支撑液膜研究及应用进展

支撑液膜技术是高选择性膜分离技术,本文对支撑液膜分离技术的研究进展进行了回顾,详述了用于金属离子分离的支撑液膜所采用的载体、影响支撑液膜稳定性的原因以及改善途径,并对支撑液膜的发展前景进行了展望。     

Determination of free copper concentrations in natural waters by using supported liquid membrane extraction under equilibrium conditions

A method is described for measurement of freely dissolved copper concentrations in natural water samples using supported liquid membrane (SLM) extraction under equilibrium conditions, a technique denoted equilibrium sampling through membranes (ESTM). For this purpose, 1,10-dibenzyl-1,10-diaza-18-crown-6 as neutral carrier and oleic acid were used in the membrane phase. The main variables optimised were the carrier used to form the metal complexes, the organic solvent used in the membrane, the countercation, pH, the ligand used in the acceptor phase, the extraction time, and the flow rate of the donor phase. After the optimisation process an enrichment factor of 18.5 was obtained. Equilibrium conditions were reached after extraction for 60 min if a flow rate of 1.0 mL min^–1 or greater was used. When different ligands such as humic acids, phthalic acid, and EDTA were added to the sample solution, and sample pH ranged from 6 to 8, the results obtained for freely dissolved copper concentrations were in a good agreement with results from speciation calculations performed with Visual Minteq V 2.30, Cheaqs V L20.1, and WinHumic V. The developed technique was applied to analysis of stream and leachate water.Electronic Supplementary Material Supplementary material is available for this article at     

Separation of lignosulfonate from its aqueous solution using supported liquid membrane

This paper presents an experimental and theoretical study on facilitated transport of lignosulfonate (LS) through a flat sheet supported liquid membrane using trioctylamine (TOA) as carrier and dichloroethane as diluent. The studies were carried out with various support materials and operating conditions (viz. carrier concentration, strip phase concentration, salt concentration, etc.) and their effects on the transport of LS. The results were analyzed to identify a suitable combination of support and operating condition that would yield best performance of the supported liquid membrane (SLM) in terms of fast and efficient transport of LS. The stability of the SLM was assessed in terms of loss of liquid from the pores of membrane support. The SLM is found to be stable till 10 h. Co-transport mechanism has been adopted in this work by using NaOH as the strip phase. It was observed that extraction of LS is increased with increase in concentration of NaOH up to a limiting value of 0.5 M NaOH. Difference of salt concentration between feed and strip phase considerably affect the separation process. The diffusional resistances of organic membrane (Δorg) and aqueous solution (Δaq) calculated from the permeation model, which is again a combination of three unique mechanisms viz., diffusion through a feed aqueous layer, a fast interfacial chemical reaction, and diffusion of carrier–complex through the organic membrane, are found to be 609.9 and 176.6 s cm⁻¹, respectively. The values of the diffusion coefficient in the membrane (D_org) and in the bulk organic phase (D_complex) are 1.67×10⁻⁹ and 6.68 × 10⁻⁸ m²s⁻¹, respectively. The extraction of LS is about 90%. Nearly 43% of LS can be recovered at optimum condition.     

液膜萃取本地产烟叶中烟碱的研究

采用液膜萃取技术对本地产烟叶的烟碱进行了分析,膜载体使用0.45 μm的PVC油膜和定性滤纸,浸泡膜载体的溶剂分别使用十一烷,十六烷和CHCl3.液膜萃取后的样品经GC/MS分析表明,滤纸作为膜载体的萃取效率明显高于PVC油膜;相同膜载体的情况下,以CHCl3浸泡的膜载体的萃取效果比较好.文中还对两种膜载体在不同溶剂浸泡下的烟碱的萃取效率以及最佳萃取时间进行了研究.     

