邻甲酚在类水滑石、焙烧及改性类水滑石上的吸附

用液相非稳态共沉淀法制备了Mg-Al 类水滑石(HTlc); Mg-Al HTlc 于450 ℃下焙烧得焙烧类水滑石(CHTlc); 采用结构重建法由CHTlc 制备了十二烷基硫酸根(DS－)插层(改性)类水滑石(DS·HTlc). 研究了邻甲酚在Mg-Al HTlc,CHTlc 和DS·HTlc 上的吸附行为: 邻甲酚在Mg-Al HTlc, CHTlc 和DS·HTlc 上的吸附动力学和等温式均分别符合准二级动力学方程和Freundlich 方程, 且吸附速率和吸附量大小均依次为: DS·HTlc>>CHTlc>HTlc; 在初始pH＝5.00～13.00 范围内, 邻甲酚在HTlc 和CHTlc 上的吸附量随pH 值的增加先增加后减小, 随温度的增加而增加, 邻甲酚在DS·HTlc 的吸附量随pH 值和温度的增加而降低; 邻甲酚在HTlc, CHTlc 和DS·HTlc 上的吸附量均随电解质(NaCl)浓度的增加而增加, 探讨了吸附机理. 研究结果表明, DS·HTlc 有望成为一种新型的高效酚类有机污染物处理剂.     

水滑石阻燃剂的离子改性研究进展

由于水滑石具有层板阳离子可调控、层间阴离子可交换、酸碱性等独特的性能,在医药、离子交换、催化、材料阻燃等领域备受研究者关注。特别是水滑石用作阻燃材料时,具有无卤、无毒、不产生有毒和腐蚀性气体、阻燃和抑烟性能优良等突出优点,已成为当前材料阻燃领域研究的热点。然而,水滑石也存在热稳定性较差、容易聚集、分散性较差等缺点,故国内外学者开展了水滑石阻燃剂改性的系列研究。本文阐述了近年来利用Ca~(2+)、Mg~(2+)、Al~(3+)等阳离子以及BO_3~(3-)、SiO_3~(2-)等阴离子对水滑石阻燃剂进行改性等方面的研究进展,并对水滑石在生物质材料阻燃、低成本水滑石阻燃剂的合成、水滑石协效阻燃剂的研究、水滑石阻燃剂工业化生产新工艺与设备、洁净化制备技术等方面的研究与应用前景进行了展望。     

超声波作用下离子交换改性水滑石对PP性能的影响

采用超声波离子改性水滑石,并将其添加在等规聚丙烯材料中。运用X射线衍射仪技术(XRD)、傅里叶红外光谱(ATIR)、差示扫描量热(DSC)、偏光显微镜(POM)、扫描电镜(SEM)等方法测试表征了水滑石通过超声离子改性前后对等规聚丙烯材料结构的影响。结果表明,超声离子改性的水滑石能扩大水滑石层间距,促进和增加改性基团的插层率,能改善其在等规聚丙烯中的分散性,对等规聚丙烯起到明显的异相成核作用,细化其晶粒,同时能够增强和增韧等规聚丙烯材料。     

谷氨酸插层水滑石吸附水中铅离子

采用共沉淀法合成了谷氨酸插层镁铝类水滑石(LDH),对所制备的试样进行了X-射线衍射和红外光谱表征,对LDH去除水中铅离子的能力进行了讨论,研究了吸附过程的吸附动力学和吸附等温线。结果表明,谷氨酸能嵌入镁铝水滑石的层间,该插层水滑石能有效吸附水中铅离子,吸附过程符合准二级动力学模型,吸附等温曲线可用Langmuir模型来描述,吸附量可达68.49mg/g。     

水滑石改性二氧化硅新材料去除养殖用水中的孔雀石绿及结晶紫

合成了水滑石改性的系列硅胶新材料HTS-n(s),该新材料同时包含有酸性位与碱性位,并通过碱腐蚀获得了3～4 nm的小孔和大的比表面积。该类材料可选择性吸附去除水产养殖用水中的工业染料类污染物孔雀石绿和结晶紫。吸附后水中剩余的染料浓度通过高效液相色谱-质谱/质谱联用仪进行检测,结果显示新材料的吸附性能超过常用的工业吸附剂NaY沸石和活性炭。     

钾对镁铝水滑石复合氧化物的表面改性

利用X射线衍射(XRD), X射线光电子能谱(XPS), 原位红外(in situ IR)光谱和CO2程序升温脱附(CO2-TPD)等技术研究了K对Mg-Al水滑石复合氧化物(MgAlO)的表面改性. 结果表明, 当K负载量臆8%(w)时, K高度分散在MgAlO表面, 并与载体作用形成了新的Lewis碱位. 其中, K取代MgAlO弱碱位OH上的质子形成弱碱性的Mg(Al)-O-K; 与强碱位表面O2-结合形成强碱性的Mg-O-K. 当K负载量为5%-8%(w)时, 还存在与载体作用较弱并具有更强碱性的准自由KOx. K增强MgAlO碱性的本质是K的电荷转移到了表面氧负离子上.     

