超高压和酶抑制剂联合处理对荔枝果肉中过氧化物酶和果胶甲基酯酶的影响

 为了研究超高压与酶抑制剂联合处理对荔枝果肉中过氧化物酶（POD）和果胶甲基酯酶（PME）的影响,将荔枝（“淮枝”品种）果肉在两种酶抑制剂组合溶液（A：5 g/L柠檬酸+2.5 g/L L-抗坏血酸+5 g/L氯化钙;B：10 g/L柠檬酸+5 g/L L-抗坏血酸+10 g/L氯化钙）中分别浸泡10 min,并在100~400 MPa压力、10 ℃温度条件下处理30 min,采用分光光度法测定果肉中POD、PME的活性。结果表明：A、B两种组合处理能够明显钝化POD,但却显著激活了PME;超高压与A组合联合处理不能使POD、PME活性下降;超高压与B组合联合处理对POD、PME的影响与压力值有关系,100~300 MPa的超高压与B组合联合处理使POD活性下降,200~400 MPa的超高压与B组合联合处理则使PME活性升高。因此,超高压与酶抑制剂联合处理对荔枝果肉中POD的钝化存在一定的协同效应,且浓度越高,协同抑制效应越明显;而超高压与酶抑制剂联合处理对荔枝果肉中PME的钝化却表现出一定的拮抗性。     

超高压处理对荔枝果肉中两种酶和可溶性蛋白的影响

 为了研究超高压处理对荔枝果肉中过氧化物酶（POD）、果胶甲基酯酶（PME）及可溶性蛋白含量的影响,将荔枝（“淮枝”品种）果肉在100~400 MPa压力、10 ℃温度条件下处理30 min,采用分光光度法测定果肉中POD、PME的活性,用天然凝胶电泳法以及活性染色法测定POD、PME同工酶的变化,用SDS凝胶电泳法测定果肉中可溶性蛋白含量。结果表明：100~200 MPa超高压处理使荔枝果肉中POD活性上升且出现新的同工酶,300~400 MPa超高压处理则使其活性降低且新出现的同工酶消失;100 MPa压力处理使荔枝果肉中PME活性上升且出现新的同工酶,200~400 MPa超高压处理则使其活性降低且新出现的同工酶消失;100 MPa超高压处理使荔枝果肉中可溶性蛋白含量有所增加,而在200~400 MPa压力处理下其含量持续下降。     

超高压处理对海参自溶酶活性影响的研究

 海参的超高压处理与传统的处理方法相比有许多优越性,具有十分广阔的应用前景。研究了超高压处理过程中压力（0.1~550 MPa）、保压时间（0~30 min）、温度（24~62 ℃）及保压方式对海参自溶酶活性的影响。在室温、保压20 min的条件下,200 MPa左右较低压力下酶活性降低,相对残存活性为88.25%;250 MPa较高压力下自溶酶被激活,酶活性为106.77%;550 MPa高压下酶活性最低为29.81%。自溶酶活性随保压时间和温度的增加先上升后下降;保压方式对自溶酶活性的影响不大。同时利用误差反向传播神经网络（Back Propagation Neural Network,BP人工神经网络）,模拟了超高压钝酶效果,与实验结果比较,平均相对误差为0.9%,可以获得较好的预测结果。研究结果表明,在一定的压力、保压时间和温度下,酶被激活,其活性上升;而在一定的压力、保压时间和温度下,酶被钝化,活性降低。对优化海参超高压钝酶工艺具有一定的参考价值。     

温压协同处理黑莓β-葡萄糖苷酶失活动力学研究

 以黑莓β-葡萄糖苷酶为对象,研究其温压协同条件下的失活动力学规律,可为超高压食品处理技术的工业化和花色苷的保留提供有力的技术支持。实验压力为300~600 MPa,温度为35~55 ℃。结果表明：β-葡萄糖苷酶在温压协同条件下的失活过程为两个阶段,第一阶段用瞬时失活值描述,压力和温度影响其大小,不受保压时间影响;第二阶段将β-葡萄糖苷酶分为稳定部分和敏感部分,β-葡萄糖苷酶的失活过程用双相一级反应动力学模型描述,其失活速率常数随温度、压力的升高而增大。敏感部分和稳定部分在400 MPa、55 ℃条件下,失活速率常数K_L和K_S分别为2.777和0.047 min^-1,二者失活90%所需时间D_L和D_S分别为0.83和49.1 min。在400 MPa条件下,敏感部分的D值减少90%所需增加的温度T_Z和活化能E_a分别为23.36 ℃和81.95 kJ/mol;在45 ℃条件下D值减少90%所需增加的压力p_Z和活化体积V_a分别为1 111 MPa和-5.02 cm³/mol。     

高压与加热协同处理对牛肌肉中蛋白酶活性的影响

在不同温度(20～60℃)和压力(0.1～600 MPa)下处理20 min,对牛肌肉中蛋白酶活性的影响进行了研究.结果显示:室温下,随着处理压力的增加,酶的活力显著下降,而压力达400 MPa及以上时,酶的活力则没有明显变化,同时在pH值为3和7.5时酶的活性几乎完全丧失.200 MPa以下的压力处理使肌肉中游离氨基...     

