Theoretical and experimental analysis of the effects of the series resistance on luminous efficacy in GaN-based light emitting diodes

In this paper, a new equivalent circuit model of GaN-based light emitting diodes(LEDs) is established. The impact of the series resistance to luminous efficacy is simulated using the MATLAB software. GaN-based LEDs with different ncontact electrode materials(LEDs with Ni/Au and LEDs with Cr/Au) are fabricated. By comparing and analyzing the results of performances, we concluded that both the series resistance and the carrier loss could affect the luminous efficacy severely.LEDs with lower series resistance have higher luminous efficacy and its efficiency droop is alleviated simultaneously. To improve luminous efficacy, the fabrication process should be optimized for lower series resistance.     

Degradation behaviors of high power GaN-based blue light emitting diodes

The degradation mechanism of high power InGaN/GaN blue light emitting diodes(LEDs)is investigated in this paper.The LED samples were stressed at room temperature under 350-mA injection current for about 400 h.The light output power of the LEDs decreased by 35%during the first 100 h and then remained almost unchanged,and the reverse current at 5 V increased from 10 9A to 10 7A during the aging process.The power law,whose meaning was re-illustrated by the improved rate equation,was used to analyze the light output power-injection current(L–I)curves.The analysis results indicate that nonradiative recombination,Auger recombination,and the third-order term of carriers overflow increase during the aging process,all of which may be important reasons for the degradation of LEDs.Besides,simulating L–I curves with the improved rate equation reveal that higher-than-third-order terms of carriers overflow may not be the main degradation mechanism,because they change slightly when the LED is stressed.     

GaN基高压直流发光二极管制备及其性能分析

GaN基高压直流发光二极管工艺制备, 采用蓝宝石图形衬底(PSS) 外延片制备正梯形芯粒结构的GaN基高压直流LED.相对其他结构器件, 该结构器件发光效率最高, 封装白光后, 在色温4500 K, 驱动电流20 mA时, 光效116.06 lm/W, 对应电压50 V. 测试其I-V曲线表明, 开启电压为36 V, 对应驱动电流为1.5 mA; 在电流15 mA至50 mA时, 光功率随驱动电流增加近似于线性增加, 在此区域光效随电流增加而降低的幅度比较缓慢, 表明GaN基高压直流LED适宜于采用大电流密度驱动, 而不会出现驱动电流密度增加导致量子效率明显下降(efficiency droop), 为从芯片层面研究解决量子效率下降难题提供了一种新思路.     

Effects of electrical stress on the characteristics and defect behaviors in GaN-based near-ultraviolet light emitting diodes

The degradation mechanism of GaN-based near-ultraviolet (NUV, 320-400 nm) light emitting diodes (LEDs) with low-indium content under electrical stress is studied from the aspect of defects. A decrease in the optical power and an increase in the leakage current are observed after electrical stress. The defect behaviors are characterized using deep level transient spectroscopy (DLTS) measurement under different filling pulse widths. After stress, the concentration of defects with the energy level of 0.47-0.56 eV increases, accompanied by decrease in the concentration of 0.72-0.84 eV defects. Combing the defect energy level with the increased yellow luminescence in photoluminescence spectra, the device degradation can be attributed to the activation of the gallium vacancy and oxygen related complex defect along dislocation, which was previously passivated with hydrogen. This study reveals the evolution process of defects under electrical stress and their spatial location, laying a foundation for manufacture of GaN-based NUV LEDs with high reliability.     

High-efficiency silicon light emitting diodes

Silicon has been regarded as a notoriously poor emitter of light fundamentally due to its indirect bandgap. However, as an elemental rather than a compound semiconductor, it has the advantage of fewer background defects as well as well-developed approaches to interface passivation. By minimising parasitic optical absorption and non-radiative bulk and surface recombination, and by enhancing the effective optical photon generation volume, respectable silicon light emission efficiencies are demonstrated. These are within the range of direct gap III–V semiconductors and higher than any at low powered densities. Possible applications are also discussed.     

修饰阴极界面提高聚合物白光二极管发光效率

利用聚合物的不同溶解性,研究用旋涂方法制备双层高分子白光二极管(WPLED),采用器件结构为：ITO/PEDOT(50nm)/PVK:PFO-BT: PFO-DBT(40nm)/PFO(40nm)/Ba(4nm) /Al(120nm),当相对比例为PVK: PFO-BT:PFO-DBT=1∶4%：3%时,得到标准白光,最大电流效率为2.4 cd/A,最大亮度为3215 cd/m²,色坐标为(0.33,0.34).用水溶性的聚电介质层修饰阴极界面,器件效率可以进一步提高到5.28 cd 关键词： 聚合物发光二极管 白光 双发光层结构     

3,4,9,10-Perylenetetracarboxylicdiimide as an interlayer for ultraviolet organic light emitting diodes

Ultraviolet organic light emitting diodes with 3,4,9,10-perylenetetracarboxylicdiimide (PTCDI) interlayer have been achieved. The emission spectrum and intensity were strongly dependent on the thickness of PTCDI interlayer, in spite of the fact that PTCDI has neither much lower HOMO nor much higher LUMO level, which is considered necessary for efficient charge blocking layers. The influence of PTCDI layer was investigated in three different device configurations and obtained results are discussed. For optimal device configuration, OLED with emission centered at 370 nm and turn-on voltage of 4.5 V is obtained.     

