Preconcentration and speciation of inorganic and methyl mercury in waters using polyaniline and gold trap-CVAAS

Applicability of polyaniline (PANI) has been investigated for the preconcentration and speciation of inorganic mercury (Hg²⁺) and methyl mercury (CH₃Hg⁺) in various waters (ground, lake and sea waters). Preliminary experiments (batch) with powdered PANI for the quantitative removal of both Hg²⁺ and CH₃Hg⁺ showed that the retention of Hg²⁺ was almost independent of pH while a pH dependent trend from pH 1 to 12 was seen for CH₃Hg⁺ with maximum retention at pH > 5. Time dependence batch studies showed that a contact time of 10 min was sufficient to reach equilibrium. The K_d values were found to be ∼8 × 10⁴ and ∼7 × 10³ for Hg²⁺ and CH₃Hg⁺, respectively.Subsequently column experiments were carried out with PANI and the separation of the species was carried out by selective and sequential elution with 0.3% HCl for CH₃Hg⁺ and 0.3% HCl-0.02% thiourea for Hg²⁺. This was then followed by further pre-concentration of mercury on a gold trap and its determination by CVAAS. The uptake efficiency studies showed that the PANI column was able to accumulate up to 100 mg Hg²⁺/g and 2.5 mg CH₃Hg⁺/g. This method allows both preconcentration and speciation of mercury with preconcentration factors around 120 and 60 for Hg²⁺ and CH₃Hg⁺, respectively. The interfering effects of various foreign substances on the retention of mercury were investigated.     

Non-chromatographic speciation analysis of mercury by flow injection on-line preconcentration in combination with chemical vapor generation atomic fluorescence spectrometry

A novel non-chromatographic approach for direct speciation of mercury, based on the selective retention inorganic mercury and methylmercury on the inner wall of a knotted reactor by using ammonium diethyl dithiophosphate and dithizone as complexing agents respectively, was developed for flow injection on-line sorption preconcentration coupled with chemical vapor generation non-dispersive atomic fluorescence spectrometry. With the sample pH kept at 2.0, the preconcentration of inorganic mercury on the inner walls of the knotted reactor was carried out based on the exclusive retention of Hg–DDP complex in the presence of methylmercury via on-line merging the sample solution with ammonium diethyl dithiophosphate solution, and selective preconcentration methylmercury was achieved with dithizone instead of ammonium diethyl dithiophosphate. A 15% (v/v) HCl was introduced to elute the retained mercury species and merge with KBH₄ solution for atomic fluorescence spectrometry detection. Under the optimal experimental conditions, the sample throughputs of inorganic mercury and methylmercury were 30 and 20 h^− 1 with the enhancement factors of 13 and 24. The detection limits were found to be 3.6 ng l^− 1 for Hg²⁺ and 2.0 ng l^− 1 for CH₃Hg⁺. The precisions (RSD) for the 11 replicate measurements of each 0.2 μg l^− 1 of Hg²⁺ and CH₃Hg⁺ were 2.2% and 2.8%, respectively. The developed method was validated by the analysis of certified reference materials (simulated natural water, rice flour and pork) and by recovery measurements on spiked samples, and was applied to the determination of inorganic mercury and methylmercury in biological and environmental water samples.     

Removal of complexed mercury by dithiocarbamate grafted on mesoporous silica

Mesoporous silica (MCM-41) with d ₍₁₀₀₎ interplanar distance of 38 Å was prepared by a room temperature process through low surfactant templation technique. The surface of MCM-41 was functionalized with dithiocarbamate (dtc) ligand, named as MCM-41-dtc and this was characterized by X-ray diffraction, BET surface area, particle size analysis, ²⁹Si MAS NMR spectra and sulphur analysis. The sorption of mercury from 0.1M HCl solution by MCM-41-dtc was studied as a function of pH, [Hg²⁺], time and temperature. The sorption data obtained at various initial concentrations of mercury were fitted into Langmuir adsorption model. Mercury speciation in solution and the sorption capacity measurements indicated possible formation of a 1 : 1 square planar complex in the solid phase. A very rapid sorption of mercury was observed in the initial stages of equilibration, which can be attributed to the large surface area, wide porosity and fine particle size of MCM-41-dtc, facilitating facile accessibility of mercury into the inner pores of the sorbent. The enthalpy change accompanied by the sorption of mercury was found to decrease from 83.7 to 6.2 kJ/mol, when the initial concentration of mercury was increased from 5^.10^-4M to 1.5^.10^-3M.     