F改性CuNiAl水滑石选择性催化氧化甲苯生成苯甲醇

利用水滑石的"记忆效应"将F离子引到铜镍铝水滑石的层板上,并在甲苯的氧化反应中测试其催化性能,运用FTIR、X射线固体粉末衍射技术对其进行了表征,结果表明,引入F离子后的铜镍铝水滑石仍具有良好的层状结构,并表现出了优良的催化活性.在最佳反应条件下,甲苯的转化率最高可达8.4%,苯甲醇的选择性为81.4%.     

聚丙烯/插层改性水滑石纳米复合材料结构与性能研究

采用离子交换法制备了十二烷基磺酸钠和衣康酸共同改性水滑石(LDHs2),FTIR、XRD分析表明,十二烷基磺酸钠和衣康酸能够同时进入水滑石片层之间,层间距有很大提高。利用改性水滑石,通过马来酸酐-苯乙烯共接枝改性聚丙烯相容剂的熔融共混和聚丙烯与水滑石溶液共混制备母粒,然后与聚丙烯分别熔融共混两种方法制备聚丙烯/水滑石纳米复合材料。TEM分析表明,马来酸酐-苯乙烯共接枝改性聚丙烯作相容剂可以使水滑石在聚丙烯基体中达到更好分散。DSC、XRD分析表明,水滑石、相容剂以及短链共聚聚丙烯对聚丙烯晶型没有影响,但对其结晶速率、结晶度以及晶粒大小有所改变,复合材料中聚丙烯的起始结晶温度、结晶峰温度、结晶速率、结晶度均比纯聚丙烯高,晶粒粒径分布也更均匀。     

碳酸钾修饰水滑石吸附二氧化碳工艺条件研究

采用共沉淀法合成水滑石,等体积浸渍法将碳酸钾负载于水滑石孔道及层状结构中;在一定空速条件下,考察了吸附温度、碳酸钾添加量、活化温度对碳酸钾修饰水滑石吸附二氧化碳性能的影响;利用SEM、BET等手段对修饰后的水滑石进行了表征。在一定实验条件下,水滑石吸附容量可以达到9.10mol/kg。     

镁铝型水滑石水热合成

水滑石是一类具有特殊结构的层状无机材料 .具有可调变的组成及独特的结构和性能 ,在离子交换、吸附分离、催化、医药等领域得到广泛应用 [1～ 4 ] .特别是水滑石类材料所具有的选择性、红外吸收性和离子交换性等一些特殊性能 ,使其作为新型无机功能材料已应用于 PE农膜 (保温剂 )和 PVC(无毒热稳定剂 )等高分子材料中 ,显示了独特的性能[5] .作为无机功能材料 ,水滑石在复合材料中的应用必然涉及其粒子尺寸和分布 ,因此对水滑石晶化规律的研究非常重要 .水滑石成熟的合成方法是共沉淀法[6] ,如单滴法、双滴法 .由于沉淀粒子是渐次产生 ,…     

Flammability characteristics and flame retardant mechanism of phosphate-intercalated hydrotalcite in halogen-free flame retardant EVA blends

The flammability characteristics and flame retardant mechanism of phosphate-intercalated hydrotalcite (MgAl-PO₄) in the halogen-free flame retardant ethylene vinyl acetate (EVA) blends have been studied by X-ray diffraction (XRD), Fourier transfer infrared (FTIR) spectroscopy, cone calorimeter test (CCT), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), limiting oxygen index (LOI) and UL-94 tests. The results show that the hydrotalcite MgAl-PO₄ intercalated by phosphate possesses the enhanced thermal stability and flame retardant properties compared with ordinary carbonate-intercalated hydrotalcite MgAl-CO₃ in the EVA blends. The CCT tests indicate that the heat release rate (HRR) and mass loss rate (MLR) values of the EVA/MgAl-PO₄ samples are much lower than those of the EVA/MgAl-CO₃ samples. The TGA data show that the thermal degradation rates of MgAl-PO₄ and EVA/MgAl-PO₄ samples are much slower and leave more charred residues than those of MgAl-CO₃ and its corresponding EVA blends. The LOI values of EVA/MgAl-PO₄ samples are 2% higher than those of the corresponding EVA/MgAl-CO₃ samples at the range of 40–60 wt% loadings, while the EVA sample with 55 wt% MgAl-PO₄ can reach the UL-94 V-1 rating. The dynamic FTIR spectra reveal that the flame retardant mechanism of MgAl-PO₄ can be ascribed to its catalysis degradation of the EVA resin, which promotes the formation of charred layers with the P–O–P and P–O–C complexes in the condensed phase. The SEM observations give further evidence of this mechanism that the compact charred layers formed from the EVA/MgAl-PO₄ sample effectively protect the underlying polymer from burning.     

