Conventional inner diameter short capillary columns: an approach to speeding up gas chromatographic analysis of medium complexity samples.

Short capillary columns (5 m) with 0.25 mm inner diameter (I.D.) are applied to the GC analysis of medium complexity samples (up to 30 components) with the aim of shortening analysis time. This approach is complementary to fast GC with narrow-bore columns and is based on compensating the lower efficiency of short columns with conventional I.D.'s (0.25-0.32 mm) by using a stationary phase selectivity suitable to separate the components of the sample under investigation, so that the required resolution power is achieved but, at the same time, the analysis time is shortened. The qualitative and quantitative effectiveness of this approach is demonstrated through the analysis of: essential oils with different compositions (chamomile and rosemary), low-volatility triterpenes in a plant extract (Maytenus aquifolium and M. ilicfolium), thermolabile pyrethrins in a Pyrethrum extract, and a mixture of pesticides applied to protect medicinal plant crops. In all examples, GC analysis was five to ten times faster than with conventional columns.     

Evaluation of low-pressure gas chromatography linked to ion-trap tandem mass spectrometry for the fast trace analysis of multiclass pesticide residues

A rapid multiresidue method for the analysis of 72 pesticides has been developed using a single injection with low-pressure gas chromatography/tandem mass spectrometry (LP-GC/MS/MS). The LP-GC/MS/MS method used a short capillary column of 10 m x 0.53 mm i.d. x 0.25 microm film thickness coupled with a 0.6 m x 0.10 mm i.d. restriction at the inlet end. Optimal LP-GC conditions were determined which achieved the fastest separation in MS/MS detection mode. Also MS/MS conditions were optimized in order to increase sensitivity and selectivity. The analytical parameters of the LP-GC/MS/MS method were compared with those obtained by GC/MS/MS using a conventional capillary column (30 m x 0.25 mm i.d. x 0.25 microm film thickness). Better precision and sensitivity values were obtained with the LP-GC/MS/MS approach. The limits of detection (LOD) of the compounds ranged from 0.1 to 14.1 microg L(-1) for LP-GC/MS/MS, lower than those obtained for conventional GC/MS/MS that ranged from 0.1 to 17.5 microg L(-1). The peak widths obtained with the short column in LP-GC are similar to those obtained using conventional capillary GC columns, and the peaks can be successfully identified by MS/MS detection with the conventional scan speed of ion-trap instruments. In addition, the analysis time was significantly reduced with LP-GC/MS/MS (32 min) versus GC/MS/MS (72 min), allowing the number of samples analyzed per day in a routine laboratory to be doubled.     

High-speed gas chromatography with direct resistively-heated column (ultra fast module-GC)-separation measure (S) and other chromatographic parameters under different analysis conditions for samples of different complexities and volatilities

The influence of GC speed on the separation capability of a chromatographic system is reported measuring a series of parameters including separation measure (S), peak capacity (n), peak width (w), analysis time, t(b) (determined on the last eluting compound) and separation measure/analysis time ratio (S/t(b)) determined by analyzing a bergamot essential oil sample and a standard mixture of pesticides. Conventional GC, fast GC (with 10 m (FGC10) and 5 m (FGC5) narrow-bore columns), and direct resistively-heated ultra fast module-GC (UFM-GC) were the GC speed approaches used. The influence of different heating rates with a constant flow for FGC5, FGC 10, and UFM-GC and with variable flows for UFM-GC on S, n, w, S/t(b), and t(b) was also studied. The results of this study show that: (a) separation capability of the chromatographic system (i.e. S and n) and analysis time depend on the GC approaches. Within each GC approach, S and n and analysis time depend on the heating rates, although to a different extent, and S and n decrease much less than the gain in analysis time, in particular when fast heating rates are applied; (b) in UFM-GC, the loss of separation capability with heating rate can also be partially compensated by the choice of an appropriate flow rate that, within each heating rate, may contribute to increase S while reducing t(b); (c) within a specific GC approach, the chromatographic system (column and stationary phase) and conditions (heating and flow rates) must be such to achieve a suitable S-value when two analytes must be separated with a given resolution in a minimum analysis time.     