Book reviews

Inorganic mercury ions (Hg²⁺) in laboratory prepared solutions were determined with a screen-printed carbon electrode (SPCE) coated with a polyaniline-methylene blue (PANI-MB) polymer layer. The structure and properties of the PANI-MB polymer layer were compared to that of normal polyaniline (PANI) in order to elucidate the structure of the PANI-MB layer. The electrically-conducting polymers were prepared by electrochemical polymerisation of monomer solutions of aniline, and mixed solutions of aniline with methylene blue onto respective screen-printed carbon electrodes (SPCEs). Scanning Electron Microscopy (SEM) analyses of the SPCE polymer coated electrodes have shown that nanostructured materials have formed with the diameters of the PANI nanoclusters and PANI-MB nanorods at approximately 200 nm. Anodic stripping voltammetry (ASV) was used to evaluate a solution composed of 1 × 10^?6 M Hg²⁺, in the presence of the SPCE/PANI-MB polymer sensor electrode. The Hg²⁺ ions were determined as follows: (i) pre-concentration and reduction on the modified electrode surface and (ii) subsequent stripping from the electrode surface during the positive potential sweep. The experimental conditions optimised for Hg²⁺ determination included the supporting electrolyte concentration and the accumulation time. The results obtained have shown that the SPCE/PANI-MB polymer sensor electrode operates optimally at a pH 2, with the supporting electrolyte concentration at 0.5 M HCl. A linear calibration curve was found to be in the range of 1 × 10^?8 M to 1 × 10^?5 M Hg²⁺ after 120 s of pre-concentration. The detection limit was calculated and found to be 54.27 ± 3.28 µg L^?1 of Hg²⁺. The results have also shown that a conducting polymer modified SPCE sensor electrode can be used as an alternative transducer for the voltammetric stripping and analysis of inorganic Hg²⁺ ions.     

Novel methodology for the study of mercury methylation and reduction in sediments and water using <Superscript>197</Superscript>Hg radiotracer

Mercury tracers are powerful tools that can be used to study mercury transformations in environmental systems, particularly mercury methylation, demethylation and reduction in sediments and water. However, mercury transformation studies using tracers can be subject to error, especially when used to assess methylation potential. The organic mercury extracted can be as low as 0.01% of the endogenous labeled mercury, and artefacts and contamination present during methylmercury (MeHg) extraction processes can cause interference. Solvent extraction methods based on the use of either KBr/H₂SO₄ or HCl were evaluated in freshwater sediments using ¹⁹⁷Hg radiotracer. Values obtained for the ¹⁹⁷Hg tracer in the organic phase were up to 25-fold higher when HCl was used, which is due to the coextraction of ¹⁹⁷Hg²⁺ into the organic phase during MeHg extraction. Evaluations of the production of MeHg gave similar results with both MeHg extraction procedures, but due to the higher Hg²⁺ contamination of the controls, the uncertainty in the determination was higher when HCl was used. The Hg²⁺ contamination of controls in the HCl extraction method showed a nonlinear correlation with the humic acid content of sediment pore water. Therefore, use of the KBr/H₂SO₄ method is recommended, since it is free from these interferences. ¹⁹⁷Hg radiotracer (T _1/2 = 2.673 d) has a production rate that is about 50 times higher than that of ²⁰³Hg (T _1/2 = 46.595 d), the most frequently used mercury radiotracer. Hence it is possible to obtain a similar level of performance to ²⁰³Hg when it is used it in short-term experiments and produced by the irradiation of ¹⁹⁶Hg with thermal neutrons, using mercury targets with the natural isotopic composition. However, if the 0.15% natural abundance of the ¹⁹⁶Hg isotope is increased, the specific activity of the ¹⁹⁷Hg tracer can be significantly improved. In the present work, ¹⁹⁷Hg tracer was produced from mercury 51.58% enriched in the ¹⁹⁶Hg isotope, and a 340-fold increase in specific activity with respect to natural mercury targets was obtained. When this high specific activity tracer is employed, mercury methylation and reduction experiments with minimum mercury additions are feasible. Tracer recovery in methylation experiments (associated with Me¹⁹⁷Hg production from ¹⁹⁷Hg²⁺ spike, but also with Hg²⁺ contamination and Me¹⁹⁷Hg artefacts) with marine sediments was about 0.005% g⁻¹ WS (WS: wet sediment) after 20 h incubation with mercury additions of 0.05 ng g⁻¹ WS, which is far below natural mercury levels. In this case, the amount of Hg²⁺ reduced to Hg⁰ (expressed as the percent ¹⁹⁷Hg⁰ recovered with respect to the ¹⁹⁷Hg²⁺ added) varied from 0.13 to 1.6% g⁻¹ WS. Me¹⁹⁷Hg production from ¹⁹⁷Hg²⁺ spike after 20 h of incubation of freshwater sediment ranged from 0.02 to 0.13% g⁻¹ WS with mercury additions of 2.5 ng g⁻¹ WS, which is also far below natural levels. ¹⁹⁷Hg⁰ recoveries were low, 0.0058 ± 0.0013% g⁻¹ WS, but showed good reproducibility in five replicates. Me¹⁹⁷Hg production from ¹⁹⁷Hg²⁺ spiked in freshwater samples ranged from 0.1 to 0.3% over a period of three days with mercury additions of 10 ng L⁻¹. A detection limit of 0.05% for Me¹⁹⁷Hg production from ¹⁹⁷Hg²⁺ spike was obtained in seawater in a 25 h incubation experiment with mercury additions of 12 ng L⁻¹.     

