APS/NaClO 复合氧化剂对乳液法合成聚苯胺的微观形貌及其电化学性能的影响

采用乳液法, 以过硫酸铵(APS)和次氯酸钠(NaClO)为复合氧化剂合成导电聚苯胺(PANI). 考察了NaClO 的加入与否对PANI 微观形貌与电化学性能(循环伏安和电导率)的影响, 以及APS、乳化剂十二烷基苯磺酸钠(SDBS)和NaClO的用量对PANI 电化学性能的影响. 结果表明: NaClO 的加入对PANI 的微观取向结构具有重要的影响. 与采用单一APS 合成的PANI 相比, 复合氧化剂合成的PANI 具有较高的循环伏安峰电流以及更加优异的电导率(约为前者的2.6倍). 当苯胺(An)与APS 的物质的量比(n_An:n_APS )为8:7, An 与SDBS 的物质的量比(n_An:n_SDBS )为10:4, NaClO 用量为5%(质量分数)时, PANI 的各项性能指标达到最好; 紫外可见光谱和红外光谱的表征结果表明, 采用复合氧化剂并未对PANI 的分子结构产生明显的影响.     

复合乳化剂微乳液法制备聚苯胺及其电化学性能

采用复合乳化剂微乳液法合成了导电聚苯胺(PANI),以碳纸负载PANI为工作电极,考察了十二烷基苯磺酸钠(SDBS)和聚乙二醇辛基苯基醚(TX-100)的配比及其复合乳化剂(E)和氧化剂(APS)用量对复合乳化剂微乳液法合成PANI电化学性能(循环伏安、塔费尔)的影响;通过对产物电导率和产率的对比分析,印证了PANI电化学性能表征结果的有效性。结果表明：当SDBS与TX-100的质量比为1/2,E与苯胺(An)单体的质量比为5/3,APS与An的摩尔比为1.2时,PANI的各项性能指标达到最好,且产物的循环伏安峰电流、腐蚀电位和电导率均高于单组分乳化剂SDBS或TX-100微乳液法制备的PANI。     

磁场对复配乳化剂/苯胺微乳液聚合体系相行为的影响

首次在酸性条件下, 以十二烷基苯磺酸钠(SDBS)和聚乙二醇辛基苯基醚(TX-100)为复配乳化剂, 制备SDBS/TX-100/正丁醇(nBA)/苯胺(An)/盐酸(HCl)微乳液体系, 并通过该体系的拟三元相图, 考察了恒定磁场(0.4 T)、助表面活性剂(nBA)与复配乳化剂的质量比(K_m＝m_nBA/m_SDBS/TX-100)及SDBS与TX-100的质量比(S_m＝m_SDBS/m_TX-100)对复配乳化剂/苯胺微乳液聚合体系相行为和电导行为的影响. 结果表明: 随着K_m的增加, 微乳区面积先增大后减小, 当K_m＝1.0时, 形成的微乳区面积最大|随着S_m的减少, 微乳区面积逐渐增大|外加磁场可以增大微乳区面积, 且随着S_m的减小, 磁场对微乳液体系的作用逐渐减弱. 循环伏安的测试结果表明, 复合乳化剂微乳液法制备的聚苯胺, 其循环伏安性能优于单组分乳化剂(SDBS或TX-100)微乳液法制备的聚苯胺.     

一步乳液聚合法制备高溶解性导电聚苯胺

报道了一种高溶解性导电聚苯胺(PANI)的制备方法,以聚2-丙烯酰胺-2-甲基丙磺酸(PAMPS)作为掺杂酸和乳化剂,利用其特有的长链、亲水性及强酸性基团效应,通过乳液聚合法一步合成出具有较高溶解性的导电聚苯胺。利用核磁共振光谱仪(NMR)、傅里叶红外光谱仪(FT-IR)和扫描电子显微镜(SEM)等技术手段对产物结构和性能进行了表征分析。结果表明,在m(苯胺)∶m(AMPS)∶m(APS)=1∶2∶1.5;AMPS质量分数为20%;APS质量分数为30%;反应时间为5 h;反应温度为5℃的条件下,聚苯胺的产率高达86%,在有机溶剂二甲基甲酰胺(DMF)中的溶解度可达0.3814 g/g,在水中的溶解度可达0.2123 g/g,电导率达5.9 S/cm。     

不同酸掺杂聚苯胺电极材料的制备及其导电性能研究

本文使用(NH_4)_2S_2O_8为氧化剂,用HCl、H_2SO_4和磷钨酸作为掺杂剂配制前驱体溶液,然后采用氧化还原法制备了聚苯胺电极材料。通过红外(FT-IR)、X射线衍射(XRD)、热重分析(TGA0)及扫描电子显微镜(SEM)对电极材料的结构和形貌进行表征,并利用四探针方法测定聚苯胺电极材料在控制氧化剂的量、酸的浓度和不同温度条件下的电导率。结果表明,磷钨酸掺杂聚苯胺(PANI)的结构和形貌优于HCl和H_2SO_4掺的PANI,过硫酸铵(APS)与苯胺(An)的摩尔比为1∶1、酸的浓度为2 mol·L~(-1)、合成温度为0℃的条件下,PANI具有高电导率,分别达到10.27、9.62和8.79S·cm~(-1)。     

