TX-100反相微乳液的缔合结构研究

对ＴＸ－１００、正戊醇、正己醇、正庚醇、正辛醇及辛烷形成的反相微乳液用ＥＳＲ自旋标记方法进行了研究，结果认为反相微乳液的形成过程伴随着表面活性剂链排列的变化，在加入水量较少时栅状区域的表面活性剂链排列拥挤，进一步的水化作用使其排列疏松。而疏水性强的探针则表明水化作用渗透到了反相微乳液的疏水区域。     

TX-100反相微乳液的缔合结构研究

对ＴＸ－１００、正戊醇、正己醇、正庚醇、正辛醇及辛烷形成的反相微乳液用ＥＳＲ自旋标记方法进行了研究,结果认为反相微乳液的形成过程伴随着表面活性剂链排列的变化,在加入水量较少时栅状区域的表面活性剂链排列拥挤,进一步的水化作用使其排列疏松。而疏水性强的探针则表明水化作用渗透到了反相微乳液的疏水区域。     

影响反相微乳液导电性能的因素

分别以聚乙二醇辛基苯基醚(Triton X-100)或十六烷基三甲基溴化铵(CTAB)为表面活性剂, 与正己烷、正己醇和水构成反相微乳液. 研究了水相H+浓度、表面活性剂、助表面活性剂等对微乳液导电性能的影响. 结果表明, 增加水相H+浓度可大幅度提高反相微乳液的导电能力, 当H+浓度由1.0 mol•L-1增加到10 mol•L-1时, 微乳液的电导率可提高1~2个数量级. 当水相H+浓度为10 mol•L-1时, 微乳液的电导率随溶水量的增大而增大, 水油体积比为3:10时, 两种体系的电导率均达到3200 μS•cm-1. Triton X-100浓度对微乳液的电导率影响较大, 电导率随其浓度增加而增大；而CTAB浓度对微乳液电导率的影响较小, 电导率随其浓度增加略有减小；助表面活性剂正己醇使非离子型反相微乳液的电导率下降, 而使阳离子型反相微乳液的电导率先增大, 然后减小, 呈骆峰状变化.     

油酸-正丙醇-水无表面活性剂反相微乳液电导研究

本文对油酸-正丙醇-水三元体系的相行为进行了研究,表明可形成微乳液.由于体系中无传统表面活性剂,故所形成的微乳液为无表面活性剂微乳液.在反相微乳液区,固定正丙醇/油酸体积比(RP/O)为3∶5、1∶1和2∶1,考察了体系电导率(κ)随分散相体积分数(φd)的变化,结果表明κ随φd的增大先缓慢增加,后急剧增大,符合渗滤特...     

微乳液相行为和微观结构的研究

用正交试验法求得阳离子表面活性剂双十八烷基二甲基氯化铵(DOD-MAC)/阴离子表面活性剂十二烷基硫酸钠(SDS)/正丁醇/正庚烷/盐水体系中相微乳液形成的最佳配方:W_(DODMAC):W_(SDS)=1:4～1:5;C_(n-butanol)%=11.0～12.0;C_(NaCl)%=3.25附近.研究了盐浓度、DODMAC和SDS复配比例、正丁醇浓度(1.0%～14.0)%以及酸种类(正丙醇、正丁醇和正戊醇)对微乳液相态、超低界面张力(γ_(mo),γ_(mw))、最佳含盐度(S)和盐宽(△S)的影响,得到了微乳液相行为的一些规律.并用FT-IR,ESR和冷冻蚀刻方法研究了中相微乳液微观结构,3种方法均表明中相微乳液随着含盐度增加,微观结构经历o/w型到B.C.再到w/o型转变.中相微乳液分子组织形态的有序分布规律,有助于构作微乳液体系的模型,有助于对中相微乳液微观结构认识及阐明微乳液微观结构与宏观特性之间关系.     

