Photovoltage improvements and recombination suppression by montmorillonite addition to PEO gel electrolyte for dye-sensitized solar cells

Montmorillonite (MMT) added to electrolytes has been reported in the literature to facilitate the transport of I(-)/I(3)(-), and improve the ionic conductivity and consequent photocurrent of dye-sensitized solar cells (DSCs). This paper firstly observes, investigates and reports that MMT addition to a poly(ethylene oxide) (PEO)-based gel electrolyte not only improves the ionic conductivity of the gel electrolyte, but also increases the photovoltage and decreases the dark current. From the results of electrochemical impedance spectroscopy (EIS) and transient photovoltage spectra, we evidence that MMT in the polymer gel electrolyte can efficiently retard the charge recombination that occurs at the TiO(2)/dye/electrolyte interfaces.     

菁类染料敏化的固态纳米TiO2光电化学电池

染料敏化TiO2光电化学电池具有较高的能量转换效率,价格仅为传统单晶硅太阳能电池的1／10,成为半导体光电化学领域的研究热点^[1-4]。但该类电池内的电解液可流动,造成电池密封困难,限制其实用化。针对这一问题,采用无机p-型半导体材料^[5,6]和高分子导体等电解液替代物组装固态光电化学电池成为该领域的新的研究方向^[7-9]。我们^[10]用凝胶网络高分子电解质组装成固态电池,取得了令人满意的结果。电池中原使用的敏化剂是顺二硫氰根－双（2,2′－联吡啶－4,4′－二羧酸）合钌（Ⅱ）(cis-bis)(thiocyanato)bis(2,2′-bipyridyl-4,4′-dicarboxylate)ruthenium(Ⅱ）,其价格昂贵,合成路线复杂。本文用自合成的、价格低廉的纯有机不对称菁类染料（Cyanine dye,以下简称为CD）敏化TiO2电极和基于聚氧乙烯（PEO）的凝胶网络高分子电解质组装成固态电池,并研究了所得固态电池的光电转换性能。     

Significant efficiency improvement of the black dye-sensitized solar cell through protonation of TiO2 films

This paper describes the influence of acid pretreatment ofTiO2 mesoporous films prior to dye sensitization on the performance of dye-sensitized solar cells based on [(C4H9)4N]3[Ru(Htcterpy)(NCS)3] (tcterpy = 4,4',4"-tricarboxy- 2,2',2"-terpyridine), the so-called black dye. The HCl pretreatment caused an increase in overall efficiency by 8%, with a major contribution from photocurrent improvement. It is speculated, from the analysis of incident photon-to-electron conversion efficiency, UV-vis absorption spectra, redox properties of the dye and TiO2, and the impedance spectra of the dye-sensitized solar cells, that photocurrent enhancement is attributed to the increases in electron injection and/or charge collection efficiency besides the improvement of light harvesting efficiency upon HCl pretreatment. Open-circuit photovoltage (V(oc)) remained almost unchanged in the case of significant positive shift of flat band potential for TiO2 upon HCl pretreatment. The suppression of electron transfer from conduction band electrons to the I3- ions in the electrolyte upon HCl pretreatment, reflected by the increased resistance at the TiO2/dye/electrolyte interface and reduced dark current, resulted in a V(oc) gain, which compensated the V(oc) loss due to the positive shift of the flat band. Using the HCl pretreatment approach, 10.5% of overall efficiency with the black dye was obtained under illumination of simulated AM 1.5 solar light (100 mW cm(-2)) using an antireflection film on the cell surface.     

High efficiency dye-sensitized nanocrystalline solar cells based on ionic liquid polymer gel electrolyte

An ionic liquid polymer gel containing 1-methyl-3-propylimidazolium iodide (MPII) and poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) has been employed as quasi-solid-state electrolyte in dye-sensitized nanocrystalline TiO2 solar cells with an overall conversion efficiency of 5.3% at AM 1.5 illumination.     

