Countering matrix effects in environmental liquid chromatography-electrospray ionization tandem mass spectrometry water analysis for endocrine disrupting chemicals

In recent years, despite the increasing success of liquid chromatography (LC) coupled to tandem mass spectrometry (MS), reports on matrix susceptibility have shown the limitations of the this powerful analytical technique. Matrix effects (MEs) result from co-eluting residual matrix components affecting the ionization efficiency of target analytes and can lead to erroneous results. The present work evaluates the matrix effect of environmental water samples on 35 endocrine disrupting chemicals (EDCs) in negative and positive LC-ESI-MS/MS. It was shown that mobile-phase additives could significantly influence matrix effects. Addition of acids resulted in a severe signal suppression (average ME%: <65%), and 1 mM ammonium formate increased the average ME% to 84%. The importance of an efficient sample clean-up and internal standardization also was demonstrated. Cleaner extracts resulted in reduced matrix effects (average ME%: 89%) and labeled internal standards proved to have a beneficial effect especially on signal reproducibility (average CV% 4.2% versus 2.6%). The results from the present work indicate that evaluation of matrix effects should become an integrated part of quantitative LC-ESI-MS/MS method development and validation.     

Determination of perfluorinated compounds in wastewater and river water samples by mixed hemimicelle-based solid-phase extraction before liquid chromatography-electrospray tandem mass spectrometry detection

A comparative study on the use of cetyltrimethylammonium bromide (CTAB)-coated silica and sodium dodecyl sulphate (SDS)-coated alumina mixed hemimicelles-based solid-phase extraction (SPE) for the pre-concentration of six perfluorinated compounds (PFCs) in environmental water samples was presented. The six analytes heptafluorobutyric acid (HFBA), perfluoroheptanic acid (PFHeA), perfluorooctanic acid (PFOA), perfluorooctanic sulfonic (PFOS), perfluorononanic acid (PFNA) and perfluorodecanic acid (PFDeA) were quantitatively retained on both sorbent materials. The cationic surfactant (CTAB adsorbed onto silica) was more appropriate for SPE of PFCs. The main factors affecting adsolubilization of PFCs including the amount of surfactant, pH of solution, sample loading volume and desorption were investigated and optimized. Concentration factor of 500 were achieved by SPE of 500 mL of several environmental water samples. The method detection limits obtained for HFBA, PFHeA, PFOA, PFOS, PFNA and PFDeA were 0.10, 0.28, 0.07, 0.20, 0.10 and 0.05 ng/L, respectively. The relative standard deviation of recoveries ranged from 2 to 8%, which indicated good method precision.     

Quantitative determination of perfluorinated surfactants in water by LC-ESI-MS/MS

The surfactants perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), and derivatives of the latter have emerged as globally distributed persistent environmental contaminants. Methods for their reliable quantitative determination at ppt-levels (ng/L) are needed in order to detect their main sources, to elucidate their environmental fate, and to identify potential sinks. The common method for water analysis involves preconcentration by SPE followed by LC coupled to ESI MS/MS (LC-ESI-MS/ MS). All sample preparation steps must be carefully optimized in order to arrive at reliable quantitative data. Two major aspects are important: (i) during SPE, contaminations may arise from materials containing traces of PFOA/S; (ii) during LC-ESI-MS/ MS, ionization yields are suppressed by matrix components and depend upon the analyte concentrations in the extracts. The levels of PFOA/S in the river Roter Main near Bayreuth have been determined using the optimized method.     

Solid-phase extraction clean-up of soil and sediment extracts for the determination of various types of pollutants in a single run

A new sample clean-up procedure based on solid-phase extraction (SPE) sorbents was proposed for the determination of pesticides, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in soils and sediments. The main purpose of the research was to find a combination of sorbents for the SPE method that would permit the determination of many types of analytes (polycyclic aromatic hydrocarbons, polychlorinated biphenyls, N-, P- and Cl-containing pesticides) in a single run. Elution profiles for both the analytes and the interfering components were determined for several types of SPE sorbents (alumina, silica and surface-modified silica) and combinations of them. The efficiency of the clean-up method developed was evaluated using real soil samples.     