Fast-GC-conventional quadrupole mass spectrometry in essential oil analysis

This study reports on the compatibility of a conventional quadrupole MS (qMS) as detector for Fast-GC in terms of separation, identification, and quantitation when applied to the analysis of peppermint essential oil (e.o.), adopted as representative of this field. The influence of Fast-GC carried out on a 10 mx0.1 mm id narrow bore column with temperature programmes from 20 to 60 degrees C/min on the results of a qMS in total ion chromatograms (TIC) at different speeds (from 999 and 11 111 amu/s) and SIM modes was evaluated on ten differently abundant components characterizing peppermint e.o. Separation measure (S), peak capacity (n), and half height peak width were taken as separation parameters; match quality, number of scans per peak (NP), spectral skewing, and TIC area repeatability were used for identification. Quantitation was in SIM mode and NP, dwell time, SIM area repeatability and calibration curves, LOD, and LOQ of the selected components were measured. The results show that the peppermint e.o. markers can successfully be analysed qualitatively and quantitatively by F-GC-qMS up to temperature programmes of 60 degrees /min provided that a suitable scan speed is applied. Fast-GC-qMS reduces analysis time by a factor greater than ten and gives results that are qualitatively reliable and quantitatively comparable to those obtained by conventional GC-qMS.     

Application of Comprehensive Two‐Dimensional Gas Chromatography (GC×GC) to the Qualitative Analysis of Essential Oils

This paper investigates the separation of moderately complex samples by comprehensive two‐dimensional gas chromatography (GC×GC). The analysis of peppermint (Mentha piperita) and spearmint (Mentha spicata) essential oil components, including acetates, alcohols, furans, ketones, sesquiterpenes, and terpenes, was achieved by one‐dimensional gas chromatography with quadrupole mass spectrometry detection (GC/MSD) and GC×GC with flame ionization detection. Peppermint essential oil was found to contain 89 identifiable peaks by GC×GC compared to 30 peaks in the GC/MSD chromatogram. Likewise, 68 peaks were found in the GC×GC chromatogram of spearmint (compared to 28 in GC/MSD). Plots of the first dimension versus second dimension retention times provided a fingerprint of the two essential oils, which revealed 52 similar compounds between the two essential oils as opposed to 18 matches by 1D GC.     

In Process Citation

To increase the analytical potential of the combination of gas chromatography and Fourier-transform infrared spectrometry, we have adapted our system to use of capillary columns, and automated the acquisition and treatment of the data. The performance of the method was tested by analysis of complex mixtures such as the essential oils of peppermint and lavender. The sensitivity and resolution are poorer than those obtained with classical GC detectors but the spectra are very useful for determining molecular structure.     

Fast GC for the analysis of citrus oils

In this investigation, the gas chromatographic (GC) analysis of citrus essential oils is carried out in 3.3 min, with a speed gain of almost 14 times in comparison with traditional GC procedures. The fast method that is developed requires the application of severe experimental conditions (accelerated temperature program rates, high inlet pressures, and split ratios) and, thus, the support of adequate instrumentation. The samples investigated can be considered to be rather complex and, although a slight loss in peak resolution is observed, the overall analytical result is excellent. All data obtained are compared with that of a conventional application on the same matrices. This is done in order to evaluate the effectiveness and advantages of fast GC achieved with narrow bore columns.     

Comprehensive two-dimensional gas chromatography in the analysis of volatile samples of natural origin: a multidisciplinary approach to evaluate the influence of second dimension column coated with mixed stationary phases on system orthogonality

