Design and simulation of a beam position monitor for the high current proton linac

In this paper, the 2-D electrostatic field software, POISSON, is used to calculate the characteristic impedance of a BPM （beam position monitor） for a high current proton linac. Furthermore, the time-domain 3-D module of MAFIA with a beam microbunch at a varying offset from the axis is used to compute the induced voltage on the electrodes as a function of time. Finally, the effect of low β beams on the induced voltage, the sensitivity and the signal dynamic range of the BPM are discussed.     

Homogeneous interface-type resistance switching in Au/La0.67Ca0.33MnO3/SrTiO3/F:SnO2 heterojunction memories

La0.67Ca0.33MnO3 thin films are fabricated on fluorine-doped tin oxide conducting glass substrates by a pulsed laser deposition technique with SrTiO3 used as a buffer layer. The current-voltage characteristics of the heterojunetions exhibit an asymmetric and resistance switching behaviour. A homogeneous interface-type conduction mechanism is also reported using impedance spectroscopy. The spatial homogeneity of the charge carrier distribution leads to field- induced potential-barrier change at the Au-La0.67Ca0.33MnO3 interface and a concomitant resistance switching effect. The ratio of the high resistance state to the low resistance state is found to be as high as 1.3 x 10^4% by simulating the AC electric field. This colossal resistance switching effect will greatly improve the signal-to-noise ratio in nonvolatile memory applications.     

New test and analysis of position-sensitive-silicon-detector

We have tested and analyzed the properties of two-dimensional Position-Sensitive-silicon-Detector （PSD） with new integrated preamplifiers. The test demonstrates that the best position resolution for 5.5 MeV α particles is 1.7 mm （FWHM）, and the best energy resolution is 2.1%, which are notably better than the previously reported results. A scaling formula is introduced to make the absolute position calibration.     

Study of a multi-wire proportional chamber with a cathode strip and delay-line readout

The design principle for a multi-wire proportional chamber with a cathode strip and delay-line readout is described. A prototype chamber of a size of 10 cm×10 cm was made together with the readout electronics circuit. A very clean signal with very low background noise was obtained by applying a transformer between the delay-line and the pre-amplifier in order to match the resistance. Along the anode wire direction a position resolution of less than 0.5 mm was achieved with a ^55Fe-5.9 keV X ray source. The simple structure, large effective area and high position resolution allow the application of a gas chamber of this kind to many purposes.     

Conditioning of BPM pickup signals for operations of the Duke storage ring with a wide range of single-bunch current

The Duke storage ring is a dedicated driver for the storage ring based oscillator free-electron lasers（FELs）, and the High Intensity Gamma-ray Source（HIGS）. It is operated with a beam current ranging from about1 mA to 100 mA per bunch for various operations and accelerator physics studies. High performance operations of the FEL and γ-ray source require a stable electron beam orbit, which has been realized by the global orbit feedback system. As a critical part of the orbit feedback system, the electron beam position monitors（BPMs） are required to be able to precisely measure the electron beam orbit in a wide range of the single-bunch current. However, the high peak voltage of the BPM pickups associated with high single-bunch current degrades the performance of the BPM electronics, and can potentially damage the BPM electronics. A signal conditioning method using low pass filters is developed to reduce the peak voltage to protect the BPM electronics, and to make the BPMs capable of working with a wide range of single-bunch current. Simulations and electron beam based tests are performed. The results show that the Duke storage ring BPM system is capable of providing precise orbit measurements to ensure highly stable FEL and HIGS operations.     

Preliminary application of turn-by-turn data analysis to the SSRF storage ring

There is growing interest in utilizing the beam position monitor turn-by-turn（TBT） data to debug accelerators. TBT data can be used to determine the linear optics,coupled optics and nonlinear behaviors of the storage ring lattice. This is not only a useful complement to other methods of determining the linear optics such as LOCO,but also provides a possibility to uncover more hidden phenomena. In this paper,a preliminary application of a β function measurement to the SSRF storage ring is presented.     

Asymptotic Iteration Method for Energies of Inversely Linear Potential with Spatially Dependent Mass

The bound-state solution of the position dependent mass Klein-Gordon equation including inversely linear potential is obtained within the framework of the asymptotic iteration method. The relation between the scalar and vector potentials is considered to S（x） = V（x）（β - 1）. In particular, it is shown that the corresponding method exactly reproduces the spectrum of linearly inversely potentials with spatially dependent mass.     

