Speciation studies by capillary electrophoresis- Simultaneous determination of chromium(III) and chromium(VI)

A method for the simultaneous determination of chromium(III) and chromium(VI) by capillary electrophoresis (CE) has been developed. The chromium(III) has been chelated with 1,2-cyclohexanediaminetetraacetic acid (CDTA) in order to impart a negative charge and similar mobility to both the chromium(III) and the chromium(VI) species. The effects of the amount of the reagent, pH and heating time required to complete the complexation have been studied. Factors affecting the CE behaviour such as the polarity of electrodes and the pH of electrophoretic buffer have been investigated. The separated species have been monitored by direct UV measurements at 214 nm. The detection limits achieved are 10 g/l for Cr(VI) and 5 g/l for Cr(III) and linear detector response is observed up to 100 mg/l. The procedure has been applied to the determination of both chromium species in industrial electroplating samples and its accuracy was checked by comparing the results (as total chromium) with those of atomic absorption spectrometry. No interference occurred from transition metal impurities under optimized separation conditions. The method is also shown to be feasible for determining Cr(III) as well as other metal ions capable to form complexes with CDTA (like iron(III), copper(II), zinc(II) and manganese(II)) in pharmaceutical preparations of essential trace elements.     

Speciation studies by capillary electrophoresis- Simultaneous determination of chromium(III) and chromium(VI)

A method for the simultaneous determination of chromium(III) and chromium(VI) by capillary electrophoresis (CE) has been developed. The chromium(III) has been chelated with 1,2-cyclohexanediaminetetraacetic acid (CDTA) in order to impart a negative charge and similar mobility to both the chromium(III) and the chromium(VI) species. The effects of the amount of the reagent, pH and heating time required to complete the complexation have been studied. Factors affecting the CE behaviour such as the polarity of electrodes and the pH of electrophoretic buffer have been investigated. The separated species have been monitored by direct UV measurements at 214 nm. The detection limits achieved are 10 microg/l for Cr(VI) and 5 microg/l for Cr(III) and linear detector response is observed up to 100 mg/l. The procedure has been applied to the determination of both chromium species in industrial electroplating samples and its accuracy was checked by comparing the results (as total chromium) with those of atomic absorption spectrometry. No interference occurred from transition metal impurities under optimized separation conditions. The method is also shown to be feasible for determining Cr(III) as well as other metal ions capable to form complexes with CDTA (like iron(III), copper(II), zinc(II) and manganese(II)) in pharmaceutical preparations of essential trace elements.     

Simultaneous determination of chromium(VI) and chromium(III) at trace levels by adsorptive stripping voltammetry

A new methodology was proposed for the speciation of chromium by differential pulse adsorptive stripping voltammetry (DPAdSV) using pyrocatechol violet (PCV) and N-(2-hydroxyethyl)ethylenediamine-N,N′,N′-triacetic acid (HEDTA) as complexing agents. In this procedure, a partial least squares (PLS) regression was used for the resolution of the strongly overlapping voltammetric signals from mixtures of Cr(III) and Cr(VI) in the presence of PCV and HEDTA. The relative error in absolute value was <6% when concentrations of several mixtures were calculated. The analysis of the possible effect of the presence of foreign ions in the solution was performed. The procedure was successfully applied to the speciation of chromium in different samples of natural water.     

Simultaneous determination of chromium (III) and chromium (VI) by reversed-phase ion-pair HPLC with chromium-specific detection