On-line SPE-Nano-LC-Nanospray-MS for rapid and sensitive determination of perfluorooctanoic acid and perfluorooctane sulfonate in river water

An instrumental set up including on-line solid-phase extraction, nano-liquid chromatography, and nanospray mass spectrometry is constructed to improve the sensitivity for quantitation of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in surface water. Sample volumes of 1000 microL are loaded onto a microbore 1.0-mm i.d. x 5 mm, 5 microm Kromasil C(18) enrichment column by a carrier solution consisting of 10mM ammonium acetate in acetonitrile-water (10:90, v/v) at a flow rate of 250 microL/min, providing on-line analyte enrichment and sample clean-up. Backflushed elution onto a 0.1-mm i.d. x 150 mm, 3.5 microm Kromasil C(18) analytical column is conducted using an acetonitrile-10mM ammonium acetate solvent gradient from 30% to 70% acetonitrile. Water samples are added with internal standard (perfluoroheptanoic acid) and filtrated prior to injection. The mass limits of detection of PFOA and PFOS are 0.5 and 1 pg, respectively, corresponding to concentration limits of detection of 500 pg/L and 1 ng/L, respectively. The total time spent on sample preparation, chromatography, and detection is approximately 12 min per sample. The method was employed for the determination of PFOS and PFOA in urban river water.     

On-line preconcentration of perfluorooctanoic acid and perfluorooctanesulfonic acid by nonaqueous capillary electrophoresis

Separation of major environmental pollutants as perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) by capillary electrophoresis is reported for the first time. It is not possible to resolve the solutes in an aqueous media. However, the use of methanol and acetonitrile as the background electrolyte (BGE) solvents allowed their rapid separation in an uncoated capillary. A major effort was put into BGE optimization in respect to both separation efficiency and detection for further on‐line preconcentration. 5 mmol.L^?1 naphthalene‐1‐sulfonic acid and 10 mmol.L^?1 triethylamine dissolved in ACN/MeOH (50:50 v/v) provided best separation and detection conditions. Next, the large‐volume sample stacking and the field‐amplified sample injection were applied and compared. Large‐volume sample stacking improved limits of detection (LODs) with regard to the standard injection by 69 times for PFOA and 143 times for PFOS with LODs of 280 and 230 nmol.L^?1, respectively. Field‐amplified sample injection improved LODs 624 times for PFOAand 806 times for PFOS with LODs 31 and 40 nmol.L^?1, respectively. Both preconcentration methods showed repeatabilities of migration times less than 1.2% RSD intraday and 6.6% RSD interday. The method was applied on PFOA and PFOS analysis in a sample of river water treated with solid‐phase extraction, which further improved LOD toward 5.6 × 10^?10 mol.L^?1 for PFOS and 6.4 × 10^?10 mol.L^?1 for PFOA and allows the method to be used for river water contamination screening or decomposition studies.     

Analysis of perfluorooctanesulfonate and related fluorochemicals in water and biological tissue samples by liquid chromatography-ion trap mass spectrometry

A method for the determination of perfluorinated compounds (PFCs) in various water and biological tissue samples was developed and validated. The contents of selected PFCs (i.e., perfluorooctanesulfonate (PFOS), perfluorooctanoate (PFOA) and perfluorodecanoate (PFDA)) in water samples were extracted by the C(18) solid-phase extraction (SPE). The biological tissue samples (frozen-dried fish and oysters) were simply extracted by liquid-solid extraction with MTBE and adding tetrabutylammonium hydrogensulfate (TBA) as an ion-pairing reagent. The analytes were then identified and quantitated by liquid chromatography-ion trap negative electrospray mass spectrometry (LC-ESI ion-trap-MS). Limits of quantitation (LOQ) were established between 0.5 and 6 ng/l in 250 ml of water sample, while 5-50 ng/g (dry weight) for biological tissue sample. Intrabatch and interbatch precision with their accuracy at two concentration levels were also investigated. Precision for these three PFCs, as indicated by RSD, proved to be less than 11 and 17%, respectively. The total contents of PFOA, PFOS and PFDA were detected in concentrations of up to 400 ng/l in various water samples, while up to 1,100 ng/g in fish and oyster samples. PFOA and PFDA was the major PFCs detected in water samples and biological tissue samples, respectively.     

