等离子体破裂期间电流猝灭特征研究

等离子体破裂会对托卡马克装置的安全运行造成严重威胁.等离子体破裂期间电流猝灭速率与电磁负载的大小及逃逸电流平台的形成都密切相关.本文对HL-2A装置等离子体破裂进行了统计分析,统计选用等离子电流的两个衰减区间90%-10%和80%-20%.分析结果表明:HL-2A装置等离子体破裂有四种不同的电流猝灭波形,两个衰减区间最小电流猝灭时间的参数区分别为2.6 ms和2.2 ms,并且不同衰减区间下平均电流猝灭时间统计分布明显不同.     

托卡马克等离子体电流猝灭特征行为分析

对托卡马克装置内壁产生巨大电磁力是等离子体破裂重要和直接的影响, 这会对装置的安全运行造成巨大威胁. 等离子体破裂期间电流猝灭率不仅与真空室内第一壁的负载设计有关, 并且与装置重大部件的设计也相关. 本文选用100%-40%区间统计研究等离子体破裂现象. 分析结果表明: 100%-40%区间统计下HL-2A上最小电流猝灭时间为0.7 ms, 对应的最小面积归一化电流淬灭时间为1.4 ms m-2. 瞬时最大电流猝灭率与平均电流猝灭率的比值大部分都大于1.     

不同粒径金纳米微粒对荧光素钠的猝灭效应研究

采用柠檬酸盐合成法制备了不同粒径的金纳米微粒,用吸收光谱和透射电镜对金纳米微粒进行了表征。研究了不同粒径金纳米微粒与荧光素钠分子的相互作用。发现金纳米微粒对荧光素钠具有荧光猝灭效应, 并且其荧光猝灭程度与金纳米微粒的粒径大小有关。随着金纳米微粒粒径的减小,荧光猝灭程度增大。探讨了金纳米微粒对荧光素钠荧光猝灭的机理,表明该荧光猝灭为动态猝灭。     

发光温敏漆的制备及其温度猝灭特性研究

以三氯化钌、2—2联吡啶为主要原料,甲基丙烯酸甲酯为基质,制备了钌联吡啶／聚甲基丙烯酸甲酯发光温敏漆,并对其温度猝灭特性进行了研究。扫描电镜观察发现钌联吡啶为规则的层状六边形结构;差热-热重测试表明钌联吡啶在320℃发生分解。紫外吸收光谱分析发现,温敏漆的适合激发光波长区间为410～500nm。荧光光谱测试结果表明温敏...     

污染水体溶解有机物诱导荧光猝灭特性的实验研究

溶解有机物的含量是衡量水质的常用指标,利用荧光方法可以实现对自然水体溶解有机物的浓度进行高灵敏在线遥测。文章利用三维荧光光谱技术对溶解有机物进行了荧光表征,实验研究了溶解有机物浓度与荧光强度的关系,以及水体酸碱度和金属离子对荧光强度的影响。研究表明,当溶解有机物浓度在小于10 mg·L-1,pH值在6.5～7.5范围内时,荧光强度与浓度具有很好的线性关系;金属离子对溶解有机物诱导荧光有较大猝灭作用,不同金属离子对诱导荧光强度的猝灭效果有显著不同。     

有机阱结构器件在反向偏压调制下光致发光猝灭的研究

实验过程中制备了3种不同周期的有机阱结构器件,分别用N,N’-diphenyl-N,N’-bis(1-napthyl)-1,1’-biphenyll-4,4’-diamine(NPB)和4,4,N,N’-dicarbazolebiphenyl(CBP)作为电子的势阱和势垒。讨论了3个器件在反向偏压调制下的光致发光的猝灭。研究结果显示在作者所制备的器件中NPB层中激子的猝灭速度要比CBP层中的激子猝灭速度快。这主要是因为NPB层中的有效电场要比CBP层中的有效电场强。当所制备的有机阱结构器件的周期数增加时,在相同的反向电场下,NPB和CBP层中的激子猝灭速度会随之增加,因为实验中制备的这3个器件为Ⅱ型量子阱结构,激子在这种阱结构器件中会随着阱周期数的增加而变得越来越不稳定,因此周期数较大的器件猝灭现象比较明显。     