The study evaluates the influence of selectivity tuning of the stationary phase of the second dimension on the orthogonality of a comprehensive two-dimensional gas chromatography (GC x GC) system. Two different sets of columns, providing independent and semi-independent separation mechanisms were used. The first consisted of a first dimension separating analytes on a volatility basis (i.e. a non-polar polydimethylsiloxane (OV1) column) combined with a second dimension separating by polarity, using columns coated with 100% polyethylene glycol (CW20M), CW20M/OV1 mixtures in ratios of 25-75%, and polydimethylsiloxane, 7% phenyl, 7% cyanopropyl (OV1701). The second set consisted of a first dimension separating analytes on a polarity basis (100% CW20M column) combined with a second dimension separating by volatility, consisting of columns coated with 100% OV1, OV1/CW20M mixtures in ratios of 25-75%, and 100% OV1701. Medium-complexity mixtures of natural origin (i.e. peppermint essential oil and a standard mixture of suspected allergens) consisting of components in a relatively limited range of molecular weights (MW) and volatilities, but belonging to different classes of compounds in a wide range of polarity (mono- and sesquiterpenoids, hydrocarbons and oxygenated compounds) were analysed with the above sets of columns. Different approaches were used to evaluate peak spreading on the GC x GC separation plane and degree of orthogonality of the column sets, namely: (1) a Factor Analysis (FA) approach, estimating the correlation coefficients and spreading angles of the sample components in the two-dimensional chromatographic plane; (2) an Informational Theory (IT) approach, based on determining a group of parameters including: informational entropy, % synentropy and similarity (H); and (3) an approach based on estimating the amount of separation space used, i.e. a practical parameter that directly refers to the experimental separation plane of the GC x GC chromatogram. Results showed that peak spreading in the chromatographic plane, when CW20M and OV1 are combined in different ratios, can be predicted from retention mechanisms, and that the degree of orthogonality measured with different approaches, is consistent with the divergent nature, in terms of polarity of the stationary phases combined in the GC x GC system.     

Conventional and narrow bore short capillary columns with cyclodextrin derivatives as chiral selectors to speed-up enantioselective gas chromatography and enantioselective gas chromatography-mass spectrometry analyses

The analysis of complex real-world samples of vegetable origin requires rapid and accurate routine methods, enabling laboratories to increase sample throughput and productivity while reducing analysis costs. This study examines shortening enantioselective-GC (ES-GC) analysis time following the approaches used in fast GC. ES-GC separations are due to a weak enantiomer-CD host-guest interaction and the separation is thermodynamically driven and strongly influenced by temperature. As a consequence, fast temperature rates can interfere with enantiomeric discrimination; thus the use of short and/or narrow bore columns is a possible approach to speeding-up ES-GC analyses. The performance of ES-GC with a conventional inner diameter (I.D.) column (25 m length x 0.25 mm I.D., 0.15 microm and 0.25 microm d(f)) coated with 30% of 2,3-di-O-ethyl-6-O-tert-butyldimethylsilyl-beta-cyclodextrin in PS-086 is compared to those of conventional I.D. short column (5m length x 0.25 mm I.D., 0.15 microm d(f)) and of different length narrow bore columns (1, 2, 5 and 10 m long x 0.10 mm I.D., 0.10 microm d(f)) in analysing racemate standards of pesticides and in the flavour and fragrance field and real-world-samples. Short conventional I.D. columns gave shorter analysis time and comparable or lower resolutions with the racemate standards, depending mainly on analyte volatility. Narrow-bore columns were tested under different analysis conditions; they provided shorter analysis time and resolutions comparable to those of conventional I.D. ES columns. The narrow-bore columns offering the most effective compromise between separation efficiency and analysis time are the 5 and 2m columns; in combination with mass spectrometry as detector, applied to lavender and bergamot essential oil analyses, these reduced analysis time by a factor of at least three while separation of chiral markers remained unaltered.     

High-speed analyses using rapid resolution liquid chromatography on 1.8-microm porous particles

The potential of high-speed analyses by rapid resolution liquid chromatography (RRLC) and RRLC/MS on 1.8-microm porous particles packed into short columns operated at high flow-rate was investigated and compared with the performance of 5-microm porous particles packed into conventional columns. Using similar chemistries, the ease of conversion from conventional HPLC to an RRLC method was demonstrated. In order to display the practicality of RRLC separations, the analysis of pesticides in crops and catechins in Japanese green tea was selected. Using the Japanese Food Hygiene Law method, which employs a conventional 5-microm RP column (250 mm x 4.6 mm) for quantification of pesticides in crops, the analysis time was 25 min under isocratic conditions. Using the RRLC method on the short (50 mm x 4.6 mm) column packed with 1.8-microm porous particles, the same separation could be performed in 0.8 min with the RRLC/MS method without a loss in resolution. At the highest flow rate, compared to the conventional method, the time could be reduced by a factor of 31. In gradient elution, the fastest separation of catechins in Japanese green tea was achieved by RRLC on 50-mm x 4.6-mm id or 50-mm x 2.1-mm id RRLC columns packed with 1.8-microm particles. The analysis time at 5 mL/min was less than 1 min. Compared to the conventional HPLC method on a 150-mm column packed with 5-microm particles, time was reduced by a factor of 15. The effect of other experimental parameters such as the column temperature, acquisition rate of the detector and the influence of cell volume on chromatographic performance was also investigated. After the optimization, the analysis precision under the fastest RRLC conditions was examined. RSDs of retention time and peak area were 0.2% and 0.47%, respectively.     

