Effect of Zn substitution for Co on the transport properties of Y BaCo4O7

Electrical resistivity and Seebeck coefficients of Y BaCo_4−xZn_xO₇ (x=0.0,0.5,1.0,2.0) were investigated in the temperature range 350-1000 K. It was found that the electrical resistivity and activation energy increase with increasing Zn concentration, while Seebeck coefficients do not increase but decrease when electrical resistivity increases. We explained the increase of electrical resistivity and the drop of Seebeck coefficients for Zn-substituted samples by the decrease of carrier mobility, rather than of carrier concentration. The effect of oxygen absorption and desorption on the electrical resistivity and Seebeck coefficients was also investigated. An abrupt change of transport properties happens at about 650 K for x=0.0 and 0.5 samples measured in oxygen. For x=1.0 and 2.0 samples, however, such change disappears and the transport behavior in oxygen is almost same as that in nitrogen due to the significant suppression of oxygen diffusion caused by the higher Zn concentration in these samples.     

High-temperature electronic transport properties of La1−xCaxMnO3+δ (0.0?x?1.0)

La_1−xCa_xMnO_3+δ (0.0?x?1.0) samples were prepared and their resistivity and Seebeck coefficients were measured in the high-temperature range. Ca doping changes the ratio of Mn³⁺/Mn⁴⁺ and influences the electronic transport behavior markedly. With the increase of Ca concentration, the samples change from a p-type semiconductor to an n-type one and Seebeck coefficient becomes increasingly negative. Low doping (x=0.2) and high doping (x=0.8) induces the drop of the resistivity compared with undoped LaMnO_3+δ and CaMnO_3+δ samples due to the rise of carrier concentration. However, the resistivity of moderate-doped samples (x=0.4, 0.6) is larger than low- and high-doped samples because dopant scattering decreases carrier mobility.     

Thermoelectric properties of Gd,Y co-doped Ca3Co4O9+δ

The Ca_3−x−yGd_xY_yCo₄O_9+δ precursor powders were synthesized by the polyacrylamide gel method. The powders were sintered by the spark plasma sintering (SPS). The DTA analysis showed that the synthesis temperature of Ca₃Co₄O_9+δ was about 933 K, which is lower than that of the conventional citric acid method. The resistivities, the Seebeck coefficients and the thermal conductivities of the samples were measured from room temperature to 973 K. The Seebeck coefficients and the resistivities of the doped samples were remarkably enhanced due to the decrease of the carrier concentration, whereas the thermal conductivities of them were decreased due to the impurity scattering effect. The maximal ZT value of 0.26 was obtained at 973 K for Ca_2.7 Gd_0.15 Y_0.15Co₄O_9+δ.     

Thermoelectric properties of the Bi2−xYxRu2O7 (x=0-2) pyrochlores

Electrical conductivity and Seebeck coefficient for the Bi_2−xY_xRu₂O₇ pyrochlores with x=0.0,0.5,1.0,1.5,2.0 were measured in the temperature range of 473-1073 K in air. With increasing Bi content, the temperature dependence of the electrical conductivity changed from semiconducting to metallic. The signs of the Seebeck coefficient were positive in the measured temperature range for all the samples, indicating that the major carriers were holes. The temperature dependence of the Seebeck coefficient for the Y₂Ru₂O₇ indicated the thermal activation-type behavior of the holes, while that for the Bi_2−xY_xRu₂O₇ with x=0.0-1.5 indicated the itinerant behavior of the holes. The change in the conduction behavior from semiconductor to metal with increasing Bi content is consistent with the increase in the overlap between the Ru4d t_2g and O2p orbitals, but the mixing of Bi6s, 6p states at E_F may not be ruled out. The thermoelectric power factors for the Bi_2−xY_xRu₂O₇ with x=1.5 and 2.0 were lower than 10⁻⁵ W m⁻¹ K⁻² and those with x=0.0,0.5,1.0 were around 1-3×10⁻⁵ W m⁻¹ K⁻².     

Thermoelectric properties of Ca3−xYxCo4O9+δ ceramics

The Ca_3?xY_xCo₄O_9+δ (x=0, 0.15, 0.3) ceramics were prepared by combining the polyacrylamide gel method and the spark plasma sinter (SPS) technology in order to improve the thermoelectric properties of Ca₃Co₄O_9+δ ceramics. The Seebeck coefficients and the resistivities of the Y-doped samples were obviously enhanced due to the decrease of carrier concentration, and their thermal conductivities were decreased due to the impurity scattering effect. The thermoelectric properties were improved at high temperature by Y-doping according to the power factor analysis and the thermoelectric figure of merit (ZT) data. The optimized figure of merit ZT=0.22 at 973 K was obtained for Ca_2.7Y_0.3Co₄O_9+δ.     

