Leaching of lead silicate glasses in acid environment: compositional and structural changes

Lead silicate glasses (45.3 weight % of lead oxide) were leached in aqueous static solutions of HNO₃ at pH=2 and T=90 °C for different leaching times, to study the weathering mechanism of lead glasses in an acidic environment.The leached surface was analysed by different analytical techniques like RBS (Rutherford backscattering spectrometry), XPS (X-ray photoelectron spectroscopy) and SEM-EDS (scanning electron microscopy-energy dispersive spectrometry). Even the leaching solutions were analysed by ICP-AES (inductively coupled plasma-atomic emission spectroscopy) to measure the amount of lead and other ions that migrate from the glass to the solution.The results obtained show that the leached layer, depleted of lead and alkaline ions, is some hundreds of nanometres thick. It is about ten times thinner than the one obtained on richer glasses (66 weight % of lead oxide), but the kinetics of the leaching process is exactly the same: a stabilisation takes place after two days of leaching and a Pb-enriched surface thin layer (a few nanometres thick) is formed. PACS 61.85; 33.60.F; 79.60.-i; 61.43.F; 61.16.B; 68.35.B     

二价碱土金属氟化物对Er3+/Tm3+/Yb3+共掺氟氧锗酸盐玻璃热稳定性和光谱特性影响的研究

制备了分别含有MgF2,CaF2,SrF2或BaF2的Er3+/Tm3+/Yb3+共掺氟氧锗酸盐玻璃试样和包含BaF2纳米晶的玻璃陶瓷试样,所制备试样均具有良好的透光性。对试样的热稳定性和上转换发光特性进行了研究。通过分析试样的吸收光谱发现,随着所含二价阳离子原子量的增大,试样的紫外吸收截止波长明显向短波方向移动。结果显示:通过改变所含二价碱土金属离子的种类能够对激发光的颜色进行调节,特别值得关注的是Mg2+的影响;结果证实:通过对包含二价碱土金属的玻璃进行微晶化处理或者增加二价碱土金属的含量均能提高上转换发光的强度。     

Surface modification of polyvalent element-containing glasses

Seven soda-lime silicate glasses, each of which contains one of the following polyvalent metals: Fe, Mn, Cu, Ce, Ti, V, and Cr, are oxidized in air and reduced in H₂/N₂ (1/99) at their respective glass transition temperature for some period. A crystalline oxide surface layer is created on the glasses (except the vanadium-bearing glass) under the oxidizing condition, since the metallic ions are oxidized from lower to higher valence state, and thereby calcium ions diffuse outward and react with oxygen ions. In contrast, a silica-rich surface layer is created on the glasses under the reducing condition, since sodium and calcium ions diffuse inward. It is found that the extents of both outward and inward diffusions strongly depend on the type of the polyvalent ions for the same conditions of heat-treatment. Out of the seven polyvalent metals studied in this work, copper induces the highest extent of both the inward and outward diffusion, and hence, the thickest surface layer of both amorphous silica and crystalline alkaline earth oxides. The oxide layer lowers the onset temperature of the primary crystallization. The silica-rich surface layer enhances the chemical resistance of the glass in a hot basic solution.     

Detection of Fe3+ and Hg2+ Ions by Using High Fluorescent Carbon Dots Doped With S And N as Fluorescence Probes

In this paper, carbon quantum dots (N-S-CDs) containing sulfur and nitrogen were synthesized using citric acid and thiourea. The average particle size of N-S-CDs is 8 nm. The N-S-CDs surface contains various of functional groups, which has good water solubility. The fluorescence quantum yield of N-S-CDs is as high as 36.8%. N-S-CDs emits strong blue fluorescence in aqueous solution and has good photostability in neutral and alkaline NaCl solution. N-S-CDs has unique selectivity and high sensitivity to Fe³⁺ and Hg²⁺ ions, and the lowest detection limits are 1.4 μM and 0.16 μM, respectively. Under the interference of other metal ions, Fe³⁺ and Hg²⁺ ions can still effectively and stably quench the fluorescence of N-S-CDs. In addition, in the detection of actual samples, N-S-CDs can effectively detect Fe³⁺ and Hg²⁺ ions in tap water and lake water.

