甲醇重整反应中Pt/γ-Al2O3催化剂纳米Pt粒径与催化性能关系研究

利用硝基甲烷还原法在室温条件下得到了纳米Pt粒径可控的担载Pt/γ-Al₂O₃催化剂, 并利用甲醇重整反应为反应探针考察了Pt粒径与催化反应性能之间的关系, 发现催化反应的性能与担载贵金属颗粒粒径之间存在明显的相关性. 通过透射电镜(TEM)、X射线衍射(XRD)、程序升温还原(TPR)等测试手段对催化剂进行表征, 发现钠米Pt的粒径大小不但影响甲醇重整反应的活性, 同时也影响反应的选择性, 即催化剂的催化性能与担载贵金属粒径之间存在明显的尺度效应.     

Pt/K2La2Ti3O10催化剂的合成及其光催化分解甲醇水溶液制氢

用高温固相法合成了具有类钙钛矿型结构的层状化合物K₂La₂Ti₃O₁₀, 用XRD, UV-DRS对其进行表征. 利用不同还原方法制备了Pt/K₂La₂Ti₃O₁₀光催化剂, 并且用脉冲氢氧滴定法(HOT)测定了K₂La₂Ti₃O₁₀表面Pt的分散度. 考察了Pt/K₂La₂Ti₃O₁₀光催化分解甲醇水溶液制氢的活性. 比较了负载Pt与负载Ni和纯的K₂La₂Ti₃O₁₀的光催化活性. 研究了Pt负载量、不同还原方法对光催化分解水制氢反应活性的影响. 在最佳的Pt负载量2%(质量百分比)下, 产氢速率达到233.88 mmol·h^&;#8722;1. 讨论了该催化剂的能带结构及反应机理.     

Ce掺杂K2La2Ti3O10催化剂的可见光高效催化制氢的研究

采用高温固相法合成了铈掺杂的K₂La₂Ti₃O₁₀催化剂, 利用X射线衍射(XRD)、紫外-可见漫反射(UV-vis DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征. 考察了催化剂的可见光催化分解甲醇水溶液制氢的活性, 并对可见光催化机理进行了分析. 研究表明, 铈的掺杂没有改变K₂La₂Ti₃O₁₀的微晶结构, 并使催化剂粒径有所减小. 紫外可见漫反射分析表明禁带宽度为2.3 eV左右, 对可见光具有较高吸收. XPS表明La和Ti为＋3和＋4价, 而Ce则是＋3和＋4的混合价态. 担载2 wt% Pt后, 在可见光下光催化活性大大提高, 当铈的掺杂量为0.5 mol%(即Ce取代La的摩尔百分量)时, 光催化活性达到最大, 产氢速率为0.05 mmol/h; 光照5 h后产氢量为0.22 mmol, 而纯K₂La₂Ti₃O₁₀的产氢量只有0.037 mmol.     

Pt / InVO4 / TiO2可见光催化剂的制备及性能研究

采用溶胶-凝胶法制备了Pt / InVO₄ / TiO₂三元体系可见光催化剂。以乙烯为模拟目标分子，评价其光催化活性并与二元体系催化剂Pt / TiO₂ 和InVO₄ / TiO₂进行比较。用DRS，XRD对催化剂的吸收带边和晶型进行了表征。结果表明：Pt / InVO₄ / TiO₂在可见光区（λ>450 nm）的光催化比活性比Pt / TiO相似文献   

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H₂-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al₂O₃催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H2-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

Pt/MOx(M=Ni,Fe,Co,Ce)催化剂上CO氧化反应中抗H2O与CO2的性能研究

我们研究了4种负载型Pt催化剂（1Pt/NiO、1Pt/FeO_x、1Pt/Co₃O₄和Pt/CeO₂）上不同反应条件下CO氧化活性及抗H₂O和CO₂性能.发现反应气氛中CO₂的加入与CO形成了竞争吸附,并在催化剂表面形成了碳酸盐物种堵塞了活性位,从而导致催化剂失活.反应气氛中H₂O的加入对1Pt/CeO₂催化剂的活性有所抑制,但对1Pt/FeO_x、1Pt/NiO和1Pt/Co₃O₄催化剂的活性却有促进作用.在1Pt/FeO_x和1Pt/CeO₂催化剂上的分步反应实验和动力学研究表明,尽管H₂O的加入在两种催化剂上均与CO形成了竞争吸附,但在1Pt/FeO_x催化剂上H₂O在载体表面解离形成的羟基更易与CO反应,开辟了新的反应途径,从而提高了反应性能.此外,H₂O的加入能有效分解该催化剂上的碳酸盐物种,从而保持了其稳定性.     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

