Calculations for shortening the bunch length in storage rings using a harmonic cavity

Using the Hefei Light Source phaseⅡproject(HLS-Ⅱ)as an example,a theoretical analysis of shortening the bunch lengths using a higher harmonic cavity(HHC)is given.The threshold voltage of an active HHC and the threshold tuning angle of a passive HHC are first analysed.The optimum tuning angle for the constant detuning scenario and the optimum harmonic voltage for the constant voltage scenario are presented.The calculated results show that the reduced bunch length is about half that of the nominal bunch.The bunch lengths vary from 11 mm at 0.1 A to 7 mm at 0.4 A for the constant detuning scenario,while the bunch lengths are around 7 mm over the beam current range for the constant voltage scenario.In addition,the synchrotron frequency spread is increased.It indicates that HHC may be used to reduce the bunch length and increase the Landau damping of synchrotron oscillations in a storage ring.     

单谐振腔束团长度监测器的设计与仿真

提出了一种利用单个谐振腔测量直线加速器束团长度的新方法。不同于传统的双谐振腔束团长度监测器,该方法仅需要使用单个谐振腔,省去了用于辅助测量的参考腔,从而简化了装置结构,节省了空间。针对国家同步辐射实验室基于可调谐红外激光的能源化学研究大型实验装置进行了监测器的物理设计。通过设定同轴探针的插入位置,解决了双模信号互相干扰的问题,利用微扰金属改变调节工作频率,克服了双模难以同时谐振的困难。利用CST软件进行建模和仿真。仿真结果表明,该监测器可实现2～5 ps束团长度的诊断,测量误差小于5%。     

合肥光源单束团下束团长度和能散的测量

根据同步光与储存环中的束流信号具有相同的时间结构的原理,测量同步光脉冲的半高全宽值可以计算出束团的长度。根据合肥光源的特点和实际需要,选择快速光电接收器搭配高速高带宽示波器作为在线测量束团长度和纵向分布等的主要手段。对单束团模式下束团长度随流强和高频腔腔压的变化趋势进行了测量。测量结果表明：束团长度与腔压的0.3次方成反比,比理论值0.5小;而束团长度随流强的增长率为2.0 ps/mA。通过测量纵向量子寿命进行了能散随流强变化的间接测量,结果表明,束团的拉伸是能散变化和势阱效应共同作用的结果。     

RF deflecting cavity for bunch length measurement in Tsinghua Thomson scattering X-ray source

An RF deflecting cavity used for bunch length measurement has been designed and fabricated at Tsinghua University for the Thomson Scattering X-Ray Source.The cavity is a 2856 MHz,π-mode,3-cell standing-wave cavity,to diagnose the 3.5 MeV beam produced by photocathode electron gun.With a larger power source,the same cavity will again be used to measure the accelerated beam with energy of 50 MeV before colliding with the laser pulse.The RF design using MAFIA for both the cavity shape and the power coupler is reviewed,followed by presenting the fabrication procedure and bench measurement results of two cavities.     

RF deflecting cavity design for bunch length measurement of photoinjector at Tsinghua University

RF deflecting cavity can be used for bunch length measurement and is designed to diagnose the beam produced by the photocathode electron gun which was built at Tsinghua University for the Thomson scattering experiment. Detailed discussion and calculation for measuring the 3.5 MeV bunch and another with further acceleration to 50 MeV, which is under development, are presented. A standing-wave deflecting cavity working at 2856 MHz is designed and the power feeding system has been planned.     

RF deflecting cavity design for bunch length measurement of photoinjector at Tsinghua University

RF deflecting cavity can be used for bunch length measurement and is designed to diagnose the beam produced by the photocathode electron gun which was built at Tsinghua University for the Thomson scattering experiment.Detailed discussion and calculation for measuring the 3.5 MeV bunch and another with further acceleration to 50 MeV,which is under development,are presented.A standing-wave deflecting cavity working at 2856 MHz is designed and the power feeding system has been planned.     

