Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

Hydrogen production by aqueous phase reforming of sorbitol using bimetallic Ni–Pt catalysts: metal support interaction

Hydrogen was produced by Aqueous Phase Reforming (APR) of 10% (w/w) sorbitol using mono- and bi-metallic catalysts of Ni and Pt supported on alumina nano-fibre (Alnf), mesoporous ZrO₂ and mixed oxides of ceria–zirconia–silica (CZxS) with varying concentration of silica (where x is silica concentration). X-ray diffraction, TEM/EDS and temperature programmed reduction were also carried on these catalysts to study the surface properties. It was observed that co-impregnation of Pt and Ni in atomic ratio 1:12 increased the reducibility of Ni by forming an alloy. However, sequential impregnation of Ni followed by Pt does not form the bi-metallic particles to increase the Ni reducibility. Reduction peak of co-impregnated Ni–Pt/Alnf was found to be 270 °C lower than the sequentially impregnated Pt/Ni/Alnf. The presence of silica at high concentration in CZxS support decreased the reducibility of ceria by forming an amorphous layer on Ce_xZr_1?xO₂ crystals, which also decreased Ni reducibility. The rate of H₂ formation from aqueous phase sorbitol reforming was found to be highest for co-impregnated Ni–Pt catalysts followed by sequentially impregnated Pt/Ni and monometallic Ni catalyst. The H₂ activity decreased in the following order of the supports: Alnf > ZrO₂ > CZ3S > CZ7S.     

Pt的氧化状态对甲醇氧化活性的影响

采用NaBH4还原法制备了XC-72碳黑负载的Pt电催化剂,并在化学还原后用H2O2处理部分催化剂以改变Pt的氧化状态,以期改善Pt活性中心上水的离解而提高催化活性.X射线光电子能谱结果表明,经H2O2处理的催化剂含有较多的氧化态Pt.通过循环伏安法和记时电流法考察了经处理和未经处理的催化剂在酸性条件下的甲醇氧化的催化...     

Transformation of n-hexane on Al2O3and SiO2supported Pt, Pt+Ga and Ir+Pt+Ga catalysts prepared by anchoring methods

Summary Transformation of n-hexane over Al₂O₃and SiO₂supported Pt, Pt+Ga and Ir+Pt+Ga catalysts was studied in a continuous-flow reactor operated under slug-pulse mode at 520°C. Bimetallic catalysts were prepared by introducing first Ga(OEt)₃and then diallylplatinum as precursor compounds. Iridium was then introduced viadecomposition of Ir₄(CO)₁₂adsorbed onto Pt+Ga catalysts. The addition of Ga to Pt/SiO₂catalyst decreased hydrogenation, aromatization and hydrogenolysis selectivity. Over Pt/Al₂O₃catalyst Ga increased hydrogenolysis selectivity and decreased isomerization and C₅-cyclization. The main effect of Ir was to increase hydrogenolysis selectivity and the stability of catalysts.</o:p>     

Selective hydroisomerization of n-dodecane over platinum supported on zeolites

In this study, in order to develop catalysts for the selective isomerization of higher paraffin, the hydroisomerization reaction of n-dodecane was performed as a model reaction. Pt/ZSM-48, Pt/HZSM-5, Pt/HY, and Pt/SAPO-11 were examined for the selective hydroisomerization of n-dodecane. The catalysts were characterized via X-ray powder diffraction, N₂ adsorption, and the temperature-programmed desorption of ammonia. Among the catalysts studied, the Pt/HZSM-48 catalyst exhibited the best isomerization selectivity in the hydroisomerization reaction of n-dodecane, which is attributed to the moderate acid sites and medium-sized pores present in the HZSM-48. The highest iso-dodecane yield was obtained at a reaction temperature of 280 °C in the Pt/HZSM-48 catalyst. The optimal selectivity of the n-dodecane hydroisomerization over the Pt/SAPO-11 catalyst was obtained at approximately 300 °C, which was slightly higher than that of the Pt/HZSM-48 catalyst.     