ITO‐free top emitting organic light emitting diodes with enhanced light out‐coupling

Bottom emitting organic light emitting diodes (OLEDs) can suffer from lower external quantum efficiencies (EQE) due to inefficient out‐coupling of the generated light. Herein, it is demonstrated that the current efficiency and EQE of red, yellow, and blue fluorescent single layer polymer OLEDs is significantly enhanced when a MoO_x(5 nm)/Ag(10 nm)/MoO_x(40 nm) stack is used as the transparent anode in a top emitting OLED structure. A maximum current efficiency and EQE of 21.2 cd/A and 6.7%, respectively, was achieved for a yellow OLED, while a blue OLED achieved a maximum of 16.5 cd/A and 10.1%, respectively. The increase in light out‐coupling from the top‐emitting OLEDs led to increase in efficiency by a factor of up to 2.2 relative to the optimised bottom emitting devices, which is the best out‐coupling reported using solution processed polymers in a simple architecture and a significant step forward for their use in large area lighting and displays.     

基于发光二极管和导光板的彩色光源色度的测量

介绍一种由三色发光二极管和导光板组成的适合物理实验色度测量教学的彩色面光源,并给出了测量该光源色度的实验方法．     

Light outcoupling efficiency enhancement in organic light emitting diodes using an organic scattering layer

Crystallized 4,7‐diphyenyl‐1,10‐phenanthroline (BPhen) films deposited by convenient vacuum thermal evaporation technique have been found to be an efficient means to extract the substrate wave guided light in organic light emitting diodes (OLEDs). The optimized BPhen film working as organic scattering layer was successfully used with OLEDs for light outcoupling efficiency improvement. Enhancement of 26%, 15% and 6% in efficiency of the blue, green and red OLEDs were obtained, respectively. The achievement was found to be advantageous in terms of simplicity of fabrication method and feasibility for large area OLED applications. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effects of Mg doping in the quantum barriers on the efficiency droop of GaN based light emitting diodes

The effects of Mg doping in the quantum barriers(QBs) on the efficiency droop of GaN based light emitting diodes(LEDs) were investigated through a duel wavelength method. Barrier Mg doping would lead to the enhanced hole transportation and reduced polarization field in the quantum wells(QWs), both may reduce the efficiency droop. However,heavy Mg doping in the QBs would strongly deteriorate the crystal quality of the QWs grown after the doped QB. When increasing the injection current, the carriers would escape from the QWs between n-GaN and the doped QB and recombine non-radiatively in the QWs grown after the doped QB, leading to a serious efficiency droop.     

Saturation behavior of extrinsic photoconductivity in GaP light emitting diodes at high infrared intensities

Saturation of extrinsic photoconductivity in GaP:N(Zn, Te) diodes could be achieved by excitation with a TEA-CO₂-laser. At wavelengths in the 10 m range intensities of several 100 kW/cm² being near the damage threshold were applied. Carrier lifetimes of 60 ps at 4.2 K and 200 ps at 77 K could be estimated. The only conceivable mechanism explaining these short time constants is the capture of infrared excited holes by ionized shallow acceptors in the highly compensated p-side of the diode.     

载流子分布对GaN基LED频率特性的影响

分别在直流偏置和交流偏置下,对大功率GaN基LED的电学和光学特性进行了研究。结果显示,通过改变靠近p型层的量子垒（也就是最后一个量子垒）中的In组分可以调控有源区中的载流子分布。有源区内积累的电子会引起负电容效应。而通过降低有源区量子垒的势垒高度,可以改善LED中载流子传输特性,并实现载流子复合速率及通信调制带宽20%的提高。这个工作将有助于理解GaN基LED中载流子分布对频率特性的影响,并为设计适用于可见光通信的大功率高速LED奠定基础。     

Thin film hexagonal gold grids as transparent conducting electrodes in organic light emitting diodes

Indium Tin Oxide (ITO) coated glass is currently the preferred transparent conducting electrode (TCE) for organic light emitting diodes (OLEDs). However, ITO has its drawbacks, not least the scarcity of Indium, high processing temperatures, and inflexibility. A number of technologies have been put forward as replacements for ITO. In this paper, an OLED based on a gold grid TCE is demonstrated, the light emission through the grid is examined, and luminance and current measurements are reported. The gold grid has a sheet resistance of 15 Ω□⁻¹ and a light transmission of 63% at 550 nm, comparable to ITO, but with advantages in terms of processing conditions and cost. The gold grid OLED has a lower turn‐on voltage (7.7 V versus 9.8 V) and achieves a luminance of 100 cdm⁻² at a lower voltage (10.9 V versus 12.4 V) than the reference ITO OLED. We discuss the lower turn‐on voltage and the uniformity of the light output through the gold grid TCE and examine the conduction mechanisms in the ITO and gold grid TCE OLEDs.     

