Development of an Ion-Pair HPLC Method for Determination of Acebutolol in Pharmaceuticals

A simple and accurate ion-pair reversed-phase high-performance liquid chromatographic (RP-HPLC) method has been developed and validated for determination of acebutolol (ACE) in tablet dosage forms. Both ACE and ambroxol (internal standard) were well separated using a reversed phase column and a mobile phase consisting of a mixture of methanol-0.05 M acetic acid (containing 8 mM sodium 1-heptanesulfanate) (65:35 v/v) with pH adjusted to 3.2 with triethylamine. The mobile phase was pumped at 0.80 mL min^?1 flow rate and ACE was detected by diode-array detection at 240 nm. The retention times for ACE and internal standard (IS) were 4.574 and 8.236 min, respectively. A linear response (r = 0.9998) was observed in the range of 0.27–2.93 μg mL^?1 in mobile phase. The limit of detection and limit of quantification were found as 0.07 and 0.23 μg mL^?1 in the mobile phase. Validation parameters such as precision, accuracy, selectivity, reproducibility, and system suitability tests were also determined. The excipients did not interfere with the assay of ACE in tablet dosage forms. It is suggested that the proposed method can be used for routine quality control and dosage-form assay of ACE.     

Determination of Boanmycin in Pharmaceutical Preparations by a Simple and Rapid Ion-pair LC Method

An ion-pair HPLC method with UV detection is described for the determination of boanmycin in freeze-dried pharmaceutical preparations. Chromatographic separation was achieved on a 5 μm Agilent Eclipse XDB-C₁₈ column (150 × 4.6 mm). The mobile phase contained methanol, acetonitrile, 055 M sodium hexanesulfonate and 0.08 M acetic acid in water. UV detection was at 291 nm. The assay was validated over a linear concentration range from 0.05 to 120 μg mL^?1. The method was applied to determine the content of BAM in freeze-dried powders.     

High Performance Liquid Chromatographic Separation and Quantitative Analysis of Ginsenosides Using a Polyvinyl Alcohol-Bonded Stationary Phase

A simple high performance liquid chromatographic assay for the simultaneous quantitative analysis of seven ginsenosides, Rb1, Rb2, Rc, Rd, Re, Rf and Rg1 in commercial ginseng products is described. Chromatographic separation of the analytes was achieved in less than 20 min using a polyvinyl alcohol-bonded column with UV detection at 203 nm. Optimization of chromatographic conditions was determined by a three-factor central composite design, the variables being the percentage of acetonitrile in the mobile phase, column temperature and flow rate. A full quadratic model was found to be adequate in describing the separation of ginsenosides on the polyvinyl alcohol-bonded stationary phase. Complete separation of seven ginsenosides was achieved using acetonitrile–water (82.5/17.5) as the mobile phase run isocratically at a flow rate of 298 μL min^?1 and with the column temperature at 9 °C. The developed method was validated over the range of 10–120 μg mL^?1 using a 5 μL sample injection volume. Intra- and inter-day variation for three ginsenoside standards (Rf, Rd and Rb1) at three concentration levels ranged from 0.07 to 0.83% expressed as the relative standard deviation. The accuracy based on the nominal concentration values at three concentration levels was in the range 98.7–100.8%. The limit of detection was between 0.43 and 1.03 μg mL^?1 while the limit of quantification was from 1.42 to 3.13 μg mL^?1. The method is found to be applicable for the determination of ginsenosides in commercial ginseng products.     