A method for the simultaneous determination of Cr(III) and Cr(VI) with reversed-phase ion-pair HPLC employing chromium-specific detection by flame atomic absorption spectrometry (FAAS) and inductively-coupled plasma mass spectrometry (ICP-MS) is presented. Experimental parameters of the chromatographic separation, such as concentration of the ion-pairing reagent, pH and polarity of the mobile phase have been optimized for two different ion-pairing reagents, tetrabutylammonium phosphate (TBA) and tetraethylammonium nitrate (TEA). Best chromatographic conditions have been obtained with a polymer-based reversed-phase column (Hamilton PRP1) and mobile phases containing either TBA (1 mmol/l) in methanol-water (60:40, v/v) or TEA (2 mmol/l) in water at a pH between 3 and 4. With FAAS the detection limits (3) have been found to be 24 g/l for Cr(III) and 40 g/l for Cr(VI). A detection limit of 0.3 g/l Cr(3) for both chromium species has been obtained when ICP-MS has been used for detection. The method has been applied to analyze tap- and groundwater and to investigate the behaviour of Cr(III) and Cr(VI) in spiked tap-water, as well as to analyze aqueous extracts of coal fly ash (NIST SRM 1633a) and of an ash from a wood treatment company.     

Simultaneous determination of chromium(VI) and chromium(III) by flame atomic absorption spectrometry with a chelating ion-exchange flow injection system

Summary Simultaneous Determination of Chromium(VI) and Chromium(III) by Flame Atomic Absorption Spectrometry with a Chelating Ion-Exchange Flow Injection System A simple method is described for the simultaneous determination of chromium(VI) and chromium(III) in a flow injection system comprising chelating ion-exchange and flame atomic absorption spectrometry. Sampling rates for 2001 and 1 ml sample volumes were 120 and 60 h^–1 (240 and 120 speciations per hour), respectively. Typical relative standard deviations were 0.52% for Cr(VI) (0.50g ml^–1 and 0.67% for Cr(III) (0.10,g ml^–1) and the corresponding limits of detection were 85 ng ml^–1, and 16 ng ml^–1, respectively.On leave from University of Belgrade.     

Spectrophotometric determination of cyanide by unsegmented flow methods

Photometric methods for cyanide determination by normal and reversed FIA techniques and by completely continuous monitoring are proposed. The sampling rates for the first two techniques are 20 and 28/hr, respectively, the r.s.d. being less than 0.8% in both cases. A simulation of cyanide control in industrial waste waters shows the usefulness of the continuous monitoring method.     

Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection.

A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both species were detected by use of the luminol-hydrogen peroxide chemiluminescence system. Linear calibration for both species was established over the concentration range 1-1000 micrograms l-1. The precision at the 20 micrograms l-1 level was 3.5% for chromium(iii) and 3.3% for chromium(vi), respectively. The detection limit was 0.5 micrograms l-1 for both species. Data were in agreement with Zeeman-effect background corrected atomic absorption spectrometry measurements.     

Simultaneous flow injection determination of iron(III) and vanadium(V) and of iron(III) and chromium(VI) based on redox reactions

A flow injection analysis (FIA) method is presented for the simultaneous determinations of iron(III)-vanadium(V) and of iron(III)-chromium(VI) using a single spectrophotometric detector. In the presence of 1,10-phenanthroline (phen), iron(III) is easily reduced by vanadium(IV) to iron(II), followed by the formation of a red iron(II)-phen complex (lambda(max) = 510 nm), which shows a positive FIA peak at 510 nm corresponding to the concentration of iron(III). On the other hand, in the presence of diphosphate the reductions of vanadium(V) and/or chromium(VI) with iron(II) occur easily because the presence of diphosphate causes an increase in the reducing power of iron(II). In this case iron(II) is consumed during the reaction and a negative FIA peak at 510 nm corresponding to the concentration of vanadium(V) and/or chromium(VI) is obtained. The proposed method makes it possible to obtain both positive (for iron(III)) and negative (for vanadium(V) or chromium(VI)) FIA peaks with a single injection.     