Sensitizer molecular structure-device efficiency relationship in dye sensitized solar cells

In the Dye Sensitized Solar Cell (DSSC) the dye sensitizer carries out the light harvesting function and is therefore crucial in determining overall cell efficiency. In addition, the dye sensitizer can influence many of the key electron transfer processes occurring at the TiO(2)/dye/electrolyte interface which also determine efficiency. Dye structure can influence and drive forward electron injection into the conduction band of the TiO(2). Conversely, dye structure can help retard loss electron transfer processes such as charge recombination of injected electrons in the TiO(2) with dye cations and also recombination of these electrons with the electrolyte. Therefore tuning dye sensitizer light absorbing properties and control of the aforementioned electron transfer processes through structural design of the dye sensitizer is an important avenue through which optimization of DSSC efficiency should be pursued. In this critical review the latest work focusing on the design of dyes for efficient DSSCs is revised (111 references).     

Dye-sensitized solar cells based on multiwalled carbon nanotube-titania/titania bilayer structure photoelectrode

Dye-sensitized solar cells (DSSCs) were fabricated using multiwalled carbon nanotube (MWCNT)-TiO(2) nanocomposite as a light scattering layer. Morphology of the MWCNT-TiO(2) film was investigated by field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). FESEM and TEM images demonstrate that MWCNTs and TiO(2) nanoparticles can be dispersed with chitosan. Internal resistance in the DSSC was characterized by electrochemical impedance spectroscopy (EIS). EIS results reveal a decrease in the charge resistance of electrolyte/dye/MWCNT-TiO(2)/TiO(2) interface with increasing MWCNT content up to 3 wt% which leads to an improvement in the photovoltaic performance. Compare with a nanocrystalline TiO(2) single-layer cell, the DSSC based on the MWCNT (3 wt%)-TiO(2)/TiO(2) bilayer structure photoelectrode shows ~100% increase in solar-to-electric energy conversion efficiency, which is attributed to the inclusion of MWCNTs in TiO(2) matrix.     

Enhancing the device performance of Sb2S3-sensitized heterojunction solar cells by embedding Au nanoparticles in the hole-conducting polymer layer

Performance of Sb(2)S(3)-sensitized heterojunction solar cells is enhanced by embedding Au nanoparticles in the poly-3-hexylthiophene (P3HT) hole-conducting polymer layer. The improved charge transfer/transport at the Sb(2)S(3)/P3HT/Au interface by extended interface area of the P3HT/Au counter electrode and the re-absorption of the backscattering light from the embedded Au nanoparticles enhanced the device performance: J(sc) 11.0 to 12.8 mA cm(-2), V(oc) 606 to 626 mV, fill factor (FF) 60.5 to 61.2%, and power conversion efficiency (η) 4.0 to 4.9%. Simultaneous enhancement of V(oc), J(sc), and FF in Au nanoparticle-embedded systems is mainly attributed to the improved charge collection efficiency and light harvesting efficiency of Sb(2)S(3) due to the improved charge transfer/transport in the Sb(2)S(3)/P3HT/Au interface.     

Effect of 15-crown-5 on the charge transfer resistance at the polymer electrolyte/modified Li-electrode interface

The effect of 15-crown-5, which is applied immediately to pure and modified surface of a lithium electrode, on the charge transfer resistance at the electrode/polymer electrolyte interface is studied. The polymer electrolyte consists of a 1: 1 mixture of oligourethan dimethacrylate and polypropylene glycol monomethacrylate (20 wt %), an initiator (azobisisobutyronitrile) (2 wt %), and a 1 M LiClO₄ solution in gamma-butyrolactone (78 wt %). The conductivity of this gel electrolyte is 3 × 10^?3 S cm^?1. The temperature dependence of the impedance of the Li/gel electrolyte/Li electrochemical cells is measured for electrodes of four types. The activation energies for the charge transfer at the Li/electrolyte interface are calculated. It is found that, after treating the test lithium electrodes with 15-crown-5, the charge transfer resistance decreases, and in the case of the modified lithium surface, the activation energy for the process decreases by 1.8 times.     