Extraction and clean-up strategies for the analysis of poly- and perfluoroalkyl substances in environmental and human matrices

The rapidly expanding field of per- and polyfluorinated alkyl substances (PFASs) research has resulted in a wide range of analytical methodologies to determine the human and environmental exposure to PFASs. This paper reviews the currently applied techniques for sample pre-treatment, extraction and clean-up for the analysis of ionic and non-ionic PFASs in human and environmental matrices. Solid phase extraction (SPE) is the method of choice for liquid samples (e.g. water, blood, serum, plasma), and may be automated in an on-line set-up for (large volume) sample enrichment and sample clean-up. Prior to SPE, sample pre-treatment (filtration or centrifugation for water or protein precipitation for blood) may be required. Liquid-liquid extraction can also be used for liquid samples (and does not require above mentioned sample pretreatment). Solid-liquid extraction is the commonly applied method for solid matrices (biota, sludge, soil, sediment), but automation options are limited due to contamination from polytetrafluorethylene tubings and parts applied in extraction equipment. Air is generally preconcentrated on XAD-resins sandwiched between polyurethane foam plugs. Clean-up of crude extracts is essential for destruction and removal of lipids and other co-extractives that may interfere in the instrumental determination. SPE, (fluorous) silica column chromatography, dispersive graphitized carbon and destructive methods such as sulphuric acid or KOH treatment can be applied for clean-up of extracts. Care should be taken to avoid contamination (e.g. from sample bottles, filters, equipment) and losses of PFASs (e.g. adsorption, volatilization) during sampling, extraction and clean-up. Storage at -20 degrees C is generally appropriate for conservation of samples.     

Determination of perfluorooctanoate and perfluorooctanesulfonate in water matrices by inline matrix elimination liquid chromatography with reversed phase separation and suppressed conductivity detection

This work describes a new method for the determination of perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) in water matrices by suppressed conductivity detection. Separation was achieved by isocratic elution on a reversed-phase column thermostated at 45°C using an aqueous mobile phase containing boric acid and acetonitrile. The PFOA and PFOS content in the water matrix were quantified by a pre-concentration technique. For the concentration range of 1 to 15 ng/mL and 2 to 30 ng/mL, the linear calibration curve for PFOA and PFOS yielded coefficients of determination (R(2)) of 0.9995 and 0.9985, respectively. The relative standard deviations were smaller than 1.5% for PFOA and PFOS. The retention-time precision of four consecutive 12 h injections was smaller than 0.641% and 0.818%, respectively. The presence of common divalent cations, such as calcium, magnesium, and iron in water matrices impairs PFOS recovery. This drawback was overcome by applying inline matrix elimination method. The optimized method was successfully applied for drinking water, ground water, and seawater samples.     

Sample pretreatment method for the determination of polychlorinated biphenyls in bird livers using ultrasonic extraction followed by headspace solid-phase microextraction and gas chromatography-mass spectrometry

A simple and reliable sample methodology based on simultaneous ultrasonic extraction, sulfuric acid clean-up and headspace solid-phase microextraction (SPME)-gas chromatography-mass spectrometry has been developed as an advantageous analytical tool for the determination of seven polychlorinated biphenyl congeners in bird livers at low levels. The influence of several parameters on the efficiency of the proposed method was systematically investigated. The clean-up efficiency of sulfuric acid treatment was tested and compared with those of column chromatography (Flosiril, silica gel and alumina) and solid-phase extraction (SPE) (Supelclean ENVI-Carb cartridge) procedures. The use of sulfuric acid in the clean-up step prior to headspace solid-phase microextraction analysis allows the removal of interfering matrix compounds present in the liver extracts that would otherwise cause severe ionization suppression of the polychlorinated biphenyls (PCBs) during the ionization process. The optimized method had good linearity (R2>0.99) over the range studied (5-500 ng/g wet weight) and showed satisfactory level of precision, with RSD values lower than 10.6%. The obtained relative recoveries ranged between 63 and 94%. The limits of detection (0.06-0.63 ng/g wet weight) were low enough to check for harmful levels of polychlorinated biphenyls in biological samples, and were well below most of the restrictive limits established by European Union regulations. The method was found to be reliable under the operational conditions proposed and was applied successfully to the analysis of individual polychlorinated biphenyls in liver tissues. The results obtained from five bird species from Greece revealed the presence of the target compounds in all samples analyzed, at levels ranging between 0.54 and 39.45 ng/g wet weight.     