In-situ separation of chromium(III) and chromium(VI) and sequential ETV-ICP-AES determination using acetylacetone and PTFE as chemical modifiers

Electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-ES) has been used for the sequential determination of Cr(III) and Cr(VI). The method is based on the difference between the chelate reactions of the two Cr species and acetylacetone. Cr(III) chelate was separated from Cr(VI) and determined with use of acetylacetone as chemical modifier. The retained Cr(VI) in graphite tube was analyzed subsequently, after addition of polytetrafluoroethylene (PTFE) as chemical modifier. The different factors affecting the vaporization behavior of Cr(III) acetylacetonate were investigated in detail. The detection limits for Cr (III) and Cr(VI) were 0.56 and 1.4 ng mL(-1), respectively, and relative standard deviations for 0.1 microg mL(-1) Cr(III) and 0.1 microg mL(-1) Cr(VI) were 2.5% (n = 6) and 4.8% (n = 6), respectively. The linear ranges of the calibration curve for both Cr(IIl) and Cr(VI) covered three orders of magnitude. The proposed method was used to analyze water samples with satisfactory results.     

Spectrophotometric determination of chromium(III, VI) by use of chromium(III, VI)-Chrome AzurolS-cetylpyridinium bromide-hydroxylamine hydrochloride-zinc(II) system

This paper shows that the sensitivity of the Cr(III, VI)—Chrome Azurol S (CAS)-cetylpyridinium bromide (CPB)—hydroxylamine hydrochloride system can be increased and the wavelength of maximum absorption slightly shifted by addition of zinc(II) and that the analytical data are practically identical for both Cr(III) and Cr(VI), indicating that under the conditions used both initial oxidation states of chromium yield the same final oxidation state, Cr(III). On the basis of the Cr(III, VI)—CAS—CPB—NH₂OH·HCl—Zn systems a new, highly sensitive and selective method for spectrophotometric determination of microamounts of Cr(III, VI) has been developed, with molar absorptivity of 1.27 × 10⁵ 1. mole⁻¹ . cm⁻¹ for the complex at 620 nm and linear calibration up to 0.4 μg/ml chromium. Various foreign ions do not interfere. The method can be applied to direct determination of chromium in steels.     

Speciation of chromium(III) and chromium(VI) by in situ separation and sequential determination with electrothermal vaporization inductively coupled plasma atomic emission spectrometry

A novel method for the speciation of chromium(III) and chromium(VI) by in situ separation and sequential determination with electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-AES) was developed. The reaction conditions between Cr(III) and 8-hydroxyquinoline (8-Ox) and the vaporization behavior of the chelate formed were investigated in detail. It was found that the Cr(III)-8-Ox chelate could be formed at room temperature and vaporized from graphite furnace under controlled experimental conditions, therefore, an in situ separation of Cr(III) from Cr(VI) was achieved. The retained Cr(VI) in graphite tube was then determined by using fluorination vaporization ETV-ICP-AES with PTFE slurry as chemical modifier. Under optimum experimental conditions, the detection limits for Cr(III) and Cr(VI) are 8.6 ng/ml and 11.3 ng/ml, and the relative standard deviations (R.S.D.s) are 3.8% and 4.1% (c=0.1 μg/ml, n=6), respectively. The linear ranges of the calibration curve for both Cr(III) and Cr(VI) covered three orders of magnitude. The proposed method has been applied to the speciation of Cr(III) and Cr(VI) in water samples with the satisfactory results.     

Flavin mononucleotide chemiluminescence in cationic micellar media for determination of chromium(III + VI) by flow injection

The flavin mononucleotide chemiluminescence system, originally developed for the determination of copper(II), is modified with cationic surfactant micelles for the determination of chromium(III + VI). In order for chromium to be detected predominantly, the copper-induced luminescent reaction is significantly suppressed by virtue of the cationic micellar effect. The limit of detection (signal-to-noise ratio = 2) is 5 × 10^?8 M chromium (50-μl sample injection).     

Indirect spectrophotometric determination of traces of antimony(III) based on its oxidation by chromium(VI) and reaction of chromium(VI) with diphenylcarbazide

An indirect method for the determination of antimony(III) is described. Antimony(III) is oxidized to antimony(V) by chromium(VI) and the excess of chromium(VI) is then determined spectrophotometrically with diphenylcarbazide. Optimal conditions were established for both the determination of antimony(III) and the elimination or reduction of interferences. Antimony(III) can be determined quickly and easily in the range 0.05–5 mg l^?1; the relative standard deviation is 2% for 1.0 mg l^?1 antimony(III). The method is applicable to marine sediments and geothermal waters.     