Quantitative LC Analysis of Cyclosporine A in Ocular Samples

An isocratic reversed-phase HPLC method with ultraviolet detection at 205 nm has been developed for analysis of cyclosporine A (CyA) in rabbit ocular samples. Neither internal standard nor extraction was needed for sample preparation. Acetonitrile (ACN; 1 mL) was added to 250 μL aqueous and vitreous samples to precipitate proteins. The supernatant was dried and the residue was reconstituted in mobile phase and injected for HPLC analysis. Chromatography was performed on an octadecyl silane-A (ODSA) C₁₈ (4.6 × 250 mm, 5 μm) column. The column temperature was fixed at 70 °C and the mobile phase was ACN 65%, methanol 20% and water 15% at a flow rate of 1.5 mL min^?1. The calibration curve for CyA in rabbit ocular samples was linear over the concentration range 0.2 and 10 μg mL^?1 with a correlation coefficient of 0.9992. Intra-day and inter-day precision were 4.61–7.83% and 5.27–10.70%, respectively. Intra-day and inter-day accuracy were 89.2–108% and 83.4–111%, respectively. The limits of detection (LOD) and quantification (LOQ) were 5.7 and 38 ng mL^?1, respectively. The method was successfully used for analysis of CyA in real aqueous and vitreous humor samples from New Zealand albino rabbits. The method is therefore suitable for analysis of CyA in ocular samples.     

LC Determination of Clindamycin Phosphate from Chitosan Microspheres

A simple, rapid and precise reverse phase LC method was adopted, modified and validated for the determination of clindamycin phosphate from chitosan microspheres prepared by spray drying method. Separation was performed using ACE5 C18 reversed phase column (150 mm × 4.6 mm, 5 μm) with acetonitrile:phosphate buffer at pH 2.5 (25:75 v/v) as mobile phase. The limit of detection was 46.43 × 10^?3 μg mL^?1, with UV detection at 210 nm. No interference from chitosan and other excipients was observed. Therefore an incorporation efficiency of microspheres could be determined accurately and specifically.     

Simultaneous Determination of Dextromethorphan Hydrobromide, Pyrilamine Maleate and Sodium Benzoate in a Cough Cold Syrup by LC

A liquid chromatographic method for the simultaneous determination of dextromethorphan hydrobromide, pyrilamine maleate and sodium benzoate in cough cold syrup has been developed. The method was based on replacing heptane sulfonate by sodium chloride as ion pairing agent. The addition of sodium chloride to the mobile phase has changed the retention behaviour of the basic drugs. The separation of these compounds was achieved in less than 8 min with an isocratic mobile phase consisting of acetonitrile/0.1 M dihydrogenphosphate buffer containing 0.1 M sodium chloride (29:71 v/v) at pH 2.5 and using a Kromasil C18 column. The analysis was performed at a flow rate of 1 mL min^?1 and at a detection wavelength of 220 nm. The selectivity, linearity of calibration, accuracy, within and between days precision, limit of detection and quantification, recovery were examined as parts of the method validation. Calibration curves were linear in the range 1–140 μg mL^?1 with a regression coefficient (R ²) better than 0.999. The results of the method repeatability (intra-day) and reproducibility (inter-day) were all less than 2% (n = 6). The lowest detectable concentration of dextromethorphan hydrobromide and pyrilamine maleate varied between 0.10 and 0.12 μg mL^?1. The proposed liquid chromatographic method was satisfactorily applied for the routine quality control of dextromethorphan hydrobromide, pyrilamine maleate and sodium benzoate in cough cold syrup formulations.     

Determination of Atenolol in Human Plasma by Pseudo Reversed Phase Liquid Chromatography-Tandem Mass Spectrometry

Previous HPLC determination of atenolol on reversed-phase packings has often required a mobile phase containing three components: organic modifier, buffer and ion-pairing reagent or organic amine. In addition to the complexity of the eluents employed, alkyl sulphonates and organic amines in the mobile phase can reduce the life of silica-based bonded columns. A new simple, rapid and sensitive method—pseudo reversed-phase liquid chromatography/tandem mass spectrometry has been developed for the analysis of atenolol in human plasma using bare silica as the stationary phase coupled with a simple mobile phase consisted of 5% acetonitrile and 95% formate buffer. The optimization of separation is fast and easy. The assay was validated for the concentration range 1–100 ng mL^?1 with a detection limit of 1 ng mL^?1. Moreover, the silica column was durable with the mainly aqueous eluents. No obvious loss in performance was observed for 30,000 column volumes of eluent.     