氧化-温控双功能离子液体催化O2氧化模拟柴油脱硫

将温控结构单元聚醚链和催化氧化基团磷钨酸根共同引入到离子液体的结构中, 合成出一系列不同聚合度的十八胺类氧化-温控双功能离子液体, 并将其应用于催化O₂氧化模拟柴油的脱硫反应过程, 实现了反应分离一体化, 并取得了良好的脱硫效果和催化剂循环使用效果. 该类离子液体在甲苯/正十二烷混合溶剂中具有良好的温控性能. 筛选出活性较高的离子液体催化剂, 其聚合度n=111以及烷基碳链为C₁₂. 考察了反应温度、反应时间和氧气压力等因素对脱硫效果的影响. 在优化的反应条件(V(甲苯):V(模拟油)=1:1, T=100 ℃, t=2 h, p(O₂)=2.0 MPa)下, DMF萃取一次, 脱硫率接近100%. 催化剂循环使用11次, 脱硫率仍可达到95%以上.     

原位聚合法制备PANI/PET导电织物及其性能分析

在聚酯纤维基材及其织物表面,原位聚合形成厚度约1~2μm聚苯胺包覆层,制得聚苯胺(PANI)/聚酯(PET)导电织物.PANI层优异的导电性能使之成为有广阔发展前景的柔性电磁屏蔽材料.正交试验分析研究了苯胺单体浓度、氧化剂:苯胺摩尔比、掺杂酸浓度、反应时间对PANI包覆层外观形态、与基体结合牢度以及导电性的影响.实验表明:在经适当前处理的PET基材表面,以苯胺单体浓度为0.25mol/L、氧化剂与苯胺摩尔比为1∶1、掺杂酸浓度0.5 mol/L、反应时间60 min、反应温度为0~20℃时制备的PANI/PET导电织物方阻最小,导电性最好;掺杂酸酸性越强,导电性越好.SEM、FTIR及XRD测试表明涤纶织物表面有均匀连续的聚苯胺膜存在.分析表明聚苯胺分子链中氧化结构与还原结构含量基本相等,说明聚苯胺渗入纤维内部,使纤维无定形区面积增加,结晶度减小.     

聚苯乙烯磺酸掺杂聚苯胺的合成

以苯胺（An）为单体，过硫酸铵（APS）为氧化剂，在聚苯乙烯磺酸（PSSA）的水溶液中，合成了可完全溶于水的PSSA掺杂PAn。研究了An浓度，PSSA浓度，APS浓度，APS的滴加时间，反应时间及温度对An聚合反应及其产物的水溶性，导电性及特性粘度[η]的影响。结果表明：在比较宽的实验条件下，都可以合成出具有良好导电性的可溶于水的PSSA掺杂PAn；其中当An：PSSA:APS的摩尔比为1．7：2．5：1，APS溶液的滴加时间为3h，反应时间为1h，反应温度为14℃时，得到的掺杂PAn导电率最高达0．156S／cm。     

一维有序聚苯胺纳米阵列的制备及电化学储能性能

以导电玻璃FTO为基底电极, 在硫酸溶液中, 分别研究了苯胺单体浓度和恒定电流大小对聚苯胺(PANI)形貌的影响; 同时恒定苯胺单体的浓度和工作电流, 探究了不同类型的质子酸对PANI阵列形貌的影响. 结果表明, 采用恒电流方法可以制备出一维有序PANI纳米线阵列, 而且当苯胺的浓度为0.1 mol/L, 恒电流法的工作电流密度为0.03 mA/cm²时, 所制备的PANI纳米线阵列形貌最佳; 当用HCl, HNO₃和对甲苯磺酸(p-TSA)作为合成PANI的支持液时, 得到树桩状的PANI 纳米结构, 不能得到均一的纳米线阵列结构. 电化学性能测试结果表明, 制备的最佳形貌PANI纳米线阵列的比电容值可达560 F/g; 循环1000周后电容损失率为11%.     

镝掺杂铁氧体纳米晶的制备、表征和磁性

采用化学共沉淀法制备出了镝掺杂铁氧体纳米晶, 利用透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅立叶红外光谱仪(FTIR)、古埃磁天平、振动样品磁强计(VSM)、X射线能谱仪(EDX)等仪器对产物进行了表征, 研究了Dy^3＋掺杂量对铁氧体纳米晶的结构、磁性和粒度的影响. 结果表明: 适量稀土元素镝离子的掺杂可以提高尖晶石型铁氧体的磁性、降低矫顽力, 当n(Fe^3＋)∶n(Dy^3＋)＝14∶1时其磁性最强. Dy^3＋替代或充填进入了尖晶石晶格, 且主要占据B位. 掺杂了镝的铁氧体磁性纳米粒子粒度变小, 且分布更集中、均匀, 当Dy^3＋加入量为n(Fe^3＋)∶n(Dy^3＋)＝14∶1时铁氧体纳米粒子的平均粒径由掺杂前的14 nm降低到到8 nm. 这种具有超顺磁性的软磁铁氧体纳米晶可应用于纳米磁液领域.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.