Control of luminescence and conductivity of delafossite-type CuYO2 by substitution of rare earth cation (Eu, Tb) and/or Ca cation for Y cation

Delafossite-type oxides of CuTb_yY_1−yO₂, CuEu_yY_1−yO₂, CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ have been prepared by solid state reactions. The lattice-parameter dependence on the composition implies substitution of the Tb³⁺, Eu³⁺ and Ca²⁺ cations for the Y³⁺ site. Noticeable sharp emission lines due to the f-f transitions (⁵D₄→⁷F_J, J=3-6) of Tb³⁺ or due to the f-f transitions (⁵D₀→⁷F_J, J=0-4) of Eu³⁺ are observed at room temperature. Electrical conductivities of CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ are larger than those of CuTb_yY_1−yO₂ and CuEu_yY_1−yO₂, indicating the increase of the hole concentration caused by the substitution of Ca²⁺ for the Y³⁺ site. These results indicate the controllability of the luminescence and conductivity in CuCa_xTb_yY_1−x−yO₂ and CuCa_xEu_yY_1−x−yO₂ delafossite-type oxides by simultaneous substitution of the rare earth Tb³⁺ or Eu³⁺ cation and the Ca²⁺ cation for the Y³⁺ site.     

Magnetoresistance effect in A 2(FeMo)Ox double perovskites (A = Sr, Ca; 5.90≤x≤6.05)

The dependences of magnetic, electric, and magnetotransport properties on oxygen non stoichiometry were investigated in compounds of Ca₂(FeMo)O_x and Sr₂(FeMo)O_x (5.90≤x≤6.05). The regular trends in behavior of the magnetization, resistance, and magnetoresistance of samples of these series are determined. It is established that the magnetoresistance is composed of two parts that appear as a result of magnetic ordering in grain-boundary layers and of the intergrain transport of spin-polarized charge carriers. The electronic transport in the samples is assumed to be governed by percolation processes between grains which have a metallic type of conductivity and are separated by insulating spacers.     

Impact of Pr on structural,superconducting and magnetic properties of Y1−xPrxBaSrCu3O7

We study the structural, superconducting and magnetic properties of the Y_1−xPr_xBaSrCu₃O₇ system with x=0.0, 0.20, 0.25, 0.30, 0.40, 0.50, 0.60, 0.75 and 1.0, from X-ray diffraction, AC and DC magnetic susceptibility measurements. X-ray diffraction results reveal that while Pr substitutes isostructurally until x=0.50 in Y_1−xPr_xBaSrCu₃O₇, for x=0.75 and 1.0 few small intensity un-reacted lines are observed in the spectrum. The orthorhombic distortion decreases with an increase in x. Both x=0.75 and 1.0 samples are tetragonal. The c lattice parameter of the substituted samples increases with x, indicating probable substitution of comparatively bigger ionic radii Pr^3+/4+ ion at Y³⁺ in Y_1−xPr_xBaSrCu₃O₇ system. The AC susceptibility results showed that the transition temperature T_c of the Y_1−xPr_xBaSrCu₃O₇ system decreases monotonically with an increase in x. Both x=0.75 and 1.0 samples do not show a superconducting transition down to 4.2 K. The critical concentration of Pr to completely suppress superconductivity in Y_1−xPr_xBaSrCu₃O₇ is higher (0.75) than that reported (0.55) for Y_1−xPr_xBa₂Cu₃O₇. DC magnetic susceptibility measurements done on PrBaSrCu₃O₇ and PrBa₂Cu₃O₇ samples at 0.5 T revealed that while the Pr ordering temperature seems to be 12 K for the former, the same is 17 K for the latter. These results indicate that the ordering temperature of Pr moments in RE_1−xPr_x : 123-type systems, which decides the Pr^4f hybridisation with the Cu–O conduction band has a direct connection to the suppression of superconductivity. The lower T_N of Pr explains the less destructive effect of the same on the superconductivity of the parent undoped system.     