基于偏氟乙烯-六氟丙烯共聚物凝胶电解质的染料敏化太阳电池光电性能研究

采用偏氟乙烯-六氟丙烯共聚物[P(VDF-HFP)]胶凝3-甲氧基丙腈基液体电解质, 成功制备了凝胶电解质并组装成准固态染料敏化太阳电池. 差示扫描量热测试结果表明凝胶电解质的溶液-凝胶转变温度(TSG)为71 ℃. 利用电化学方法分析了凝胶电解质中 电对的表观扩散系数及电导率低于液体电解质的原因, 同时结合暗态伏安法考察了电池内部TiO2多孔薄膜电极/电解质界面处的暗反应, 分析了凝胶化对电池光伏性能的影响. 进一步老化实验结果表明凝胶电池的稳定性明显优于液体电池.     

Preparation of a nanoporous CaCO3-coated TiO2 electrode and its application to a dye-sensitized solar cell

A nanoporous CaCO3 overlayer-coated TiO2 thick film was prepared by the topotactic thermal decomposition of Ca(OH)2, and its performance as an electrode of a dye-sensitized solar cell was investigated. As compared to bare TiO2, nanoporous CaCO3-coated TiO2 provided higher specific surface area and, subsequently, a larger amount of dye adsorption; this in turn increased short-circuit current (Jsc). Furthermore, the CaCO3 coating demonstrated increased impedance at the TiO2/dye/electrolyte interface and increased the lifetime of the photoelectrons, indicating the improved retardation of the back electron transfer, which increases Jsc, open-circuit voltage (Voc), and fill factor (ff). Thereby, the energy conversion efficiency (eta) of the solar cell improved from 7.8 to 9.7% (an improvement of 24.4%) as the nanoporous CaCO3 layer was coated onto TiO2 thick films.     

Comparing spiro-OMeTAD and P3HT hole conductors in efficient solid state dye-sensitized solar cells

Two hole conductor materials, spiro-OMeTAD and P3HT, were compared in solid-state dye-sensitized solar cells. Two organic dyes containing one anchor unit (D35) or two anchor units (M3) were used in the comparison. Absorbed photon to current conversion efficiency close to unity was obtained for the devices with spiro-OMeTAD. Energy conversion efficiencies of 4.7% and 4.9% were measured for the devices with spiro-OMeTAD and the dyes D35 and M3, respectively. For the devices using the P3HT hole conductor the results were rather different comparing the two dye molecules, with energy conversion efficiencies of 3.2% and 0.5% for D35 and M3, respectively. Photo-induced absorption measurements suggest that the regeneration of the dyes, and the polymer infiltration, is not complete using P3HT, while spiro-OMeTAD regenerates the dyes efficiently. However, the TiO(2)/D35/P3HT system shows rather high energy conversion efficiency and electrochemical oxidation of the dyes on TiO(2) indicates that D35 have a more efficient dye to dye hole conduction than M3, which thereby might explain the higher performance. The dye hole conduction may therefore be of significant importance for optimizing the energy conversion in such hybrid TiO(2)/dye/polymer systems.     

The effects of polymer gel electrolyte composition on performance of quasi-solid-state dye-sensitized solar cells

Polymer gel electrolytes based on poly(acrylic acid)-poly(ethylene glycol) (PAA–PEG) hybrid have been prepared and applied to developed quasi-solid-state dye-sensitized solar cells (DSCs). PAA–PEG hybrid was synthesized by polymerization reaction. Quasi-solid-state DSCs were fabricated with synthesized PAA–PEG electrolyte. The effects of alkali iodides LiI, KI, and I₂ concentrations on liquid electrolyte absorbency and ionic conductivity of PAA–PEG were investigated. The evolution of the solar cell parameters with polymer gel electrolyte compositions was revealed. DSCs based on PAA–PEG with optimized KI/I₂ concentrations showed better performances than those with optimized LiI/I₂ concentrations. The electrochemical impedance spectroscopy technique was employed to examine the electron lifetime in the TiO₂ electrode and quantify charge transfer resistances at the TiO₂/dye/electrolyte interface and the counter electrode in the solar cells based on the PAA–PEG hybrid gels. A maximum conversion efficiency of 4.96% was obtained for DSCs using KI based quasi-solid electrolyte under 100 mW cm⁻². Our work suggests that KI can be the promising alkali metal iodide for improving the performance of PAA–PEG hybrid gel DSCs.     