Establishment of a Fingerprint of Raspberries by LC

To monitor the quality of raspberries, a simple, practicable, and feasible method, high-performance liquid chromatography coupled with photodiode-array detection, has been developed both for fingerprinting analysis and for quantitative analysis of hyperoside and tiliroside. Compounds were separated on a 4.6 mm × 250 mm, 5-μm particle, C₁₈ column with a mobile phase gradient prepared from acetonitrile and 0.5% (v/v) aqueous glacial acetic acid. The mobile phase flow rate was 1.0 mL min^?1, the temperature 30 °C, the injection volume 10 μL, and the detection wavelength 340 nm. Under the optimum conditions the two compounds could be well separated with good linear relationships between response and amount in the range 0.024–2.380 μg for hyperoside and 0.026–2.570 μg for tiliroside. Recovery of hyperoside and tiliroside was 99.3 and 106.0%, respectively. The standardized chromatographic fingerprint and the similarity of samples were calculated by use of software. Principal-components analysis was used to differentiate and classify 14 samples on the basis of the area of seven common peaks. Combination of chemical fingerprinting and the quantitative method with principal-component analysis may provide a firm basis for further research on quality control of raspberries.     

整体柱离子对色谱-间接紫外检测法快速测定N-甲基,丙基吗啉阳离子

建立了快速分析无紫外吸收的N-甲基,丙基吗啉阳离子的离子对色谱-间接紫外检测法。采用反相C18硅胶整体柱,以背景紫外吸收试剂-离子对试剂-有机溶剂为流动相。研究了背景紫外吸收试剂、检测波长、离子对试剂、有机溶剂、柱温、流速对吗啉阳离子测定的影响。最佳色谱条件为:(0.5 mmol/L对氨基苯酚盐酸盐-0.1 mmol/L庚烷磺酸钠)溶液-甲醇(9:1, v/v)为流动相,检测波长230 nm,柱温30 ℃,流速1.0 mL/min。在此条件下,N-甲基,丙基吗啉阳离子的保留时间为2.966 min,检出限为0.07 mg/L(S/N=3),峰面积的相对标准偏差为2.1%(n=5),保留时间的相对标准偏差为0.02%(n=5)。将此方法用于分析实验室合成的N-甲基,丙基吗啉离子液体,加标回收率为98.8%。结果表明本方法简便、快速。     

Amperometric sensor based on carbon nanotubes and electropolymerized vanillic acid for simultaneous determination of ascorbic acid,dopamine, and uric acid

This paper describes the development of a simple and efficient nanostructured platform based on multi-walled carbon nanotubes (MWCNT) functionalized with an in situ generated vanillic acid (VA) polymer. It was used as an analytical sensor for the simultaneous determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). The electropolymerization process of VA, performed on MWCNT-modified glassy carbon electrode, produces three redox systems based on quinone/hydroquinone functionality, as observed by cyclic voltammetry. The amperometric sensor has as figures of merit for the simultaneous determination of AA, DA, and UA the following values: for AA, a linear range of 5–120 μM and detection limit of 3.5 μM; for DA, a linear range of 5–120 μM and detection limit of 4.5 μM; and for UA, a linear range of 5–120 μM and a detection limit of 1.5 μM. From the obtained performance, the development of the platform based on MWCNT/poly-VA is justified for the simultaneous determination of AA, DA, and UA.     

