交联壳聚糖膜的制备及其性能的研究

用环氧氯丙烷成功地制备出交联壳聚糖膜。用FTIR,XRD和SEM方法表征其结构,并测试了其力学性能。结果表明,壳聚糖在低温下只有氨基参与交联反应,反应温度高于40℃时,羟基才发生反应;环氧氯丙烷的交联作用显着提高了壳聚糖膜的抗张强度,并有效地降低了溶菌酶对其降解速率;该交联膜有望用作可控降解的生物医用材料。     

多孔壳聚糖膜对醇—水体系中醛的吸附性能

研究了多孔壳聚糖膜对乙醇－水混合体系中微量醛的吸附性能。通过对影响其吸咐性能的各种因素如壳聚糖膜的制备方法。用量、醇－水体中醇浓度、酸度及其温度等的研究,认为壳聚糖适用于醇－水混合体系中微量醛的清除,并据此提出了吸附操作的优化条件。     

Novel elastomeric polyurethane fibers modified with polypropylene microfibers

Extrusion of immiscible polymer biphasic blends to form in situ microfibers of the minor component in the matrix of the major component is an elegant way to create composites with new properties. The process was used to obtain thermoplastic polyurethane elastomers modified with polypropylene microfibers. The effect of phase interaction on blend morphology and properties was studied by running a series of blends with and without a maleated polypropylene compatibilizer. Six different blends were prepared: three with compatibilizer and three without the compatibilizer. All blends contained polypropylene as a minor component (80/20; 90/10 and 95/5). Extrusion spinning of polyurethane/polypropylene blends with and without compatibilizer resulted in polyurethane fibers modified with highly-oriented polypropylene microfibrils at all component ratios. Increasing polypropylene concentration in the thermoplastic polyurethane matrix increased hardness and modulus, but did not affect tensile strength and lowered elastic recovery.     

Biobased films prepared from NaOH/thiourea aqueous solution of chitosan and linter cellulose

In the present study, films based on linter cellulose and chitosan were prepared using an aqueous solution of sodium hydroxide (NaOH)/thiourea as the solvent system. The dissolution process of cellulose and chitosan in NaOH/thiourea aqueous solution was followed by the partial chain depolymerization of both biopolymers, which facilitates their solubilization. Biobased films with different chitosan/cellulose ratios were then elaborated by a casting method and subsequent solvent evaporation. They were characterized by X-ray analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), thermal analysis, and tests related to tensile strength and biodegradation properties. The SEM images of the biofilms with 50/50 and 60/40 ratio of chitosan/cellulose showed surfaces more wrinkled than the others. The AFM images indicated that higher the content of chitosan in the biobased composite film, higher is the average roughness value. It was inferred through thermal analysis that the thermal stability was affected by the presence of chitosan in the films; the initial temperature of decomposition was shifted to lower levels in the presence of chitosan. Results from the tests for tensile strength indicated that the blending of cellulose and chitosan improved the mechanical properties of the films and that an increase in chitosan content led to production of films with higher tensile strength and percentage of elongation. The degradation study in a simulated soil showed that the higher the crystallinity, the lower is the biodegradation rate.     

海藻酸盐/壳聚糖衍生物复合抗菌纤维

通过溶液纺丝法制备海藻酸盐/羧甲基壳聚糖（CMC）共混纤维,并用红外光谱,X射线衍射和扫描电镜对共混纤维进行了表征.结果表明：共混体系中的两种组分之间存在着较强的相互作用,有良好的相容性.当ωCMC=0.30时,共混纤维的干态抗张强度达到最大值,13.8cN/tex.当ωCMC=0.10时,纤维的干态断裂伸长率可达23.1%.纤维的湿态抗张强度和断裂伸长率随着CMC含量的增加而降低.CMC的引入,可显著提高纤维的吸水率.用壳聚糖季铵盐对纤维进行处理,可赋予纤维抗菌性.     

Ionic conductivity and tensile properties of hydroxyethyl and hydroxypropyl chitosan membranes

Hydroxyethyl chitosan and hydroxypropyl chitosan were prepared through the reaction of alkali‐chitosan with 2‐chloroethanol and propylene epoxide, respectively. Fourier transform infrared and ¹³C NMR measurements were made to examine the substitution on the chitosan unit. According to a comparison of the peak areas between the modified chitosan and unmodified chitosan and the integration of peak areas of ¹H NMR spectra, for both modified chitosans, the maximum degree of substitution was less than 25%. The ionic conductivity and mechanical properties of modified chitosan membranes were investigated. In comparison with the unmodified chitosan membrane, hydrated hydroxyethyl and hydroxypropyl chitosan membranes with a higher degree of substitution showed an increase in ionic conductivity of about one order of magnitude; moreover, the crystallinity of hydroxyethyl and hydroxypropyl chitosan membranes was remarkably reduced, and their swelling indices increased significantly. However, these modified membranes did not exhibit significant changes in their tensile strength and breaking elongation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1379–1397, 2004     