Property and structure of various platinum catalysts for low-temperature carbon monoxide oxidations

The oxidation of carbon monoxide (CO) has received more attention in the last two to three decades owing to its importance in different fields. To control this CO pollution, catalytic converters have been investigated. Different types of catalysts have been used in a catalytic converter for CO emission control purposes. Platinum (Pt)-based noble metal catalysts show great potential for CO oxidation in catalytic converters with high thermal stability and tailoring flexibility. Pt metal catalysts modified with promoters such as alkali metals and reducible metal oxides have received great attention for their superior catalytic activities in CO oxidation. Temperature, close environment of the catalyst, and chemical composition in the surface layer of the catalyst have a huge effect on the active phase dispersion and O₂ adsorption capacity of the Pt metal catalysts. The main difference in activities of Pt metal catalyst for CO oxidation in O₂ or H₂ atmosphere has found. The addition of supports in Pt metal catalysts has improved their performances and reduced their cost. These improvement strongly depends on the surface structure, morphology, number of active sites, and various Pt-O interactions. Many research articles have already been published in CO oxidation over Pt metal catalysts, but no review article dedicated to CO oxidation is available in the literature.     

Effective conversion of cellobiose and glucose to sorbitol using non-noble bimetallic NiCo/HZSM-5 catalyst

The tandem hydrolysis and hydrogenation of saccharides into sorbitol is an especially attractive reaction in the conversion of biomass. Here, an economical and efficient bimetallic catalyst for the transformation of glucose and cellobiose into sorbitol is reported. Non-precious metal based catalysts such as NiCo, Ni, and Co, were prepared via modified impregnation method, and NiCo/HZSM-5 showed superior performance for the synthesis of sorbitol (86.9% from cellobiose, 98.6% from D-glucose). Various characterizations, such as Brunner-Emmet-Teler (BET), X-ray diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS), confirmed that NiCo alloy formed and highly dispersed in NiCo/HZSM-5 catalyst. The high performance of fabricated catalyst would be attributed to the formation of nickel-cobalt alloy over HZSM-5 zeolite surface. High temperature and H₂ pressure were favorable for the tandem hydrolysis and hydrogenation reaction. Besides, the reaction pathway was also proposed based on the kinetics study. Cellobitol was detected as the intermediate in the reaction mixture. Furthermore, in the catalytic stability study, it was found that active metal species of NiCo/HZSM-5 were stable. The deactivation of catalyst would be due to the covering of acidic sites over NiCo/HZSM-5.     

A study of methane activation by modified gallium- and zinc-based catalysts

The activation of CH₄ has been probed by studying CH₄ oxidation at ambient pressure over gallium- and zinc-based catalysts prepared by precipitation and modified with Au and Pt. The unmodified gallium- and zinc-based catalysts were both active for CH₄ oxidation. Modification of these catalysts by the addition of Au and Pt, alone and in combination significantly increased the rate of CH₄ oxidation. The 1% Pt/Ga₂O₃ catalyst was the most active of the gallium-based systems. The addition of Au to ZnO markedly increased the activity compared with unmodified ZnO, whilst for Au in combination with Pt the activity was further enhanced due to a synergistic effect of the metals.     

钙钛矿型氧化物负载纳米金属催化剂结构的动态调变及其催化氧化CO反应性能

研究了钛酸钡和钛酸钙担载的Ag和Pt纳米催化剂的表面结构随氧化-还原处理过程的动态变化及其对CO完全氧化反应性能的影响.发现氧化物担载的Ag催化剂在氧化处理后其催化活性较还原处理的高; X射线衍射(XRD)和X射线光电子能谱(XPS)表征结果表明,氧化处理能够提高载体表面Ag颗粒的分散度,而还原处理导致Ag颗粒的聚集,从而降低了催化氧化CO反应的活性.氧化-还原处理改变了担载Ag纳米粒子的尺寸并影响其CO氧化反应活性.与此相反,氧化物担载的Pt催化剂在还原处理后所表现出的CO氧化反应活性较氧化处理的高; 对比研究发现,氧化和还原处理后Pt纳米粒子的尺寸基本相同,但是氧化处理的样品中Pt表面物种以氧化态为主,而还原处理后Pt表面物种主要为金属态.Pt纳米粒子表面化学状态随氧化-还原处理的调变是导致表面催化活性差异的主要原因.     