Determination of Perfluorochemicals in Human Milk Using Isotope‐dilution Liquid Chromatography Tandem Mass Spectrometry

A highly precise and accurate analytical method utilizing an isotope‐dilution liquid chromatography tandem mass spectrometry was developed and validated to determine two perfluorochemicals (PFCs): perfluorooctanoate (PFOA) and perfluorooctanesulfonate (PFOS) in human milk samples. Identification of the analytes was confirmed under negative electrospray with multiple reaction monitoring (MRM) mode by the monitoring of one precursor ion and two product ions, and matching of relative ion intensities of the ions concerned in samples and calibration standards. Quantitation was based on the measurement of concentration ratios of the natural and labeled‐analogues in the samples and calibration mixtures. The isotope‐labeled internal standards were also used to correct the matrix effect and variations associated with the analysis. Intra‐ and inter‐day repeatabilities of replicate analyses of the PFOA and PFOS in milk samples were below 8%. The limit of quantitation was 2 pg/mL in a 5 mL milk sample. The PFOA and PFOS were detected in all 20 human milk samples at concentrations from 27.0 to 207 pg/mL. This is the first study to measure the occurrence of PFOA and PFOS in human milk from Taiwan.     

Determination of perfluorooctane sulfonate and perfluorooctanoic acid in human plasma by large volume injection capillary column switching liquid chromatography coupled to electrospray ionization mass spectrometry

Rapid, selective, and sensitive methodology for the quantification of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in human plasma using packed capillary liquid chromatography coupled to electrospray ionization ion-trap mass spectrometry has been developed. Plasma proteins were precipitated using acetonitrile and the resulting supernatant was diluted 1+1 with water containing 10 mM ammonium acetate (NH4Ac) prior to injection. Sample volumes of 250 microL were loaded onto a 30 mm x 0.32 mm ID 10 microm Kromasil C18 precolumn by a carrier solution consisting of 10 mM NH4Ac in ACN/H2O (5/95, v/v) at a flow rate of 100 microL/min, providing on-line analyte enrichment and sample clean-up. Backflushed elution onto a 100 mm x 0.32 mm ID 3.5 microm Kromasil C18 analytical column was conducted using an ACN/H2O solvent gradient containing 10 mM NH4Ac. In order to improve the robustness and performance of the method, perfluoroheptanoic acid (PFHA) was used as internal standard. Separation and detection of PFOA, PFHA, and PFOS were achieved within 10 minutes. Ionization was performed in the negative mode in the m/z range 250-550. The method was validated over the concentration range 1-200 ng/mL for PFOA and over the range 5-200 ng/mL untreated plasma for PFOS, yielding correlation coefficients of 0.997 (PFOA) and 0.996 (PFOS), respectively. The within-assay (n = 6) and between-assay (n = 6) precisions were in the range 2.1-9.2 and 5.6-12%, respectively. The concentration limits of detection (cLOD) of PFOA was 0.5 ng/mL while the cLOD of PFOS was estimated to be 0.2 ng/mL in untreated plasma.     

Tackling matrix effects during development of a liquid chromatographic-electrospray ionisation tandem mass spectrometric analysis of nine basic pharmaceuticals in aqueous environmental samples

When developing an LC-MS/MS-method matrix effects are a major issue. The effect of co-eluting compounds arising from the matrix can result in signal enhancement or suppression. During method development much attention should be paid to diminish matrix effects as much as possible. The present work evaluates matrix effects from aqueous environmental samples in the simultaneous analysis of a group of nine specific pharmaceuticals with LC-ESI/MS/MS: flubendazole, propiconazole, pipamperone, cinnarizine, ketoconazole, miconazole, rabeprazole, itraconazole and domperidone. Solutions to diminish signal suppression were examined: optimisation of the sample preparation, decrease of the flow rate, and the use of appropriate internal standards. Several SPE-stationary phases were tested in view of retention of the analytes: Oasis HLB, C8, Phenyl, Strata X-polymer RP sorbent and Strata X-polymeric SCX/RP sorbent. Oasis HLB showed the best retention for all analytes. The Oasis HLB SPE-method was optimised, but analyses showed high matrix suppression. Therefore, a second SPE-method, on a phenyl stationary phase (the second best option), was also optimised. A comparison of the matrix effect was made between the two procedures: the phenyl-method was less subject to matrix effects, however, the average matrix effect (ME%) of 46% indicated that matrix effects where still present. Several optimisation options for the phenyl-method were evaluated: addition of a ferric nitrate solution before extraction, application of an alkaline wash step, and use of a second SPE-cartridge, either a NH2-column or a florisil column. A more efficient sample clean-up was achieved by applying the extract after extraction on the phenyl column and after dilution with chloroform, onto a NH2-column (average ME%: 53%). In addition, applying a post-column split (1:5), further reduced matrix effects (average ME%: 65%). Labelled internal standards are the best way to tackle matrix effects, but no such internal standards were commercially available for the analytes of interest. The thorough search and application of four internal standards (structural analogues) was beneficial and compensates the matrix effect partially (average ME%: 83%). In an attempt to reduce the analysis time Speedisk phenyl columns were applied. Under these conditions matrix effects decreased even more while recoveries were between 91 and 109%. Different kinds of surface water samples were analyzed, and different matrix effects were observed. For this reason, standard addition will be used to perform quantitative analysis.     