Fast Temperature Programming in Gas Chromatography using Resistive Heating

The features of a resistive-heated capillary column for fast temperature-programmed gas chromatography (GC) have been evaluated. Experiments were carried out using a commercial available EZ Flash GC, an assembly which can be used to upgrade existing gas chromatographs. The capillary column is placed inside a metal tube which can be heated, and cooled, much more rapidly than any conventional GC oven. The EZ Flash assembly can generate temperature ramps up to 1200°/min and can be cooled down from 300 to 50°C in 30 s. Samples were injected via a conventional split/splitless injector and transferred to the GC column. The combination of a short column (5 m×0.25 mm i. d.), a high gas flow rate (up to 10 mL/min), and fast temperature programmes typically decreased analysis times from 30 min to about 2.5 min. Both the split and splitless injection mode could be used. With n-alkanes as test analytes, the standard deviations of the retention times with respect to the peak width were less than 15% (n = 7). First results on RSDs of peak areas of less than 3% for all but one n-alkane indicate that the technique can also be used for quantification. The combined use of a short GC column and fast temperature gradients does cause some loss of separation efficiency, but the approach is ideally suited for fast screening as illustrated for polycyclic aromatic hydrocarbons, organophosphorus pesticides, and triazine herbicides as test compounds. Total analysis times – which included injection, separation, and equilibration to initial conditions – were typically less than 3 min.     

Fast gas chromatography characterisation of purified semiochemicals from essential oils of Matricaria chamomilla L. (Asteraceae) and Nepeta cataria L. (Lamiaceae)

The chemical composition of Matricaria chamomilla L. and Nepeta cataria L. essential oils was determined by GC-MS on an apolar stationary phase by comparison of the characteristic fragmentation patterns with those of the Wiley 275L database. The GC-MS chromatograms were compared with those obtained by fast GC equipped with a direct resistively heated column (Ultra Fast Module 5% phenyl, 5 mx 0.1 mm, 0.1 microm film thickness). Analytical conditions were optimised to reach a good peak resolution (split ratio=1:100), with analysis time lower than 5 min versus 35-45 min required by conventional GC-MS. The fast chromatographic method was completely validated for the analysis of mono- and sesquiterpene compounds. Essential oils were then fractionated by column chromatography packed with silica gel. Three main fractions with high degree of purity in E-beta-farnesene were isolated from the oil of M. chamomilla. One fraction enriched in (Z,E)-nepetalactone and one enriched in beta-caryophyllene were obtained from the oil of N. cataria. These semiochemical compounds could act as attractants of aphid's predators and parasitoids.     

Enhanced resolution of Mentha piperita volatile fraction using a novel medium‐polarity ionic liquid gas chromatography stationary phase

The evaluation of a novel medium‐polarity ionic‐liquid‐based gas chromatography column, SLB‐IL60, towards the analysis of a complex essential oil, namely, a peppermint essential oil sample, is reported. The SLB‐IL60 30 m column was subjected to bleeding measurements, by means of conventional gas chromatography with mass spectrometry. The SLB‐IL60 column was then evaluated in the analysis of pure standard compounds, chosen as typical constituents of peppermint essential oil. Resolution and peak symmetry (expressed as tailing factors at 10% of peak height) were measured and the results were compared to those obtained on the most widely used columns in such an application, namely a medium‐polarity [100% poly(ethyleneglycol)] stationary phase, and an apolar 5% diphenyl/95% dimethyl siloxane. The final part of the evaluation was dedicated to the gas chromatography with mass spectrometry analysis of a peppermint essential oil sample and again the data were compared to those obtained on the 100% poly(ethyleneglycol) and the 5% diphenyl/95% dimethyl siloxane phase. Linear retention indices were determined for all the identified components on the ionic liquid capillary.     

