Synthesis of Ag/NiO composite nanosheets and empty microspheres and their highly effective electrocatalytic properties

Ag/NiO composite nanosheets and empty microspheres were fabricated by calcining the precursors synthesized via hydrothermal and solvothermal procedures involved four methods. The as-prepared samples were characterized by thermogravimetric and differential thermal analysis, X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy and field emission scanning electron microscopy, respectively. The electrocatalytic properties of Ag/NiO composites modified on a glassy carbon electrode for p-nitrophenol reduction were investigated. The results showed that Ag/NiO composites exhibited highly enhanced electrocatalytic activity than a bare glassy carbon electrode, for not only the peak current increased clearly but also the corresponding peak potential decreased markedly. As a comparison, two NiO samples were used and the results showed that the peak current has an increase but the peak potentials have a slight decrease by comparing to a bare glassy carbon electrode. The Ag/NiO composites have the potential application in the electrocatalysis for the reduction of nitrophenol materials.     

A highly sensitive nonenzymatic glucose sensor based on nickel oxide–carbon nanotube hybrid nanobelts

In this study, we demonstrated a highly sensitive electrochemical sensor for the determination of glucose in alkaline aqueous solution by using nickel oxide single-walled carbon nanotube hybrid nanobelts (NiO–SWCNTs) modified glassy carbon electrode (GCE). The hybrid nanobelts were prepared by the deposition of SWCNTs onto the Ni(SO₄)_0.3(OH)_1.4 nanobelt surface, followed by heat treatment at different temperatures ranging from 400 °C to 600 °C. The NiO–SWCNTs hybrid nanobelts modified electrode prepared at 500 °C displays enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the NiO and the deposited SWCNTs. The as-fabricated nonenzymatic glucose sensor exhibits excellent glucose sensitivity (2,980 μA cm^?2 mM^?1), lower detection limit (0.056 μM, signal/noise [S/N] ratio?=?3), and wider linear range (0.5–1,300 μM). Moreover, the sensor has been successfully used for the assay of glucose in serum samples with good recovery, ranging from 96.4 % to 102.4 %.     

Synthesis of Hexagonal Co3O4 and Ag/Co3O4 Composite Nanosheets and their Electrocatalytic Performances

Sheet-like precursors of Co₃O₄ and Ag/Co₃O₄ composites with different Ag contents were synthesized with assistance of triethylamine via a hydrothermal process. The final samples were fabricated by calcing each precursor at 400 °C. The as-prepared samples were identified and characterized by thermogravimetric analysis and differential thermal analysis, X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and field emission scanning electron microscopy, respectively. The Co₃O₄ and Ag/Co₃O₄ composite samples were used as electrocatalysts modified on a glassy carbon electrode for p-nitrophenol reduction in a basic solution. The electrocatalytic results indicated that all the samples showed enhanced electrocatalytic performance for p-nitrophenol by comparing a bare glass carbon electrode, and p-nitrophenol could be reduced by Co₃O₄ at a high peak current but a rather higher peak potential but be reduced effectively by Ag/Co₃O₄ composites at lower potential. Ag/Co₃O₄ composites with 4 % Ag displayed the highest electrocatalytic activity.     

Selective Detection of Dopamine in the Presence of Uric Acid Using NiO Nanoparticles Decorated on Graphene Nanosheets Modified Screen‐printed Electrodes

A convenient, low cost, and sensitive electrochemical method, based on a disposable graphene nanosheets (GR) and NiO nanoparticles modified carbon screen printed electrode (NiO/GR/SPE), is described for the simultaneous determination of dopamine (DA) and uric acid (UA). The modified electrode exhibited good electrocatalytic properties toward the oxidation of DA and UA. A peak potential difference of 150 mV between DA and UA was large enough to determine DA and UA individually and simultaneously. The anodic peak currents of DA were found to be linear in the concentration range of 1.0–500.0 μM with the detection limit of 3.14×10^?7 M.     

Synthesis of Fe3O4, Fe2O3, Ag/Fe3O4 and Ag/Fe2O3 nanoparticles and their electrocatalytic properties

Two important iron oxides:Fe3O4 and Fe2O3,as well as Fe3O4 and Fe2O3 nanoparticles mingling with Ag were successfully synthesized via a hydrothermal procedure.The samples were confirmed and characterized by X-ray diffraction(XRD),and X-ray photoelectron spectroscopy(XPS).The morphology of the samples was observed by transmission electron microscopy(TEM).The results indicated Fe3O4,Fe2O3,Ag/Fe3O4 and Ag/Fe2O3 samples all were nanoparticles with smaller sizes.The samples were modified on a glassy carbon electrode and their elctrocatalytic properties for p-nitrophenol in a basic solution were investigated.The results revealed all the samples showed enhanced catalytic performances by comparison with a bare glassy carbon electrode.Furthermore,p-nitrophenol could be reduced at a lower peak potential or a higher peak current on a glassy carbon electrode modified with Ag/Fe3O4 or Ag/Fe2O3 composite nanoparticles.     

