Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Ultra-low expansion glass from gels

Pyrolysis of mixed titanium and silicon metal halides produces a commercial glass (7.4% TiO₂) with ultra-low thermal expansion that is essentially zero over the temperature range of 0 to 300°C. A colloidal particulate gel process involving potassium silicate, titania sol and formamide gel reagent was found to produce glass compositions with similar low expansion behavior. Due to the strongly basic nature of the precursor solutions, special titania sols had to be prepared that were stable in these alkali silicate solutions. The preferred TiO₂ sols were those containing quaternary ammonium stabilizing counter-ions. These sols served not only as the source of homogeneously distributed titania, but they may also serve as nucleating species that contribute to particle growth and pore size control of the gel network. The large pore (0.3 µm) TiO₂/SiO₂ gel structures were easily dealkalized, dried and sintered to uncracked glass shapes. Plates up to 9.5 cm×6.6 cm× 0.5 cm thick and some intricate cast shapes were produced and their glass properties evaluated.     

Effect of pore size/distribution in TiO2 films on agarose gel electrolyte-based dye-sensitized solar cells

This study develops a simple method to change the distribution of the pore size in a TiO₂ layer, using polyethylene glycol (PEG), while maintaining nearly the same surface area and porosity to clarify how large pores affect the performance of dye-sensitized solar cells (DSSCs). Specifically, a heating step at 100 °C for a specific duration is added prior to PEG removal and TiO₂ sintering at 400 °C. This process transforms the role of the PEG from a surfactant to a pore generator (porogen) and forms larger pores, depending on the loading and aggregation time for the PEG to gain larger pores. The effect of larger pores in TiO₂ films under 30 % PEG loading, on the performance of an agarose gel electrolyte-based DSSC, was further investigated using the ionic liquid, 1-allyl-3-ethylimidazolium iodide (AEII). The I–V characteristic and the electrochemical impedance spectroscopy analysis show that larger pores readily improve redox couple diffusion in a TiO₂ porous electrode and modify the interface between electrolyte and TiO₂. Using the optimized TiO₂ film with larger pores (30 % PEG loading, 100 °C/60 min), an efficiency of 7.43 % is achieved for the agarose gel electrolyte-based DSSC, which represents a 26.1 % improvement over TiO₂ without the addition of PEG.     

Studies of Capillary Porosity of Clinker Phases During Hydration

The capillary porosity of clinker phases, i.e. 3CaOSiO₂, β2CaOSiO₂, 3CaOAl₂O₃ and 4CaOAl₂O₃Fe₂O₃, at the early stages of hydration has been studied by the methods of Differential Scanning Calorimetry and nitrogen adsorption (BET). It was established that pores of 3–70 nm were formed during the hydration of 3CaOSiO₂ and the maximum of their distribution was found at about 10 nm. The hydration of 2CaOSiO₂ is much slower and the porosity is one order of magnitude lower. During the hydration of 3CaOAl₂O₃ the content of crystalline hexagonal hydrates prevailed and the porosity was in the range 5–90 nm with the average pore diameter of about 16 nm. This average pore diameter was much smaller for thermoporosimetry and lay at about 7 nm. The hydrated 4CaOAl₂O₃Fe₂O₃ sample had the porosity in the range 3–90 nm with the maximum of the pores distribution at about 4 nm. There are some differences between the porosities measured by BET and thermoporosimetry. Principally thermoporosimetry gives no information about larger capillary pores in the range 30–50 nm. This revised version was published online in July 2006 with corrections to the Cover Date.     

The Effect of an Accelerator on Cement Paste Capillary Pores: NMR Relaxometry Investigations

Nuclear Magnetic Resonance (NMR) relaxometry is a valuable tool for investigating cement-based materials. It allows monitoring of pore evolution and water consumption even during the hydration process. The approach relies on the proportionality between the relaxation time and the pore size. Note, however, that this approach inherently assumes that the pores are saturated with water during the hydration process. In the present work, this assumption is eliminated, and the pore evolution is discussed on a more general basis. The new approach is implemented here to extract information on surface evolution of capillary pores in a simple cement paste and a cement paste containing calcium nitrate as accelerator. The experiments revealed an increase of the pore surface even during the dormant stage for both samples with a faster evolution in the presence of the accelerator. Moreover, water consumption arises from the beginning of the hydration process for the sample containing the accelerator while no water is consumed during dormant stage in the case of simple cement paste. It was also observed that the pore volume fractal dimension is higher in the case of cement paste containing the accelerator.     

