SrAl_2B_2O_7:Dy~(3+)材料的制备及其发光性能

采用高温固相法制备了SrAl2B2O7:Dy3+发光材料.在350nm紫外光激发下,测得SrAl2B2O7:Dy3+材料的发射光谱为一个多峰宽谱,主峰分别为480,573和678nm;分别和Dy3+的4F9/2→6H15/2,4F9/2→6H13/2,4F9/2→6H11/2的跃迁发射相对应;监测573nm的发射峰,得到材料的激发光谱为一个多峰宽谱,主峰分别为295,325,350,365,400nm.研究了Dy3+掺杂浓度对SrAl2B2O7:Dy3+材料发射光谱的影响,随着Dy3+掺杂浓度的增大,SrAl2B2O7:Dy3+材料的Iy/Ib逐渐增大,根据Judd-Ofelt理论解释了其原因.随着Dy3+掺杂浓度的增大,Dy3+的4F9/2→6H13/2跃迁产生的573nm发射峰强度先增大,在4%时达到最大值,之后减小,其自身的浓度猝灭机理为电偶极-电偶极相互作用.不同的电荷补偿剂Li+,Na+,K+的引入均使发光强度得到提高,尤其以Li+最佳,发光强度提高了大约33%.     

980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er³⁺/Yb³⁺共掺杂ZrO₂-Al₂O₃粉末的样品，并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现，在可见光范围内有3个强的发光带，一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带，分别对应于Er³⁺离子的以下辐射跃迁：⁴F_9/2→⁴I_15/2、⁴S_3/2→⁴I_15/2、 ²H_11/2→⁴I_15/2.其中又以Er³⁺离子的⁴F_9/2→⁴I_15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析，发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测，发现ZrO₂主要以立方相为主，并且计算得到了这种立方结构的晶格常数.Al₂O₃固溶于ZrO₂中，Al³⁺嵌入ZrO₂后产生氧空位，导致ZrO₂晶体的对称性降低，这种结构变化更有利于提高上转换效率，即上转换发光强度增强. 关键词： 3+/Yb³⁺')" href="#">Er³⁺/Yb³⁺ 上转换 2-Al₂O₃')" href="#">ZrO₂-Al₂O₃ 荧光 稀土     

Up-conversion emissions of Er<Superscript>3+</Superscript>-Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by the arc discharge synthesis method

The Er³⁺-Yb³⁺ codoped Al₂O₃ nanoparticles with an average particle size of about 50 nm have been synthesized by an arc discharge synthesis method. The green and red up-conversion emissions centered at about 526, 547 and 677 nm, corresponding respectively to the ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978-nm semiconductor laser diode excitation. The Annealing has evident effect on the up-conversion emissions of the samples: The red up-conversion emission is noticeable before annealing; however, the green up-conversion emission becomes predominant after annealing. The mixture of (Er,Yb)₃Al₅O₁₂ and α-(Al,Er,Yb)₂O₃ phases is more favorable for green up-conversion emissions due to an enhancement of the ESA (I) of ⁴I_11/2+a photon→⁴F_7/2 and ET (III) of ²F_5/2(Yb³⁺)+⁴I_11/2(Er³⁺)→²F_7/2(Yb³⁺)+⁴F_7/2(Er³⁺) processes. The two-photon absorption up-conversion process is involved in the green and red up-conversion emissions. The results have proved that arc discharge synthesis is a new promising preparation technology for optical materials. Supported by National Natural Science Foundation of China (Grant No. 10804015), the Scientific Research Foundation for Doctor of Liaoning Province (Grant No. 20071095), and the Educational Committee Foundation of Liaoning Province (Grant No. 2008123)     

NaREO2 (RE= Lu，Y) 的制备及其结构的研究

用高温固相法制备了NaLuO2和NaYO2晶体粉体.制备纯相的NaLuO2粉体晶体困难,而制备纯相NaYO2粉体晶体相对容易.为了测定NaLuO2产物中含少量Lu2O3不纯相的量,用X射线衍射绝标法确定了样品中这两者的重量比和谱峰比的关系,得到了绝标法常数kLu2O3关键词： 2')" href="#">NaLuO2 2')" href="#">NaYO2 2O3')" href="#">Lu2O3 XRD定量分析 稀土发光     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

Y2O3:Yb3+,Tm3+纳米材料的可见及紫外上转换发光

通过燃烧法制备了Yb³⁺-Tm³⁺共掺的Y₂O₃纳米粉体,并对样品在980 nm激光照射下的上转换发光特性进行了研究.实验发现,样品在可见光区域能够产生强烈的蓝色发光(476 nm和487 nm)和较弱的红色发光(约650 nm),而且同时观察到了两个紫外发光峰¹I₆→³H₆ (~297 nm)和^{1关键词： 2O₃:Yb3+')" href="#">Y₂O₃:Yb3+ 3+}')" href="#">Tm³⁺ 上转换光谱 敏化 紫外发光     