Simultaneous separation of mercury and lignosulfonate from aqueous solution using supported liquid membrane

This paper presents an experimental investigation on facilitated and simultaneous transport of mercury and lignosulfonate (LS) through a flat sheet supported liquid membrane (SLM) having Nylon 6,6 as support, trioctylamine (TOA) as carrier and dichloroethane as solvent. The experiments were performed at various operating conditions such as strip phase concentration, feed pH, carrier concentration and feed concentration to find the best set of parameters that would yield the maximum separation of pure mercury as well as its mixture with LS. The experiments were performed in co-transport mode using NaOH as the strip phase. It was observed that extraction of mercury as well as its mixture increases with increase in concentration of NaOH up to a certain limit 0.1 M NaOH in case of pure solution and 0.2 M NaOH in case of mixture). Feed phase pH significantly affects the mercury separation process. However, initial feed concentration does not affect the extraction process appreciably. Separation of mixture of mercury and LS behaves in a similar way as their pure solution; however the extraction is low in comparison to pure solution. The extraction of mercury from its pure solution is about 81% in 1 h. The extraction of mercury and LS from their mixture is about 52.6% and 50.2%, respectively at optimum condition and in a period of 2 h.     

Chromium(III, VI) speciation analysis with preconcentration on a maleic acid-functionalized XAD sorbent

Chromium may exist in environmental waters as Cr(III) and Cr(IV), the latter being the toxic and carcinogenic form. Since atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry can only yield information on total Cr concentration, a polymer resin bearing O,O-donor chelating groups such as the maleic acid-functionalized XAD(CO)CHCHCOOH resin was synthesized to selectively retain Cr(III) at pH 4.0-5.5. The dynamic breakthrough capacity of the resin for Cr(III) at pH 5.0 was 7.52 mg g⁻¹, and the preconcentration factor extended to 250-300. Chromium(III) in the presence of 250-fold Cr(VI)—which was not retained—could be effectively preconcentrated on the NH₄⁺-form of the resin and determined by AAS or diphenylcarbazide (DPC) spectrophotometry. When Cr(VI) was reduced to Cr(III) with Na₂SO₃ solution brought to pH 1 by the addition of 1 M H₂SO₄, and preconcentrated on the resin, total Cr could be determined. The developed method was validated with a blended coal sample CRM-1632. Since the adsorption behavior as a function of pH of possible interferent metal ions, e.g. Ni(II), Co(II), Cu(II), Cd(II), Zn(II), Pb(II) and Fe(III), was similar to that of Cr(III), selective elution of Cr(III) from the resin was realized using a mixture of 1 wt.% H₂O₂+1 M NH₃. The eluate containing Cr as chromate could be directly analyzed by diphenyl carbazide spectrophotometry without any adverse effect from the common interferents of this method, i.e. Fe(III), Cu(II) Hg(II), VO₃⁻, MoO₄²⁻ and WO₄²⁻. Various synthetic waste solutions typical of electroplating bath effluents containing Cr, Cu, Ni, Zn, Na, Ca, cyanide (and chemical oxidation demand (COD), achieved by glucose addition) were subjected to pretreatment procedures such as hypochlorite oxidation (of cyanide) and catalytic oxidation (of COD) with peroxodisulfate. Chromium determination gave satisfactory results. The combined column preconcentration—selective elution—diphenylcarbazide spectrophotometric determination was also successfully applied to the determination of Cr in artificial and real seawater.     

Drop-to-drop microextraction across a supported liquid membrane by an electrical field under stagnant conditions

Electromembrane extraction (EME) of basic drugs from 10 μL sample volumes was performed through an organic solvent (2-nitrophenyl octyl ether) immobilized as a supported liquid membrane (SLM) in the pores of a flat polypropylene membrane (25 μm thickness), and into 10 μL 10 mM HCl as the acceptor solution. The driving force for the extractions was 3–20 V d.c. potential sustained over the SLM. The influence of the membrane thickness, extraction time, and voltage was investigated, and a theory for the extraction kinetics is proposed. Pethidine, nortriptyline, methadone, haloperidol, and loperamide were extracted from pure water samples with recoveries ranging between 33% and 47% after only 5 min of operation under totally stagnant conditions. The extraction system was compatible with human urine and plasma samples and provided very efficient sample pretreatment, as acidic, neutral, and polar substances with no distribution into the organic SLM were not extracted across the membrane. Evaluation was performed for human urine, providing linearity in the range 1–20 μg/mL, and repeatability (RSD) in average within 12%.     