Morphological and mechanical properties of nascent polyethylene fibers produced via ethylene extrusion polymerization with a metallocene catalyst supported on MCM‐41 particles

Polyethylene (PE) fibers were prepared by ethylene extrusion polymerization with an MCM‐41‐supported titanocene catalyst. The morphological and mechanical properties of these nascent PE fibers were investigated. Three levels of fibrous morphologies were identified in the fiber samples through an extensive scanning electron microscopy study. Extended‐chain PE nanofibrils with diameters of about 60 nm were the major morphological units present in the fiber structure. The nanofibrils were parallel‐packed into individual microfibers with diameters of about 1–30 μm. The microfibers were further aggregated irregularly into fiber aggregates and bundles. In comparison with commercial PE fibers and data reported in the literature, the individual microfibers produced in situ via ethylene extrusion polymerization without posttreatment exhibited a high tensile strength (0.3–1.0 GPa), a low tensile modulus (3.0–7.0 GPa), and a high elongation at break (8.5–20%) at 35 °C. The defects in the alignment of the nanofibrils were believed to be the major reason for the low modulus values. It was also found that a slight tensile drawing could increase the microfiber strength and modulus. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2433–2443, 2003     

Thermal and mechanical properties of UV irradiated collagen/chitosan thin films

The thermal and mechanical properties of collagen/chitosan blends before and after UV irradiation have been investigated using thermal analysis and mechanical (Instron) techniques. Comparisons were made with the thermal and mechanical properties of both collagen and chitosan films. Air-dried collagen, chitosan and collagen/chitosan films were exposed to UV irradiation (wavelength 254 nm) for different time intervals. Thermal properties of collagen/chitosan blends depend on the composition of the blend and are not significantly altered by UV irradiation.Mechanical properties such as ultimate tensile strength and ultimate percentage of elongation were much better for collagen films than for collagen/chitosan films. The results have shown that the mechanical properties of the blends were greatly affected by the duration of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the blend. Increasing UV irradiation leads to an increase in Young's modulus of the collagen/chitosan blend.     

Effects of curing agents and modified graphene oxide on the properties of XNBR composites

This paper investigates the effects of crosslinking methods on the incorporation of graphene oxide (GO) in carboxylated nitrile butadiene rubber (XNBR) in the process of producing nanocomposites for chemical-resistant protective clothing and gloves. The novel aspect of the study is a comprehensive approach involving both unmodified GO as well as GO that was carboxylated to increase its affinity to XNBR and to facilitate its application. The nanostructure of XNBR composites was characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Fourier transform infrared spectroscopy (FTIR) was used to elucidate the chemical structure of the composites. Thermal stability studies were performed using differential scanning calorimetry (DSC). The barrier properties of the composites were determined based on swelling, crosslinking density, and permeation by mineral oils. The mechanical tests included resistance to puncture and abrasion, stress at strain, and tensile strength. Contact angle was measured to determine the degree of hydrophobicity of the obtained composites.AFM and SEM images revealed the effects of different curing agents (sulfur, magnesium oxide, or a hybrid system) as well as GO type on the surface morphology of XNBR composites. The type of curing agent was found to affect the kind of crosslinks formed and their spatial network structure, as confirmed by FTIR. The DSC curves showed that the crosslinking methods of XNBR did not affect glass transition temperature, but led to large changes observed in the temperature range of 130–220 °C.The type of crosslinking method affected the degree of swelling. It was found that the incorporation of carbon nanofillers led to an improvement in the abrasion and puncture resistance as well as tensile strength of XNBR composites. The water contact angle of the composites indicated hydrophobicity. The properties of XNBR composites containing GO revealed their substantial application potential in protective clothing.     

Effects of annealing and the addition of PEG on the PVA based hydrogel by gamma ray

Poly(vinyl alcohol) (PVA) is an interesting material with good biocompatibility, high elasticity and hydrophilic characteristics. PVA hydrogels have been formed through chemical crosslinking with aldehyde, photopolymerization and physical crosslinking with freeze-thawing. In this study, crosslinked hydrogels based on PVA, and poly(ethylene glycol) (PEG) were prepared by gamma-ray irradiation, and then annealed at 120 °C. The properties of a hydrogel such as gel fraction, swelling behavior, gel strength as a function of PEG content and annealing time were investigated. Also, the thermal behaviors were examined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The gel fraction decreases with an increase in PEG content and decrease in annealing time. The tensile strength increases with an increase in annealing time. The thermal behaviors have shown different patterns according to the annealing time. The improved properties suggest that PVA/PEG blend hydrogel can be a good candidate for applications in the articular cartilage.     