碳氢表面活性剂在超临界CO_2中形成微乳液的研究进展

在超临界CO2中形成微乳液可以克服CO2对高分子量和亲水性物质溶解能力差的缺点。碳氢表面活性剂成本低,对环境友好,利用碳氢表面活性剂形成超临界CO2微乳液有利于工业应用,但绝大部分碳氢表面活性剂不能形成微乳液,所以需要对碳氢表面活性剂进行选择和设计。本文介绍了微乳液的形成、表征和评价,从表面活性剂的亲CO2性能和界面活性两方面,综述了碳氢表面活性剂的设计思路和进展。另外介绍了助表面活性剂对形成超临界CO2微乳液的作用,并对常规碳氢表面活性剂在助表面活性剂的作用下形成超临界CO2微乳液的体系进行了综述。最后,介绍了含碳氢表面活性剂的混合表面活性剂在形成超临界CO2微乳液方面的研究情况。     

羧甲基纤维素系列高分子表面活性剂形成微乳液的研究

采用紫外光谱、相图、动态激光光散射、同位素示踪、光学显微镜、电导率等研究了羧甲基纤维素系列高分子表面活性剂与甲苯-水-异丙醇体系微乳液的形成过程,发现微乳液粒子大小均一,形态一致,其尺寸比低分子表面活性剂所形成的微乳液粒子大得多.醇分子插入到油水界面,改变了两相界面结构,促使微乳液的生成.电导率测定表明所形成的微乳液区均为水包油结构,即使在富含甲苯区域,亦不会有油包水的反相胶束形成.     

咪唑啉型表面活性剂组成微乳液的热力学性质

由咪唑啉型表面活性剂、醇、水和正十六烷组成微乳液，探讨了该微乳液中醇从油相转移到界面相时的自由能变化及温度对自由能变化的影响，算得了熵变和焓变。     

离子液体参与构筑的微乳液:离子液微乳液

微乳液一般是指两种互不相溶的液体(极性相:一般为水;非极性相:一般为有机溶剂),在表面活性剂作用下形成的均一透明的热力学稳定体系,已广泛应用于材料制备、化学合成等领域.离子液体是熔点低于100℃,完全由离子组成的一类物质,作为一种"绿色溶剂",具有诸多优异的物理化学性质,又被称为"可设计型溶剂".本文综述了离子液体作为极性相、非极性相,甚至表面活性剂,构筑的一类微乳液――离子液微乳液,重点介绍了其物理化学性质的研究进展,并展望了发展趋势.     

Enhancement of bimetallic Fe-Mn/CNTs nano catalyst activity and product selectivity using microemulsion technique

Bimetallic Fe-Mn nano catalysts supported on carbon nanotubes(CNTs) were prepared using microemulsion technique with water-to-surfactant ratios of 0.4-1.6. The nano catalysts were extensively characterized by different methods and their activity and selectivity in Fischer-Tropsch synthesis(FTS) have been assessed in a fixed-bed microreactor. The physicochemical properties and performance of the nanocatalysts were compared with the catalyst prepared by impregnation method. Very narrow particle size distribution has been produced by the microemulsion technique at relatively high loading of active metal. TEM images showed that small metal nano particles in the range of 3–7 nm were not only confined inside the CNTs but also located on the outer surface of the CNTs. Using microemulsion technique with water to surfactant ratio of0.4 decreased the average iron particle sizes to 5.1 nm. The reduction percentage and dispersion percentage were almost doubled. Activity and selectivity were found to be dependent on the catalyst preparation method and average iron particle size. CO conversion and FTS rate increased from 49.1% to 71.0% and 0.144 to 0.289 gHC/(gcat h), respectively. While the WGS rate decreased from 0.097 to 0.056 gCO2/(gcat h). C5+liquid hydrocarbons selectivity decreased slightly and olefins selectivity almost doubled.     

水包油型微乳液相色谱分离激素类药物的影响因素

采用水包油型微乳液相色谱(MELC)分离了6种激素类药物(醋酸可的松、泼尼松龙、己烯雌酚、炔雌醇、醋酸氟轻松及黄体酮)。考察了微乳流动相的组成成分(包括表面活性剂的浓度、油相种类、有机添加剂种类)及固定相孔径等对分离的影响。实验得到的最佳分离条件: 色谱柱为Venusil ASB C18 (T)(粒径5 μm,孔径30 nm,250 mm×4.6 mm),微乳流动相为30 g/L十二烷基硫酸钠(SDS)-0.8%正辛烷-6.6%正丁醇,流速为0.8 mL/min,检测波长为254 nm,柱温为35 ℃。该方法可用于甾体药物及其制剂的分离鉴别以及快速测定。     