140 GHz带状注弯折波导SU-8工艺与传输特性(英)

对140 GHz 带状注弯折波导的色散特性和耦合阻抗进行了仿真。CST微波工作室的仿真表明该波导在140 GHz时,波导内电磁波的轴向相速度为0.227c,且140 GHz频率附近色散特性平坦。波导的耦合阻抗在140 GHz时为5 左右。CST粒子工作室注波互作用的仿真结果表明该弯折波导在140 GHz处的功率增益为24.6 dB。该弯折波导带状电子注的设计保证了该波导的加工工艺与MEMS微加工工艺兼容。通过SU-8 UV-LIGA工艺实现了对该波导的微型加工。测试结果表明该波导的反射损耗S11与插入损耗S21分别为-28 dB和-1.2 dB。实测的输出功率增益达到23 dB。测试结果和仿真结果的一致性表明该弯折波导设计的合理性,同时也验证了多步SU-8 UV-LIGA工艺可以实现对该波导的高精度加工。     

Study of a rectangular coupled cavity extendedinteraction oscillator in sub-terahertz waves

An extended interaction oscillator （EIO） generating 120 GHz wave in sub-terahertz waves is studied by using the three-dimensional electromagnetic simulation software CST and PIC codes. A rectangular reentrant coupled-cavity is proposed as the slow-wave structure of EIO. By CST, the circuit parameters including frequency-phase dispersion, interaction impedance and characteristic impedance are simulated and calculated. The operation mode of EIO is chosen very close to the point where βL = 2π with corresponding frequency 120 GHz, the beam voltage 12 kV and the dimensions of the cavity with the period 0.5mm, the height 3mm and the width 1.4mm. Simulation results of beam-wave interaction by PIC show that the exciting frequency is 120.85 GHz and output peak power 465 W with 12-period coupled-cavity with the perveance 0.17 μP. Simulation results indicate that the EIO has very wide range of the operation voltage.     

Remarks on interpretations of the Eotvos experiment and misinterpretation of E=mc^2

The Eotvos experiment on the verification of equivalence between inertial mass and gravitational mass of a body is famous for its accuracy. A question is, however, can these experimental results be applied to the case of a physical space in general relativity, where the space coordinates could be arbitrary？ It is pointed out that it can be validly applied because it has been proven that Einstein＇s equivalence principle for a physical space must have a frame of reference with the Euclidean-like structure. Will claimed further that such an overall accuracy can be translated into an accuracy of the equivalence between inertial mass and each type of energy. It is shown that, according to general relativity, such a claim is incorrect. The root of this problem is due to an inadequate understanding of special relativity that produced the famous equation E=mc^2, which must be understood in terms of energy conservation. Concurrently, it is pointed out that this error is a problem in Will＇s book, ‘Theory and Experiment in Gravitational Physics＇.     

First-Principles Calculations of Atomic and Electronic Properties of T1 and In on Si（111）

The atomic and electronic structures of T1 and In on Si（111） surfaces are investigated using the firstprinciples total energy calculations. Total energy optimizations show that the energetically favored structure is 1/3 ML T1 adsorbed at the T4 sites on Si（111） surfaces. The adsorption energy difference of one T1 adatom between （√3 × √3） and （1 × 1） is less than that of each In adatom. The DOS indicates that TI 6p and Si 3p electrons play a very important role in the formation of the surface states. It is concluded that the bonding of TI adatoms on Si（111） surfaces is mainly polar covalent, which is weaker than that of In on Si（111）. So T1 atom is more easy to be migrated than In atom in the same external electric field and the structures of T1 on Si（111） is prone to switch between （√3 × √3） and （1 × 1）.     

Ca0.5Sr0.5TiO3弹性和热学性质的第一性原理研究

利用能量最小原理, 确定了Ca_0.5Sr_0.5TiO₃晶体中4c位置的Ca/Sr原子对称分布, 建立了Ca_0.5Sr_0.5TiO₃稳定的晶体结构, 在此基础上利用基于密度泛函理论第一性原理的平面波超软赝势方法, 采用局域密度近似和广义梯度近似函数, 计算了Ca_0.5Sr_0.5TiO₃的晶格参数、弹性常数、体弹模量、剪切模量、杨氏模量、泊松比, 并基于Christoffel方程的本征值研究了平面声波的特征, 基于Cahill和Cahill-Pohl模型研究了最小热导率的特征. 计算结果表明: Ca_0.5Sr_0.5TiO₃晶格参数和实验值很接近, 体弹模量大于剪切模量, [100], [010], [001]晶向的杨氏模量、泊松比、普适弹性常数(A^U)以及杨氏模量三维图均显示了弹性各向异性; 平面声波在(010), (001)平面呈现各向异性, 在(100)平面呈现各向同性, 平面声波大小与平均横波和平均纵波的数值很接近. Cahill模型最小热导率在各平面呈现各向同性, Cahill-Pohl模型最小热导率在高温时趋于恒定. 准谐德拜模型下Ca_0.5Sr_0.5TiO₃ 晶体的摩尔热容和热膨胀系数与CaTiO₃晶体的接近, 并且高温下具有稳定的热膨胀性能. 计算所得禁带宽度为2.19 eV, 导带底主要是Ti-3d与O-2p态电子贡献; 由电荷布居和电荷密度图理论证实Ca_0.5Sr_0.5TiO₃具有稳定的Ti-O八面体结构.     