TM020模式谐振腔束团长度监测器的设计与仿真（英）

提出了一种基于高次模式的谐振腔束团长度测量技术,新方法的谐振腔工作于高次本征模式TM0n0。这样的谐振腔拥有更大的腔体半径,从而移除了谐振腔半径必须大于束流管道半径这一原则带来的工作频率限制。为国家同步辐射实验室未来的正电子源设计了一台双腔束团长度监测器,讨论了谐振腔工作频率的选择并推导了束团长度的计算公式,监测器的谐振腔工作于TM020模式,其半径远大于使用TM010模式的传统方法,在CST软件中模拟的结果显示其束团长度测量精度好于7%。     

Preliminary result of bunch length measurement using a modified Michelson interferometer

Based on the femtosecond accelerator device which was built at the Shanghai Institute of Applied Physics (SINAP), recently a modified far infrared Michelson interferometer has been developed to measure the length of electron bunches via the optical autocorrelation method.Compared with our former normal Michelson interferometer, we use a hollow retroreflector instead of a flat mirror as the reflective mirror.The experimental setup and results of the bunch length measurement will be described in this paper.     

Preliminary result of bunch length measurement using a modified Michelson interferometer

Based on the femtosecond accelerator device which was built at the Shanghai Institute of Applied Physics （SINAP）, recently a modified far infrared Michelson interferometer has been developed to measure the length of electron bunches via the optical autocorrelation method. Compared with our former normal Michelson interferometer, we use a hollow retroreflector instead of a flat mirror as the reflective mirror. The experimental setup and results of the bunch length measurement will be described in this paper.     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime. The higher harmonic cavity of Shanghai Synchrotron Radiation Facility (SSRF) is a 1.5GHz passive superconducting cavity. Its higher order modes (HOM) are extracted by a ferrite HOM damper out of the cryostat. Multi-cell cavity is chosen concerning the voltage. The harmonic cavity dynamics, beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

Investigation on the fabrication of the 3rd harmonic superconducting cavity for the SSRF storage ring

A third harmonic superconducting niobium cavity has been proposed for installation in the Shang-hai Synchrotron Radiation Facility (SSRF) storage ring to improve the Touschek lifetime. In order to investigate the feasibility of the superconducting cavity fabrication indigenously and the possibility to master the fabrica-tion techniques, cavities were fabricated from copper and niobium sheets by deep drawing and electron-beam welding, and a series of measurements, such as resonant frequency, shape dimensions and wall thickness, were carried out during this process. After analysis of various problems existing in the fabrication process, tech-nique improvements were proposed, and finally the precise shape as designed and resonant frequency within 1.2 MHz were achieved for the new completed cavities. In addition, full annealing was finally proved to be a good cure for niobium sheets' tearing up during deep drawing. By fabricating niobium cavities successfully, some problems to the next step were cleared. This paper introduces the process of cavity fabrication and its technique improvements towards forming, and the initial vertical test result of niobium cavity is also presented.     

Investigation on the fabrication of the 3rd harmonic superconducting cavity for the SSRF storage ring

A third harmonic superconducting niobium cavity has been proposed for installation in the Shanghai Synchrotron Radiation Facility （SSRF） storage ring to improve the Touschek lifetime. In order to investigate the feasibility of the superconducting cavity fabrication indigenously and the possibility to master the fabrica tion techniques, cavities were fabricated from copper and niobium sheets by deep drawing and electron-beam welding, and a series of measurements, such as resonant frequency, shape dimensions and wall thickness, were carried out during this process. After analysis of various problems existing in the fabrication process, technique improvements were proposed, and finally the precise shape as designed and resonant frequency within 1.2 MHz were achieved for the new completed cavities. In addition, full annealing was finally proved to be a good cure for niobium sheets＇ tearing up during deep drawing. By fabricating niobium cavities successfully, some problems to the next step were cleared. This paper introduces the process of cavity fabrication and its technique improvements towards forming, and the initial vertical test result of niobium cavity is also presented.     

Study of a magnetic alloy-loaded RF cavity for bunch compression at the CSR

The Heavy Ion Research Facility and Cooling Storage Ring（HIRFL-CSR）accelerator in Lanzhou offers a unique possibility for the generation of high density and short pulse heavy ion beams by non-adiabatic bunch compression longitudinally,which is implemented by a fast jump of the RF-voltage amplitude.For this purpose,an RF cavity with high electric field gradient loaded with Magnetic Alloy cores has been developed.The results show that the resonant frequency range of the single-gap RF cavity is from 1.13 MHz to 1.42 MHz,and a maximum RF voltage of 40 kV with a total length of 100 cm can be obtained,which can be used to compress heavy ion beams of 238U72＋ with 250 MeV/u from the initial bunch length of 200 ns to 50 ns with the coaction of the two single-gap RF cavity mentioned above.     

