO_2改性催化剂.采用N2吸附-脱附、X射线衍射(XRD)、扫描电镜(SEM)、红外光谱(IR)、吡啶红外、氨程序升温脱附和热重等技术考察了催化剂的结构特征、表面酸强度和热稳定性.通过N2吸附-脱附可知,Sn改性后催化剂的比表面积增加到126m~2/,较改性前有明显提高.XRD结果表明,Sn能较好地分散在催化剂载体表面,且随着Sn的加入,催化剂晶粒尺寸逐渐减小.SEM照片进一步证实了N2吸附-脱附和XRD结果.催化剂表面酸性通过吡啶红外和氨程序升温脱附测定.由IR图谱可知,固体酸催化剂SO_4~(2-)/TiO_2-SnO_2中SO_4~(2-)和金属原子的连接方式发生变化,更趋于螯合双齿配位结合.通过吡啶红外可以看出,当Sn添加量为6%时,改性催化剂的酸性位由未改性催化剂的59μmol/g增加到167μmol/g.氨程序升温脱附.结果表明,多次使用后催化剂的酸分布几乎不变,但酸量有所下降,这可能与催化剂表面硫源的损失有关.另外,通过热重对催化剂的热稳定性进行了分析,由于高温条件下孔结构容易坍塌导致硫源损失,因此第二个失重峰归属为SO_4~(2-)的脱除峰.Sn改性后的催化剂中SO_4~(2-)的脱除峰后移100 oC左右,且失重量为SO_4~(2-)/TiO_2的2倍多,说明SO_4~(2-)/TiO_2-SnO_2催化剂有更好的热稳定性和更多的酸性位.以1,6-己二醇和丙烯酸酯化反应中1,6-己二醇转化率和1,6-己二醇二丙烯酸酯收率为指标评价了催化剂的催化活性.主要研究了催化剂中Sn含量的影响,并对酯化反应条件进行了优化.结果表明,最适宜的Sn含量为6%,最优的反应条件为:酸/醇比3.5,催化剂添加量7%,酯化温度130oC,酯化时间3 h.最后考察了改性催化剂的稳定性.结果表明,催化剂使用10次后,1,6-己二醇转化率仍可达81%以上,固体酸催化剂SO_4~(2-)/TiO_2-SnO_2有良好的稳定性.     

焙烧温度对纳米级SO_4~(2-)/TiO_2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO42-/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO42-/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

新型介孔SO4^2-/TiO2固体酸的制备及其催化酯化性能

以无定形高比表面积水合钛酸(H2Ti2O5·xH2O)为载体,采用等体积浸渍法制备了新型晶须状介孔SO42-/TiO2固体酸催化剂,利用X射线衍射、N2吸附-脱附、扫描电镜、红外光谱、热重和氨程序升温脱附等技术考察了催化剂的结构特征和表面酸性及其对乙酸与正丁醇液相酯化反应的催化活性.结果表明,SO42-/TiO2同体酸催化剂不仅具有纳米级晶粒、晶须状形貌、高比表面积和介孔结构,还保持了完善的锐钛矿晶型、较强的酸性和较高的热稳定性;当焙烧温度高于500℃时,催化剂表面结合的SO42-逐渐流失,酸中心数逐渐减少.在m(催化剂)=0.2 g、n(正丁醇)/n(乙酸)=1.5和反应时间3 h条件下,500℃焙烧的催化剂活性最高,正丁醇转化率达94%,乙酸正丁酯选择性为100%,且催化性能和分离沉降性能均优于SO42-/P25催化剂.     

焙烧温度对纳米级SO2- 4/TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO2- 4/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO2-4/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