Determination of Nitric Oxide-Derived Nitrite and Nitrate in Biological Samples by HPLC Coupled to Nitrite Oxidation

Nitrite and nitrate are main stable products of nitric oxide, a pivotal cellular signaling molecule, in biological fluids. Therefore, accurate measurement of the two ions is profoundly important. Nitrite is difficult to be determined for a larger number of interferences and unstable in the presence of oxygen. In this paper, a simple, cost-effective and accurate HPLC method for the determination of nitrite and nitrate was developed. On the basis of the reaction that nitrite is oxidized rapidly to nitrate with the addition of acidic potassium permanganate, the determination of nitrite and nitrate was achieved by the following strategy: each sample was injected twice for HPLC analysis, i.e. the first injection was to measure nitrate, and the second injection was to measure total nitrate including initial nitrate and the nitrate from the conversion of nitrite with the addition of acid potassium permanganate in the sample. The amount of nitrite can be calculated as difference between injections 2 and 1. The HPLC separation was performed on a reversed phase C₁₈ column for 15 min. The mobile phase consisted of methanol–water (2:98 by volume); the water in the mobile phase contained 0.60 mM phosphate salt (potassium dihydrogen and disodium hydrogen phosphate) and 2.5 mM tetrabutylammonium perchlorate (TBAP). The UV wavelength was set at 210 nm. Additionally, we systemically investigated the effects of the concentration of phosphate salt and TBAP in the mobile phase, the pH of the mobile phase, and the amount of acidic potassium permanganate added to the sample on the separation efficacy. The results showed that the limits of detection (LOD) and the limit of quantitation (LOQ) were 0.075 and 0.25 μM for nitrate (containing the oxidized nitrite), respectively. The linear range was 1–800 μM. This developed approach was successfully applied to assay nitrite/nitrate levels in cell culture medium, cell lysate, rat plasma and urine.

     

Assay of Kanamycin A by HPLC with Direct UV Detection

The development of a simple reversed phase ion pair liquid chromatographic method for the assay of kanamycin A has been described. Because of the lack of a UV chromophore in the structure of kanamycin A, borate complexation was used to allow direct UV detection at 205 nm. Three columns were evaluated in this study: Zorbax Extend C18 (4.6 mm × 250 mm; 5 μm), XBridge C18 (4.6 mm × 250 mm; 5 μm) and apHera C18 (4.6 mm × 250 mm; 5 μm). The mobile phase was a mixture of 0.1 M disodium tetraborate (pH 9.0) and water (20:80, v/v) supplemented with 0.5 g L^?1 sodium octanesulphonate. Final chromatographic conditions were achieved on the XBridge column at 50 °C. The method was validated according to ICH guidelines and applied to a commercially available sample. It is much faster and more specific than the current microbiological assay prescribed in the European Pharmacopoeia. No expensive equipment is necessary to perform this assay making it a viable replacement.     

Assay of Kanamycin A by HPLC with Direct UV Detection

The development of a simple reversed phase ion pair liquid chromatographic method for the assay of kanamycin A has been described. Because of the lack of a UV chromophore in the structure of kanamycin A, borate complexation was used to allow direct UV detection at 205 nm. Three columns were evaluated in this study: Zorbax Extend C18 (4.6 mm × 250 mm; 5 μm), XBridge C18 (4.6 mm × 250 mm; 5 μm) and apHera C18 (4.6 mm × 250 mm; 5 μm). The mobile phase was a mixture of 0.1 M disodium tetraborate (pH 9.0) and water (20:80, v/v) supplemented with 0.5 g L⁻¹ sodium octanesulphonate. Final chromatographic conditions were achieved on the XBridge column at 50 °C. The method was validated according to ICH guidelines and applied to a commercially available sample. It is much faster and more specific than the current microbiological assay prescribed in the European Pharmacopoeia. No expensive equipment is necessary to perform this assay making it a viable replacement.

     

Amperometric Determination of Cholesterol-Reducing Drug,Ezetimibe, Using Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotubes and Sodium Dodecylsulfate

A simple and sensitive electrochemical method is described for the determination of the cholesterol-reducing drug ezetimibe in aqueous solution. A glassy carbon electrode, modified with multiwalled carbon nanotubes and sodium dodecylsulphate was used as the working electrode. Ezetimibe yields a well-defined anodic peak at the surface of the electrode in an aqueous solution of pH 13. A linear amperometric calibration curve was obtained in the range of 1.2–78 μM (0.5–32.0 μg/mL) of ezetimibe, with a sensitivity of 88.6 nA/μM and a detection limit of 300 nM (0.12 μg/mL). The sensor was applied successfully to the determination of ezetimibe in pharmaceutical preparations.     