金属离子辅助高静压钝化树莓多酚氧化酶研究

 树莓多酚氧化酶具有较强的耐压性,在600 MPa压力下处理45 min,其残余酶活仍高达40%以上。为了进一步钝化树莓内源多酚氧化酶的活性,研究了金属离子辅助高静压对树莓多酚氧化酶钝化的影响。在树莓多酚氧化酶粗酶液中添加对酶活性有抑制、激活、无改变的金属离子,研究其辅助400、600 MPa压力处理钝化树莓多酚氧化酶的效果。发现添加金属离子后,多酚氧化酶的活性随压力增大、时间延长而降低;Fe²⁺、Mn²⁺以及Cu²⁺均有不同程度的协同高静压钝化作用,而Ca²⁺在钝化树莓多酚氧化酶时与高静压出现拮抗现象,对树莓多酚氧化酶活性无影响的Zn²⁺未出现协同/拮抗作用。     

超高压处理对多酚氧化酶活性的影响

 研究了超高压中温协同处理对砀山梨汁中多酚氧化酶活性的影响,实验压力为0.1~500 MPa,温度为20~60 ℃。此外,考察了不同pH值（3~7）和保压时间（2~34 min）超高压处理对酶活性的影响。实验结果分析表明：在处理温度为50 ℃、保压时间为10 min和梨汁pH值为5的条件下,200~300 MPa处理梨汁时多酚氧化酶被激活,活性表现最高;500 MPa时酶的活性下降到75.3%。协同温度为30 ℃处理梨汁时,酶的活性反而增大;30 ℃以后,酶活性随温度升高而迅速降低;有效协同高压处理的温度为40 ℃。随着保压时间的延长,梨汁中过氧化物酶的活性减小;18 min以前下降速度较快些,之后下降速度变缓。pH在5~6之间,酶的残留活性最大;pH值为6时,梨汁中多酚氧化酶最为耐压。     

高压处理对辣根过氧化物酶活性及构象的影响

 高压处理对果蔬过氧化物酶活性的钝化程度会影响果蔬的感官品质和贮藏期,有必要研究高压条件下过氧化物酶的结构变化与其活性的关系。采用圆二色谱法和荧光光谱法,研究了室温下,100、300、500 MPa压力分别处理15 min对辣根过氧化物酶二级、三级结构及活性的影响。结果表明：高压处理对辣根过氧化物酶（HRP）有钝化作用,随着处理压力的增加,HRP的活性依次下降2.36%、5.69%、10.36%,HRP较耐压;HRP的α-螺旋、β-折叠和无规卷曲含量的升幅均小于4%,β-转角含量显著下降,且下降程度均达到11%;高压处理后的HRP在234 nm激发光谱和308 nm发射光谱特征峰的荧光强度下降,下降程度依次为18.28%、5.46%和4.04%,且100 MPa压力下处理的HRP荧光强度下降的程度最大。说明高压处理对HRP有钝化作用,且与其二级和三级结构的变化有关。     

超高压均质技术在鲜榨果蔬汁加工中应用的研究进展北大核心CSCD

鲜榨果蔬汁富含维生素C、酚类等活性物质。超高压均质技术是基于传统均质技术发展起来的一种非热加工技术,压力最高可达400MPa,能在常温或较低温度下达到杀菌、钝酶等效果。将超高压均质技术应用于鲜榨果蔬汁的加工,可最大限度地保留鲜榨果蔬汁的原有品质。综述了超高压均质处理对鲜榨果蔬汁中微生物、酶及品质影响的研究进展,讨论了超高压均质技术在鲜榨果蔬汁加工中的应用前景。     

HPCD脱除紫甘蓝色素中烯丙基异硫氰酸酯工艺的优化北大核心CSCD

在紫甘蓝色素提取过程中,由于硫代葡萄糖苷酶解产物烯丙基异硫氰酸酯(AITC)的产生,导致紫甘蓝色素提取液有不良风味,从而限制了它在食品工业上的应用。因此研究新型的高压二氧化碳(HPCD)技术脱除AITC工艺,分别考察了5种水平的压强、温度、处理时间和卸压时间对HPCD脱除AITC效果的影响。通过单因素实验和正交实验确定了HPCD脱除AITC的最佳工艺组合为:温度50℃,处理时间60min,卸压时间2min。在最佳条件下经HPCD处理后,紫甘蓝色素的风味物质种类由17种减至7种,许多异味物质得到不同程度的脱除,其中异味核心物质AITC的质量分数由3.15%减少至1.06%,达到较好的异味脱除效果。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Optical Pulse Compression Schemes That Use Nonlinear Bragg Gratings

Nonlinear optical pulse compression of picosecond pulses typically requires long lengths of optical fiber and multiple components. Periodic structures, such as fiber Bragg gratings, are highly dispersive at wavelengths outside of the photonic bandgap. This implies that such gratings can be used as very short all-fiber compressors. In this paper a number of such compression schemes are reviewed involving uniform and nonuniform fiber Bragg gratings, relying on both soliton and nonsoliton compression principles. Experimental results supporting the corresponding underlying theory are also presented. Finally, an extension of one of the compression schemes is shown, which allows the generation of adjustable high-repetition rate soliton trains.