Auger carrier leakage in III‐nitride quantum‐well light emitting diodes

Auger induced leakage is shown to be a contributing factor for the internal quantum efficiency (IQE) droop in III‐nitride quantum‐well light emitting diodes (LEDs). The mechanism is based on leakage current from carrier spill‐out of the well originating from energy transfer during Auger recombination. Adding this leakage reduces the Auger coefficient by 50% when compared to a standard Auger model with cubic density dependence. As reference, experimental data of a green quantum‐well LED are taken. Direct leakage due to non‐ideal carrier capture and re‐emission out of the well affects the IQE at current densities much larger than the maximum IQE point. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Internal quantum efficiency drop induced by the heat generation inside of light emitting diodes （LEDs）

The reasons for low output power of AlGaInP Light Emitting Diodes (LEDs) have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especially at a large injected current which would reduce both the internal and external quantum efficiencies. Two kinds of LEDs with the same active region but different window layers have been fabricated. The new window layer composed of textured 0.5 μm GaP and thin Indium-Tin-Oxide film has shown that low external quantum efficiency (EQE) has serious impaction on the internal quantum efficiency (IQE), because the carrier distribution will change with the body temperature increasing due to the heat inside, and the test results have shown the evidence of LEDs with lower output power and bigger wavelength red shift.     

C-V法研究温度对GaN基蓝光二极管pn结的影响

采用C-V法,根据C^-2-V曲线和C^-3-V曲线,并结合C-V幂律指数k,分析了T=25~-195℃温度范围内,温度变化对GaN基蓝光发光二极管pn结类型的影响。实验结果表明:当T为25℃和-50℃时,C^-2-V呈明显的线性关系,同时幂律指数k为0.5,说明该温度范围内的pn结类型为严格的突变结;而温度降低至-100℃时,k值变为0.45,说明pn结类型开始发生变化;当温度继续降低至-150℃和-195℃时,幂律指数k分别为0.30和0.28,说明pn结类型已经发生了变化,变为非突变非缓变结。造成这一现象的原因是低温导致的载流子冻析效应,以及晶体的缺陷和界面态形成的局域空间电荷区在低温环境下,影响了pn结原来的空间电荷分布,并改变了pn结类型。     

Direct observation of the potential distribution within organic light emitting diodes under operation

We show the first direct measurement of the potential distribution within organic light emitting diodes (OLEDs) under operation and hereby confirm existing hypotheses about charge transport and accumulation in the layer stack. Using a focused ion beam to mill holes in the diodes we gain access to the cross section of the devices and explore the spatially resolved potential distribution in situ by scanning Kelvin probe microscopy under different bias conditions. In bilayer OLEDs consisting of tris(hydroxyquinolinato) aluminum (Alq₃)/N, N ′‐bis(naphthalene‐1‐yl)‐N,N ′‐bis(phenyl) benzidine (NPB) the potential exclusively drops across the Alq₃ layer for applied bias between onset voltage and a given transition voltage. These findings are consistent with previously performed capacitance–voltage measurements. The behavior can be attributed to charge accumulation at the interface between the different organic materials. Furthermore, we show the potential distribution of devices with different cathode structures and degraded devices to identify the cathode interface as main culprit for decreased performance. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Enhancement of the light extraction of GaN-based green light emitting diodes via nanohybrid structures

Improvement in the light extraction efficiency (LEE) of GaN-based green light emitting diodes (LEDs) with ZnO nanostructures synthesized by a hydrothermal method is reported. Formation of ZnO nanorods, hemispheres, and cones was controlled by varying the pH of the aqueous synthesis solution. The shape of the ZnO nanostructures integrated onto the LEDs shows a strong relationship with the LEE characteristics of GaN-based green LEDs. The electroluminescence (EL) intensity of LEDs covered by ZnO nanostructures increased compared to conventional LEDs. In terms of LEE, LEDs with surface-textured ZnO hemispheres showed the highest EL intensity, which can be attributed to an increase in the effective critical angle, the escape cone, and multiple scattering. Finite difference time domain (FDTD) simulation was conducted to theoretically confirm the experimental results.     

Organic light emitting diodes using magnesium doped organic acceptor as electron injection layer and silver as cathode

Organic light emitting diodes employing magnesium doped electron acceptor 3, 4, 9, 10 perylenetetracarboxylic dianhydride (Mg:PTCDA) as electron injection layer and silver as cathode were demonstrated. As compared to Mg:Ag cathode, the combination of the Mg:PTCDA layer and silver provided enhanced electron injection into tris (8-quinolinolato) aluminium. The device with 1:2 Mg:PTCDA and Ag showed an increase of about 12% in the maximum current efficiency, mainly due to the improved hole-electron balance, and an increase of about 28% in the maximum power efficiency, as compared to the control device using Mg:Ag cathode. The properties of Mg:PTCDA composites were studied as well.