高活性耐硫MoO3改性NiO-Al2O3催化剂用于焦炉煤气甲烷化

采用双水解共沉淀法结合浸渍法合成了系列的MoO₃改性的xMoO₃/NiO-Al₂O₃催化剂(x%为MoO₃的质量分数),利用固定床装置对催化剂的甲烷化反应活性和耐硫性能进行评价,并对失活前后催化剂进行详细表征。结果表明,随着MoO₃含量的升高MoO₃改性后的催化剂甲烷化活性有所下降,但MoO₃的掺杂显著提升了催化剂的耐硫性能。催化剂低温甲烷化活性降低的原因在于MoO₃负载量的增加降低了催化剂的活性比表面积,但MoO₃的引入也为硫化物提供了一个竞争吸附位点,进而延缓了活性位点的硫中毒过程。当 MoO₃负载量(质量分数)为 12.5% 时,12.5MoO₃/NiO-Al₂O₃催化剂在 143 mg·m^-3 H₂S/H₂气氛下运行时间长达7 h,远高于其他催化剂。12.5MoO₃/NiO-Al₂O₃催化剂吸收硫的量(质量分数)达到0.71%,是NiO-Al₂O₃催化剂硫吸附量的1.48倍。XPS表征进一步发现12.5MoO₃/NiO-Al₂O₃催化剂表面生成的MoS₂最多,这说明在此负载量下Mo优先吸附了更多的硫而保护了活性位点。此外,MoO₃负载量为12.5%时,MoO₃在催化剂表面接近单层分散阀值,当竞争吸附发生时,为硫化物提供更多的吸附位点。     

高活性耐硫MoO3改性NiO-Al2O3催化剂用于焦炉煤气甲烷化

采用双水解共沉淀法结合浸渍法合成了系列的MoO₃改性的xMoO₃/NiO-Al₂O₃催化剂(x%为MoO₃的质量分数),利用固定床装置对催化剂的甲烷化反应活性和耐硫性能进行评价,并对失活前后催化剂进行详细表征。结果表明,随着MoO₃含量的升高MoO₃改性后的催化剂甲烷化活性有所下降,但MoO₃的掺杂显著提升了催化剂的耐硫性能。催化剂低温甲烷化活性降低的原因在于MoO₃负载量的增加降低了催化剂的活性比表面积,但MoO₃的引入也为硫化物提供了一个竞争吸附位点,进而延缓了活性位点的硫中毒过程。当MoO₃负载量(质量分数)为12.5%时,12.5MoO₃/NiO-Al₂O₃催化剂在143 mg·m^-3 H₂S/H₂气氛下运行时间长达7 h,远高于其他催化剂。12.5MoO₃/NiO-Al₂O₃催化剂吸收硫的量(质量分数)达到0.71%,是NiO-Al₂O₃催化剂硫吸附量的1.48倍。XPS表征进一步发现12.5MoO₃/NiO-Al₂O₃催化剂表面生成的MoS₂最多,这说明在此负载量下Mo优先吸附了更多的硫而保护了活性位点。此外,MoO₃负载量为12.5%时,MoO₃在催化剂表面接近单层分散阀值,当竞争吸附发生时,为硫化物提供更多的吸附位点。     

Pt-SnO2 / C催化剂对乙醇和吸附态CO的电催化氧化

由于乙醇最有可能成为直接甲醇燃料电池（DMFC）的替代燃料，因此近年来。对乙醇的电化学氧化及直接乙醇燃料电池的研究已引起人们的很大兴趣。甲醇毒性较大并且易透过Nafion膜进入阴极造成阴极的混合电位而影响DMFC的阴极性能．这是制约DMFC走向实用化的主要问题之一。因此人们在致力于研究直接甲醇燃料电池的同时．也寻求其它的小分子醇作为甲醇的替代燃料。乙醇是除甲醇以外最简单的醇．它来源广泛．无毒，是可再生和环保型能源．并且也有较高的能量密度和反应活性。但是乙醇在电极上的完全氧化因涉及到C-C键的断裂要比甲醇困难．阳极反应动力学过程也比较缓慢。到目前为止铂基催化剂仍然是乙醇氧化最好的催化剂．虽然也有使用非铂催化剂研究乙醇的电氧化，但催化活性远不如铂基催化剂高。     