SO42-/TiO2-ZrO2复合氧化物固体酸催化剂的长叶烯芳构化催化性能

本工作用溶胶-凝胶法制备不同组成的SO42-/TiO2-ZrO2复合氧化物固体酸催化剂,用微型催化反应评价结合X-射线粉末衍射(XRD)、孔结构/BET表面积测试和NH3-程序升温脱附(NH3-TPD)等表征了SO42-/TiO2-ZrO2复合氧化物固体酸催化剂结构、表面酸性和长叶烯芳构化催化性能。复合氧化物固体酸SO42-/TiO2-ZrO2催化剂具有优良的长叶烯芳构化催化性能,并且其芳构化催化性能与催化剂组成和表面酸性密切相关。随催化剂中nZr/(nZr+nTi)增加,催化剂表面中等强度的酸中心量增加,芳构化产物选择性和收率明显增加,在nZr/(nZr+nTi)=0.5时达极大值。随nZr/(nZr+nTi)进一步增加,不仅催化剂表面酸中心量减少、原料转化率明显下降,而且催化剂酸强度增强,导致芳构化产物选择性和收率下降。催化长叶烯芳构化的二元复合氧化物固体酸SO42-/TiO2-ZrO2催化剂适宜的组成为nZr/(nZr+nTi)=0.5。     

焙烧温度对纳米级SO4^2-／TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO4^2-／TiO2固体超强酸，考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响．结果显示该催化剂在450℃焙烧3h，可以形成纳米级SO4^2-／TiO2固体超强酸的结构，用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98．4％。     

镧对固体超强酸SO42-/TiO2/Al交联膨润土的改性研究

采用镧对固体超强酸SO42-/TiO2/铝交联膨润土(S042-/TiO2/Al-PILC)进行改性,制备了La—SO42-/TiO2/Al-PILC稀土超强酸,并采用XRD、低温N2吸附法及吡啶吸附红外等方法对其进行了结构、表面性能及酸性的表征。实验结果表明,镧引人SO42-/TiO2/Al-PILC超强酸,对TiO2锐钛矿晶相的形成没有影响,但对锐钛矿晶相向金红石相的转变有抑制作用,镧的引人使催化剂的酸强度及酸中心的数量有所增加,镧能有效地减少催化剂表面SO42-的流失量,从而提高催化剂的活性稳定性。     

固体超强酸SO2-4/TiO2负载Tm改性的研究

负载稀土元素Tm以改性SO4^2-/TiO2,制备出固体超强酸催化剂Tm -SO4^2-/TiO2,并用于催化柠檬酸与正丁醇的酯化反应,考察了Tm的负载对催化剂性能的影响,并借助吡啶吸附的程序升温脱附（Py-TPD）法、差热分析（DTA）、热重分析（TGA）、红外光谱（IR）法研究其结构与性能的关系,实验结果表明,Tm的负载,使催化剂的催化活性有所提高,Tm的加量为催化剂量的3%时制得的Tm- SO4^2-/TiO2,其催化酯化反应的转化率为94.4%;Tm的负载能显著降低催化剂表面的积炭量,并且有效抑制So4^2-的流失,使Tm- SO4^2-/TiO2催化剂具有良好的稳定性,重复使用5次后反应的转化仍高达93.1%。     

SO_4~(2-)/TiO_2固体超强酸新制备方法及其对形成邻苯二甲酸二丁酯的催化活性

建立了用钛白粉制备固体超强酸SO42-/TiO2的新方法.考察了超强酸SO42-/TiO2的制备条件对催化邻苯二甲酸酐和正丁醇酯化反应的催化活性的影响.实验表明,以合成的超强酸为催化剂,在160℃反应4h,邻苯二甲酸二丁酯的产率大于99%.     

固体超强酸SO2-4/TiO2-SnO2的制备、表征及催化合成D, L-丙交酯

采用沉淀法在不同工艺条件下制备了稀土改性的新型固体超强酸SO2-4/TiO2-SnO2催化剂, 考察了其对D, L-乳酸合成D, L-丙交酯的催化活性, 并通过Hammett指示剂法测定了催化剂的酸强度, 用FT-IR和FT-Raman技术考察了焙烧温度、硫酸浸渍液浓度和浸渍时间以及La2O3的负载量对该固体超强酸结构和性能的影响. 研究结果表明: SnO2的存在促进了金红石相TiO2的形成, 在600 ℃焙烧3 h、 3.0 mol/L H2SO4溶液浸渍12 h、 n(Ti4+): n(Sn4+): n(La3+)=1:1:0.05条件下制备的SO2-4/TiO2-SnO2的酸强度最大, 达-13.75以上, 催化合成丙交酯的产率最高(78.4%). 并且考察了催化剂用量对D, L-丙交酯粗产率的影响和催化剂重复使用的性能.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.