Chromium speciation using an automated liquid handling system with inductively coupled plasma - mass spectrometric detection

The speciation of inorganic chromium in environmental samples is required for accurate assessment of pollution levels. Of the two chromium oxidation states, Cr (VI) is a known carcinogen, while Cr (III) is an essential element. Total chromium measurement cannot be used to determine actual environmental impact due to the considerable difference in toxicity of the two elemental forms. An automated liquid handling system, the PrepLab™, can be used with an inductively coupled plasma-mass spectrometer (ICP-MS) to quantify Cr (III) and Cr (VI) in liquid samples. An autosampler is used to introduce discrete sample volumes into a solid-phase chelation resin column. The Cr (III) and Cr (VI) species are separated and are introduced on-line into the VG PlasmaQuad 3 ICP-MS for detection. The chromatographic data are collected in time resolved analysis mode with the capability of simultaneous multiple-isotopic detection.     

Continuous flow liquid membrane extraction: a novel automatic trace-enrichment technique based on continuous flow liquid-liquid extraction combined with supported liquid membrane

Combining the continuous flow liquid-liquid extraction (CFLLE) and supported liquid membrane (SLM) extraction, a novel aqueous-aqueous extraction technique that we termed continuous flow liquid membrane extraction (CFLME) is developed for trace-enrichment. The analyte was firstly extracted into the organic phase in the CFLLE step, then transported onto the organic liquid membrane that formed on the surface of the micro porous membrane of the SLM equipment. Finally, it passed through the liquid membrane and was trapped by the acceptor. Aspects related to CFLME were studied by using dichloromethane as liquid membrane, and sulfonylurea herbicides as model compounds. An enrichment factor of over 1000 was obtained when 10 μg l⁻¹ of MSM was enriched for 120 min by this technique. The drawbacks of only a few organic solvents can be selected as liquid membrane with a limited lifetime in SLM operation was overcome. In this CFLME method, almost all solvents that used in the conventional liquid-liquid extraction (LLE) can be adopted and the lifetime of liquid membrane is no longer a problem.     

Extraction and carrier mediated transport of urea using noncyclic receptors through liquid membrane systems

Extraction and carrier mediated transport through bulk liquid membrane and supported liquid membrane systems have wide applications in separation technology. This paper highlights the use of six noncyclic receptors (podands) having variations in chain length and end group for the removal of urea using liquid membrane system. These receptors R_1, R_2, R_3, R_4, R_5, R₆ are diethylene glycol dimethyl ether, diethylene glycol dibutyl ether, diethylene glycol dibenzoate, diethylene glycol, triethylene glycol and tetraethylene glycol respectively. The sequence of extraction and transport of urea by BLM system using various receptors is R₂ > R₃ > R₁ > R₄ > R₅ > R₆ and R₆ ≈ R₃ > R₅ > R₄ > R₁ > R₂ respectively. Receptor R₂ containing butyl end group is best extractant while receptor R₆ with flexible backbone is best carrier and this carrier efficiency is used to remove urea using BLM system from the feed phase by recyclization process up to 88.16%. The experimental results influenced by concentration of receptors and urea. Effect of time was also studied.     

Transport of carbonate ions through supported liquid membrane by using Alamine 336 and trioctylphosphine oxide as carriers

Abstract

Transport studies were carried out for carbonate ions through supported liquid membrane (SLMs) by using Alamine 336 and trioctylphosphine oxide (TOPO) as carriers. Experimental variables were investigated, such as concentration of carbonate ion (10^?5 to 4×10^?2 M), carriers (10^?5 to 10^?1 M), and alkali (0.01–0.5); and stirring speed (50–150 rpm) of bulk solutions. The use of combined carriers Alamine 336 and TOPO shows a synergic transport of carbonate ions. The stability of the SLM system in relation to the transport of carbonate ions has been studied. The enrichment of carbonate ions (10^?6 to 4×10^?2 M) from the dilute solution was explored. The different combinations of amines with TOPO show synergic permeability of the carbonate ions through SLM system.     