Pt/MOx(M=Ni,Fe,Co,Ce)催化剂上CO氧化反应中抗H2O与CO2的性能研究

我们研究了4种负载型Pt催化剂（1Pt/NiO、1Pt/FeO_x、1Pt/Co₃O₄和Pt/CeO₂）上不同反应条件下CO氧化活性及抗H₂O和CO₂性能.发现反应气氛中CO₂的加入与CO形成了竞争吸附,并在催化剂表面形成了碳酸盐物种堵塞了活性位,从而导致催化剂失活.反应气氛中H₂O的加入对1Pt/CeO₂催化剂的活性有所抑制,但对1Pt/FeO_x、1Pt/NiO和1Pt/Co₃O₄催化剂的活性却有促进作用.在1Pt/FeO_x和1Pt/CeO₂催化剂上的分步反应实验和动力学研究表明,尽管H₂O的加入在两种催化剂上均与CO形成了竞争吸附,但在1Pt/FeO_x催化剂上H₂O在载体表面解离形成的羟基更易与CO反应,开辟了新的反应途径,从而提高了反应性能.此外,H₂O的加入能有效分解该催化剂上的碳酸盐物种,从而保持了其稳定性.     

One-step synthesis of carbon-supported Pd–Pt alloy electrocatalysts for methanol tolerant oxygen reduction

A facile, one-step reduction route was developed to synthesize Pd-rich carbon-supported Pd–Pt alloy electrocatalysts of different Pd/Pt atomic ratios. As-prepared Pd–Pt/C catalysts exhibit a single phase fcc structure and an expansion lattice parameter. Comparison of the oxygen reduction reaction (ORR) on the Pd–Pt/C alloy catalysts indicates that the Pd₃Pt₁/C bimetallic catalyst exhibits the highest ORR activity among all the Pd–Pt alloy catalysts and shows a comparative ORR activity with the commercial Pt/C catalyst. Moreover, all the Pd–Pt alloy catalysts exhibited much higher methanol tolerance during the ORR than the commercial Pt/C catalyst. High methanol tolerance of the Pd–Pt alloy catalysts could be attributed to the weak adsorption of methanol induced by the composition effect, to the presence of Pd atoms and to the formation of Pd-based alloys.     

Nb-TiO2 supported Pt cathode catalyst for polymer electrolyte membrane fuel cells

The Nb-doped TiO₂ nanostructure (Nb-TiO₂) was prepared as a support of metal catalyst in polymer electrolyte membrane fuel cells. Using the Nb-TiO₂ nanostructure support, we prepared the Nb-TiO₂ supported catalyst. The Nb-TiO₂ supported Pt catalyst (Pt/Nb-TiO₂) showed the well dispersion of Pt catalysts (∼3 nm) on the Nb-TiO₂ nanostructure supports (∼10 nm). The Pt/Nb-TiO₂ showed an excellent catalytic activity for oxygen reduction compared with carbon supported Pt cathode catalyst. The enhanced catalytic activity of Pt/Nb-TiO₂ in electrochemical half cell measurement may be mainly due to well dispersion of Pt nanoparticles on Nb-TiO₂ nanosized supports. In addition, from XANES spectra of Pt L edge obtained with the supported catalysts, the improved catalytic activity of Pt/Nb-TiO₂ for oxygen reduction may be caused by an interaction between oxide support and metal catalyst.     