Determination of 2,6-di-tert-butylphenol in Irganox 1425

An ion suppression reversed phase high performance liquid chromatography method has been developed for the determination of 2,6-di-tert-butylphenol in Irganox 1425. Separation was carried out on a Welch Material Ultimate XB-C₁₈ column (5 μm, 150 mm × 4.6 mm), using methanol–water (0.1 % HClO₄) (75/25, v/v) mixture as the mobile phase in an isocratic elution. Detection was performed by UV absorption at a wavelength of 275 nm, and the limit of detection was 0.2 μg/mL. The method presented excellent repeatability and precision with both intra- and inter-day relative standard deviations (RSDs) of less than 2.0 %, as well as satisfactory accuracy with the recovery of 98.7–102.3 %, and therefore can be applied for the quality control analysis of Irganox 1425 industrial product.     

Development of a Validated Stability-Indicating LC Assay and Stress Degradation Studies of Linezolid in Tablets

This paper describes the validation of an isocratic LC method for the assay of linezolid in tablets. Validation parameters such as linearity, precision, accuracy, specificity, limit of detection, limit of quantitation and robustness were determined. LC was carried out by reversed phase technique on an RP-18 column with a mobile phase composed of 1% acetic acid:methanol:acetonitrile (50:25:25, v/v/v). Linezolid and your combination drug product were exposed to acid, base, oxidation, dry heat and photolytic stress conditions. A linear response (r > 0.9999) was observed in the range of 8.0–20.0 μg mL⁻¹. The retention time of linezolid was 4.6 min. The method showed good recoveries and intra- and inter-day relative standard deviations were less than 1.0%. The LOD and LOQ were 0.21 and 0.63 μg mL⁻¹, respectively. The developed LC method for determination of related substances and assay determination of linezolid can be used to evaluate the quality of regular production samples. It can also be used to test the stability samples of linezolid.

     

Determination of Nitric Oxide-Derived Nitrite and Nitrate in Biological Samples by HPLC Coupled to Nitrite Oxidation

Nitrite and nitrate are main stable products of nitric oxide, a pivotal cellular signaling molecule, in biological fluids. Therefore, accurate measurement of the two ions is profoundly important. Nitrite is difficult to be determined for a larger number of interferences and unstable in the presence of oxygen. In this paper, a simple, cost-effective and accurate HPLC method for the determination of nitrite and nitrate was developed. On the basis of the reaction that nitrite is oxidized rapidly to nitrate with the addition of acidic potassium permanganate, the determination of nitrite and nitrate was achieved by the following strategy: each sample was injected twice for HPLC analysis, i.e. the first injection was to measure nitrate, and the second injection was to measure total nitrate including initial nitrate and the nitrate from the conversion of nitrite with the addition of acid potassium permanganate in the sample. The amount of nitrite can be calculated as difference between injections 2 and 1. The HPLC separation was performed on a reversed phase C₁₈ column for 15 min. The mobile phase consisted of methanol–water (2:98 by volume); the water in the mobile phase contained 0.60 mM phosphate salt (potassium dihydrogen and disodium hydrogen phosphate) and 2.5 mM tetrabutylammonium perchlorate (TBAP). The UV wavelength was set at 210 nm. Additionally, we systemically investigated the effects of the concentration of phosphate salt and TBAP in the mobile phase, the pH of the mobile phase, and the amount of acidic potassium permanganate added to the sample on the separation efficacy. The results showed that the limits of detection (LOD) and the limit of quantitation (LOQ) were 0.075 and 0.25 μM for nitrate (containing the oxidized nitrite), respectively. The linear range was 1–800 μM. This developed approach was successfully applied to assay nitrite/nitrate levels in cell culture medium, cell lysate, rat plasma and urine.     

