氧化锌薄膜/锡掺杂玻璃光波导元件及其对氯苯的气敏性研究

建立了玻璃光波导气敏元件检测氯苯气体的方法.采用浸渍-提拉法将ZnO敏感膜固定在锡掺杂玻璃光波导表面,研制出了检测氯苯气体的ZnO薄膜/锡掺杂玻璃光波导气敏元件,并用该玻璃光波导气敏元件对挥发性有机气体进行了检测.实验结果表明,在室温下,气敏元件对氯苯气体有明显的响应,而对相同浓度的其它挥发性有机气体的响应相对较小,对...     

Y2O3薄膜/锡掺杂玻璃光波导气敏元件及其气敏性

采用溶胶-凝胶法将氧化钇(Y2O3)敏感膜固定在锡掺杂玻璃光波导表面,研制出了Y2O3薄膜/锡掺杂玻璃光波导气敏元件,并对挥发性有机气体进行了检测.通过XRD测试对敏感薄膜的结构及晶粒尺寸进行了表征.实验结果表明,在室温下Y2O3薄膜/锡掺杂玻璃光波导气敏元件对二甲苯、氯苯气体有较好的选择性响应,其响应浓度范围为l×10-3 ～1×10-5(V/V).Y2O3薄膜/锡掺杂玻璃光波导气敏元件具有灵敏度高、成本低、响应速度快、制作工艺简单和可逆性好等优点.     

热处理对LiFe1-0.01xY0.005xAg0.005xPO4薄膜光波导传感元件气敏性的影响

以FeSO4.7H2O,H3PO4,LiOH.H2O,AgNO3及Y(NO3)3.6H2O为原料,利用水热法一步合成出了LiFe1-0.01xY0.005xAg0.005xPO4粉体(x=0.5,1.0),并将该材料作为敏感试剂,用旋转-甩涂法做成纳米薄膜固定在锡掺杂玻璃光波导表面,在不同温度下进行热处理。采用紫外-可见分光光度计、测厚仪以及自组装的玻璃光波导气敏测试仪研究了热处理对LiFe1-0.01xY0.005xAg0.005xPO4薄膜光学及气敏特性的影响。研究结果表明:在450℃下进行热处理的薄膜元件具有良好的光学透明及较好的气敏特性。相同浓度的不同挥发性有机气体中,该传感元件对二甲苯气体有很好的选择性响应,其检测响应范围为1×10-7～1×10-3(V/V),响应-恢复时间分别小于5和100 s。     

PVA薄膜光波导气敏元件及其应用研究

将纯聚乙烯醇(PVA)和掺有维生素C的PVA作为敏感试剂,通过旋转甩涂法分别研制出了PVA薄膜/锡掺杂玻璃光波导元件和VC-PVA薄膜/锡掺杂玻璃光波导元件并检测其气敏特性.实验结果表明,PVA薄膜/锡掺杂玻璃光波导元件对二甲苯气体有良好的选择性响应,其响应浓度范围为10-4～10-7(体积比);加入VC后,使此敏感元...     

LiFe_(1-0.01x)Ni_(0.01x)PO_4薄膜干燥温度对其光学性质及气敏性的影响

将水热合成的Li Fe1-0.01xNi0.01xPO4(x=0.5,1.0)粉体作为敏感试剂,用旋转-甩涂法涂于锡掺杂玻璃光波导表面,在不同温度下进行热处理。采用紫外-可见分光光度计,测厚仪和平面玻璃光波导气敏测试系统(自组装)研究了薄膜干燥温度对Li Fe1-0.01xNi0.01xPO4薄膜光学及气敏特性的影响。研究结果表明,450℃下干燥的薄膜具有良好的光学透明性并对应的敏感元件显出良好的气敏特性。相同浓度的不同挥发性有机气体中,Li Fe0.99Ni0.01PO4传感元件对二甲苯气体有较大的响应,其检测响应范围为1×10-7~1×10-3(V/V0),响应-恢复时间分别小于5s和70s。     