A 7.72% efficient dye sensitized solar cell based on novel necklace-like polymer gel electrolyte containing latent chemically cross-linked gel electrolyte precursors

Novel necklace-like polymer gel electrolytes containing latent chemically cross-linked gel electrolyte precursors were prepared for quasi-solid dye sensitized solar cells with a highest efficiency of 7.72% and an active area of 0.25 cm2 under AM1.5 condition at 100 mW cm(-2) irradiation.     

Modified phthalocyanines for efficient near-IR sensitization of nanostructured TiO(2) electrode

A zinc phthalocyanine with tyrosine substituents (ZnPcTyr), modified for efficient far-red/near-IR performance in dye-sensitized nanostructured TiO(2) solar cells, and its reference, glycine-substituted zinc phthalocyanine (ZnPcGly), were synthesized and characterized. The compounds were studied spectroscopically, electrochemically, and photoelectrochemically. Incorporating tyrosine groups into phthalocyanine makes the dye ethanol-soluble and reduces surface aggregation as a result of steric effects. The performance of a solar cell based on ZnPcTyr is much better than that based on ZnPcGly. Addition of 3alpha,7alpha-dihydroxy-5beta-cholic acid (cheno) and 4-tert-butylpyridine (TBP) to the dye solution when preparing a dye-sensitized TiO(2) electrode diminishes significantly the surface aggregation and, therefore, improves the performance of solar cells based on these phthalocyanines. The highest monochromatic incident photo-to-current conversion efficiency (IPCE) of approximately 24% at 690 nm and an overall conversion efficiency (eta) of 0.54% were achieved for a cell based on a ZnPcTyr-sensitized TiO(2) electrode. Addition of TBP in the electrolyte decreases the IPCE and eta considerably, although it increases the open-circuit photovoltage. Time-resolved transient absorption measurements of interfacial electron-transfer kinetics in a ZnPcTyr-sensitized nanostructured TiO(2) thin film show that electron injection from the excited state of the dye into the conduction band of TiO(2) is completed in approximately 500 fs and that more than half of the injected electrons recombines with the oxidized dye molecules in approximately 300 ps. In addition to surface aggregation, the very fast electron recombination is most likely responsible for the low performance of the solar cell based on ZnPcTyr.     

Effective enhancement of the performance of black dye based dye-sensitized solar cells by metal oxide surface modification of the TiO2 photoelectrode

Effective enhancement of the performance of black dye based dye-sensitized solar cells has been achieved by MgO or Al(2)O(3) surface modification of the TiO(2) photoelectrode. The conversion efficiency was improved from 10.4% to 10.8% due to the blocking effect of the thin overlayer at the TiO(2) surface.     

Electrical,optical and photoelectrochemical studies on a solid PEO-polymer electrolyte doped with low viscosity ionic liquid

Solid polymer electrolyte (PEO:KI:I₂) membranes doped with low viscosity (34 cP at 25 °C) ionic liquid EMImTFSI (1-ethyl 3-methylimidazolium bis(trifluoromethylsulfonyl)imide) showing plasticizing effect as well as improved dye sensitized solar cell efficiency have been reported first time. Apart from ionic conductivity enhancement due to large number of free charge carriers provided by ionic liquid (IL) it assist in reducing cystallinity of polymer electrolyte matrix which was confirmed by polarized optical microscopy (POM). Cyclic voltammetry was carried out to study the reactions of iodide, iodine and IL in polymer electrolyte matrix.     

Deposition of a thin film of TiOx from a titanium metal target as novel blocking layers at conducting glass/TiO2 interfaces in ionic liquid mesoscopic TiO2 dye-sensitized solar cells

In dye-sensitized TiO2 solar cells, charge recombination processes at interfaces between fluorine-doped tin oxide (FTO), TiO2, dye, and electrolyte play an important role in limiting the photon-to-electron conversion efficiency. From this point of view, a high work function material such as titanium deposited by sputtering on FTO has been investigated as an effective blocking layer for preventing electron leakage from FTO without influencing electron injection. X-ray photoelectron spectroscopy analysis indicates that different species of Ti (Ti4+, Ti3+, Ti2+, and a small amount of Ti0) exist on FTO. Electrochemical and photoelectrochemical measurements reveal that thin films of titanium species, expressed as TiOx, work as a compact blocking layer between FTO and TiO2 nanocrystaline film, improving Voc and the fill factor, finally giving a better conversion efficiency for dye-sensitized TiO2 solar cells with ionic liquid electrolytes.     