Sampling and determination of gas phase divalent mercury in the air using a KCl coated denuder

KCl coated denuders were employed for the measurement of divalent mercury (Hg²⁺) species in the air. Laboratory tests show that gaseous Hg²⁺ can be collected by the denuder with an average efficiency of 98% and elemental Hg will pass through it freely. Hg²⁺ trapped in the denuder can be quantitatively extracted by 1 mol/L HCl and analyzed by the method of SnCl₂ reduction-CVAFS determination. Hg²⁺ concentrations of 0.04–0.15 ng m^–3 corresponding to about 2–9% of the total gaseous mercury in the ambient air were determined at several sampling locations.     

Sorption of elements from mineral acid solutions by alkylated dibenzocrown ethers

Sorption of various elements by alkylated dibenzocrown ethers (CE) from HCl and HNO₃ solutions was studied. The distribution coefficients of elements depend on the size of the macrocyclic ring of CE and the type and concentration of the acid. Di-tert-butyldibenzo-24-crown-8 possesses optimal properties upon sorption of Au, Ga, Fe, Mo, Sb, Sn, and Re from 5 M HCl. In these cases, the elements are selectively sorbed from mixtures of complex composition, which can be used to develop methods of recovery and separation of elements.     

CaCl2添加对热解煤中汞析出规律影响的实验研究

在程序升温热解反应装置上,研究了低氯煤中添加不同氯含量（质量分数0.1%、0.3%、0.5%）的CaCl₂对煤热解过程中汞析出规律的影响。实验结果表明,温度是影响汞析出的关键因素;随着氯添加量的增加,Hg²⁺析出比例呈上升趋势,且汞的最佳析出温度降低,汞的释放率也有所降低;随着热解气氛中O₂比例的增加,Hg²⁺比例也略有增加;较高的升温速率能加快汞的释放,也能提高Hg²⁺的比例。低氯煤中添加氯化钙能够强化单质汞的氧化。     

Robust microwave-assisted extraction protocol for determination of total mercury and methylmercury in fish tissues