Synthesis of Y2Si2O7:Eu nanocrystal and its optical properties

Nanocrystalline Y₂Si₂O₇:Eu phosphor with an average size about 60 nm is easily prepared using silica aerogel as raw material under ultrasonic irradiation and annealing temperature at 300-600 °C and this nanocrystalline decomposes into Y₂O₃:Eu and silica by heat treatment at 700-900 °C. The excitation broad band centered at 283 and 254 nm results from Eu³⁺ substituting for Y³⁺ in Y₂Si₂O₇ and Y₂O₃/SiO₂, respectively. Compared with Y₂O₃:Eu/SiO₂ crystalline, the PL excitation and emission peaks of Y₂Si₂O₇:Eu nanocrystalline red-shift and lead to the enhance of its luminescence intensity due to the different chemical surroundings of Eu³⁺ in above nanocrystallines. The decrease of PL intensity may be ascribed to quenching effect resulting from more defects in Y₂O₃:Eu/SiO₂ crystalline.     

Thermal reactions of 2-iodoethanol on Cu(1 0 0)

Temperature-programmed reaction/desorption, X-ray photoelectron spectroscopy, and reflection-absorption infrared spectroscopy have been employed to investigate the reactions of ICH₂CH₂OH on Cu(1 0 0) under ultrahigh-vacuum conditions. ICH₂CH₂OH can dissociate on Cu(1 0 0) at 100 K, forming a -CH₂CH₂OH surface intermediate. Density functional theory calculations predict that the -CH₂CH₂OH is most probably adsorbed on atop site. -CH₂CH₂OH on Cu(1 0 0) further decomposes to yield C₂H₄ below 270 K. No evidence shows the formation of -CH₂CH₂O- intermediate in the reactions of ICH₂CH₂OH on Cu(1 0 0) in contrast to the decomposition of BrCH₂CH₂OH on Cu(1 0 0) and ICH₂CH₂OH on Ag(1 1 1) and Ag(1 1 0), exhibiting the effects of carbon-halogen bonds and metal surfaces.     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

硼酸对亚微米级Ca3Sc2Si3O12:Ce绿色荧光粉的制备及发光性能的影响

采用凝胶-燃烧法合成了Ca₃Sc₂Si₃O₁₂ ∶Ce绿色LED用荧光粉,用X射线粉末衍射(XRD)、扫描电镜(SEM)、荧光光谱仪等对合成产物进行了分析和表征.结果表明:通过添加H₃BO₃做助熔剂,制得的荧光粉晶相纯正,颗粒形貌均呈现为较规则的类球形,而且所得荧光粉的粒径均小于1 μm.发射光谱呈现为一宽带,发射主峰位于505 nm,该宽峰对应于Ce³⁺关键词： 白光LED 荧光粉 3Sc₂Si₃O₁₂ ∶Ce')" href="#">Ca₃Sc₂Si₃O₁₂ ∶Ce 发光     

Photoluminescence properties and effects of dopant concentration in Bi2ZnB2O7:Tb phosphor

A novel green phosphor, Tb³⁺ doped Bi₂ZnB₂O₇ was synthesized by conventional solid state reaction method. The phase of synthesized materials was determined using the XRD, DTA/TG and FTIR. The photoluminescence characteristics were investigated using spectrofluorometer at room temperature. Bi₂ZnB₂O₇:Tb³⁺ phosphors excited by 270 nm and 485 nm wavelengths. The emission spectra were composed of three bands, in which the dominated emission of green luminescence Bi₂ZnB₂O₇:Tb³⁺ attributed to the transition ⁵D₄ → ⁷F₅ is centered at 546 nm. The dependence of the emission intensity on the Tb³⁺ concentration for the Bi_2−xTb_xZnB₂O₇ (0.01 ≤ x ≤ 0.15) was studied and observed that the optimum concentration of Tb³⁺ in phosphor was 13 mol% for the highest emission intensity at 546 nm.     