Iodometric microgram determination of chromium(III) and (VI) by use of chemical amplification reactions

A simple, rapid and sensitive method is described for the iodometric determination of microgram amounts of chromium(III), based on the oxidation of chromium(III) with periodate at pH 3.2, removal of the unreacted periodate by masking with molybdate and subsequent iodometric determination of the liberated iodate. Chromium(VI) can be determined by this method after prior reduction to chromium(III) with sodium sulphite. The method can also be used for the analysis of organochromium compounds.     

Method for the determination of chromium (VI) as chromium (VI)-dibenzyidithiocarbamate

Dibenzyldithiocarbamic acid (DBDC) exhibits the ability to speciate between chromium(VI) and chromium(III), since only the chromium(VI) will form complexes with DBDC. The complex is then extracted into an organic solvent and assayed using an ultraviolet-visible (UV-VIS) spectrophotometer at 498.8 nm. Using 250 ml of aqueous sample detection limits less than 1 ng/ml are possible, while the linear range extends to 500 gmg/ml when working at 498.8 nm. Oxidation of the chromium(III) to chromium (VI) using cerium (IV) enables the determination of total chromium and subsequently the chromium (III) in solution. Evaluation of the method with a standard reference material produced only 4.81 part per thousand error in the determination of chromium(VI).     

Ion-chromatographic determination of chromium (VI)

Summary A simple ion-chromatographic method has been developed for the selective determination of chromium (VI) using UV-photometric detection. The anion exchanger was based on a matrix of a 2-hydroxyethyl-methacrylate copolymer; the mobile phase consisted of phosphate buffer and sodium perchlorate. The relative standard deviation was 2.26%. Application was made to waste waters of the metallurgical industry.     

Simultaneous determination of vanadium and lead in unsegmented flow systems of variable flow rate

Summary A completely continuous flow system and one with injection of the sample based on variable flow rates were used to develop a simultaneous determination for vanadium(V) and lead(II). Each metal ion is complexed with 4-(2-pyridyl-azo) resorcinol at a different pH which was established in the flow system by changing the flow rate. The features of the proposed determinative methods are discussed and compared with those of others reported in the literature.     

Simultaneous determination of chromium (III) and copper (II) by using derivative spectrophotometry with MEDTA

The application of derivative spectrophotometry to the simultaneous determination of chromium (III) and copper (II) with MEDTA is described. The procedure is suitable for concentrations of 0.40–2.60 mg ml⁻¹ of chromium (III) and 0.15–0.60 mg ml⁻¹ of copper (II). The main interferences, both anionic and cationic, are easily eliminated. The method was applied to different aqueous matrices. It was compared with an atomic absorption method and good results were obtained.     

Preconcentrative separation of chromium(III) species from chromium(VI) by cloud point extraction and determination by flame atomic absorption spectrometry

Microchimica Acta - We describe a high-throughput technique for the determination of chromium species in water samples by flame atomic absorption spectrometry (FAAS) after preconcentrative...     

Simultaneous determination of arsenic species and chromium(VI) by high-performance liquid chromatography-inductively coupled plasma-mass spectrometry

The simultaneous determination of As(III), As(V), monomethylarsenic acid (MMA), dimethylarsinic acid (DMA) and Cr(VI) in fresh water has been carried out by coupling an anion-exchange column to an inductively coupled plasma-mass spectrometer. Optimisation of chromatographic conditions led to baseline separation of signals from the five species in approximately 9 min using gradient elution. Detection limits were 0.02-0.05 microg As l(-1) and 5.5 microg Cr l(-1). Repeatability was 2-3% for arsenic species and higher, i.e., 8%, for Cr(VI) due to the higher background for this species. Arsenic species and hexavalent chromium stability in surface water samples was evaluated, and storage conditions were set to 1 day at 4 degrees C in polyethylene flasks (without acidification) in order to avoid As(III)-As(V) conversions. The method was applied to the analysis of surface water.