A NOVEL APPROACH TO SYNTHESIZE CHITOSAN BEADS CROSSLINKED BY EPICHLOROHYDRIN

1. INTRODUCTION Chitosan is the deacetylated chitin which is one of the most abundant natural polymers produced from crab, lobster and shrimp shells or fungal fermentation processes [1]. It is a family of deacetylated β1→4 D-glucosamine polymers. Chitosan has properties including bioactivity, biocompatibility and biodegradability, so it is potentially more useful than cellulose for developing advanced of attention not only as an unutilized biomass resource but also as a novel type of sp…     

Fabrication,characterization and in vivo evaluation of dexpanthenol sustained-release nanofibers for wound healing

In this study, wound dressings consisting of dexpanthenol (Dex)-loaded electrospun nanofibers were fabricated using polyvinyl alcohol (PVA)/sodium alginate (SA), and chitosan as the core and the shell, respectively. Considering the remarkable properties of chitosan, it was used as a shell against drug release and to improve the thermal stability, and tensile strength of the scaffold. By comparing the thermogravimetric, and tensile strength results of nanofibers with and without shell, it was revealed that the presence of chitosan in the shell side could improve the thermal stability and increased the tensile strength by about three times. The isotherm models of dexpanthenol release from the PVA/SA/Dex-CS scaffold was best described by the Langmuir model. Besides, Fourier transform infrared, scanning electron microscopy, and X-ray diffraction techniques were performed to characterize nanofibers. Furthermore, an in vivo investigation of a wound dressing with dexpanthenol showed better healing compared to the wound dressings without dexpanthenol.     

A NOVEL APPROACH TO SYNTHESIZE CHITOSAN BEADS CROSSLINKED BY EPICHLOROHYDRIN

The present investigation describes a novel method for preparing spherical chitosan particles based on crosslinking with epichlorohydrin.Certain amount of pre-crosslinking agent was added to form chitosan gels by traditional inverse phase suspension polymerization.Then the gels were crosslinked by epichlorohydrin at basic condition to obtain chitosan beads.The effects of reaction conditions,such as crosslinking time,the amount of crosslinking agent and the NaOH concentration,on the physical properties of the chitosan beads were investigated.The beads were found to have more amino groups in the polymer chains than the beads crosslinked by glutaraldehyde.The capacity for copper ions in as high as 40mg/g,The beads have good mechanical strength and can be reused.     

Dialdehyde starch‐crosslinked chitosan films and their antimicrobial effects

For improved mechanical and water‐swelling properties of chitosan films, a series of transparent films were prepared with dialdehyde starch as a crosslinking agent. Fourier transform infrared and X‐ray analysis results demonstrated that the formation of Schiff's base disturbed the crystallization of chitosan. The mechanical properties and water‐swelling properties of the films were significantly improved. The best values of the tensile strength and breaking elongation were 113.1 MPa and 27.0%, respectively, when the dialdehyde starch content was 5%. All the crosslinked films still retained obvious antimicrobial effects toward S. aureus and E. coli, and they showed potential for biomedical applications. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 993–997, 2003     

Preparation and Characterization of Chitosan Composite Membranes Crosslinked by Carboxyl-capped Poly（ethylene glycol）

In this study a series of chemically crosslinked chitosan/poly（ethylene glycol） （CS/PEG） composite membranes were prepared with PEG as a crosslinking reagent other than an additional blend. First, carboxyl-eapped poly（ethylene glycol） （HOOC-PEG-COOH） was synthesized. Dense CS/PEG composite membranes were then prepared by casting/evaporation of CS and HOOC-PEG-COOH mixture in acetic acid solution. Chitosan was chemically crosslinked due to the amidation between the carboxyl in HOOC-PEG-COOH and the amino in chitosan under heating, as confirmed by FTIR analysis. The hydrophilicity, water-resistance and mechanical properties of pure and crosslinked chitosan membranes were characterized, respectively. The results of water contact angle and water absorption showed that the hydrophilicity of chitosan membranes could be significantly improved, while no significant difference of weight loss between pure chitosan membranes and crosslinked ones was detected, indicating that composite membranes with amidation crosslinking possess excellent water resistanance ability. Moreover, the tensile strength of chitosan membranes could be significantly enhanced with the addition of certain amount of HOOC-PEG-COOH crosslinker, while the elongation at break didn＇t degrade at the same time. Additionally, the results of swelling behaviors in water at different pH suggested that the composite membranes were pH sensitive.     