A rapid and efficient closed vessel microwave-assisted extraction (MAE) method based on acidic leaching was developed and optimized for the extraction of total mercury (Hg), inorganic mercury (Hg²⁺) and methylmercury (CH₃Hg⁺) from fish tissues. The quantitative extraction of total Hg and mercury species from biological samples was achieved by using 5 mol L⁻¹ HCl and 0.25 mol L⁻¹ NaCl during 10 min at 60 °C. Total Hg content was determined using inductively coupled plasma mass spectrometry (ICP-MS). Mercury species were measured by liquid chromatography hyphenated with inductively coupled plasma mass spectrometry (LC-ICP-MS). The method was validated using biological certified reference materials ERM-CE464, DOLT-3, and NIST SRM-1946. The analytical results were in good agreement with the certified reference values of total Hg and CH₃Hg⁺ at a 95% confidence level. Further, accuracy validation using speciated isotope-dilution mass spectrometry (SIDMS, as described in the EPA Method 6800) was carried out. SIDMS was also applied to study and correct for unwanted species transformation reactions during and/or after sample preparation steps. For the studied reference materials, no statistically significant transformation between mercury species was observed during the extraction and determination procedures. The proposed method was successfully applied to fish tissues with good agreement between SIDMS results and external calibration (EC) results. Interspecies transformations in fish tissues were slightly higher than certified reference materials due to differences in matrix composition. Depending on the type of fish tissue, up to 10.24% of Hg²⁺ was methylated and up to 1.75% of CH₃Hg⁺ was demethylated to Hg²⁺.     

Determination of inorganic and total mercury by vapor generation atomic absorption spectrometry using different temperatures of the measurement cell

A simple and inexpensive laboratory-built flow injection vapor generation system coupled to atomic absorption spectrometry (FI-VG AAS) for inorganic and total mercury determination has been developed. It is based on the vapor generation of total mercury and a selective detection of Hg^2 + or total mercury by varying the temperature of the measurement cell. Only the inorganic mercury is measured when the quartz cell is at room temperature, and when the cell is heated to 650 °C or higher the total Hg concentration is measured. The organic Hg concentration in the sample is calculated from the difference between the total Hg and Hg^2 + concentrations. Parameters such as the type of acid (HCl or HNO₃) and its concentration, reductant (NaBH₄) concentration, carrier solution (HCl) flow rate, carrier gas flow rate, sample volume and quartz cell temperature, which influence FI-VG AAS system performance, were systematically investigated. The optimized conditions for Hg^2 + and total Hg determinations were: 1.0 mol l^− 1 HCl as carrier solution, carrier flow rate of 3.5 ml min^− 1, 0.1% (m/v) NaBH₄, reductant flow rate of 1.0 ml min^− 1 and carrier gas flow rate of 200 ml min^− 1. The relative standard deviation (RSD) is lower than 5.0% for a 1.0 μg l^− 1 Hg solution and the limit of quantification (LOQ, 10 s) is 55 ng g^− 1. Certified samples of dogfish muscle (DORM-1 and DORM-2) and non-certified fish samples were analyzed, using a 6.0 mol l^− 1 HCl solution for analyte extraction. The Hg^2 + and CH₃Hg⁺ concentrations found were in agreement with certified ones.     

Synthesis of polyacrylonitrile by single‐electron transfer‐living radical polymerization using Fe(0) as catalyst and its adsorption properties after modification

Fe(0) was firstly used as single‐electron transfer‐living radical polymerization catalyst for acrylonitrile polymerization using carbon tetrachloride as initiator, hexamethylenetetramine as N‐ligand, and N,N‐dimethylformamide as the solvent at 65 °C. First‐order kinetic studies indicated that this polymerization proceeded in a “living”/controlled manner. The living nature of the polymerization was also confirmed by chain extension of methyl methacrylate with polyacrylonitrile (PAN) as macroinitiator. Furthermore, PAN was modified with NH₂OH·HCl to generate amidoxime groups for extraction of heavy metal ions (Hg²⁺) from aqueous solutions. Fourier transformed infrared spectroscopy was performed to characterize chemical composition and structure. The adsorption property of Hg²⁺ was investigated at different pH values of aqueous solutions and distilled water. The maximal saturated adsorption capacity of Hg²⁺ was 4.8 mmol g^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Sampling and determination of gas phase divalent mercury in the air using a KCl coated denuder

KCl coated denuders were employed for the measurement of divalent mercury (Hg²⁺) species in the air. Laboratory tests show that gaseous Hg²⁺ can be collected by the denuder with an average efficiency of 98% and elemental Hg will pass through it freely. Hg²⁺ trapped in the denuder can be quantitatively extracted by 1 mol/L HCl and analyzed by the method of SnCl₂ reduction-CVAFS determination. Hg²⁺ concentrations of 0.04–0.15 ng m^–3 corresponding to about 2–9% of the total gaseous mercury in the ambient air were determined at several sampling locations. Received: 24 September 1996 / Revised: 14 January 1997 / Accepted: 18 January 1997     