     

Self- and foreign alkaline-earth diffusion in mixed cation silicate glasses

Self-diffusion of alkaline-earth ions in various mixed cation silicate glasses of the composition A₂O·2MO·4SiO₂ was investigated by radiotracer diffusion measurements below the respective glass transition temperatures. Including previous measurements, we have analyzed the diffusivity of divalent ions in mixed cation systems with A = Li, Na, K, Cs and M = Ca, Sr, Ba. The activation enthalpy depends strongly on the type of cations, revealing an increasing diffusivity for glasses with cations of similar size. The behavior is consistent with mechanical loss spectroscopy measurements performed on the same glasses. In addition foreign atom diffusion of calcium and barium in strontium containing glasses were performed. In the case the ionic radius of the alkali ions exceeds that of the alkaline-earth ions the diffusion activation enthalpy of the foreign ion equals the activation enthalpy of self-diffusion. The results can be described on the basis of a theoretical model proposed by Kirchheim [R. Kirchheim, J. Non-Cryst. Solids 328 (2003) 157] that relates the activation enthalpy to electrostatic and elastic contributions.     

Role of cleaning methods on bond quality of Ti coated glass/imidex system

Thin film materials are widely used in the fabrication of semiconductor microelectronic devices. In thin film deposition, cleanliness of substrate surface have become critically important as over 50% of yield losses in integrated circuit fabrication are caused by microcontamination [1]. There are many wafer cleaning techniques. The most successful approach for silicon wafer cleaning technique is RCA clean [2]. But for glass substrate it is still not known which procedure of cleaning is the best. This paper provides an understanding of the right way of glass wafer cleaning method, with a focus towards identifying good bond strength. Two wafer cleaning techniques have been used for cleaning glass substrates in the context of laser micro-joining of dissimilar substrates. First cleaning procedure involves two steps, first cleaning in acetone solution and then in DI water solution. After each step dried with N₂. Second cleaning procedure involves four steps, first cleaning with 1% Alconox solution, second in DI water, third in acetone solution and finally in a methanol solution and dried with N₂ after each step. Deposition of Ti thin film on top of these two types of substrate using DC magnetron sputtering method also showed better adhesion of Ti film on glass for the second type of cleaning method. Scanning electron microscopy (SEM) analyses of the lap shear tested failed surfaces for these two kinds of samples revealed strong bond for samples prepared by second cleaning method compared to first cleaning method. Characterization of these two sets of samples using X-ray photoelectron spectroscopy (XPS) has shown excellent contamination removal for the second cleaning method. This modification is believed to be due to reduction of carbon contamination.     

碱金属和碱土金属氟化物对掺Er3+氟磷酸盐玻璃光谱性质的影响

研究了碱金属和碱土金属离子修饰的掺Er^３＋氟磷酸盐玻璃的光谱性质，讨论 了碱金属和碱土金属对铒氟磷玻璃的吸收和发射截面、荧光半高宽，Judd-Ofelt强度参数和 上转换发光强度等光谱性质的影响，并与一些传统氧化物玻璃系统进行了比较.研究表明碱 金属K^＋和碱土金属Sr^２＋掺杂高的玻璃更适宜用作光放大器基质. 含12mol％K^＋的氟磷玻璃展现出7.83×10^-21cm^２的高 发射截面和最小的荧光上转换强度；含23mol％Sr^２＋的氟磷玻璃则有7.58×10 ^-21cm^２的高发射截面、65nm的荧光半高宽及8.6ms的长的上能级荧 光寿命. 关键词： 氟磷酸盐玻璃 光谱性质 Judd-Ofelt参数 光学放大器     