Solid-phase extraction of PFOA and PFOS from surface waters on functionalized multiwalled carbon nanotubes followed by UPLC–ESI-MS

This is the first report on the analytical application of multiwalled carbon nanotubes (MWCNTs) as solid-phase extraction (SPE) sorbents for determination in surface waters, at the nanograms per litre level, of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), the two predominant contaminants among the perfluorinated compounds detected. After the preconcentration step, the quantification was achieved by ultraperformance liquid chromatography–electrospray ionization mass spectrometry. To increase the extraction efficiency towards these amphiphilic compounds, MWCNTs were derivatized with amino-terminated alkyl chains, thus producing a mixed-mode material (MWCNT-R-NH₂) combining hydrophobic affinity and anion-exchange properties. Experiments with distilled, tap and river water (pH 3) spiked at different concentrations (10, 15, 30, 100, 200 and 500 ng L^-1) provided absolute recoveries in the range 71–102 % (n?=?3, relative standard deviations less than 10 %). Analytes were eluted in a single fraction with 6 mL methanol (3?×?10^-4 M NaOH). The within-laboratory reproducibility of the MWCNT-R-NH₂ SPE sorbent was evaluated with raw river water, and relative standard deviations less than 15 % were obtained (n?=?4). Preconcentration factors up to 125 (500-mL sample) made it possible to quantify PFOA and PFOS at low nanograms per litre levels in naturally contaminated river water. The method quantification limits of 10 ng L^-1 for PFOA and 15 ng L^-1 for PFOS were well below the advisory levels for drinking and surface waters. Comparison with non-derivatized MWCNTs highlighted the role of functionalization in improving the adsorption affinity towards these contaminants. MWCNT-R-NH₂ maintained their extraction capability for at least eight repeated adsorption/desorption cycles.     

A solid-phase extraction procedure for the clean-up of thiram from aqueous solutions containing high concentrations of humic substances

A simple solid-phase extraction (SPE) procedure with an octadecyl bonded phase silica (C₁₈) was developed for clean-up of the fungicide thiram from aqueous solutions containing high concentrations of humic substances, for future studies of thiram adsorption onto solid humic substances or soils. Suspensions of humic acids and soil, in aqueous 0.01 M CaCl₂ solution, were prepared and used as samples. These extracts were spiked with thiram and immediately applied to a C₁₈-SPE cartridge. Thiram was eluted with chloroform and its concentration measured by spectrophotometry at 283 nm. Non-spiked aqueous extracts (blanks) and a control sample of thiram in 0.01 M CaCl₂ aqueous solution were also prepared and submitted to the same SPE procedure. The results show that humic substances are extensively retained by the C₁₈ cartridge but are not eluted with CHCl₃. Recoveries of 100-104% were obtained for thiram in the presence of humic substances. The SPE procedure described in this work is an efficient clean-up step to remove the interference of humic substances absorbance and to be coupled to any spectrophotometric or HPLC-UV method, usually used for thiram analysis in food extracts.     

应用于全氟辛烷磺酸萃取富集的全氟癸基修饰毛细管硅胶整体柱的制备及应用

利用溶胶-凝胶法,经过烷氧基硅烷的水解、硅羟基的缩聚、凝胶化、陈化、中孔制备、干燥和表面修饰等步骤制备了全氟癸基修饰的毛细管硅胶整体柱。采用该整体柱对全氟辛烷磺酸(PFOS)进行萃取富集,考察其富集特性和效率,并与传统的C18毛细管硅胶整体柱进行对比。结果表明,全氟癸基修饰毛细管硅胶整体柱(15 cm×75 μm)对PFOS具有更高的吸附量和更好的富集选择性,其平均吸附量可以达到75 ng;样品中PFOS的质量浓度为0.25 mg/L时,富集倍数平均可以达到29倍。此全氟癸基修饰毛细管硅胶整体柱对PFOS具有良好的萃取富集性能,可用于水质中痕量PFOS的萃取富集。     