Hydrogenation of Benzonitrile on Sn-Pt/SiO2 Catalysts Prepared by Introducing SnEt4 to Pt/SiO2: Role of Tin

Liquid phase hydrogenation of benzonitrile was studied over Sn-Pt/SiO₂ catalysts prepared by introducing tetraethyl tin onto the 3 wt.% Pt/SiO₂ catalyst. Tin content of the catalysts ranged from 0.05 to 0.63 wt.%, whereas Sn/Pt surface atomic ratios determined by chemisorption measurements were between 0.1 to 3.5. Dibenzylamine selectivity influenced to a small extent by the level of conversion and the Sn/Pt ratio wasca. 75 %. The addition of tin to Pt in the range of (Sn/Pt)_surface = 0.50–1.25 led to an increase in the turnover frequency (TOF) by a factor of 2. TOF showed a maximum at a surface atomic ratio of Sn/Pt = 1. The enhancement of catalyst activity upon the addition of tin is explained by the formation of Sn⁺-Pt ensemble sites on the surface of bimetallic nanoclusters. It is suggested that highly dispersed positively charged tin species, by polarizing the triple bond, enhance the reactivity of the -CN group. Calcination at 300°C followed by re-reduction of the catalysts resulted in a monotonic decrease of specific activity with increasing Sn/Pt ratio.     

Sorbitol Hydrogenolysis to Glycols over Baisic Additive Promoted Ni-based Catalysts

A series of Ni based catalysts with different supports and basic additives were prepared by sequential impregnation method. The catalysts were characterized by XRD, BET, H₂-TPR and CO₂-TPD techniques. It was found that the introduction of basic additives enhanced the basicities of catalyats and promoted the dispersities of Ni particles by strong interaction between Ni²⁺ and basic additives. Among the Ni based catalysts, 10%Ni/10%La₂O₃/ZrO₂ showed the superior performance in sorbitol hydrogenolysis. The synergistic effect of Ni and La₂O₃ was proven to play an essential role in selective synthesis of EG and 1,2-PG. In the optimal reaction condition, the catalyst presented 100% sorbitol conversion and over 48% glycols (EG and 1,2-PG) yield. The kinetics study of polyols (sorbitol, xylitol and glycerol) hydrogenolysis showed that polyols with more hydroxyl number have higher activity and products distribution was final results of kinetic balance, which could give us some inspiration about how to change the products selectivity.     

Effect of the Electric Conductivity of a Catalyst on Methane Activation in a Dielectric Barrier Discharge Reactor

The influence of catalyst electric conductivity on methane activation in a planar-type dielectric barrier discharge reactor is investigated by empirically comparing the degree of methane conversion of bare Al₂O₃ with that of Pt/Al₂O₃; from this, it is determined that the latter catalyst converts less methane owing to the presence of Pt. Calculations and comparisons of electric fields with and without Pt show that the presence of a Pt catalyst results in a lower electric field than does bare Al₂O₃. An analysis of product gases based on the correlation between the fragmentation of radicals and the electric field also indicates that the electric field is decreased by using Pt. From these results, it can be concluded that the synergies between the plasma and the conductive catalysts need to be reassessed for different electric field conditions, and that further studies of non-conductive catalysts that can enhance methane activation and synergistic effects are needed.     

Catalytic Performance and Characterization of Pt‐Co/Al2O3 Catalysts for CO2 Reforming of CH4 to Synthesis Gas