Analyses of HF/NH4F buffer-treated Si(111) surfaces using XPS,REM and SIMS

The effect of different cleaning procedures on Si(111) wafers has been studied. A three-step cleaning process was used. The first two steps (thermal oxidation followed by RCA cleaning) were common to all samples. The final step involved rinsing in one of a set of HF/NH4F buffer solutions with a wide range ofpH values. Three different surface techniques were used for characterizing the chemical condition and morphology of the treated surfaces: XPS (X-ray Photoemission Spectroscopy), REM (Reflection Electron Microscopy) and SIMS (Secondary-Ion Mass Spectroscopy). It has been found that thepH value of an HF solution does significantly affect the etching rate and morphology of the Si(111) surface: For the same type of solution, the smaller thepH value, the higher the etching rate. Basic solutions withpH values larger than eight have a much weaker etching effect on the surface, which is contradictory to some previous reports. The most effective solutions for the etching of the Si(111) surface are the solutions of HF buffered by NH₄F, with thepH in the range of 2–6. REM images indicate that the surface morphology after etching in the HF solution is strongly affected by the length of the etching time: Overetching will roughen the surface. The SIMS data show that water rinsing in air during the cleaning process does speed up oxidation, but it is necessary to use water to clean off the residuals from the HF solutions.     

Ionic conductivity of alkaline (Li2O, Na2O) and alkaline-earth (BaO) borates in crystallization (vitrification) region

In this paper we report the existence of abnormal behavior of electric properties of alkaline (Li₂O,Na₂O) and alkaline-earth (BaO) borate in the melt—a crystal (glass) transition region. Results of measurement of conductivity in the mentioned interval evidence the existence of a strong variation of electric properties depending on the concentration of alkaline and alkaline-earth ions. The reasons of such behavior are discussed.     

Si cleaning method without surface morphology change by cyanide solutions

Hydrogen cyanide (HCN) aqueous solutions can remove copper contaminants from Si surfaces more effectively than hydrochloric acid/hydrogen peroxide mixture (HPM) and sulfuric acid/hydrogen peroxide mixture (SPM). When pH of the HCN solutions is adjusted at 9, Si surface morphology is not changed, while when pH exceeds 10, the Si surfaces are considerably roughed. AFM measurements show that Cu contaminants are present in the form of particles on the bare Si surfaces. XPS measurements show that the particles consist of metallic Cu. The Cu particle height decreases almost linearly with the cleaning time, and the Cu surface concentration decreases exponentially with it. It is concluded that Cu particles gradually dissolve into the HCN aqueous solutions by the direct reaction with cyanide ions at the surface of the Cu particles.     

X-ray photoelectron spectroscopy of CeO2–Na2O–SiO2 glasses

A series of (CeO₂)_x–(Na₂O)_0.3–(SiO₂)_(0.7−x) glasses, where 0.025 ≤ x ≤ 0.075, have been synthesized and investigated by mean of X-ray photoelectron spectroscopy (XPS). The Ce 3d spin-orbit doublet was curve fitted in order to quantify the proportions of each cerium oxidation state in these glasses. It was found that Ce ions are predominantly in the Ce(III) state in glasses with compositions x ≤ 0.075, while mixed Ce valences were found in the glass with composition x = 0.10. The O 1s spectra have also been curve fitted with two components, one from bridging oxygen (BO) and the other from non-bridging oxygen atoms (NBO). The measured number of NBO, based on the fact that only oxygen atoms in the site Si–O–Na⁺ contribute to the NBO peak, was found to be constant at ∼35% for all samples, in good agreement with the value calculated from the glass composition and inductively coupled plasma (ICP) suggesting that Ce ions enter the network as a glass intermediate. The thermal measurements done on these glasses agree well with the XPS findings.     