Simultaneous Determination of Artesunate and Amodiaquine in Fixed-Dose Combination by a RP-HPLC Method with Double UV Detection: Implementation in Interlaboratory Study Involving Seven African National Quality Control Laboratories

The fixed-dose combination artesunate (AS)–amodiaquine (AQ) is one of the most widely used treatments for uncomplicated falciparum malaria. It is currently proposed to the inclusion in the model list of essential medicines of World Health Organization and has been recently prequalified. Until now, no satisfactory method for the simultaneous determination of the two active ingredients had been available. Thus, a reversed phase high performance liquid chromatography for the quantitative determination of AQ and AS was developed and validated. Chromatography was performed using an end-capped octadecylsilyl silica gel column (100 × 4.6 mm, 3 μm) with a binary gradient using aqueous phase containing potassium dihydrogen phosphate (10 mM) and acetonitrile. Taking into consideration the physico-chemical characteristics of the two compounds related to their ionization, the use of a counter ion was necessary to ensure the retention of AQ in a reversed phase system simultaneously to AS. Thus, aqueous mobile phase was adjusted to pH 3.0 and the chosen counter ion was sodium 1-octanesulfonate (100 mM). In these conditions, the retention times were about 4 min for AQ and 10 min for AS with UV detection at 300 and 210 nm, respectively. Method was then validated according to ICH guideline (specificity/linearity/accuracy/precision) and potential interferences with excipients and degradation products were checked. It has also been used for an interlaboratory study involving seven African National Quality Control Laboratories and Afssaps (Agence française de sécurité sanitaire des produits de santé) laboratory. The results demonstrate that this rapid and simple method can be easily used by official laboratories for routine control, market survey and for the detection of potential substandard medicines which are very frequent in African countries.

     

A validated method for analysis of chromium picolinate in nutraceuticals by reversed phase high performance liquid chromatography

A validated high performance liquid chromatographic method was developed for the determination of chromium picolinate in pharmaceutical dosage forms. The analysis was performed at room temperature using a reversed-phase Supelcosil LC-18 (250 x 4.6 mm, 5 microm) column. The mobile phase consisted of acetonitrile:water (40:60 v/v) at a fl ow rate of 0.8 mL/min. The UV-detector was set at 264 nm. The developed method showed a good linear relationship in the concentration range from 0.125 to 12.5 microg/mL with a correlation coefficient from 0.999. The limit of detection and limit of quanti fi cation were 0.091 and 0.181 microg/mL, respectively.     

Amperometric Phenol Biosensor Based on Horseradish Peroxidase Entrapped PVF and PPy Composite Film Coated GC Electrode

Polyvinylferrocene (PVF) was used as a mediator for the fabrication of a horseradish peroxidase (HRP)-modified electrode to detect phenol derivatives via a composite polymeric matrix of conducting polypyrrole (PPy). Through an electropolymerization process, enzyme HRP was entrapped with PPy in a three-electrode system onto a glassy carbon electrode previously covered with PVF, resulting in a composite polymeric matrix. Steady-state amperometric measurements were performed at ?200 mV vs. Ag/AgCl in aqueous phosphate buffer containing NaCl 0.1 M (pH 6.8) in the presence of hydrogen peroxide. The response of the HRP-modified PVF electrode was investigated for various phenol derivatives, which were 4-chlorophenol, phenol, catechol, hydroquinone, 2-aminophenol, pyrogallol, m-cresol, and 4-methoxyphenol. Analytical parameters for the fabricated PVF electrode were obtained from the calibration curves. The highest sensitivity was obtained from the calibration of 4-chlorophenol as 29.91 nA/μM. The lowest detection limit was found to be 0.22 μM (S/N?=?3) for catechol, and the highest detection limit was found to be 0.79 μM (S/N?=?3) for 4-methoxyphenol among the tested derivatives. The biosensor can reach 95% of steady-state current in about 5 min. The electrode is stable for 2 months at 4 °C.