Effects of protons and acceptor substitution on the electrical conductivity of La6WO12

Transport properties and non-stoichiometry of La_1−xCa_xW_1/6O₂ and La_1−yW_1/6O₂ (x=0, 0.005, 0.05; y=0.05, 0.1) have been characterized by means of impedance spectroscopy, the EMF-technique, H⁺/D⁺ isotope exchange, and thermogravimetry in the temperature range 300-1200 °C as a function of oxygen partial pressure and water vapor partial pressure. The materials exhibit mixed ionic and electronic conductivities; n- and p-type electronic conduction predominate at high temperatures under reducing and oxidizing conditions, respectively. Protons are the major ionic charge carrier under wet conditions and predominates the conductivity below ∼750 °C. The maximum in proton conductivity is observed for LaW_1/6O₂ with values reaching 3×10⁻³ S/cm at approximately 800 °C. The high proton conductivity for the undoped material is explained by assuming interaction between water vapor and intrinsic (anti-Frenkel) oxygen vacancies.     

Impedance-based interpretations in 2-dimensional electron gas conduction formed in the LaAlO3/SrxCa1−xTiO3/SrTiO3 system

Frequency-dependent impedance spectroscopy was applied to the 2-dimensioanl conduction transport in the LaAlO₃/Sr_xCa_1−xTiO₃/SrTiO₃ system. The 2-dimensional conduction modifies the electrical/dielectric responses of the LaAlO₃/Sr_xCa_1−xTiO₃/SrTiO₃ depending on the magnitude of the interfacial 2-dimensional resistance. The high conduction of the 2-dimensional electron gas (2DEG) layer can be described using a metallic resistor in series with two parallel RC circuits. However, the high resistance of the 2-dimensional layer drives the composite system from a finite low resistor in parallel with the surrounding dielectrics composed of LaAlO₃ and SrTiO₃ materials to a dielectric capacitor. This change in the resistance of the 2-dimensional layers modifies the overall impedance enabled by the presence of the interfacial layer due to Sr_xCa_1−xTiO₃, which alters the charge transport of the 2-dimensional layer from metallic to semiconducting conduction. A noticeable change is observed in the capacitance Bode plots, indicating highly amplified dielectric constants compared with the pristine SrTiO₃ substrates and Sr_xCa_1−xTiO₃ with a greater Ca content.     

Superconductivity, Seebeck coefficient, and band structure transformation in Y1−x CaxBa2Cu3−x CoxOy (x=0–0.3)

The temperature dependences of the resistivity and of the Seebeck coefficient S is studied in three series of Y_1−x Ca_xBa₂Cu_3−x Co_xO_y samples (x=0–0.3) differing in oxygen content. It was found that the critical temperature decreases for y≈7.0, and S(T=300 K) increases with doping, whereas oxygen deficiency results in a nonmonotonic variation of these quantities with increasing x. The band structure parameters have been determined from an analysis of the S(T) relations using a phenomenological theory of electron transport. It was found that an increase in x results in a gradual increase in band asymmetry, which is caused by calcium-induced creation of additional states in the band responsible for conduction in the normal phase. An analysis has shown that high impurity concentrations in oxygen-deficient Y_1−x Ca_xBa₂Cu_3−x Co_xO_y samples bring about an additional ordering of the structure, which may be caused by formation of a cobalt superlattice. It has also been shown that, in the case of Ca and Co codoping, the dependence of critical temperature on effective conduction-band width coincides with the universal correlation relation observed in the YBa₂Cu₃O_y system with single substitutions in various lattice sites. Fiz. Tverd. Tela (St. Petersburg) 41, 1363–1371 (August 1999)     

Defect formation and transport in mixed-conducting La0.90Sr0.10Al0.85−xFexMg0.15O3−δ

The redox behavior of perovskite-type La_0.90Sr_0.10Al_0.85−xFe_xMg_0.15O_3−δ (x=0.20-0.40) mixed conductors was analyzed by the Mössbauer spectroscopy and measurements of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10⁻²⁰ to 0.5 atm at 1023-1223 K. The results combined with oxygen-ion transference numbers determined by the faradaic efficiency technique in air, were used to calculate defect concentrations, mobilities, and partial ionic and p- and n-type electronic conductivities as a function of oxygen pressure. The redox and transport processes can be adequately described in terms of oxygen intercalation and iron disproportionation reactions, with the thermodynamic functions independent of defect concentrations. No essential delocalization of the electronic charge carriers was found. The oxygen non-stoichiometry values estimated from the conductivity vs. p(O₂) dependencies, coincide with those evaluated from the Mössbauer spectra.     