氮掺杂碳量子点的合成及作为荧光探针对Hg~(2+)的检测

与传统量子点相比,碳量子点作为一种新型的荧光碳纳米材料,由于其良好的生物相容性、易于表面功能化、低毒性等优点受到了广泛关注。采用柠檬酸为碳源,氨水为氮源,热解法制备出水溶性好的氮掺杂碳量子点(NCDs)。透射电镜(TEM)观察NCDs的粒径在3nm左右;X射线光电子能谱(XPS)和傅里叶红外光谱(FIIR)证明NCDs的表面被羧基、氨基、羟基、羰基等官能团功能化,说明NCDs有很好的水溶性。研究还发现Hg~(2+)对NCDs的荧光有良好的猝灭作用,可作为荧光探针检测水中Hg~(2+)含量。在PBS缓冲液中(0.1mol·L~(-1) pH 7.0),NCDs的荧光猝灭率(F/F0)与汞离子浓度在0.001~0.1μmol·L~(-1)之间存在良好的线性关系,检出限为2.1nmol·L~(-1)。该方法灵敏度高、选择性好、方法简便,可应用于Hg~(2+)快速、灵敏的检测。     

Redox reactions and inward cationic diffusion in glasses caused by CO and H2 gases

We find that inward diffusion of network-modifying cations can occur in an iron-containing silicate glass when it is heat-treated in CO/CO₂ (98/2 v/v) or H₂/N₂ (1/99 v/v) gases at temperatures around the glass transition temperature. The inward diffusion is caused by the reduction of ferric to ferrous ions and this diffusion leads to formation of a silica-rich surface layer with a thickness of 200–600 nm. The diffusion coefficients of the network-modifying divalent cations are calculated and they are different for the glasses treated in the CO and H₂ gases. At the applied partial pressures of CO and H₂, the H₂-bearing gas creates the silica-rich layer more effectively than the CO-bearing gas. The layer increases the hardness and chemical durability of the glass due to the silica network structure in the surface layer.     

Ion-beam depth-profiling studies of leached glasses

Ion-beam depth-profiling was carried out on three different glasses leached (or hydrated) in deionized water using ¹H(¹⁹F, αγ)¹⁶O nuclear reaction, secondary ion mass spectrometry (SIMS), and sputter-induced photon spectrometry (SIPS) techniques. The depth-profiles show an interdiffusion mechanism in which the sodium ions in the glass are depleted and replaced by hydrogen (H⁺) or hydronium (H₃O⁺) ions from the solution. The leaching behavior does not show significant difference whether the glass surface is fractured or polished. Problems of mobile ion migration caused by ion bombardment and loss of hydrogen during analysis are discussed.     

Surface cleaning procedures for thin films of indium gallium nitride grown on sapphire

Surface preparation procedures for indium gallium nitride (InGaN) thin films were analyzed for their effectiveness for carbon and oxide removal as well as for the resulting surface roughness. Aqua regia (3:1 mixture of concentrated hydrochloric acid and concentrated nitric acid, AR), hydrofluoric acid (HF), hydrochloric acid (HCl), piranha solution (1:1 mixture of sulfuric acid and 30% H₂O₂) and 1:9 ammonium sulfide:tert-butanol were all used along with high temperature anneals to remove surface contamination. X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) were utilized to study the extent of surface contamination and surface roughness, respectively. The ammonium sulfide treatment provided the best overall removal of oxygen and carbon. Annealing over 700 °C after a treatment showed an even further improvement in surface contamination removal. The piranha treatment resulted in the lowest residual carbon, while the ammonium sulfide treatment leads to the lowest residual oxygen. AFM data showed that all the treatments decreased the surface roughness (with respect to as-grown specimens) with HCl, HF, (NH₄)₂S and RCA procedures giving the best RMS values (∼0.5-0.8 nm).     