Improvement of the liquid-chromatographic analysis of protein tryptic digests by the use of long-capillary monolithic columns with UV and MS detection

Optimisation of peak capacity is an important strategy in gradient liquid chromatography (LC). This can be achieved by using either long columns or columns packed with small particles. Monolithic columns allow the use of long columns at relatively low back-pressure. The gain in peak capacity using long columns was evaluated by the separation of a tryptic bovine serum albumin digest with an LC–UV–mass spectrometry (MS) system and monolithic columns of different length (150 and 750 mm). Peak capacities were determined from UV chromatograms and MS/MS data were used for Mascot database searching. Analyses with a similar gradient slope for the two columns produced ratios of the peak capacities that were close to the expected value of the square root of the column length ratio. Peak capacities of the short column were 12.6 and 25.0 with 3 and 15 min gradients, respectively, and 29.7 and 41.0 for the long column with 15 and 75 min gradients, respectively. Protein identification scores were also higher for the long column, 641 and 750 for the 3- and 15-min gradients with the short column and 1,376 and 993 for the 15- and 75-min gradients with the long column. Thus, the use of long monolithic columns provides improved peptide separation and increased reliability of protein identification.     

High temperature liquid chromatography of intact proteins using organic polymer monoliths and alternative solvent systems

Alternative approaches to conventional acetonitrile gradient methods for reversed-phase liquid chromatographic analysis of intact proteins have been investigated using commercial poly(styrene-co-divinylbenzene) monolithic columns (Dionex ProSwift™ RP-2H and RP-4H). Alternative solvents to acetonitrile (2-propanol and methanol) coupled with elevated temperatures demonstrated complementary approaches to adjusting separation selectivity and reducing organic solvent consumption. Measurements of peak area at increasing isothermal temperature intervals indicated that only minor (<5%) decreases in detectable protein recovery occurred between 40 and 100 °C on the timescale of separation (2–5 min). The reduced viscosity of a 2-propanol/water eluent at elevated temperatures permitted coupling of three columns to increase peak production (peaks/min) by 16.5%. Finally, narrow-bore (1 mm i.d.) columns were found to provide a more suitable avenue to fast, high temperature (up to 140 °C) separations.     

Adulteration of Essential Oils: A Multitask Issue for Quality Control. Three Case Studies: Lavandula angustifolia Mill., Citrus limon (L.) Osbeck and Melaleuca alternifolia (Maiden & Betche) Cheel

The quality control of essential oils (EO) principally aims at revealing the presence of adulterations and at quantifying compounds that are limited by law by evaluating EO chemical compositions, usually in terms of the normalised relative abundance of selected markers, for comparison to reference values reported in pharmacopoeias and/or international norms. Common adulterations of EO consist of the addition of cheaper EO or synthetic materials. This adulteration can be detected by calculating the percent normalised areas of selected markers or the enantiomeric composition of chiral components. The dilution of the EO with vegetable oils is another type of adulteration. This adulteration is quite devious, as it modifies neither the qualitative composition of the resulting EO nor the marker’s normalised percentage abundance, which is no longer diagnostic, and an absolute quantitative analysis is required. This study aims at verifying the application of the two above approaches (i.e., normalised relative abundance and absolute quantitation) to detect EO adulterations, with examples involving selected commercial EO (lavender, bergamot and tea tree) adulterated with synthetic components, EO of different origin and lower economical values and heavy vegetable oils. The results show that absolute quantitation is necessary to highlight adulteration with heavy vegetable oils, providing that a reference quantitative profile is available.     