ZrO_2负载Pt催化巴豆醛选择性加氢

以高比表面积ZrO2为载体,采用浸渍法制备了负载型Pt催化剂,应用于常压下气相巴豆醛加氢反应,考察了Pt负载量和H2还原温度等对巴豆醛选择性加氢性能的影响.实验结果表明,Pt负载量(质量分数)为3%的3Pt/ZrO2催化剂经500℃还原后,具有较高的巴豆醛选择性加氢性能:巴豆醛转化率为27%,巴豆醇的选择性为55%.X射线粉末衍射(XRD)分析,CO化学吸附,NH3程序升温脱附(NH3-TPD)表征结果表明Pt/ZrO2催化剂上Lewis强酸中心和适宜的Pt颗粒(约为8nm)有利于巴豆醛选择性加氢生成巴豆醇.     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Effect of TiO2 Calcination Pretreatment on the Performance of Pt/TiO2 Catalyst for CO Oxidation

In order to improve the CO catalytic oxidation performance of a Pt/TiO₂ catalyst, a series of Pt/TiO₂ catalysts were prepared via an impregnation method in this study, and various characterization methods were used to explore the effect of TiO₂ calcination pretreatment on the CO catalytic oxidation performance of the catalysts. The results revealed that Pt/TiO₂ (700 °C) prepared by TiO₂ after calcination pretreatment at 700 °C exhibits a superior CO oxidation activity at low temperatures. After calcination pretreatment, the catalyst exhibited a suitable specific surface area and pore structure, which is beneficial to the diffusion of reactants and reaction products. At the same time, the proportion of adsorbed oxygen on the catalyst surface was increased, which promoted the oxidation of CO. After calcination pretreatment, the adsorption capacity of the catalyst for CO and CO₂ decreased, which was beneficial for the simultaneous inhibition of the CO self-poisoning of Pt sites. In addition, the Pt species exhibited a higher degree of dispersion and a smaller particle size, thereby increasing the CO oxidation activity of the Pt/TiO₂ (700 °C) catalyst.     

Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

Pt LIII-edge XANES and EXAFS studies on γ-Al2O3 supported Pt catalysts

Pt L_III-edge XANES and EXAFS were employed to investigate the nature of Pt/γ-Al₂O₃, Pt−Sn/γ-Al₂O₃ and Pt−Fe/γ-Al₂O₃ catalysts. The results indicated that Pt species on these catalysts were all in the oxidized states before reduction, and in the metallic states after reduction. The dispersity of the Pt species on the catalysts was very high after reduction. The electronic properties of the highly dispersed Pt species were different from that of the bulk Pt in large crystallites. An interaction between Pt and the metal-oxide modified γ-Al₂O₃ support is proposed. The interaction improved the dispersity of the Pt species on the catalysts and is thought to be the reason for the enhanced activity and selectivity for dehydrogenation reactions over these catalysts.     

国产航空煤油裂解催化剂Pt/ZrxTixAl1-2xO2的性能

采用共沉淀法制备了一系列Zr_xTi_xAl_1-2xO₂复合氧化物载体材料,考察了其作为裂解催化剂载体对航空煤油裂解反应的影响.?采用全自动吸附仪、X射线衍射、扫描电镜/能谱仪联用、NH₃-程序升温脱附等手段对催化剂进行了表征.?结果表明,当ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂具有最大的比表面积和孔容;具有最强的表面酸性和最集中的强酸中心密度,且具有良好的再生功能.?实验结果表明,载体ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂上650?℃裂解产气量较热裂解提高了2.1倍,700?℃时提高1.4倍.?另外,该系列载体材料经1000?℃焙烧5?h后,所制得的催化剂几乎失去了催化活性.     

Characterization of Au-Rh/TiO2 catalysts by CO adsorption; XPS, FTIR and TPD experiments

On X-ray photoelectron spectra of the Au-Rh/TiO₂ catalysts the position of Au4f peak was practically unaffected by the presence of rhodium, the peak position of Rh3d, however, shifted to lower binding energy with the increase of gold content of the catalysts. Rh enrichment in the outer layers of the bimetallic crystallites was experienced. The bands due to Au⁰-CO, Rh⁰-CO and (Rh⁰)₂-CO were observed on the IR spectra of bimetallic samples, no signs for Rh⁺-(CO)₂ were detected on these catalysts. The results were interpreted by electron donation from titania through gold to rhodium and by the higher particle size of bimetallic crystallites.