Thermal stabilities and flame retardancies of nitrogen-phosphorus flame retardants based on bisphosphoramidates

Various nitrogen-phosphorus (P-N) compounds based on phosphoramidate were synthesized as model compounds to investigate the relationships among the chemical structure of linker connecting diphenylphoryl groups between the phosphoramidates, the N content, thermal stability, and flame-retarding ability. The flame-retarding efficiencies were evaluated by the limiting oxygen index (LOI) and UL-94 vertical test methods. It was found that bisphosphoramidates are more thermally stable and produce more charred residues when compared to the corresponding bisphosphate compounds. Aromatic phosphoramidates show fairly good flame retardancy for PC and UL-94 V-0 ratings are achieved with addition of as small amount as 3-5 wt%. However, no rating is found for ABS at 30 wt% loading of bisphosphoramidate FRs which leave the remarkably high residues at 600 °C. The thermogravimetric analysis (TGA) results indicate that these compounds work in condensed phase rather than in gas phase. The effect of chemical structure of linker on the flame retardancy is also discussed.     

Novel phosphorus-silicon synergistic flame retardants:Synthesis and characterization

Three novel flame retardants containing both phosphorus and silicon elements in their structures,including[（1,1,3,3- tetramethyl-1,3-disiloxanediyl）di-2,1-ethanediyl]bis（diphenylphosphine oxide）（FR-1）,[（2,4,6,8-tetramethylcyclotetra-siloxane -2,4,6,8-tetrayl）tetra-2,1-ethanediyl]tetrakis[diphenylphosphine oxide]（FR-2） and 1,3,5,7,9,11,13,15-octakis（di-phenylphosphine oxide-2,1-ethanediyl）pentacyclo[9.5.1.1^3,9.l^5,15.1^7,13]octasiloxane（FR-3） were synthesized by a convenient pathway from the reaction of diphenylphosphine oxide（DPPO） and vinyl-terminated siloxanes under the catalysis of triethylborane. The chemical structures of the target compounds were confirmed by nuclear magnetic resonance(¹H NMR,¹³C NMR,²⁹Si NMR and ³¹P NMR),matrix-assisted laser desorption/ionization time-of-flight mass spectrometry（MALDI-TOF-MS） and Fourier transform infrared（FT IR） measurements.Thermogravimetric analysis（TGA） results indicated that the new flame retardants possessed good thermal stability both in nitrogen and in air.FR-3 containing polyhedral oligosilsesquioxanes（POSS） moiety exhibited the best thermal properties with a 10%weight loss temperature>400℃ and a residual weight ratio>39%at 700℃ .     

Synthesis and performance of cyclic phosphorus-containing flame retardants

A series of organo-cyclic phosphorus compounds were synthesized in an attempt to find an efficient flame retardant (FR) for acrylonitrile-butadiene-styrene (ABS). The success of synthesis was confirmed by ¹H and ³¹P NMR. Thermogravimetric analysis (TGA) results reveal that cyclic phosphorus compounds synthesized in this study show almost one step degradation between 250 and 400 °C and are believed to work in the vapour phase rather than in the condensed phase. From UL-94 test, V-0 rating was achieved at 15-35 wt% loading of cyclic or cyclic alkyl phosphonate FR and no rating at 35 wt% loading of cyclic phosphate for ABS. On the other hand, a much lower loading (7.5%) was needed to obtain V-0 rating for polycarbonate when 3,9-diphenyl-3,9-dioxa-2,4,8,10-tetraoxa-3,9-diphosphaspiro-5,5-undecane (PBPP) was added as FR. All the results show that the flame retarding effect is strongly dependent on the P content of the FR incorporated. The flame retardant mechanism of cyclic phosphorus compounds is also discussed.     

Solubilities,thermostabilities and flame retardance behaviour of phosphorus-containing flame retardants and copolymers

Thirteen phosphorus-containing flame retardants were synthesized in this work. The solubilities of flame retardant [(6-oxide-6H-dibenz[c,e][1,2]oxaphosphorin-6-yl)-methyl]-butanedioic acid (DDP) in selected solvents are measured. TGA measurements of the 13 phosphorus-containing flame retardants were carried out and thermal stabilities of three flame-resistant PET (FRPET) resins were investigated. A FRPET incorporated by DDP with terephthalic acid and ethylene glycol reported in literature was also discussed and compared. The thermal stability of the FRPET is improved by the incorporation of phosphorus-containing flame retardants. The LOI values of all phosphorus-containing polyesters are higher than 27%. The improvement of the flame-resistant ability is due to the formation of the char that is not only caused by the existence of phosphorus elements in the resin but also by the relative large number of carbon atoms of the phenyl group in the flame retardants.     