Study of the gadolinium sorption on the C100 ion-exchange resin for the development of the antineutrino detector targets

Adsorption of the gadolinium from H₂O and HCl solutions on the ion-exchange resin C100 is investigated. The experiments were carried out by varying the acidity of the liquid phase, the amount of sorbent, and the temperature. The maximal sorption of the ions Gd³⁺ is observed from the solution 0–0.2 M HCl under optimal conditions, the sorption reaches more than 99.5%. Sorption of Gd³⁺ on C100 from H₂O solution occurs most intensively during the first 3 min then for 30 min the system smoothly comes to equilibrium. The maximal sorption capacity of the resin C100 amounted to 1.2 ± 0.1 mmol g^?1. The thermodynamic parameters of sorption: ΔG = ? 24.20 kJ mol^?1, ΔS = ? 90.27 J mol^?1 K^?1, ?H = ? 50.93 kJ mol^?1 were evaluated. It is shown that the sorption of gadolinium on the ion-exchange resin C100 is described by models of kinetically pseudo-first and pseudo-second order. It is established that the Gd³⁺ sorption on the C100 resin is reversible second order chemical reaction.     

Sorption of CO2, C2H4, N2O and their binary mixtures in poly(methyl methacrylate)

Sorption of carbon dioxide, ethylene, and nitrous oxide in poly(methyl methacrylate) (PMMA) at 35°C has been characterized for each gas as a pure component and for mixtures of carbon dioxide/ethylene and carbon dioxide/nitrous oxide. Pressures up to 20 atm were examined. Pure-component sorption isotherms are concave to the pressure axis for each of the gases. This behavior is accurately described by the dual-mode sorption model. Using only the purecomponent dual-mode parameters and the generalization of the model for gas mixtures, one can predict the total concentration of gas sorbed in the polymer to within an average deviation of ±2.01% for the CO₂/C₂H₄/PMMA system and ±0.98% for the CO₂/N₂O/PMMA system. In both systems, for each component of the mixture, sorption levels were lower than corresponding pure-component sorption levels at pressures equal to the partial pressure of the respective components in the mixture. Depression of the sorbed concentration in mixture situations appears to be a general feature of the above systems and can be substantial in some situations. For the CO₂/C₂H₄/PMMA system, use of pure-component sorption data to estimate the total sorbed concentration in the mixture would be in error by as much as 40% if one failed to account for competition phenomena responsible for depression in mixed-gas situations. Mixture pressures as high as 20 atm were studied for both systems and in the CO₂/N₂O/PMMA system sorbed concentrations reach 33.90 [cm³(STP)/cm³ polymer] without any significant deviation from model predictions.     

Uptake of inorganic Hg by organically modified silicates: influence of pH and chloride concentration on the binding pathways and electrochemical monitoring of the processes

Transport of mercury species in aquatic media is strongly affected by sorption processes on both organic and inorganic particles, and such mass transfer reactions are governed by speciation of this contaminant in the environment. The present research investigates the uptake of inorganic Hg^II species by sorbent materials based on polysiloxane-immobilized amine or thiol ligands, with the goal to highlight the effect of speciation on the sorption processes. Mercury binding was studied as a function of pH and chloride concentration to cover a wide range of species, including some among the most widely encountered forms in natural medium (HgCl₄²⁻, HgCl₃⁻, HgCl₂, Hg(OH)₂). It was found on the one hand that all these species are liable to be removed from solution by strong binding to silica gels grafted with mercaptopropyl groups. On the other hand, the use of silica bearing aminopropyl moieties has led to the selective accumulation of anionic chloro-complexes of Hg^II in acidic medium in the presence of high chloride concentration and to the uptake of Hg^II hydroxide around neutral pH, while HgCl₂ cannot be adsorbed on this material. The former reaction involves electrostatic interactions between HgCl₄²⁻ or HgCl₃⁻ and the ammonium form of polysiloxane-immobilized amine ligands, and the latter is driven by complexation of Hg^II species to the unprotonated amine groups. The interest of electrochemistry at carbon paste electrodes modified with these adsorbents for characterizing the sorption processes was also described by applying the following sequence “voltammetric detection subsequent to open-circuit accumulation”. This approach allows the in situ determination of the amount of mercury in the organic-inorganic hybrid phase, as a function of speciation in solution and without significant modification in the solution-phase concentrations, so that the adsorption and ion-exchange isotherms can be obtained very easily and without requiring additional treatment of the solid material.     