Facile synthesis of Co3O4 and Ag/Co3O4 nanosheets and their electrocatalytic properties

The precursors of Co₃O₄ and Ag/Co₃O₄ composites with different Ag contents were synthesized with assistance of (NH₄)₂CO₃ via a facile hydrothermal process. The final samples were fabricated by calcining each precursor at 400 °C according to TG experiment. The as-prepared samples were identified and characterized by thermogravimetric analysis, X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and field emission scanning electron microscopy, respectively. The results showed that the morphology of Co₃O₄ and Ag/Co₃O₄ composites were sheet-like. Ag nanoparticles were dispersed well in the nanosheets. The samples were used as electrocatalysts modified directly on a glassy carbon electrode for p-nitrophenol reduction in a basic solution. The results showed that p-nitrophenol could be reduced at a large peak current but a higher peak potential with Co₃O₄, at lower potentials with Ag/Co₃O₄ composites. Ag/Co₃O₄ composite with 3 % Ag showed more efficiently electrocatalytic activity than other composites. The present method suggested the potential application of Ag/Co₃O₄ composites in electrocatalysis.     

银纳米颗粒的合成及用于抗癌药氟他胺的电化学检测（英文）

Ag nanoparticles were synthesized on the surface of a glassy carbon electrode modified with p‐tert‐butylcalix[4]arene and p‐tert‐butylcalix[6]arene by the deposition of Ag+ at an open circuit potential followed by the electrochemical reduction of the Ag+.The presence of the calixarene layer on the electrode surface controlled the particle size and prevented agglomeration.Cyclic voltam‐metry showed that the Ag nanoparticles on the modified glassy carbon electrode had good catalytic ability for the reduction of flutamide.The effects of calixarene concentration,potential applied for the reduction of Ag+,number of calixarene layers,and p H value on the electrocatalytic activity of the Ag nanoparticles were investigated.The modified electrode had a linear range in differential pulse voltammetry of 10-1000 μmol/L with a detection limit of 9.33 μmol/L for flutamide at an S/N = 3.The method was applied to the detection of flutamide in practical samples.     

Ag Doped Titanium Dioxide Nanocomposite‐modified Glassy Carbon Electrode as Electrochemical Interface for Catechol Sensing

The electrochemical sensing of catechol (CC) on a glassy carbon electrode modified with the ionothermal assisted synthesis of Ag doped TiO₂ a nanoparticle has been successfully demonstrated for the first time.Ag doped TiO₂ nanoparticles composite modified glassy carbon electrode exhibits higher electrocatalytic activity towards oxidation of catechol than glassy carbon electrode itself. The modified electrode also exhibits high selectivity towards this analyte in the presence of some of the metal ions and some of the biological compounds. Linear ranges and the limit of detections with the above electrode are 1–15 µM and 0.0249 µM respectively. The optimized protocol has been utilized for monitoring the catechol in some of the natural samples like apple juice and green tea and in industrial effluents.     

Electrocatalytic dechlorination of chloroacetic acids by silver nanoparticles modified glassy carbon electrode

A simple potentiostatic method was employed to prepare silver nanoparticles deposited on glassy carbon electrode. The silver nanoparticles exhibit extraordinary electrocatalytic activities toward the reduction process of chloroacetic acids. The electrochemical behavior of trichloroacetic acid, dichloroacetic acid, and monochloroacetic acid has been investigated by cyclic voltammetry at the silver nanoparticles-modified glassy carbon electrode in 0.1 M LiClO₄ solution; each compound exhibits a series of reduction peaks which represent sequential dechlorination steps up to acetic acid. The electrocatalytic dechlorination mechanism for chloroacetic acids was also discussed in this work.     

Synthesis and electrocatalytic properties of microsized Ag2WO4 and nanoscaled MWO4 (M=Co, Mn)

Microstructured Ag₂WO₄ with shuttle-like shape was synthesized via a precipitation process with assistance of Arabic gum. MWO₄ (M=Co and Mn) nanocrystals were prepared facilely via a hydrothermal procedure. The as-prepared samples were identified and characterized by X-ray diffraction, transmission electron microscopy, and scanning electron microscopy, respectively. The resultant samples were used directly as electrocatalysts modified on a glassy carbon electrode for p-nitrophenol, K₂CrO₄ and H₂O₂ reduction in a basic solution. The results showed that all peak currents increased markedly but the corresponding peak potential decreased by using CoWO₄, MnWO₄ and Ag₂WO₄ in turn by comparing to a bare glassy carbon electrode, and Ag₂WO₄, CoWO₄ and MnWO₄ exhibited enhanced electrocatalytic activity for p-nitrophenol reduction. Ag₂WO₄ also showed effective electrocatalytic activity for K₂CrO₄ and H₂O₂ reduction, but both CoWO₄ and MnWO₄ almost displayed very weak electrocatalytic properties for K₂CrO₄ and H₂O₂ reduction in basic solution.     