Water absorption and degradation characteristics of chitosan-based polyesters and hydroxyapatite composites

Blends of chitosan and biodegradable synthetic aliphatic polyesters (polycaprolactone, poly(butylene succinate), poly[(butylene succinate)-co-adipate], poly[(butylene terephthalate)-co-adipate], and poly(lactic acid)) were injection-molded. These samples were immersed in isotonic solution at 37 degrees C for a period of 60 d. The water uptake and the degradation properties, as measured by the loss in tensile strength, were evaluated as a function of time. In this study, the rate and the equilibrium water uptake were proportional to the amount of chitosan in the blend. The addition of HA to chitosan and polyester significantly reduced the equilibrium water uptake. The water uptake did not follow the classical Fickian phenomena and could be expressed by a two-stage sorption non-Fickian diffusion model. Contact angle measurement was used to quantify the changes in surface hydrophilicity as a function of chitosan and polyester composition. The glycerol contact angle decreased with increasing synthetic components in the blend. The blends and composites also showed increased degradation, as quantified by a loss in their mechanical properties, with increase in natural content. The degradation of properties was directly related to the water uptake of the blends; the higher the water uptake, the higher the degradation. Pure polyesters, while having low water uptake, nevertheless showed significant degradation by a precipitous drop in the strain at break. Among the polyesters, poly(lactic acid) displayed maximum degradation, while polycaprolactone displayed the least.     

光交联壳聚糖膜的制备及其性能研究

成功制备了光交联壳聚糖膜,并用傅立叶红外光谱(FTIR)和扫描电子显微镜(SEM)方法对其结构进行了表征,并测试了其力学性能。结果表明:光交联作用明显提高了膜的抗张强度和抗水性,并有效地降低了溶菌酶对其降解速率。该光交联膜有望用作可控降解生物医用材料。     

Effects of Neutralization Process on Preparation and Characterization of Chitosan Membranes for Wound Dressing

Summary: Neutralization process effects on preparation and characterization of chitosan membranes were evaluated by differencial scanning calorimetry and scanning electron microscopy. Water solubility and humidity of chitosan membranes were also studied. Swelling behavior in different pH media was evaluated and mechanical properties such as tensile strength and elongation at break were measured. Neutralization process increased glass transition temperature of chitosan membranes and decreased their water solubility, humidity and water sorption. An improvement in mechanical properties of chitosan membranes was also observed after neutralization process.     

The Effects of Demineralization Process on Diameter,Tensile Properties and Biodegradation of Chitosan Fiber

Chitosan fiber is one of the potential fibers that can be used as absorbable monofilament suture in biomedical application. In chitosan synthesis, aside from deproteination and deacetylation, demineralization is a crucial step where the major minerals within crustacean shells are removed. This demineralization process is carried out with two parameters, i.e. time and temperature. This research studies the influence of demineralization time on the diameter, tensile properties and biodegradability of chitosan fibers. Chitosan was synthesized from shrimp shells using 1 × 2 h and 3 × 2 h demineralization process. Chitosan fibers were produced by means of wet spinning. The chemical properties of chitosan fibers were characterized by means of Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffractometry (XRD) technique. Physical properties characterization was carried out to measure the fibers’ diameter, density and viscosity. Tensile properties were evaluated by means of tensile test. The results were compared to standard of absorbable suture from the United States Pharmacopoeia (USP). Furthermore, in vitro degradation testing was also performed for analyzing biodegradation properties. Chitosan fibers were successfully made with diameter and maximum tensile force of chitosan fibers in a range of 364 - 460 μm and 5.6 - 8.3 N, respectively. The results of this research pointed that adding demineralization time would increase the diameter of chitosan fiber. However, the degradation occurred in prolonged demineralization process broke the bonds within the fiber which lead to a decrease in fiber's density. It is due to the degradation of chitosan occurred during extended demineralization process, which leads to degree of crystallinity reduction. Extensive demineralization process has been found to lower fibers’ tensile strength from 80.4 MPa to 38.4 MPa (52.2%), but increase their biodegradability by 17% and maximum elongation from 6.9% to 16.2% (136%). Despite that extensive demineralization process lowered chitosan fiber's tensile strength, both fibers made could still fit the standard for synthetic absorbable suture from USP number 0 and 1.     

Properties of isocyanurate-type crosslinked polyurethanes

Polyurethane elastomers containing isocyanurate rings as crosslinking structure were prepared by crosslinking the prepolymers in N,N-dimethylformamide solution with sodium cyanide catalyst. Physical properties such as gel fraction, swelling ratio, density, glass transition temperature, Young's modulus, tensile strength, and elongation at break were measured. The effects of diisocyanate structure, the degree of crosslinking, and the crosslinking structure on the properties of polyurethanes were studied. The stress–strain curves of isocyanurate-type crosslinked polyurethanes prepared from poly(oxytetramethylene)glycol rose at lower extensions and gave higher tensile properties than those of triol-cured and diamine-cured polyurethanes. The observed high tensile properties were attributed to the rigid crosslinking structure of isocyanurate ring.