Tailoring the interface using thiophene small molecules in TiO(2)/P3HT hybrid solar cells

In this paper we focus on the effect of carboxylated thiophene small molecules as interface modifiers in TiO(2)/P3HT hybrid solar cells. Our results show that small differences in the chemical structure of these molecules, for example, the presence of the -CH(2)- group in the 2-thiopheneacetic acid (TAA), can greatly increase the TiO(2) surface wettability, improving the TiO(2)/polymer contact. This effect is important to enhance exciton splitting and charge separation.     

Novel Quasi-solid-state Dye-sensitized Solar Cell Based on Monolayer Capped TiO2 Nanoparticles Framework Materials

Dodecylbenzenesulfonate (DBS)-capped TiO2 nanoparticles have been synthesized and employed in dye-sensitized solar cells to form a quasi-solid state electrolyte. Owing to the long alkyl-chain capping around the TiO2 nanoparticles interacting with the liquid solvent, the dye sensitized solar cell based on such DBS-capped TiO2 nanoparticle framework material gel electrolyte shows higher stability compared with the non-capped one in the long-term application and gives a comparable overall efficiency of 6.3% at AM 1.5 illumination.     

Engineering of efficient panchromatic sensitizers for nanocrystalline TiO(2)-based solar cells.

A new series of panchromatic ruthenium(II) sensitizers derived from carboxylated terpyridyl complexes of tris-thiocyanato Ru(II) have been developed. Black dye containing different degrees of protonation [(C(2)H(5))(3)NH][Ru(H(3)tcterpy)(NCS)(3)] 1, [(C(4)H(9))(4)N](2)[Ru(H(2)tcterpy)(NCS)(3)] 2, [(C(4)H(9))(4)N](3)[Ru(Htcterpy)(NCS)(3)] 3, and [(C(4)H(9))(4)N](4)[Ru(tcterpy)(NCS)(3)] 4 (tcterpy = 4,4',4' '-tricarboxy-2,2':6',2' '-terpyridine) have been synthesized and fully characterized by UV-vis, emission, IR, Raman, NMR, cyclic voltammetry, and X-ray diffraction studies. The crystal structure of complex 2 confirms the presence of a Ru(II)N6 central core derived from the terpyridine ligand and three N-bonded thiocyanates. Intermolecular H-bonding between carboxylates on neighboring terpyridines gives rise to 2-D H-bonded arrays. The absorption and emission maxima of the black dye show a bathochromic shift with decreasing pH and exhibit pH-dependent excited-state lifetimes. The red-shift of the emission maxima is due to better pi-acceptor properties of the acid form that lowers the energy of the CT excited state. The low-energy metal-to-ligand charge-transfer absorption band showed marked solvatochromism due to the presence of thiocyanate ligands. The Ru(II)/(III) oxidation potential of the black dye and the ligand-based reduction potential shifted cathodically with decreasing number of protons and showed more reversible character. The adsorption of complex 3 from methoxyacetonitrile solution onto transparent TiO(2) films was interpreted by a Langmuir isotherm yielding an adsorption equilibrium constant, K(ads), of (1.0 +/- 0.3) x 10(5) M(-1). The amount of dye adsorbed at monolayer saturation was (n(alpha) = 6.9 +/- 0.3) x 10(-)(8) mol/mg of TiO(2), which is around 30% less than that of the cis-di(thiocyanato)bis(2,2'-bipyridyl-4,4'-dicarboxylate)ruthenium(II) complex. The black dye, when anchored to nanocrystalline TiO(2) films achieves very efficient sensitization over the whole visible range extending into the near-IR region up to 920 nm, yielding over 80% incident photon-to-current efficiencies (IPCE). Solar cells containing the black dye were subjected to analysis by a photovoltaic calibration laboratory (NREL, U.S.A.) to determine their solar-to-electric conversion efficiency under standard AM 1.5 sunlight. A short circuit photocurrent density obtained was 20.5 mA/cm(2), and the open circuit voltage was 0.72 V corresponding to an overall conversion efficiency of 10.4%.