X-ray photoelectron spectroscopy of Sm-doped CaO-MgO-Al2O3-SiO2 glasses and glass ceramics

Sm³⁺ doped CaO-MgO-Al₂O₃-SiO₂ glass and glass ceramics have been prepared. The diopside crystal (CaMgSi₂O₆) was identified in the glass ceramics by X-ray diffraction analysis. X-ray photoelectron spectra of the glass and glass ceramics were measured by a monochromatised Al-Kα XPS instrument. Sm 3d core level spectra for the Sm doped samples showed that Sm ions are predominantly in the Sm (III) state in glass and glass ceramics. The O 1s core spectra could be fitted by summing the contributions from bridging oxygen (BO) and non bridging oxygen (NBO) for samarium undoped glass, BO, NBO and Si-O-Sm for the doped glass. The O 1s XPS spectrum of undoped glass ceramics was curve fitted with BO and NBO in glass phase, as well as SiOSi, SiOMg and SiOCa in diopside. In addition to the five components above mentioned, SiOSm in diopside also appeared in O 1s XPS spectra of samarium doped glass ceramics. According to the fitting results, we demonstrate that the Sm₂O₃ exist in glass network as a glass modifier. After heat treatment, nearly all the Sm³⁺ existed in diopside phase as the substitution for Ca²⁺.     

Planar waveguides in multicomponent glasses fabricated by field-driven differential drift of cations

The fabrication of planar waveguides by a constant-current thermal poling procedure in multicomponent glasses rich in alkali or alkaline earth ions is described. Near the anode, the dc electric field applied to the substrate separates the mobile cations into regions according to their mobility. Each region presents a different refractive index, allowing a waveguide to be formed. This method produces waveguides with an index increase greater than 10(-2) in soda-lime glass with no external ion source, and the waveguides are buried beneath the substrate surface without an additional step.     

Compositional dependence of in-vitro bioactivity in sodium calcium borate glasses

Borate glasses with composition xCaO (100−x) B₂O₃ (20≤x≤50), where x is in mole percent) and 50CaO·45B₂O₃·5Na₂O have been prepared using conventional melt quench technique. Samples were submerged in simulating body fluid solution (SBF) at 37 °C for various periods of time. After storage the samples were analyzed in order to investigate if a surface layer of hydroxyl carbonate apatite layer (HCA layer/Ca-P layer) had formed. The analysis technique used included Fourier-Transform Infrared Spectroscopy (FTIR). The rate of HCA layer formation on the surface of exposed glass samples is determined by FTIR, percentage weight loss measurements of glass samples in SBF and variation of pH of SBF as a function of time. Increase in calcium content in the glass matrix has shown to decrease the rate of HCA formation on glass surfaces. The borate glass with x=20 has shown HCA layer formation on glass surface within two days of dipping. The bone like apatite formation of glass surface demonstrates the potential of glass for integration with bone.     

Method for additional purification of the surface of Si(111) single crystal

A method for additional purification of the surface of single crystals of semiconductors is developed, which consists in the preliminary cleaning of samples by thermal heating in combination or without ion etching in ultrahigh vacuum, followed by implantation with low-energy Ba⁺ ions (or ions of other alkaline elements) and their successive removal by brief (1 min) high-temperature (T = 1550 K) thermal heating. The effect of additional purification is achieved by the fact that the embedded ions of Ba⁺ or other alkaline elements, being active, form compounds with impurity atoms (O, C, S, N, etc.) and are removed during hightemperature heating.     

TEM monitoring of silver nanoparticles formation on the surface of lead crystal glass

Silver nanoparticles have been formed on the surface of lead crystal glass by means of (i) ion-exchange of alkaline ions from the glass by Ag⁺ ions from a molten salts bath, and (ii) silica based sol-gel coatings containing silver. All experimental variables concerning both ion-exchange process and sol-gel coatings application were combined and studied as main parameters governing the reduction of Ag⁺ ions to Ag⁰ atoms and further aggregation to form nanosized colloids. The content of thermoreducing agents (arsenic or antimony oxides) in the lead crystal glass was essential to favour the reduction of silver ions to form nanoparticles. Optimal experimental conditions to be used for the obtaining of surface silver nanoparticles were determined. TEM was used as the principal characterisation technique for direct observation of the nanoparticles generated. The size of silver colloids varied in the 20-300 nm range for ion-exchanged samples and in the 10-80 nm range for sol-gel coated samples.