Chromium speciation study in polluted waters using catalytic adsorptive stripping voltammetry and tangential flow filtration

The catalytic adsorptive stripping voltammetry (CAdSV) has been applied to physico-chemical chromium speciation study in the upper Dunajec catchment, severely polluted by the tannery wastewater. The method is based on the adsorptive preconcentration of the Cr(III)-diethylenetriammine-N,N,N′,N″,N″-pentaacetic acid (DTPA) complex and the utilization of the catalytic reaction in the presence of nitrate. Under optimized conditions the CAdSV enables the oxidation state speciation study of Cr content by direct determination of Cr(VI) in the presence of the predominant Cr(III) concentration with the detection limit for chromium(VI) of 0.08 nM and the linearity range from 0.1 to 80 nM obtained for 20 s of accumulation, as well as the determination of total Cr after UV oxidation of Cr(III) to Cr(VI). Due to the difference in the chemical properties of different chromium species the CAdSV method makes possible a speciation study of Cr(III) and Cr(VI) oxidation state. The RSD of the determination of Cr(VI) and Cr(III) varies from 0.5 to 5%. It has been proved that in natural water in which strong complexants of Cr(III) such a humid acids are presented, Cr(VI) can be determined accurately in the presence of high excess of Cr(III). Fractionation of selected water samples with tangential flow filtration (TFF, cut-off 10 and/or 1 kDa) provides insight into physical Cr speciation, i.e. partitioning of the Cr(VI) and Cr(III) between the colloidal and the dissolved fractions. It has been shown that the content of the Cr species in the Dunajec river depends on the season, and is significantly higher in autumn and winter during the most intensive tanneries production processes. The concentration of total Cr exceeds occasionally the legally admissible level. A large fraction of total Cr(III) concentration is associated with the colloidal material, while Cr(VI) occurs solely in the truly dissolved form.     

Automated sample preparation using supported liquid membranes for liquid chromatographic determination of sulfonylurea herbicides

Summary Sample preparation for determination of sulfonylurea herbicides in aqueous samples is investigated. The technique studied utilizes extraction and back extraction in an automated flow system and is coupled on-line to a liquid chromatographic system. The extraction unit consists of an immobilized liquid membrane, separating two aqueous phases. From the acidified donor phase the analytes are extracted into the organic solvent of the membrane. After traversing the membrane they are back extracted into an alkaline/neutral aqueous acceptor phase. They are trapped in the acceptor by dissociation, making them insoluble in the membrane.Studies of the sample preparation system concern factors like channel length of separators, distribution coefficients of analytes and use of a precolumn instead of loop for chromatographic injections. Effects of the internal diameter of the analytical column as well as the detection of the sulfonylurcas are investigated.     

Toward the use of surface modified activated carbon in speciation: selective preconcentration of selenite and selenate in environmental waters

This paper describes a novel application of tetrabutylammonium hydroxide-modified activated carbon (AC-TBAH) to the speciation of ultra-trace Se(IV) and Se(VI) using LC-ICP-DRC-MS. The anion exchange functionality was immobilized onto the AC surface enables selective preconcentration of inorganic Se anions in a wide range of working pHs. Simultaneous retention and elution of both analytes, followed by subsequent analysis with LC-ICP-DRC-MS, allows to accomplish speciation analysis in natural samples without complicated redox pre-treatment. The laboratory-made column of immobilized AC (0.4 g of sorbent packed in a 6 mL syringe barrel) has achieved analyte enrichment factors of 76 and 93, respectively, for Se(IV) and Se(VI), thus proving its superior preconcentration efficiency and selectivity over common AC. The considerable enhancement in sensitivity achieved by using the preconcentration column has improved the method's detection limits to 1.9-2.2 ng L(-1), which is a 100-fold improvement compared with direct injection. The analyte recoveries from heavily polluted river matrix were between 95.3 and 107.7% with less than 5.0% RSD. The robustness of the preconcentration and speciation method was validated by analysis of natural waters collected from rivers and reservoirs in Hong Kong. The modified AC material is hence presented as a low-cost yet robust substitute for conventional anion exchange resins for routine applications.     