Preparation of TiO2 nano-particle photocatalysts by a multi-gelation method: the effect of pH change

TiO₂ photocatalysts were prepared by a multi-gelation method and the effect of the changes in the pH during the pH swing times, i.e., by a controlled pH swing, on the morphology of the TiO₂ particles was investigated. The photocatalytic properties of the TiO₂ catalysts prepared by controlled pH swing were compared with TiO₂ particles prepared without adjusting the pH during the swing times. The photocatalytic degradation reaction of these TiO₂ catalysts was investigated by comparing their effectiveness in 2-propanol oxidation. The experimental results showed that the TiO₂ photocatalysts prepared without adjusting the pH performed better in controlling the important parameters of the catalysts such as particle size, surface area, anatase/rutile phase ratio and pore size, as well as pore volume than the TiO₂ photocatalysts prepared by a controlled pH swing method. Deceased.     

TOF-GISANS investigation of polymer infiltration in mesoporous TiO2 films for photovoltaic applications

The structure of porous TiO₂ films and TiO₂:poly(N-vinylcarbazole) (PVK) composite films is investigated with time-of-flight grazing incidence small-angle neutron scattering (TOF-GISANS). The TiO₂ films have been prepared by application of a sol–gel process with a diblock copolymer as structure directing agent, and the conductive polymer PVK is infiltrated in the porous network by spin coating and solution casting. The films show a hierarchical pore structure with mesopores 52 nm in size and additional large macropores with a diameter of about 180 nm. By matching the scattering contrast of the TiO₂ with the polymer information about the penetration of the polymer in the pores is determined. Whereas in the PVK film prepared by solution casting the pores are filled to a high degree; in the spin coated film, PVK wets only the TiO₂ pore walls and forms a solid overlying layer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1628–1635, 2010     

Nano/subnano-tuning of porous ceramic membranes for molecular separation

In sol–gel processing, porous ceramic membranes can be prepared by sol-coating porous substrates and drying for gelling, followed by a firing process. Ceramic membranes prepared by sol–gel processing can be categorized into amorphous materials such as silica, and crystalline materials such as alumina and titania. Amorphous silica networks, which can be prepared by the polymeric sol route, have ultra-microporous pores that allow small molecules such as helium and hydrogen to permeate. On the other hand, crystalline materials, which are mostly prepared by the colloidal sol route, have nano-sized pores in the range of one to several nanometers. In this article, sol–gel derived SiO₂ and TiO₂ membranes with controlled pore sizes in the range of sub-nano to nanometers will be reviewed with respect to membrane preparation and to their application in the separation of the gas and liquid phases. Ceramic membranes with high performance can be obtained by precise control of membrane structures (pore size, pore size distribution, thickness, pore shape, etc.) and membrane materials (SiO₂, TiO₂, composite oxide, hybrid materials, etc.). Nano/subnano-tuning of porous ceramic membranes is quite important for the improvement of membrane permeability and selectivity.     

Degree of hydration in cement paste and C<Subscript>3</Subscript>A-sodium carbonate-water systems