Study of a magnetic alloy-loaded RF cavity for bunch compression at the CSR

The Heavy Ion Research Facility and Cooling Storage Ring(HIRFL-CSR)accelerator in Lanzhou offers a unique possibility for the generation of high density and short pulse heavy ion beams by non-adiabatic bunch compression longitudinally,which is implemented by a fast jump of the RF-voltage amplitude.For this purpose,an RF cavity with high electric field gradient loaded with Magnetic Alloy cores has been developed.The results show that the resonant frequency range of the single-gap RF cavity is from 1.13 MHz to 1.42 MHz,and a maximum RF voltage of 40 kV with a total length of 100 cm can be obtained,which can be used to compress heavy ion beams of 238U72+ with 250 MeV/u from the initial bunch length of 200 ns to 50 ns with the coaction of the two single-gap RF cavity mentioned above.     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime.The higher harmonic cavity of Shanghai Synchrotron Radiation Facility(SSRF)is a 1.5 GHz passive superconducting cavity.Its higher order modes(HOM)are extracted by a ferrite HOM damper out of the cryostat.Multi-cell cavity is chosen concerning the voltage.The harmonic cavity dynamics,beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

Effect of cavity length detuning on the output characteristics for the middle infrared FEL oscillator of FELiChEM

FELiChEM is an infrared free electron laser(FEL) facility currently under construction, which consists of two oscillators generating middle-infrared and far-infrared laser covering the spectral range of 2.5–200 μm. In this paper, we numerically study the output characteristics of the middle-infrared oscillator with accurate cavity length detuning. Emphasis is put on the temporal structure of the micropulse and the corresponding spectral bandwidth.Taking the radiation wavelengths of 50 μm and 5 μm as examples, we show that the output pulse duration can be tuned in the range of 1–6 ps with corresponding bandwidth of 13%–0.2% by adjusting the cavity length detuning.In addition, a special discussion on the comb structure is presented, and it is indicated that the comb structure may arise in the output optical pulse when the normalized slippage length is much smaller than unity. This work has reference value for the operation of FELiChEM and other FEL oscillators.     

Extension of high-order harmonic cutoff frequency by synthesizing the waveform of a laser field via the optimization of classical electron trajectory in the laser field

We theoretically investigate high-order harmonic generation by employing strong-field approximation （SFA） and present a new approach to the extension of the high-order harmonic cutoff frequency via an exploration of the dependence of high-order harmonic generation on the waveform of laser fields. The dependence is investigated via detailed analysis of the classical trajectories of the ionized electron moving in the continuum in the velocity-position plane. The classical trajectory consists of three sections （Acceleration Away, Deceleration Away, and Acceleration Back）, and their relationship with the electron recollision energy is investigated. The analysis of classical trajectories indicates that, besides the final （Acceleration Back） section, the electron recollision energy also relies on the previous two sections. We simultaneously optimize the waveform in all three sections to increase the electron recollision energy, and an extension of the cutoff frequency up to Ip ＋ 20.26Up is presented with a theoretically synthesized waveform of the laser field.     

Investigation of hypersonic flows through a cavity with sweepback angle in near space using the DSMC method

Near space has been paid more and more attentionin recent years due to its military application value.However,flow characteristics of some fundamental configurations(e.g.,the cavity) in near space have rarely been investigated due to rarefied gas effects,which make the numerical simulation methods based on continuous flow hypothesis lose validity.In this work,the direct simulation Monte Carlo(DSMC),one of the most successful particle simulation methods in treating rarefied gas dynamics,is employed to explore flow characteristics of a hypersonic cavity with sweepback angle in near space by considering a variety of cases,such as the cavity at a wide range of altitudes 20-60 km,the cavity at freestream Mach numbers of 6-20,and the cavity with a sweepback angle of 30°-90°.By analyzing the simulation results,flow characteristics are obtained and meanwhile some interesting phenomena are also found.The primary recirculation region,which occupies the most area of the cavity,causes pressure and temperature stratification due to rotational motion of fluid inside it,whereas the pressure and temperature in the secondary recirculation region,which is a small vortex and locates at the lower left corner of the cavity,change slightly due to low-speed movement of fluid inside it.With the increase of altitude,both the primary and secondary recirculation regions contract greatly and it causes them to separate.A notable finding is that rotation direction of the secondary recirculation region would be reversed at a higher altitude.The overall effect of increasing the Mach number is that the velocity,pressure,and temperature within the cavity increase uniformly.The maximum pressure nearby the trailing edge of the cavity decreases rapidly as the sweepback angle increases,whereas the influence of sweepback angle on velocity distribution and maximum temperature within the cavity is slight.