The novel use of gas chromatography-ion mobility-time of flight mass spectrometry with secondary electrospray ionization for complex mixture analysis

Increasing the dimensionality of an analysis enables more detailed and comprehensive investigations of complex mixtures. One dimensional separation techniques like gas chromatography (GC) and ion mobility spectrometry (IMS) provide limited chemical information about complex mixtures. The combination of GC, ion mobility spectrometry, and time-of-flight mass spectrometry (GC-IM-TOFMS) provides three-dimensional separation of complex mixtures. In this work, a hybrid GC-IM-TOFMS with a secondary electrospray ionization (SESI) source provided four types of analytical information: GC retention time, ion mobility drift time, mass-to-charge ratios, and ion intensity. The use of secondary electrospray ionization enables efficient and soft ionization of gaseous sample vapors at atmospheric pressure. Several complex mixtures, including lavender and peppermint essential oils, were analyzed by GC-SESI-IM-TOFMS. The resulting 3D data from these mixtures, each containing greater than 50 components, were plotted as 3D projections. In particular, post-processed data plotted in three dimensions showed that many mass selected GC peaks were resolved into different ion mobility peaks. This technique shows clear promise for further in-depth analyses of complex chemical and biological mixtures.     

气相色谱-质谱联用分析花椒挥发油的成分

 采用气相色谱 质谱联用技术对陕西富平产花椒挥发油的成分进行了分析 ,分离出了 17个峰 ,鉴定出了相对峰面积大于 1 0 %的组分共 16个 ,用峰面积归一化法定量测定了已确定组分的相对含量 ,其占挥发油总质量的95 %以上。     

Using comprehensive two-dimensional gas chromatography for the analysis of oxygenates in middle distillates I. Determination of the nature of biodiesels blend in diesel fuel

In the current energetic context (increasing consumption of vehicle fuels, greenhouse gas emission etc.) government policies lead to mandatory introduction in fossil fuels of fuels resulting from renewable sources of energy such as biomass. Blending of fatty acid alkyl esters from vegetable oils (also known as biodiesel) with conventional diesel fuel is one of the solutions technologically available; B5 blends (up to 5%w/w esters in fossil fuel) are marketed over Europe. Therefore, for quality control as well as for forensic reasons, it is of major importance to monitor the biodiesel origin (i.e. the fatty acid ester distribution) and its content when it is blend with petroleum diesel. This paper reports a comprehensive two-dimensional gas chromatography (GC x GC) method that was developed for the individual quantitation of fatty acid esters in middle distillates matrices. Several first and the second dimension columns have been investigated and their performances to achieve (i) a group type separation of hydrocarbons and (ii) individual identification and quantitation of fatty acid ester blend with diesel are reported and discussed. Finally, comparison of quantitative GC x GC results with reference methods demonstrates the benefits of GC x GC approach which enables fast and reliable individual quantitation of fatty acid esters in one single run. Results show that under developed chromatographic conditions, quantitative group type analysis of hydrocarbons is also possible, meaning that simultaneous quantification of hydrocarbons and fatty acid esters can be achieved in one single run.     

Quality evaluation of Semen Cassiae (Cassia obtusifolia L.) by using ultra-high performance liquid chromatography coupled with mass spectrometry

A sensitive and reliable ultra-high performance liquid chromatography-electrospray ionization-tandem mass spectrometry has been developed and partially validated to evaluate the quality of Semen Cassiae (Cassia obtusifolia L.) through simultaneous determination of 11 anthraquinones and two naphtha-γ-pyrone compounds. The analysis was achieved on a Poroshell 120 EC-C(18) column (100 mm × 2.1 mm, 2.7 μm; Agilent, Palo Alto, CA, USA) with gradient elution using a mobile phase that consisted of acetonitrile-water (30 mM ammonium acetate) at a flow rate of 0.4 mL/min. For quantitative analysis, all calibration curves showed perfect linear regression (r(2) > 0.99) within the testing range. This method was also validated with respect to precision and accuracy, and was successfully applied to quantify the 13 components in nine batches of Semen Cassiae samples from different areas. The performance of developed method was compared with that of conventional high-performance liquid chromatography method. The significant advantages of the former include high-speed chromatographic separation, four times faster than high-performance liquid chromatography with conventional columns, and great enhancement in sensitivity. This developed method provided a new basis for overall assessment on quality of Semen Cassiae.