Effect of temperature on the sorption behavior of sodium potassium fluorophlogopite with respect to the heavy metal ions Cd<Superscript>2+</Superscript>, Hg<Superscript>2+</Superscript>, and Pb<Superscript>2+</Superscript>

The effect of temperature on the sorption behavior of a synthesized gel structurally close to the fluorine mica mineral, sodium potassium fluorophologopite, was studied for the heavy metal ions Cd²⁺, Hg²⁺, and Pb²⁺. The synthesized gel was characterized by X-ray powder pattern, energy dispersive spectrometry, infrared spectroscopy, and thermogravimetric analysis and was found to have the composition Na_0.5K_0.5Mg(AlSi₃O₁₀)F₂·6H₂O. The effect of temperature on sorption was studied with respect to varying concentrations of metal ions. The overall sorption capacity of the synthesized gel was found to depend on the number of ion active groups per unit weight of the material. The data were expressed in terms of distribution coefficients (K _d). Sorption data followed Freundlich adsorption isotherms. Studies showed that sorption decreased as the concentration of metal ions increased and increased as the temperature grew, which was evidence that the process was endothermic. The text was submitted by the authors in English.     

Observation of doubly charged mercury cluster ions Hg n 2+, n=1-10 using secondary ion mass spectrometry

Mass spectra of doubly charged mercury clusters (m/z=30-1065) were investigated by secondary ion mass spectrometry. Positively charged ions were generated from an amalgam of mercury and silver by bombardment with a xenon ion beam and mass analysis by a grand-scale sector type mass spectrometer. Hg _n ²⁺, n=1-10 and Hg _n +, n =1- 5 were observed. Some doubly charged mercury clusters, (Hg _n ²⁺) survived at least for 0.1 ms.     

Sorbents based on calix[4]arenes for extraction of technetium(vii) from acidic and alkaline media

Sorption of Tc^VII from solutions of various compositions with new sorbents prepared by the noncovalent immobilization of (thia)calix[4]arenes on the Amberlite XAD-7™ support was studied. The sorbents studied efficiently extract technetium(vii) from both acidic and alkaline media. The sorption capacity of the sorbent with thiacalix[4]arene groups is superior to that of the sorbents with calix[4]arene groups and several times higher than that of the sorbents previously proposed for the sorption of Tc^VII. Technetium(vii) is sorbed by this sorbent as 1: 1 and 1: 2 thiacalix[4]arene—NH₄TcO₄ and 1: 1 and 1: 2 thiacalix[4]arene—NaTcO₄ complexes.     

Selective detection of mercury(II) and methylmercury(II) via coordination-induced emission of a small-molecule probe

Mercury is one of the major toxic pollutants and has many adverse effects on human health. The main mercury species in the environment or in living organisms are inorganic mercuric ion (Hg²⁺) and organic methylmercury (CH3Hg+). Detection of the two mercury ions is a particularly active topic in the molecular sensing field during the past decade. However, efficient sensors that can sensitively detect and discriminate the two species are rare. In this work, we adopt the concept of restriction of intramolecular rotations which is the basis of aggregation induced emission, and design a molecular probe with pyridyl group as the chelating unit and 1,8-naphthalimide as the fluorescent unit for the detection of both Hg²⁺ and CH₃Hg⁺. When the probe is free in solution, it exhibits weak fluorescence because free intramolecular rotations of the 1,8-naphthalimide moieties non-radiatively annihilate its excited state. However, upon coordination with Hg²⁺ or CH₃Hg⁺, the rotation of 1,8-naphthalimide moieties would be restricted due to the chelation between 1,8-naphthalimide and Hg²⁺ or CH₃Hg⁺, leading to significantly enhanced fluorescent emission. The response induced by Hg²⁺ is much stronger than CH₃Hg⁺; but for specific detection of CH₃Hg⁺, we introduced a T-rich DNA fragment which could completely mask Hg²⁺ in solution. Furthermore, we have employed the sensor for confocal imaging of Hg²⁺ and CH₃Hg⁺in immobilized cells. We expect the probe design tactics can be generally useful for sensing many other analytes.