Electrocatalytic Reduction of Dioxygen on the Surface of Glassy Carbon Electrodes Modified with Cobalt Porphyrin Complexes

The preparation and electrocatalytic behavior of glassy carbon electrodes modified with three different cobalt porphyrin complexes were investigated. The electrocatalytic ability of the modified electrodes for the reduction of dioxygen to hydrogen peroxide and water in air‐saturated aqueous solutions was examined by cyclic voltammetry and chronoamperometry techniques. The porphyrin‐adsorbed glassy carbon electrodes possess excellent electrocatalytic abilities for dioxygen reduction with overpotential about 0.5 V lower than that at a plain glassy carbon electrode. The experimental parameters were optimized and the mechanism of the catalytic process was discussed. The possible effects of the electron‐donating properties of groups in the meso‐position of the porphyrin ring were investigated.     

Simultaneous determination of hydroquinone and catechol based on glassy carbon electrode modified with gold-graphene nanocomposite

We have synthesized a virtually monodisperse gold-graphene (Au-G) nanocomposite by a single-step chemical reduction method in aqueous dimethylformamide solution. The nanoparticles are homogenously distributed over graphene nanosheets. A glassy carbon electrode was modified with this nanocomposite and displayed high electrocatalytic activity and extraordinary electronic transport properties due to its large surface area. It enabled the simultaneous determination of hydroquinone (HQ) and catechol (CC) in acetate buffer solution of pH?4.5. Two pairs of well-defined, quasi-reversible redox peaks are obtained, one for HQ and its oxidized form, with a 43 mV separation of peak potentials (ΔE_p), the other for CC and its oxidized form, with a ΔE_p of 39 mV. Due to the large separation of oxidation peak potentials (102 mV), the concentrations of HQ and CC can be easily determined simultaneously. The oxidation peak currents for both HQ and CC increase linearly with the respective concentrations in the 1.0 μM to 0.1 mM concentration range, with the detection limits of 0.2 and 0.15 μM (S/N?=?3), respectively. The modified electrode was successfully applied to the simultaneous determination of HQ and CC in spiked tap water, demonstrating that the Au-G nanocomposite may act as a high-performance sensing material in the selective detection of some environmental pollutants.

Electrochemical reduction of dioxygen on Alizarin modified glassy carbon electrode in acidic medium

The catalytic behaviour of glassy carbon electrode modified by 1,2-dihydroxy antraquinone (Alizarin) was investigated. The electrocatalytic ability of modified electrode for the reduction of dioxygen was examined by cyclic voltammetry and rotating disk electrode (RDE) voltammetry techniques. The Alizarin modified glassy carbon electrode possesses excellent electrocatalytic abilities for dioxygen reduction over potential 400 mV lower than at the bare glassy carbon electrode. Hydrodynamic studies were performed to determine the heterogeneous rate constant for the reduction of O₂ at the surface of modified electrode. It was determined by Koutecky-Levich plot. The apparent diffusion coefficient of O₂ in O₂ saturated acidic solutions was estimated by using Levich equation. Studies show the involvement of four electrons in dioxygen reduction at the surface of this modified electrode.     

Preparation of hybrid thin film modified carbon nanotubes on glassy carbon electrode and its electrocatalysis for oxygen reduction

A hybrid thin film containing Pt nanoparticles and [tetrakis(N-methylpyridyl)porphyrinato]cobalt (CoTMPyP) modified multi-walled carbon nanotubes (MWNTs) on a glassy carbon (GC) electrode surface was fabricated. This hybrid film electrode exhibited remarkable electrocatalytic activity for oxygen reduction and high stability with promising applications in fuel cells.     