Er3+及Er3+/Yb3+掺杂ZrO2-Al2O3的制备及发光性质

采用共沉淀法制备了纳米晶ZrO₂-Al₂O₃∶Er³⁺发光粉体.所制备的粉体室温下具有Er3+离子特征荧光发射,主发射在绿光,其中位于547 nm、560 nm的绿光最强,并得出稀土离子与基质之间有能量传递.对不同煅烧温度下的样品研究表明:因不同温度下所制得的样品晶相不同.研究了纳米晶ZrO2-Al2O3∶Er3+及ZrO₂-Al₂O₃∶Er³⁺/Yb³⁺的上转换发光,并分析了上转换的跃迁机制.发现ZrO₂-Al₂O₃∶Er³⁺的绿光为双光子过程,而ZrO₂-Al₂O₃∶Er³⁺、Yb³⁺的上转换光谱中,红光和绿光也为双光子过程,而极弱的蓝光为三光子过程.讨论了Er³⁺的浓度猝灭现象.最适宜掺杂浓度的原子分数为2%（Er³⁺/Zr⁴⁺）.     

CH3I分子的光解离的自旋-轨道从头计算

采用从头计算二阶自旋-轨道多组态准简并微扰理论计算了碘代甲烷CH₃I分子与基态²I⁰_3/2和激发态²I^0*_1/2原子解离极限相关联的势能曲线. 计算了CH₃I分子的吸收谱,分析了CH₃I分子的光解离过程,并估计了激发态碘原子²I^0*_3/2的量子产额. 计算结果表明,该方法可用以解释光解离实验结果. 关键词： 3I分子')" href="#">CH₃I分子 自旋-轨道耦合 量子产额 光解离     

Influence of carbon templates and Yb concentration on red and green luminescence of uniform Y2O3:Yb/Er hollow microspheres

Uniform Yb³⁺ and Er³⁺-codoped Y₂O₃ hollow microspheres were synthesized via urea co-precipitation using carbon spheres as templates. Intense red emission (⁴F_9/2→⁴I_15/2) and weak green emission (²H_11/2, ⁴S_3/2→⁴I_15/2) of Er³⁺ were observed for the Yb³⁺ and Er³⁺-codoped Y₂O₃ hollow microspheres under 980 nm infrared excitation. The integrated intensity of visible emission and the ratio of red to green were found to be strongly dependent on the amount of carbon sphere templates and the concentration of Yb³⁺ ions. The amount of carbon sphere templates also plays an important role in adjusting the size of crystallite. Multi-phonon relaxation resulted from the absorbents (OH⁻ and CO₃²⁻) on the surface of the crystallite, and efficient occur of energy transfer processes and cross-relaxation between Er³⁺ and Yb³⁺ are responsible for the enhancement of intensity ratio of red to green emission. Interestingly, for higher concentration of Yb³⁺ ions, the green emission is assigned to a three-phonon process in Y₂O₃:Yb/Er hollow microspheres, which also could result in the increase of the red to green emission ratio. An explanation to account for these behaviors was presented.     

NMR Study on Coexistence of Magnetic Order and Superconductivity in RuSr2GdCu2O8

Electronic and magnetic properties of RuSr₂GdCu₂O₈ have been investigated by resistivity, magnetization and NMR measurements. Magnetic order (T _C=133 K) and superconducting transition (T _S(onset) 52 K) have been confirmed in RuSr₂GdCu₂O₈. We observed two kinds of Ru-NMR signals (the hyperfine fields of ¹⁰¹Ru are 590 kOe and 290 kOe), suggesting a possible charge segregation of Ru⁴⁺(S=1) and Ru⁵⁺(S=3/2) in the RuO₂ layers. Holes can be inherently doped in the CuO₂ layers from the (Ru⁴⁺, Ru⁵⁺)O₂ layers, and the superconductivity can occur under weak magnetic interactions between Ru and Cu spins in RuSr₂GdCu₂O₈.     

Color improvement of white-light through Mn-enhancing yellow-green emission of SrSi2O2N2:Eu phosphor for white light emitting diodes

Photoluminescence (PL) enhancement of SrSi₂O₂N₂:Eu and the resultant color improvement of white-light were investigated via co-doping Mn with Eu. We observed that a unique absorption of host lattice of SrSi₂O₂N₂ and its visible band emission peaked at around ∼550 nm for SrSi₂O₂N₂:Mn²⁺ in the wavelength range of 450-600 nm. This highly eye-sensitive ∼550 nm-peaked band emission of SrSi₂O₂N₂ doped with Mn²⁺ happens to overlap the 535 nm-peaked band emission of SrSi₂O₂N₂ doped with Eu²⁺, resulting in an intensified photoluminescence in a maximum by 355%. By combining this as-prepared Mn intensified SrSi₂O₂N₂:Eu phosphor with blue InGaN chip, the quality of white-light was improved to 93.3% for color rendering index and 3584 K for correlated color temperature.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.