低碰撞能下Ne原子对LiH分子转动猝灭的研究

用密耦方法首次研究了Ne原子和LiH分子低能碰撞下的转动猝灭过程.在碰撞能低于10-4cm-1时,弹性截面趋于常数值,非弹性截面随碰撞速度减小线性增加,遵循Wigner定则预言的趋势.对于一个给定的能量,总的猝灭截面是随着初始j的增加而减少的.当能量在0.01~100 cm-1范围内,弹性和非弹性截面均比其它的体系表现出更复杂的振荡行为,这主要是由于体系具有强的各向异性以及它们具有两个吸引阱而造成的.计算表明,在零温极限下,猝灭速率系数达到10-11cm3s-1数量级.当j=7速率系数出现反转结构.     

低混杂波高N‖分量对EAST等离子体电流驱动的影响

EAST等离子体高约束模运行条件下,在等离子体边缘区域观测到明显的等离子体电流带.在EAST托卡马克装置非圆截面平衡位形下,使用射线追踪方法研究低混杂波高平行折射率N_‖分量对电流驱动的影响.结果表明：当-8≤N_‖≤-6时,平行折射率分量能够在小半径（0.7 < r/a < 1）区域驱动kA量级的等离子体电流.对于具有台基区、等离子体边缘温度更高的电子温度剖面,驱动电流的位置r/a>0.9.低混杂波朗道阻尼的理论分析与数值模拟结果一致.另外,高N_‖低混杂波在等离子体边缘的功率沉积和电流驱动与电子温度分布和发射谱分布相关.     

单质碘对水溶性CdTe量子点的荧光猝灭研究

合成了不同尺寸的、巯基丙酸和半胱氨酸修饰的水溶性CdTe量子点,并研究了I2与CdTe量子点的相互作用,实验发现I2能够明显猝灭CdTe量子点的荧光,且猝灭程度与量子点的修饰剂有关,没有表现出明显的尺寸依赖效应。     

Charge/discharge characteristics of sulfur composite electrode at different temperature and current density in rechargeable lithium batteries

The charge/discharge characteristics of the sulfur composite cathodes were investigated at different temperatures and different current densities. The composite presented the discharge capacities of 854 and 632 mAh g⁻¹ at 60 and −20 °C, respectively, while it had the discharge capacities of 792 mAh g⁻¹ at 25 °C. The composite presented the discharge capacities of 792 and 604 mAh g⁻¹ at 55.6 and 667 mA g⁻¹, respectively, at room temperature. The results showed that the sulfur composite cathodes presented good charge/discharge characteristics between 60 and −20 °C and at a high c-rate up to 667 mA g⁻¹.     

Characterization of plasma current quench during disruption in EAST tokamak

A preliminary analysis of plasma current quenching is presented in this paper based on the disruption database.It demonstrates that 26.8%of discharges have been disrupted in the last 2012 campaign,in addition,the plasma disruptive rate grows with the increase of plasma current.The best-fit linear and instantaneous plasma current quench rate is extracted from the recent EAST disruptions,showing that an 80%-30%interval of the maximum plasma current is well fit for the EAST device.The lowest area-normalized current quench time is 3.33 ms/m~2 with the estimated plasma electron temperature being 7.3 eV~ 9.5 eV.In the disruption case the maximum eddy current goes up to 400 kA,and a fraction of currents are respectively driven on the upper and lower outer plate with nearly 100 MPa-200 MPa stress in the leg.     

���˹�������Ԥ��HL-2A��������ŵ�����

使用人工神经网络(ANN)对HL-2A装置破裂放电进行了离线预测研究。采用了两种方法训练网络,一种方法是采用原始实验数据作为网络输入训练网络,另一种是把训练样本中的Mirnov原始实验信号进行预处理,目的是突出Mirnov原始信号隐含的破裂信息。比较这两种方法,结果表明第二种方法获得的网络对破裂放电能够做出更加准确的预测。     

用人工神经网络预测HL-2A等离子体放电破裂

使用人工神经网络(ANN)对HL-2A装置破裂放电进行了离线预测研究。采用了两种方法训练网络,一种方法是采用原始实验数据作为网络输入训练网络,另一种是把训练样本中的Mirnov原始实验信号进行预处理,目的是突出Mirnov原始信号隐含的破裂信息。比较这两种方法,结果表明第二种方法获得的网络对破裂放电能够做出更加准确的预测。     