Selective extraction, separation and speciation of iron in different samples using 4-acetyl-5-methyl-1-phenyl-1H-pyrazole-3-carboxylic acid

A method for speciation, preconcentration and separation of Fe(II) and Fe(III) in different matrices was developed using solvent extraction and flame atomic absorption spectrometry. 4-Acetyl-5-methyl-1-phenyl-1H-pyrazole-3-carboxylic acid (AMPC) was used as a new complexing reagent for Fe(III). The Fe(III)-AMPC complex was extracted into methyl isobutyl ketone (MIBK) phase in the pH range 1.0-2.5, and Fe(II) ion remained in aqueous phase at all pH. The chemical composition of the Fe(III)-AMPC complex was determined by the Job's method. The optimum conditions for quantitative recovery of Fe(III) were determined as pH 1.5, shaking time of 2 min, 1.64 × 10⁻⁴ mol L⁻¹ AMPC reagent and 10 mL of MIBK. Furthermore, the influences of diverse metal ions were investigated. The level of Fe(II) was calculated by difference of total iron and Fe(III) concentrations. The detection limit based on the 3σ criterion was found to be 0.24 μg L⁻¹ for Fe(III). The recoveries were higher than 95% and relative standard deviation was less than 2.1% (N = 8). The validation of the procedure was performed by the analysis of two certified standard reference materials. The presented method was applied to the determination of Fe(II) and Fe(III) in tap water, lake water, river water, sea water, fruit juice, cola, and molasses samples with satisfactory results.     

Arsenic speciation in natural water samples by coprecipitation-hydride generation atomic absorption spectrometry combination

A speciation procedure for As(III) and As(V) ions in environmental samples has been presented. As(V) was quantitatively recovered on aluminum hydroxide precipitate. After oxidation of As(III) by using dilute KMnO₄, the developed coprecipitation was applied to determination of total arsenic. Arsenic(III) was calculated as the difference between the total arsenic content and As(V) content. The determination of arsenic levels was performed by hydride generation atomic absorption spectrometry (HG-AAS). The analytical conditions for the quantitative recoveries of As(V) including pH, amount of aluminum as carrier element and sample volume, etc. on the presented coprecipitation system were investigated. The effects of some alkaline, earth alkaline, metal ions and also some anions were also examined. Preconcentration factor was calculated as 25. The detection limits (LOD) based on three times sigma of the blank (N: 21) for As(V) was 0.012 μg L⁻¹. The satisfactory results for the analysis of arsenic in NIST SRM 2711 Montana soil and LGC 6010 Hard drinking water certified reference materials for the validation of the method was obtained. The presented procedure was successfully applied to real samples including natural waters for arsenic speciation.     

Voltammetric methods for speciation analysis of trace metals in natural waters

Trace metals play an important role in the regulation of primary productivity and phytoplankton community composition. Metal species directly affects the biogeochemical cycling processes, transport, fate, bioavailability and toxicity of trace metals. Therefore, developing powerful methods for metal speciation analysis is very useful for research in a range of fields, including chemical and environmental analysis. Voltammetric methods, such as anodic stripping voltammetry (ASV) and competing ligand exchange-adsorptive cathodic stripping voltammetry (CLE-AdCSV), have been widely adopted for speciation analysis of metals in different natural aquatic systems. This paper provides an overview of the theory of voltammetric methods and their application for metal speciation analysis in natural waters, with a particular focus on current voltammetric methods for the discrimination of labile/inert fractions, redox species and covalently bound species. Speciation analysis of typical trace metals in natural waters including Fe, Cu, Zn, Cd, and Pb are presented and discussed in detail, with future perspectives for metal speciation analysis using voltammetric methods also discussed. This review can elaborate the particular knowledge of theory, merits, application and future challenge of voltammetric methods for speciation analysis of trace metals in natural waters.     