阻燃剂苯并咪唑的微波合成研究进展

苯并咪唑类化合物广泛应用于医药、农药等领域,也在阻燃剂中具有重要应用.因此,利用微波辅助方法快速、高效地合成苯并咪唑类化合物已成为近年来的研究热点,本文对此进行了综述,并从经济与规模化制备苯并咪唑等方面进行了展望.     

The influence of KH-550 on properties of ammonium polyphosphate and polypropylene flame retardant composites

Ammonium polyphosphate (APP)/polypropylene (PP) composites were prepared by melt blending and extrusion in a twin-screw extruder. APP was first modified by a silane coupling agent KH-550 then added to polypropylene. The surface modification of APP by the coupling agent decreased its water solubility and its interface compatibility with the PP matrix. Limiting oxygen index (LOI) and thermogravimetric analysis (TGA) were used to characterize the flame retardant property and the thermal stability of the composites. The addition of APP improved the flame retardancy of PP remarkably. The crystal structures of APP/PP composites were characterized by X-ray diffraction (XRD). The results indicated that β-crystal phase PP may be formed. The structures and morphologies of APP, KH-550/APP and APP/PP composites were characterized by field-emission scanning electron microscope (FESEM). The mechanical property tests showed good mechanical properties of composite materials. Compared with unmodified one, the impact strength, tensile strength and elongation of modified APP/PP were all improved.     

A review on flame retardant technology in China. Part I: development of flame retardants

This paper provides an insight into some developments in flame retardants for different polymeric materials in China, primarily based on the publications that have appeared in the last 15 years. It focuses on the following aspects: halogen‐containing flame retardants, inorganic flame retardants (e.g. metal oxides and hydroxides, silicon‐containing materials, ammonium polyphosphate, red phosphorus, and expandable graphite), and organic flame retardants (e.g. aliphatic and aromatic phosphonates, nitrogen‐containing organics, and multi‐element organics). The inherently flame‐retardant polymer systems are also reviewed. The exploration of the novel flame retardants and flame‐retardant systems provides a powerful basis for the construction of flame‐retardant technologies and industrial applications in China. Copyright © 2009 John Wiley & Sons, Ltd.     

Applications of micro-scale combustion calorimetry to the studies of cotton and nylon fabrics treated with organophosphorus flame retardants

Effective testing methods are critical for developing new flame retardant textiles by the industry. However, the current testing methods all have limitations. In this research, we applied micro-scale combustion calorimetry (MCC) for evaluating the flammability of the cotton woven fabric treated with a traditional reactive organophosphorus flame retardant in combination with a synergistic nitrogen-containing additive and the nylon-6,6 woven fabric treated with a hydroxyl-functional organophosphorus oligomer and crosslinkers. We found that MCC is capable of differentiating small differences among the treated fabric samples with similar flammability. MCC is able to make quantitative measurement of the peak heat release rate, the most important parameter related to fire hazard of materials, of textile whereas such analysis is more difficult using cone calorimetry due to textile fabrics’ low thickness. By using the thermal combustion parameters measured by MCC, we were able to calculate the limiting oxygen index (LOI) of various treated cotton fabric samples with near-perfect agreement between the experimentally measured and the predicted LOI values of treated cotton fabrics. We also compared the capability of MCC and differential scanning calorimetry for analyzing flame retardant cotton textiles.     

Synthesis and applications of biscyclic phosphorus flame retardants

The influence of structural effects of organo-phosphorus flame retardants (FRs) on their flame retardant action was investigated. A series of spirobisphosphorus compounds including 3,9-dibutyl-3,9-dioxo-2,4,8,10-tetraoxa-3,9-diphosphaspiro-5,5-undecane were prepared using various synthetic methods such as the Arbuzov reaction. The chemical structure of the product was confirmed by ¹H and ³¹P NMR. Thermogravimetric analysis (TGA) results reveal that these cyclic phosphorus compounds show a single step degradation in the range of 250-400 °C and act in the gas phase rather than in the condensed phase. The obtained products were blended with an acrylonitrile-butadiene-styrene copolymer (ABS) or polycarbonate (PC) and their flame retardant behavior was evaluated using a UL-94 vertical test. V-0 ratings are achieved at 15-35 wt% loading of FR for ABS and at a much lesser amount of loading for PC. In both cases, it is apparent that the flame retardancy is strongly dependent on the P content of the flame retardant.