Investigation of Matrix Effects on the Determination of Carbadox and Olaquindox in Feed by LC–MS/MS

A comprehensive survey of matrix effects on the LC–MS/MS analysis of the banned antibiotic growth promoters carbadox and olaquindox in feed was carried out. Various factors of sample preparation procedure and measurement were systematically investigated by pre- and post-extraction addition and postcolumn infusion experiments. In general, strong signal suppression up to 70 % for carbadox and up to 90 % for olaquindox was observed when using different extraction solvents and techniques as well as different chromatographic conditions. Reduction of matrix effects was achieved by SPE clean-up and dilution of sample extracts. Nevertheless, matrix effect profiles determined by postcolumn infusion revealed, that reduction of signal suppression at a respective retention time cannot guarantee improvement of the methods performance. If high variability of matrix effects is present along the chromatographic run, accuracy might decrease despite reduced signal suppression. Besides method parameters, different feedingstuffs were investigated and showed similar matrix effects.     

Investigation of Matrix Effects on the Determination of Carbadox and Olaquindox in Feed by LC–MS/MS

A comprehensive survey of matrix effects on the LC–MS/MS analysis of the banned antibiotic growth promoters carbadox and olaquindox in feed was carried out. Various factors of sample preparation procedure and measurement were systematically investigated by pre- and post-extraction addition and postcolumn infusion experiments. In general, strong signal suppression up to 70 % for carbadox and up to 90 % for olaquindox was observed when using different extraction solvents and techniques as well as different chromatographic conditions. Reduction of matrix effects was achieved by SPE clean-up and dilution of sample extracts. Nevertheless, matrix effect profiles determined by postcolumn infusion revealed, that reduction of signal suppression at a respective retention time cannot guarantee improvement of the methods performance. If high variability of matrix effects is present along the chromatographic run, accuracy might decrease despite reduced signal suppression. Besides method parameters, different feedingstuffs were investigated and showed similar matrix effects.

     

Gas chromatography-mass spectrometric determination of polybrominated diphenyl ethers in complex fatty matrices from aquaculture activities

Gas chromatography coupled to mass spectrometry in negative chemical ionization mode (GC-(NCI)MS) has been applied to the quantification and reliable identification of polybrominated diphenyl ethers (PBDEs) in animal and vegetable samples from aquaculture activities. Matrices analyzed included fish fillet, fish feed, fish oil and linseed oil, their fat content ranged from 5% to 100%. Solid-phase extraction (SPE) (using Florisil and silica cartridges) and normal-phase high performance liquid chromatography were tested for an efficient clean-up in order to obtain sample extracts free of interfering compounds. Combining sulphuric acid digestion and SPE with Florisil led to the highest efficiency in the elimination of interferences from the extracts. The sample procedure developed, together with the application of GC-(NCI)MS for measurement, led to the satisfactory determination of PBDEs at μg kg ⁻¹ levels in complex aquaculture matrices with high lipid content. The use of a short and thin film-thickness fused-silica capillary column allowed to determine the problematic BDE 209 with satisfactory results. Three m/z ions were acquired for each analyte, which ensured a reliable identification of compounds detected in samples.     

Determination of perfluorooctanesulfonate and perfluorooctanoate in water samples by SPE-HPLC/electrospray ion trap mass spectrometry

Perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) are the most notable members of an emerging class of persistent organic pollutants (POPs), perfluorochemicals (PFCs). A method for the determination of PFOS and PFOA in water samples was developed and validated in this study. Water samples collected from river and industrial effluent at Guangzhou, one of the most industrialized regions in China, were analyzed by solid-phase extraction (SPE) followed by high-performance liquid chromatography (HPLC) negative electrospray ionization (ESI) mass spectrometry. Operational parameters of the ion trap mass spectrometer were optimized to improve sensitivity and selectivity of this method. The limits of quantitation and recoveries were 2.0 ng L^− 1 and 75% for PFOA and 0.50 ng L^− 1 and 88% for PFOS, respectively. In river water samples, 2.3-33 ng L^− 1 of PFOS and < 2.0-11 ng L^− 1 of PFPA were detected. And sewage effluents contained considerably higher concentrations of PFOS and PFOA.