Applicability of a liquid membrane in enrichment and determination of nickel traces from natural waters

In this work, a bulk liquid membrane method has been applied for Ni enrichment and separation from natural waters. The carrier-mediated transport was accomplished by pyridine-2-acetaldehyde benzoylhydrazone dissolved in toluene as a complexing agent. The preconcentration was achieved through pH control of source and receiving solutions via a counterflow of protons. The main variables were optimized by using a modified simplex technique. High transport efficiencies (101.2 ± 1.8–99.7 ± 4.2%) were provided by the carrier for nickel ions in a receiving phase of 0.31 mol L⁻¹ nitric acid after 9–13 h depending on sample salinity. The precision of the method was 2.05% (without a saline matrix) and 4.04% (with 40 g L⁻¹ NaCl) at the 95% confidence level and the detection limit of the blank was 0.015 μg L⁻¹ Ni for detection by atomic absorption spectroscopy. The applicability of the method was tested on certified reference and real water samples with successful results, even for saline samples. The relative errors were −0.60% for certified reference materials and ranged from −0.39 to 2.90% and from 0.3 to 11.05% for real samples, obtained by comparison of inductively coupled plasma mass spectrometry and adsorptive cathodic stripping voltammetry measurements, respectively.     

Column chromatographic speciation of chromium for Cr(VI) and several species of Cr(III)

Summary Chromium can be present in aqueous solution as Cr(VI) or in monomeric, dimeric, trimeric and higher polymeric forms of Cr(III). Many monomeric forms of Cr(III) are possible, with the water molecules of Cr(H₂O) ₆ ³⁺ substituted by anionic or neutral species. This proliferation of Cr(III) species makes the complete speciation of chromium a continuing challenge to the analyst. A simple and effective cation exchange procedure for the separation of various of these species uses a small glass column containing 1 mL of pre-treated cation exchange resin (Na⁺ form). Stepwise elution with solutions of perchloric acid, Ca²⁺ (pH=2) and La³⁺ (pH=2) separates Cr(VI) and seven Cr(III) species from CrX₃ to tetramer. Radiometric (Cr-51), spectrophotometric and other detection methods can be employed; the use of radiochromium gives the lowest detection limit.     

Studies on phenol permeation through supported liquid membranes containing functionalized polyorganosiloxanes

In this study, the functionalized, linear, hydrophobic fluid organosiloxane polymers, namely, methylhydrosiloxane–dimethylsiloxane copolymers supported on a polypropylene microporous flat sheet membrane (Celgard 2502 and 2402) have been tested as supported liquid membranes (SLMs) for phenol recovery from aqueous phases into a 0.1 M NaOH phase. The functionalized polymers include, Me₃SiO[MeSi(OR)O]_x[Me₂SiO]_ySiMe₃ (containing x = 15–18, 25–35 and 50–55 mol% of R, where R is –(CH₂)_nNMe₂ (n = 3 or 4 or 6) or –(CH₂)₂OEt pendent organofunctional groups. The functionalities, R, tested were derived from the commercially available 3-dimethylamino-1-propanol and 2-ethoxyethanol as well as newly synthesized 4-dimethylamino-1-butanol and 6-dimethylamino-1-hexanol which have been made for the purpose of this study.

The study showed that phenol permeation expressed as permeate flux through the membranes increases with the larger number of carbon spacers in the alkyl chain of the aminoalcohol pendent, larger porosity of the polypropylene support films, higher mol% of the methylhydrosiloxane portion functionalized and faster flow rates of both the feed and the receiving phases. Phenol permeation was enhanced significantly when the mol% of the methylhydrosiloxane portion was 50–55 or 25–35 with 6-dimethylamino-1-hexanol functionality supported on Celgard 2502.