Study on the pre-chopper in CSNS LEBT

Physical designing of the pre-chopper in CSNS LEBT is carried out, which includes the deflecting voltage, the length and the width of the deflecting plates, and the gap between the deflecting plates. The most outstanding feature of the design is that both the gap and the width vary with the beam envelope size. So both the requried deflecting voltage and the loaded capacitance are lowered. In order to avoid destruction of the space charge neutralization by the pre-chopper in the whole LEBT, an electron-trapping electrode is arranged to confine the electrostatic field of the pre-chopper to the local area. To examine the reliability of the pre-chopping design in CSNS LEBT, a similar pre-chopping design in ADS RFQ LEBT is set up and an experiment on the pre-chopper is prepared. 3-dimensional simulations are carried out to determine the loaded capacitance and the applied voltage of the electron-trapping electrode.     

Entropy of Quantum Dynamical Systems and Sufficient Families in Orthomodular Lattices with Bayessian State

The purpose of the present paper is to study the entropy hs（Ф） of a quantum dynamical systems Ф = （ L, s, Ф）, where s is a bayessian state on an orthomodular lattice L. Having introduced the notion of entropy hs（ Ф, A） of partition A of a Boolean algebra B with respect to a state s and a state preserving homomorphism Ф, we prove a few results on that, define the entropy of a dynamical system hs（Ф）, and show its invariance. The concept of sufficient families is also given and we establish that hs （Ф） comes out to be equal to the supremum of hs （Ф,A）, where A varies over any sufficient family. The present theory has then been extended to the quantum dynamical system （ L, s, Ф）, which as an effect of the theory of commutators and Bell inequalities can equivalently be replaced by the dynamical system （B, s0, Ф）, where B is a Boolean algebra and so is a state on B.     

Synchronization in a Mutualism Ecosystem Induced by Noise Correlation

Understanding the cause of the synchronization of population evolution is an important issue for ecological improvement. Here we present a Lotka-Volterra-type model driven by two correlated environmental noises and show, via theoretical analysis and direct simulation, that noise correlation can induce a synchronization of the mutualists. The time series of mutual species exhibit a chaotic-like fluctuation, which is independent of the noise correlation, however, the chaotic fluctuation of mutual species ratio decreases with the noise correlation. A quantitative parameter defined for characterizing chaotic fluctuation provides a good approach to measure when the complete synchronization happens.     

Metric of States

Metric of quantum states plays an important role in quantum information theory. In this letter, we find the deep connection between quantum logic theory and quantum information theory. Using the method of quantum logic, we can get a famous inequality in quantum information theory, and we answer a question raised by S. Gudder.     

Status and accuracy of the Monte Carlo generators for luminosity measurements

The status and accuracy of the precision Monte Carlo generators used for luminosity measurements at flavour factories is reviewed. It is shown that, thanks to a considerable, long-term effort in tuned comparisons between the predictions of independent programs, as well as in the validation of the generators against the presently available calculations of the next-to-next-to-leading order QED corrections to Bhabha scattering, the theoretical accuracy reached by the most precise tools is of about one per mille. This error estimate is valid for realistic experimental cuts, appears to be quite robust and is already sufficient for very accurate luminosity measurements. However, recent progress and possible advances to further improve it are also discussed.     

Beam tail effect of a performance-enhanced EC-ITC RF gun

The beam tail effect of multi-bunches will influence the electron beam performance in a high intensity thermionic RF gun. Beam dynamic calculations that illustrate the working states of single beam tail and multi-pulse feed-in of a performance-enhanced EC-ITC （external cathode independent tunable cavity） RF gun for an FEL （free electron laser） injector are performed to estimate the extracted bunch properties. By using both Parmela and homemade MATLAB codes, the effects of a single beam tail as well as interactions of multi-pulses are analyzed, where a ring-based electron algorithm is adopted to calculated RF fields and the space-charge field. Furthermore, the procedure of unexpected deviated-energy particles mixed with an effective bunch head is described by the MATLAB code as well. As a result, the performance-enhanced EC-ITC RF gun is proved to have the capability to extract continual stable bunches suitable for a high requirement THz-FEL.     

D^0D^0 mixing and other recent charm results from BABAR

Studies in which BABAR data have shown evidence for mixing in the neutral charm meson system are presented. A new measurement of the lifetime difference parameter ycp = （1.16±0.22±0.18）% is described. Results are also presented from a systematic study of DK and D＊K invariant mass distributions from a 470 fb^-1 sample of asymmetric e^＋e^- interactions recorded by the BABAR detector at the PEP-Ⅱ storage rings. A new charmed-strange meson has been observed with mass [3044 ± 8stat （-5^＋30 ）syst] MeV/c^2 and width [239± 35stat （-42^＋46）syst]MeV/c^2.     

Coordinated Control of Multi-Agent Systems with a Varying-Velocity Leader and Input Saturation

In this paper, we investigate a leader-following tracking problem for multi-agent systems with bounded inputs. We propose a distributed bounded protocol for each follower to track a leader whose states may not be completely measured. We theoretically prove that each agent can follow the leader with estimable track errors. Finally, some numerical simulations are presented to illustrate our theoretical results.