Synthesis and Electrocatalytic Properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanocrystallites with Various Morphologies

Co₃O₄ crystallites with particle, plate-, tube-, rod- and sheet-like morphologies were successfully prepared by the calcination of the corresponding precursors synthesized via a precipitation or hydrothermal procedure. The morphologies of the precursors and Co₃O₄ nano-tubes were detected by field emission scanning electron microscopy (FE-SEM). The as-obtained Co₃O₄ samples were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and special surface area measurement (BET). The electrocatalytic activity of p-nitrophenol reduction with the Co₃O₄ products decorated on a glassy carbon electrode (GCE) was tested, respectively, using cyclic voltammetry (CV) in a basic solution. The results indicated that p-nitrophenol was reduced with higher current density but almost at a constant potential on the Co₃O₄/GCE in contrast with that on a bare GCE at the same conditions. The highly catalytic activity of the as-prepared Co₃O₄ in a basic solution suggested their wide applications in environmental treatment or organic synthesis.     

The effect of electrocatalytic nanoparticle injection on the electrochemical response at a rotating disc electrode

A new approach to study electrocatalytic oxidation of glucose is proposed. As opposed to numerous studies on electrodes modified with gold nanoparticles this reaction was studied in their suspension of gold nanoparticles under hydrodynamic conditions on a noncatalytic glassy carbon rotating disc electrode. It has been shown that addition of nanogram amount of positively charged Au nanoparticles results in a clear current response, whereas no clear response is seen for negatively charged ones. This effect results from the electrocatalytic oxidation of glucose on Au nanoparticles mainly adsorbed on glassy carbon electrode. The role of electrode preparation method on reproducibility of the results is emphasized.     

亚硝酸根在磷钼镍杂多酸-聚吡咯膜修饰电极上的伏安行为及其含量测定

研究了亚硝酸根(NO     

NADH oxidation using modified electrodes based on lactate and glucose dehydrogenase entrapped between an electrocatalyst film and redox catalyst-modified polymers

We have developed a simple and efficient method for the enhanced loading of silver nanoparticles onto carbon nanospheres, and how this method can be used to design an electrochemical sensor for hydrogen peroxide (HP). A glassy carbon electrode was modified with hemoglobin, carbon nanospheres, and by enhanced loading of silver nanoparticles onto the carbon nanospheres via spontaneous polymerization of dopamine. The hemoglobin exhibits a remarkable electrocatalytic activity for the reduction of HP. The electrochemical response to HP is linear range in the 1.0–147.0?μM concentration range, with a detection limit of 0.3?μM at a signal-to-noise ratio of 3.

Simultaneous Determination of Ranitidine and Metronidazole at Glassy Carbon Electrode Modified with Single Wall Carbon Nanotubes

Single‐walled carbon nanotubes(SWCNTs) were dispersed into DMSO, and a SWCNTs‐film coated glassy carbon electrode was achieved via evaporating the solvent. The results indicated that CNT modified glassy carbon electrode exhibited efficiently electrocatalytic reduction for ranitidine and metronidazole with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the potential for reduction of selected analytes is lowered by approximately 150 mV and current is enhanced significantly (7 times) in comparison to the bare glassy carbon electrode. The electrocatalytic behavior is further exploited as a sensitive detection scheme for these analytes determinations by hydrodynamic amperometry. Under optimized condition in amperometric method the concentration calibration range, detection limit and sensitivity were about, 0.1–200 μM, detection limit (S/N=3) 6.3×10^?8 mol L^?1 and sensitivity 40 nA/μM for metronidazole and 0.3–270 μM 7.73×10^?8 mol L^?1 and 25 nA/μM for ranitidine. In addition, the ability of the modified electrode for simultaneous determination of ranitidine and metronidazole was evaluated. The proposed method was successfully applied to ranitidine and metronidazole determination in tablets. The analytical performance of this sensor has been evaluated for detection of these analytes in serum as a real sample.     

Comparison of Insulin Determination on NiNPs/chitosan‐ MWCNTs and NiONPs/chitosan‐MWCNTs Modified Pencil Graphite Electrode

The rising amount of patients suffering for diabetes mellitus increases the requirements for effective insulin sensors. Carbon materials are a suitable choice for the development of insulin sensors due to their electrochemical characteristics. Pencil graphite electrodes (PGE) represent the trade‐off between price and excellent conductive properties. The modification of PGE by NiO and Ni nanoparticles fixed by chitosan results in surface area enlargement and improved electrocatalytic properties. This paper is focused on the comparison of different properties of Ni and NiO nanoparticles and their effect on redox reaction mechanism of insulin and detection characteristics. The electrode modified by Ni nanoparticles displays linear range of 1 μM–5 μM (R² 0.80), limit of detection (LOD) of 4.34 μM and sensitivity of 0.12 μA/μM. On the other hand, the electrode modified by NiO nanoparticles displays enhanced electrochemical characteristics such as linear range of 0.05 μM–5 μM (R² 0.99), limit of detection of 260 nM and sensitivity of 0.64 μA/μM. These properties make the NiO nanoparticles modified PGE the appropriate candidate for insulin determination.