Pt‐Co/Al₂O₂ catalyst has been studied for CO₂ reforming of CH₄ to synthesis gas. It was found that the catalytic performance of me catalyst was sensitive to calcination temperature. When Co/Al₂O₃ was calcined at 1473 K prior to adding a small amount of Pt to it, the resulting bimetallic catalyst showed high activity, optimal stability and excellent resistance to carbon deposition, which was more effective to the reaction than Co/Al₂O₃ and Pt/Al₂O₃ catalysts. At lower metal loading, catalyst activity decreased in the following order: Pt‐Co/ Al₂O₃ > Pt/Al₂O₃ > Co/Al₂O₃. With 9% Co, the Co/Al₂O₃ calcined at 923 K was also active for CO₂ reforming of CH₄, however, its carbon formation was much more fast man that of the Pt‐Co/Al₂O₃ catalyst. The XRD results indicated that Pt species well dispersed over the bimetallic catalyst. Its high dispersion was related to the presence of CoAl₂O₄, formed during calcining of Co/Al₂O₃ at high temperature before Pt addition. Promoted by Pt, Co/Al₂O₄ in the catalyst could be reduced partially even at 923 K, the temperature of pre‐reduction for the reaction, confirmed by TPR. Based on these results, it was considered that the zerovalent platinum with high dispersion over the catalyst surface and the zerovalent cobalt resulting from Co/Al₂O₄ reduction are responsible for high activity of the Pt‐Co/Al₂O₃ catalyst, and the remain Co/Al₂O₄ is beneficial to suppression of carbon deposition over the catalyst.     

Isomerization ofn-pentane andn-hexane on modified zeolites

The activity and selectivity of catalysts based on TsVM (an analog of ZSM-5), Beta, and La-H-Beta zoelites modified by Pt, Pt−Fe, and Pt−Ga were studied in the isomerization of C₅ and C₆ linear alkanes. The Pt/HTsVM, Pt/H-Beta, and Pt/La-H-Beta catalysts are efficient inn-pentane isomerization, whereas the Pt/H-Beta and Pt/La-H-Beta are most active inn-hexane isomerization. Nearly equilibirum isoparaffin yield at a selectivity of at least 95–96% is reached on these catalysts unlike other zeolite systems. The overall yield of 2,2-and 2,3-dimethylbutanes is 22 wt.%. The hexane isomers are not formed over the Pt/HTsVM catalyst due to the molecular-sieve properties of this type of zcolites. Published inIzvestiya Akademii Nauk. Seriya Khimicheskaya No. 11, pp. 1866–1869, November, 2000.     

Ni3FeN‐Supported Fe3Pt Intermetallic Nanoalloy as a High‐Performance Bifunctional Catalyst for Metal–Air Batteries

Electrocatalysts for both the oxygen reduction and evolution reactions (ORR and OER) are vital for the performances of rechargeable metal–air batteries. Herein, we report an advanced bifunctional oxygen electrocatalyst consisting of porous metallic nickel‐iron nitride (Ni₃FeN) supporting ordered Fe₃Pt intermetallic nanoalloy. In this hybrid catalyst, the bimetallic nitride Ni₃FeN mainly contributes to the high activity for the OER while the ordered Fe₃Pt nanoalloy contributes to the excellent activity for the ORR. Robust Ni₃FeN‐supported Fe₃Pt catalysts show superior catalytic performance to the state‐of‐the‐art ORR catalyst (Pt/C) and OER catalyst (Ir/C). The Fe₃Pt/Ni₃FeN bifunctional catalyst enables Zn–air batteries to achieve a long‐term cycling performance of over 480 h at 10 mA cm⁻² with high efficiency. The extraordinarily high performance of the Fe₃Pt/Ni₃FeN bifunctional catalyst makes it a very promising air cathode in alkaline electrolyte.     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

Bimetallic Pd—Pt/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for complete methane oxidation: the effect of the Pt: Pd ratio

Alumina-supported bimetallic Pt—Pd catalysts proved to be more active in the complete oxidation of methane than monometallic systems (Pt/Al₂O₃, Pd/Al₂O₃). The maximum activity of the bimetallic catalysts was achieved at ~40 at.% Pt in Pd on the catalyst surface. After the oxidation reaction, redistribution of platinum and palladium was observed in the active component of the catalysts with the degree of redistribution depending on the initial Pt: Pd ratio.