This research provides a fundamental understanding of the early stage hydration of Portland cement paste, tricalcium aluminate (C₃A) paste at water to cement ratio of 0.5 and C₃A suspension at water to cement ratio of 5.0 modified by 2 or 4 mass% of sodium carbonate. A high conversion of unreacted clinker minerals to gel-like hydration products in the cement-Na₂CO₃ pastes takes place rapidly between 1^st to 24^th h. Contrary the Ca(OH)₂ formation within the same time interval is retarded in the excess of CO₃²⁻ ions due to intensive rise and growth of CaCO₃ crystals in hydrated cement. Later, the conversion of clinker minerals to the hydrate phase is reduced and higher contents of calcite and vaterite relative to that of Ca(OH)₂ in comparison with those found in the Portland cement paste are observed. As a consequence a decrease in strength and an increase in porosity between hardened Portland cement paste without sodium carbonate and those modified by Na₂CO₃ are observed. C₃A hydrates very quickly with sodium carbonate between 1^st and 24^th h forming hydration products rich in bound water and characterized also by complex salts of (x)C₃A·(y)CO₂·(zH₂O type, whereas C₃A-H₂O system offers C₃AH₆ as the main hydration product. Higher content of the formed calcium aluminate hydrates in C₃A-Na₂CO₃-H₂O system also contributes to early strength increase of Portland cement paste.     

Effects of urea on the microstructure and photocatalytic activity of bimodal mesoporous titania microspheres

Bimodal mesoporous TiO₂ microspheres with high photocatalytic activity were prepared by a hydrothermal method using titanium sulfate as precursor in the presence of urea. The results indicate that all prepared samples show bimodal pore-size distributions in the mesoporous region: smaller intra-aggregated pores with peak pore diameter of ca. 2 nm and larger inter-aggregated pores with peak pore diameter of ca. 12.5 nm. The molar ratio of urea to Ti(SO₄)₂ (R_u) has an obvious influence on the morphology, microstructure and photocatalytic activity of TiO₂. With increasing R_u, specific surface areas and porosity increase, contrarily, the crystallite size and relative anatase crystallinity decrease. The photocatalytic activity first increases with R_u. At R_u = 2.0, the photocatalytic activity reaches the highest and is obviously higher than that of Degussa P25. With further increasing R_u, the photocatalytic activity decreases. The formation rate of hydroxyl radicals during photocatalysis has a positive correlation with the photocatalytic activity.     

染料敏化太阳能电池中大孔TiO2薄膜电极的制备及应用

采用溶胶-凝胶水热法制备了TiO₂纳晶薄膜电极，晶型为锐钛矿型。为了提高电极的光电性能，利用聚苯乙烯小球做造孔剂，制备了含有大孔隙的TiO₂纳晶薄膜电极，孔径约为200 nm，该电极具有较好的光漫反射性能，更重要的是球形大孔的存在，提高了凝胶电解质在TiO₂薄膜电极中的渗透和I₃^-离子的扩散性能，与不含大孔的TiO₂电极相比，电池的短路光电流提高约2 mA·cm^-2，光电转换效率提高0.6%。     

Parameters determining efficiency and degradation of TiO2|dye|CuI solar cells

The influence of the micro-morphological structure of the TiO₂ film, the distribution of CuI in TiO₂ pores and the concentration of added surfactant in the CuI coating solution on the photocurrent of solid-state TiO₂|dye|CuI solar cells was examined by space resolved photocurrent imaging technique. Iodine is found to be competing with the oxidized dye molecules in accepting electrons from CuI and decreases the efficiency of the cell. TiO₂|dye|CuI cell degrade two hundred times faster than wet sensitization cells. This instability is considered to be due to the decomposition of the electron transfer-bridge between the sensitizer and CuI.     

Spongelike Macroporous TiO2 Monoliths Prepared from Starch Gel Template

TiO₂ materials with a hierarchical meso/macropore organization were fabricated by using titanium dioxide nanoparticles and starch gel templates. Starch sponges with high internal macroporosities were prepared by freezing and thawing of starch gels and were then infiltrated with colloidal suspensions of titania nanoparticles and air-dried to produce TiO₂-starch foams with pores up to 200 m across depending on the starch concentration and the TiO₂ loading. The TiO₂ nanoparticles were deposited as coherent layers on the thin walls of the starch framework, which was removed by calcination without significant disruption of the TiO₂ framework. The three dimensional macroporous structures of TiO₂-starch sponge composite and TiO₂ sponge induced extremely high photocatalytic activity.     