Superconductivity in CoSr2(Y1−xCax)Cu2O7+δ

The roles of aliovalent Ca^II-for-Y^III substitution and high-pressure-oxygen annealing in the process of ‘superconducterizing’ the Co-based layered copper oxide, CoSr₂(Y_1−xCa_x)Cu₂O_7+δ (Co-1212), were investigated. The as-air-synthesized samples up to x=0.4 were found essentially oxygen stoichiometric (−0.03≤δ≤0.00). These samples, however, were not superconducting, suggesting that the holes created by the divalent-for-trivalent cation substitution are trapped on Co in the charge reservoir. Ultra-high-pressure heat treatment carried out at 5 GPa and 500 °C for 30 min in the presence of Ag₂O₂ as an excess oxygen source induced bulk superconductivity in these samples. The highest T_c was obtained for the high-oxygen-pressure treated x=0.3 sample at ∼40 K.     

Phase formation and dielectric phase transition in Ba1−xCaxTi0.6Zr0.4O3 solid solutions

Perovskite types Ba_1−xCa_xTi_0.6Zr_0.4O₃ (with x=0.0-0.5) ceramics have been prepared through solid state reaction route. The room temperature XRD study suggests the compositions with x=0.0 and x=0.1 have single phase cubic symmetry. With further increase in Ca content, solid solution breaks and an orthorhombic CaTiO₃ like phase is developed. The dielectric study on single phase compositions (x=0.0 and 0.1) reveals that the materials are of relaxor type and undergo a diffuse type ferroelectric phase transition. In the Ca containing composition higher transition temperature is observed than the pure BaTi_0.6Zr_0.4O₃ materials. In the paraelectric region (above T_c) lower diffusivity is observed in the Ca containing composition. The strength of relaxation is calculated and found to be more in Ca containing material than that of pure BaTi_0.6Zr_0.4O₃ composition.     

Superlattice structures in solid solution of high-Tc YBa2Cu3O7−δ and (Pb,Cu)Sr2(Ca,Y)Cu2O7−δ superconductors

A complete solid solution range exists between the systems YBa₂Cu₃O_7−δ and (Pb,Cu)Sr₂(Ca,Y)Cu₂O_7−δ has been found with general stoichiometry (Pb_0.75xCu_1−0.75x)(Sr_2xBa_2−2x)(Ca_0.5xY_1−0.5x)Cu₂O_7−δ. Energy dispersive spectrometry and X-ray diffraction identified that a true solid solution exists. Superlattice structures observed by electron diffraction across the solid solution range have a modulation range have a modulation periods along a* which can be varied by altering both the compositional parameter x and the overall oxygen content. The existence of these superlattices infers that the solid solution is non-random and therefore thermodynamically non-ideal. The superconducting transition temperatures, T_c, across the solid solution range are also strongly dependent on the composition, x, but no direct relationship with the modulation period has been established. From these studies it may be concluded that the solid solution between known superconductors is possible, although involving some partial ordering of the lattice, but ordering of cations in the rock-salt to charge reservoir layer is not a significant factor in determining the superconducting properities, which depend more closely on the overall composition and hence on the ability of the charge reservoir layer to transfer charge to the superconducting layers.     

Band spectrum modification and dynamics of superconducting properties in the Y1?xCaxBa2Cu3?xZnxOy system

Temperature dependences of the electrical resistivity and Seebeck coefficient have been studied on a series of samples of the Y_1−x Ca_xBa₂Cu_3−x Zn_xO_y system (x = 0–0.25). The effect exerted by a combination of the impurities under study on the properties of the normal phase was established. The experimental data obtained were analyzed quantitatively in terms of a phenomenological model of electron transport. The parameters of the band responsible for conduction in the normal phase and of the carrier system were calculated for all the samples studied. A mechanism of zinc doping-induced band structure modification in the yttrium system is proposed that accounts for the transformation of the temperature dependence of the Seebeck coefficient and the dynamics of superconducting properties in this compound. __________ Translated from Fizika Tverdogo Tela, Vol. 47, No. 3, 2005, pp. 422–426. Original Russian Text Copyright ? 2005 by Elizarova, Martynova, Potapov, Gasumyants, Mezentseva.     

Synthesis, structural and physical properties of new Terbium containing Tb-Hg-Sr-Ca-Cu-O superconducting system

Samples with various nominal compositions in the Tb-Hg-Sr-Ca-Cu-O system were prepared and studied by EDX, powder X-ray diffraction including the Rietveld refinement, electrical resistivity, magnetic susceptibility and thermoelectric power measurements. EDX and powder X-ray diffraction studies showed that Tb is required for the stabilization of the 1212, (Hg_1−yTb_y)Sr₂TbCu₂O_6+δ; y≈0.5 phase. Electrical resistivity and magnetic susceptibility measurements indicated that substitution of Tb by Ca is necessary to induce superconductivity in the 1212, (Hg_0.5Tb_0.5)Sr₂(Tb_1−xCa_x)Cu₂O_6+δ samples. The Rietveld refinements of the X-ray data of two samples with x=0.0 and 0.5 were carried out on the basis of tetragonal symmetry (space group P4/mmm) and the results indicated that the phase with x=0.5 has less puckered Cu-O planes than the Ca-free (Hg_0.5Tb_0.5)Sr₂TbCu₂O_6+δ phase. Syperconductivity is observed only for samples with x>0.2 and T_c increases with increasing Ca content, x. The results of thermoelectric power measurements suggest that the samples with x<0.8 are located in the underdoped region and the x=0.8 sample is optimally doped and exhibits the highest T_c of 88 K.     