超高速大电流半导体开关实验研究

 利用自行研制的固态半导体开关RSD,采用电容储能方式,研究了RSD的电压响应时间、大电流特性、电流上升率等。在测试RSD的电压响应时间时,得到了25 ns的电压下降曲线。在主电容电压为8 kV时,得到峰值为10.1 kA、脉宽为34 μs、电流上升率为2.03 kA/μs的大电流脉冲。通过调整主电路,在主电容为3 kV时,得到的电流脉冲峰值为8.5 kA、脉宽为2.5 μs、电流上升率为7.2 kA/μs。结果表明,RSD是一种开通快、通流能力强、电流上升率高的大功率半导体开关器件。     

Study of current drain during electrochemical etching of polycarbonate detectors

Polycarbonate (PC) detector is one of the common detectors for neutron and radon gas detection. Using this detector it is possible to measure the dose in mSv, by counting tracks/cm² on an etched surface. In this paper, a special procedure has been suggested to determine the dose based on current drain during the etching process. In these experiments the effects of voltage, frequency, effective etched area, PC detector's thickness, etched area (one side or two sides), etching solution temperature and dose absorbed by the PC foil have been studied.The results obtained show the current drain variation for a voltage of 200–1600 V, a frequency of 2–10 kHz, effective area with a diameter of 2–12 cm, PC thickness of 125–250–375– and a temperature of etching solution of 25–.Lexan PC foils were exposed to doses of of neutrons. The unexposed foils were considered as the background (BG) foils. Most of the experiments were performed at a voltage of 800 V, a frequency of 2 and 8 kHz, foil thickness of , diameter of effective etched area of foils of 2, 6 and 12 cm, temperatures of 25 and and the etching process from 0 up to overload stage. Overload stage occurs when the foil becomes so thin due to growth of the tracks that it leads to sparking between phase and null that makes a hole in the foil.Current drain curves versus the function of the etching time are absolutely different for various doses from zero (BG) to 10 rad (BG up to ). This is true especially for the time interval from 3 h of etching up to overload stage. In this way, it is possible to obtain a calibration of PC detector net current drain based on its absorbed dose.In this experiment, the number and diameter of tracks and their relation with drain current and PC foil residual thickness at overload stage have been studied.The same experiment has been performed for various concentrations of radon gas (Bq/m3) as well.     

Surface characteristics and antistatic mechanism of plasma-treated acrylic fibers

Acrylic fibers are treated by nitrogen glow-discharge plasma to promote surface antistatic properties. The treated surfaces are characterized by scanning electron microscopy (SEM), specific surface area analysis (BET) and X-ray photoelectron spectroscopy (XPS). Plasma treatment is found to increase the surface roughness, to modify the nature and density of surface functionalities, and to drastically improve the wettability and antistatic ability of acrylic fibers.     

不同轨道结构下电枢电流分布特性

解决轨道和电枢的烧蚀问题是六极轨道电磁发射器走向实际应用的关键环节,引起轨道和电枢烧蚀的原因之一就是轨道和电枢中电流分布不均匀。利用有限元仿真软件Ansoft Maxwell对三种不同轨道进行仿真,得到了电枢表面电流密度分布情况以及电枢受力。结果表明：矩形轨道对应电枢表面电流密度最大值在三种轨道中最小,凸出半圆形轨道枢轨接触面电流分布最均匀,在发射过程中可以有效减少轨道和电枢的烧蚀,凹陷半圆形轨道对应的电枢受力最大,可用于大质量物体的发射。     

高功率微波在等离子体填充波导中的传播特性

 在考虑有质动力情况下对高功率微波在等离子体填充波导中的传播特性进行了理论分析和数值计算,研究了高功率微波在等离子体中的传播特性和微波场强与等离子体密度分布之间的关系。结果表明高功率微波的有质动力将影响微波色散特性,使微波场强分布偏离Bessel分布,并对等离子体有排开作用,当场强足够大时可将波导中心处等离子体排空形成低密度通道。