Facile one-pot synthesis of 2-arylbenzothiazoles catalyzed by H3PO4/TiO2-ZrO2 (1/1) under solvent-free conditions

A highly efficient and simple protocol for the preparation of 2-arylbenzothiazoles through condensation of 2-aminothiophenol and different aldehydes in the presence of H₃PO₄/TiO₂-ZrO₂(1/1)-cetyl pyridinium bromide (CPB) is described. The reaction proceeded under mild and solvent-free conditions to afford 2-arylbenzothiazole derivatives. In this method, the title compounds were obtained in good to excellent yields and short reaction times. The structures of synthesized products were identified by infrared, ¹H NMR, ¹³C NMR, and mass spectroscopy.     

Preparation of porous TiO2/silica composites without any surfactants

TiO₂-SiO₂ composites, with high specific surface area (up to 308 m²/g), large pore volume, and narrow distribution with average pore sizes of 3.2 nm, have been synthesized from wollastonite and titanium sulfate in the absence of any surfactants. Calcium sulfate, a microsolubility salt, plays an important role in the formation of pores in this porous TiO₂/silica composite. The microstructure and chemical composition of composite were characterized by X-ray diffractometry (XRD), transmission electron microscopy (TEM) equipped with energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectrometer (XPS) and N₂ adsorption and desorption analysis. The as-prepared porous titanium dioxide-silicon dioxide composites with high specific surface area and well-crystallized anatase contents were used as an efficient photocatalyst.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

In situ radical polymerization of methyl methacrylate in a solution of surface modified TiO2 and nanoparticles

Surface modified TiO₂ nanoparticles dissolved in toluene were encapsulated in PMMA by in situ radical polymerization of methyl methacrylate initiated by 2,2′-azobisisobutyronitrile. The surface modification of the TiO₂ nanoparticles (average diameter of 4.5 nm) was achieved by the formation of a charge transfer complex between TiO₂ nanoparticles and 6-palmitate ascorbic acid. The surface modified TiO₂/nanoparticles were characterized using UV−Vis and FTIR spectroscopy, while the obtained polymer nanocomposites were characterized using reflection and ¹H NMR spectroscopy, as well as gel permeation chromatography. The influence of the TiO₂ nanoparticles on the thermal properties of the PMMA matrix was investigated using thermo-gravimetric analysis and differential scanning calorimetry. The glass transition temperature of the polymer was not influenced by the presence of the nanoparticles while the thermal stability was significantly improved.     

荧光素掺杂的TiO2凝胶的制备及光谱研究

近些年来,溶胶－凝胶（Ｓｏｌ－Ｇｅｌ）方法作为一种软化学合成方法具有很多优点［１］,例如制作简单、烧结温度低,制得样品稳定、坚韧,制备灵活性高等。作为一种常用的染料,荧光素（ＦＬ）常用于研究非线性光学。利用Ｓｏｌ－Ｇｅｌ法可以很好地将染料分子固定在光...     

转晶纳米TiO2的制备及其声催化活性的研究

近几年兴起的半导体多相光催化技术在有机废水处理方面受到了人们的普遍关注[1,2]。众多的半导体光催化剂材料中,TiO2因其化学性质稳定和催化效率高而倍受青睐[3,4]。在紫外光的照射下,TiO2与H2O产生具有极强氧化能力的HO·自由基,最终可使废水中的有机物完全降解生成CO2,H2O以     

Preparation of nanocrystalline porous titania films on titanium substrates by a sol–gel method with polyethylene glycol as a template

Porous nanocrystalline TiO₂ films have been prepared on cp-Ti substrates for biomedical usage by a sol–gel process from the solutions containing polyethylene glycol (PEG) as a template. Variations of the crystal structure with heat-treatment temperature determined by XRD are different for TiO₂ films and powders, due to the effect of titanium substrate. The surface texture of porous TiO₂ films is analyzed by means of SEM and found to greatly depend on the concentration and molecular weight of PEG. The pore formation mechanism is discussed in relation to the self-assembly of PEG and phase separation between PEG adsorbed on TiO₂ oligomers and ethanol.