Crystal structure, electronic and transport properties of AgSbSe2 and AgSbTe2

Undoped and p- and n-doped AgSbX₂ (X=Se and Te) materials were synthesized by direct fusion technique. The structural properties were investigated by X-ray diffraction and SEM microscopy. The electrical conductivity, thermal conductivity and Seebeck coefficient have been measured as a function of temperature in the range from 300 to 600 K.To enlighten electron transport behaviours observed in AgSbSe₂ and AgSbTe₂ compounds, electronic structure calculations have been performed by the Korringa-Kohn-Rostoker method as well as KKR with coherent potential approximation (KKR-CPA) for ordered (hypothetical AgX and SbX as well as AgSbX₂ approximates) and disordered systems (Ag_1−xSb_xX), respectively. The calculated density of states in the considered structural cases shows apparent tendencies to opening the energy gap near the Fermi level for the stoichiometric AgSbX₂ compositions, but a small overlap between valence and conduction bands is still present. Such electronic structure behaviour well agrees with the semimetallic properties of the analyzed samples.     

Microstructural and electrical characterisation of melt grown high temperature protonic conductors

High temperature protonic conductors of SrCe_1−xY_xO_3−δ and Sr₃Ca_1+xNb_2−xO_9−δ were fabricated by directional solidification to produce model microstructures. Elongated cells exhibited 〈100〉 direction parallel to the growth axis; low degree of disorientation was observed between the cells. In the simple perovskite SrCe_1−xY_xO_3−δ aluminum contamination caused the formation of intergranular second phase. Nuclear microprobe revealed that the second phase was enriched with hydrogen. Impedance spectroscopy revealed that the protons at grain boundaries have a lower mobility than within the cells. The cation distribution was not uniform in the complex perovskite. Inverse gradients in Ca²⁺ and Nb⁵⁺ were observed from the core to the shell of the cells. The Nb⁵⁺ substitution decreased from x = 0.12 at the core to 0.07 at the shell. Higher Nb⁵⁺/Ca²⁺ ratio at the shell decreased the protonic conductivity. Nanodomain were observed in both perovskite compositions; they differentiate by a 90° rotation of the direction of oxygen cage tilting. In the complex perovskite, stoichiometric domains with an ordered distribution of Nb⁵⁺ and Ca²⁺ were surrounded by nonstoichiometric domains with a random distribution of these cations. Further work and analyses are required to understand the mechanism of proton transfer within domains and across domain interfaces.     

Y1-xCaxBa2Cu3-xMxO7-δ (M=Fe,Ni)体系的超导电性

本文报道,通过对Y_1-xCa_xBa₂Cu_3-xMxO_7-δ(M=Fe,Ni)体系样品的晶体结构、氧含量、正常态电阻率与温度的关系,以及超导转变温度等测量,并与YBa₂Cu_3-xMxO_7-δ(M=Fe,Ni)体系进行比较,发现Y_1-xCa_xBa₂Cu_3-xFe_xO_7-δ体系的T_c显著地高于相应x值的YBa₂Cu_3-xFe_xO_7-δ体系,而Y_1-xCa_xBa₂Cu_3-xNi_xO_7-δ体系则相反,T_c低于仅Ni替代的体系,表明Ca和Fe同时替代时两者引起的载流子浓度(n_H)变化相互补偿,抑制了仅Fe替代时引起的n_H和T_c急剧下降;而作Ca和Ni同时替代时主要的不是两者引起载流子浓度变化的相互补偿,Ca和Ni替代效应之间的关联较弱。作者认为,对Y_1-xCa_xBa₂Cu_3-xFe_xO_7-δ体系属于CuO₂平面外的元素替代,这时载流子浓度是决定Tc的主要因素;而对Y_1-xCa_xBa₂Cu_3-xNi_xO_7-δ体系,由于Ni²⁺离子主要占据Cu(Ⅱ)位,它导致磁拆对效应,Ni²⁺离子的拆对效应是引起T_c下降的直接原因。 关键词：