氧化镍-铁酸锌复合薄膜/锡掺杂玻璃光波导传感元件的制备及其对硫化氢气体的气敏性

用溶胶-凝胶法制成了NiO掺杂的ZnFe2O4溶胶,并用浸渍提拉法将其固定在锡掺杂玻璃光波导表面,研制了NiO-ZnFe2O4复合薄膜/锡掺杂玻璃光波导气敏元件,并对无机有毒气体进行了检测。 实验结果表明,在室温下,该传感元件对H2S气体具有一定的选择性响应,而对相同浓度的其它无机气体的响应相对较小,能够检测到1.0×10-9（体积比）的H2S气体,其响应和恢复时间分别是6和8 s。 该元件具有灵敏度高、响应-恢复快、可逆性和重复性好、容易制备,在室温下便于操作等特点。     

LiFe0.98 Pt0.02 PO4薄膜的光学及气敏性研究

为提高LiFePO_4敏感薄膜元件的灵敏度,以铂(Pt)作为掺杂元素,用水热法一步合成出LiFe_(0.98)Pt_(0.02)PO_4粉末;利用旋涂法将其固定在锡掺杂玻璃光波导表面,制备了LiFe_(0.98)Pt_(0.02)PO_4薄膜/锡掺杂玻璃光波导元件。将敏感薄膜在不同温度下热处理,通过比较各个敏感薄膜元件对苯类挥发性有机气体的响应讨论薄膜处理温度对LiFe_(0.98)Pt_(0.02)PO_4薄膜元件光学特性及气敏性的影响。结果显示,在450℃下处理的薄膜因具有光学透明性好、折射率高、光传播损失小等特点对苯类气体显出较大的响应,能够检测出浓度为1×10~(-7)~1×10~(-3)V/V_0的二甲苯气体。当气体浓度小于1×10~(-6)V/V_0时,其他苯类气体不会对二甲苯的检测产生影响。     

钇掺杂对磷酸亚铁锂薄膜光波导传感元件气敏特性的影响

利用水热法合成出LiFePO4和钇(Y)掺杂的LiFePO4粉体,并作为敏感试剂,用浸渍-提拉法固定在锡掺杂玻璃光波导表面,分别研制了LiFePO4和LiFe0.99 Y0.01 PO4薄膜/锡掺杂玻璃光波导传感元件.用这些薄膜传感元件对挥发性有机气体进行检测,并比较了它们的气敏特性.结果表明,掺杂Y后LiFePO4薄...     

偶氮苯-PVP复合薄膜光波导传感器检测苯乙烯

将掺杂偶氮苯（Azo）的聚乙烯吡咯烷酮（PVP）作为敏感试剂,利用旋转甩涂法将其固定在钾离子（K⁺）交换玻璃光波导表面,研制了Azo-PVP复合薄膜/K⁺交换玻璃光波导气敏元件,并对其气敏特性进行研究。实验结果表明,该敏感元件对苯乙烯蒸汽有较好的选择性响应,其最低检测浓度为1.0×10^-8体积比（V/V₀）,响应-恢复时间分别为9 s和24 s。在浓度1.0×10^-81.0×10^-3（V/V₀）范围内,气体浓度与输出光强度之间有较好的线性关系。     

TiO2薄膜/锡掺杂玻璃光波导元件对苯乙烯蒸气的气敏性研究

本文将溶胶-凝胶法制备的溶胶采用浸渍提拉法固定在锡掺杂玻璃光波导元件表面,通过500℃热处理得到TiO2薄膜,且对低浓度的苯乙烯蒸气进行检测。从实验得知,该传感元件在挥发性有机气体浓度(体积分数)低到5.0×10-5时只对苯乙烯有响应,此时其他气体毫无响应,并在1.0×10-6～5.0×10-4范围之内对苯乙烯有较好的响应。响应时间和恢复时间分别为12s和34s。该传感器具有灵敏度高、响应快、可逆性和重复性好、易制作等特点。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.