Precipitation of hematite nanoparticles via reverse microemulsion process

Hematite nanoparticles have been successfully synthesized via two processing routes:(i) conventional precipitation route and (ii) reverse microemulsion route.The particle precipitation was carried out in a semibatch reactor.A microemulsion system consisting of water,chloroform,1-butanol and surfactant was loaded with iron nitrates to form iron nanoparticles precipitation.The precipitation was performed in the single-phase microemulsion operating region.Three technical surfactants,with different structure and HLB value are employed.The influence of surfactant characterization on the size of produced iron oxide particle has been studied to gain a deeper understanding of the important controlling mechanisms in the formation of nanoparticles in a microemulsion.Transmission electron microscopy (TEM),surface area,pore volume,average pore diameter,pore size distribution and XRD were used to analyze the size,size distribution,shape and structure of precipitated iron nanoparticles.     

SDS-正戊醇与SDS-正丁醇微乳体系相行为模拟

利用净平均曲率模型重现了以十二烷基硫酸钠(SDS)为表面活性剂,正丁醇和正戊醇为助剂,短碳链烷烃的相行为和增溶参数的变化情况。模拟了Winsor相图及最佳增溶参数曲线,并和实验进行了对比,与实验结果吻合的较好,并且发现在相同表面活性剂和助剂下,油越轻,增溶量越大,采用正戊醇做为助剂增溶轻油的能力约为采用正丁醇的3倍。在表面活性剂用量相差不大,助剂量相同的情况下,出现中相所需的盐度都是正己烷正庚烷正辛烷正十二烷,以正戊醇为助剂所需的盐度远小于以正丁醇为助剂所需的盐度。     

邻氯甲苯直接硝化法合成6-氯-3-氨基甲苯-4-磺酸

邻氯甲苯混酸硝化合成6-氯-3-氨基甲苯-4-磺酸(CLT酸)因其产率低及选择性差而未能实现工业生产,本文对该工艺进行了改进,采用酸性β沸石和乙酰硝酸酯作为催化剂和硝化剂,提高了硝化选择性和收率,分别为72％和97％;并改进了还原、异构体分离和磺化操作;CLT酸总收率提高到61％.     

微乳液相色谱法同时分离7种水溶性维生素

采用微乳液相色谱法同时分离7种水溶性维生素(V_(B1)、V_(B2)、V_(B6)、VB_(12)、叶酸、烟酰胺和VC)。考察了微乳流动相体系中表面活性剂、油相、助表面活性剂的种类以及流动相的pH值、柱温等对水溶性维生素分离的影响。优化后微乳体系的组成为:十二烷基硫酸钠(SDS)/聚氧乙烯月桂醇醚(Brij35)/正丁醇/乙酸乙酯/水(质量比为2∶60∶66∶8∶864)。色谱柱为Agilent TC C18(250 mm×4.6 mm,5μm),柱温为30℃,检测波长为254 nm,流速为0.5mL/min。7种水溶性维生素在20 min内达到基线分离。在4~36 mg/L范围内,7种水溶性维生素的质量浓度与峰面积的相关系数均大于0.999 1。不同添加水平下,V_(B1)、V_(B2)、V_(B6)、VC和烟酰胺的平均回收率为93.9%~102.9%。该方法可用于食品和药品中的多种水溶性维生素的分离、鉴别及快速测定。     

高选择性的水相苯酚羟基化反应的研究

浸渍法制备负载型氧化铜催化剂,并且采用XRD、氮气物理吸附、扫描电镜、H2-程序升温还原、热失重等手段对所得催化剂进行表征。以30%过氧化氢为氧化剂,负载型氧化铜为催化剂,将苯酚催化氧化成为苯二酚,经高效液相色谱法分析反应产物组分,发现当反应物料的摩尔比为n苯酚∶n双氧水=3∶1时,参加反应的苯酚的转化率达到25.72%,选择性(邻苯二酚)超过74%。     

Microwave promoted rapid nitration of phenolic compounds with calcium nitrate

Highly accelerated and safe nitration of phenolic compounds has been found to be feasible with a mixture of calcium nitrate and acetic acid as an efficient nitration agent under brief microwave irradiation. This method is compatible with the green chemistry approach because calcium salts—the inorganic byproducts—can be useful agrochemicals rather than waste chemicals. Commercially available ¹⁵N-labeled calcium nitrate is convenient for the preparation of ¹⁵N-labeled compounds for metabolic studies and mass spectrometry. This safe nitration method can be included in laboratory experiments for high school and college students.