Synthesis and properties of fibers prepared from lactic acid–glycolic acid copolymer

A method for preparing laboratory samples of fibers from glycolide-co-D,L-lactide to produce bioresorbing suture filaments with a controlled complex of properties is developed. The morphology of fibers obtained through melt spinning is studied. The peculiarities of the mechanical properties of fibers are investigated.     

Swelling–shrinking behaviors of poly(N-isopropylacrylamide) and poly(N-n-propylacrylamide) gels prepared by chemical and radiation crosslinking methods

The swelling and shrinking kinetics of thermosensitive gels based on N-isopropylacrylamide (NiPAAm) and N-n-propylacrylamide (NnPAAm) were studied. Four gels cylindrical in shape were prepared by two different methods: γ-ray irradiation to aqueous solutions of poly(NiPAAm) (PNiPAAm) or poly(NnPAAm) (PNnPAAm) and redox polymerization of NiPAAm or NnPAAm monomer using N,N′-methylenebisacrylamide as a crosslinker. There were a few differences in the swelling kinetics among these gels. However, a marked difference was observed in the shrinking processes, the rate of which was faster in the order of radiation-crosslinked PNiPAAm gel > radiation-crosslinked PNnPAAm gel > chemically crosslinked PNnPAAm gel > chemically crosslinked PNiPAAm gel. This difference was discussed in terms of the microscopic structure of the gels, which was studied by light scattering techniques. It was found that the static inhomogeneities frozen in the chemically and radiation-crosslinked gels play a key role in their shrinking kinetics.     

Nonwoven blend composites based on poly(3-hydroxybutyrate)–chitosan ultrathin fibers prepared via electrospinning

With the use of scanning electron microscopy, differential scanning calorimetry, and electron paramagnetic resonance, the structural–dynamic analysis of ultrathin fibrous matrixes based on poly(3-hydroxybutyrate) and blend composites of this polymer with chitosan is performed. It is shown that the addition of a small amount of chitosan causes change in the morphologies of the matrixes and leads to a marked increase in their melting enthalpies. It is found that the studied fibers contain amorphous regions with various morphologies. The dynamics of the spin probe TEMPO in these regions is investigated, and its change under the influence of increased temperature, an aqueous medium, and ozone is examined. The mechanism controlling the effects of chitosan, temperature, and an oxidative aggressive medium on the structuring of fibers is advanced.     

Swelling-shrinking behavior of chemically cross-linked polypeptide gels from poly(α-L-lysine), poly(α-DL-lysine), poly(ɛ-L-lysine) and thermally prepared poly(lysine): effects of pH, temperature and additives in the solution

We synthesized the glutaraldehyde cross-linked hydrogels using four kinds of poly(lysine)s (PLs) and measured the equilibrium swelling ratio (Q) as a function of pH. Also measured was the temperature change of Q at a fixed pH (11.6) in the absence and presence of additives (LiBr, methanol and urea) that affect the secondary structure of PLs. The swelling data were examined using a force balance approach in which the repulsive and attractive interactions among the cross-linked PL chains were considered based on the conformational properties of PLs in aqueous solutions. It was found that the formation of the helical segments in the cross-linked chain has little effect in the gel collapse, but their association acts as the attractive interaction causing the gel to shrink. The formation of the beta-sheet structure within the network also acts as the attractive interaction. These attractive interactions are mainly due to the hydrogen bonding, but hydrophobic interactions between the lysine side chains should be considered. In addition, in the swelling behavior of all the PL gels the polyampholyte nature appears due to electrostatic interactions of the basic groups with the C-terminal carboxyl group.     

Effects of fabrication conditions on the structure and function of membranes formed from poly(acrylonitrile–vinylchloride)

Phase-inversion membranes formed from poly(acrylonitril–co-vinylchloride) (PAN–PVC) have been utilized for encapsulating living cells for transplantation; however, a detailed analysis of the structure and function of the integral skin layer has not been reported. PAN–PVC membranes fabricated under different precipitation conditions were analyzed using microscopic techniques and several functional tests. Structural analysis with scanning atomic force microscopy (AFM) revealed the presence of nodular elements in the skin layer which changed as a function of precipitation conditions. In addition, membrane hydraulic permeabilities, sieving coefficients, and diffusive permeabilities also varied with precipitation conditions. Furthermore, changes in the functional properties could be related to the size of the nodular elements and their accompanying interstitial space. The results provide insight into the fundamental interrelationships that exist between membrane fabrication, the fine surface morphology of the skin layer, and membrane performance.     

Solubility of naphthalene in aqueous solutions of poly(ethylene glycol)–poly(propylene glycol)–poly(ethylene glycol) triblock copolymers and (2-hydroxypropyl)cyclodextrins

The solubility of naphthalene was investigated in aqueous solutions of triblock copolymers poly(ethylene glycol)–poly(propylene glycol)–poly(ethylene glycol) (PEG–PPG–PEG) and (2-hydroxypropyl)cyclodextrins. The results with solutions of the individual solubilizers were as expected: the solubility enhancement was much higher with a micelle-forming copolymer than with the non-micellizing one and with (2-hydroxypropyl)--cyclodextrin (HPBCD) than with (2-hydroxypropyl)--cyclodextrin (HPACD). Although the formation of inclusion complexes between HPACD and PEG and between HPBCD and PPG is well established, the naphthalene solubility in mixed solutions does not significantly deviate from that predicted for a mixture of independent solubilizers. Thus the interactions between HPCD and PEG–PPG–PEG copolymers are not strong enough to disrupt micelles and aggregates formed by those copolymers. In fact, slight synergetic deviations were observed with the micellizing copolymer, indicating the existence of ternary naphthalene/HPCD/copolymer interactions. For pharmaceutical applications, it is important that the solubilization efficacy of PEG–PPG–PEG copolymers and that of cyclodextrins modified by the 2-hydroxypropyl group would not be compromised if these two types of solubilizers were co-administered.     

Phase behavior and modeling of the poly(methyl methacrylate)–CO2–methyl methacrylate system

Cloud-point data for the system poly(methyl methacrylate) (PMMA)–CO₂–methyl methacrylate (MMA) are measured in the temperature range of 26 to 170°C, to pressures as high as 2500 bar, and with cosolvent concentrations of 10.4, 28.9, and 48.4 wt.%. PMMA does not dissolve in pure CO₂ to 255°C and 2550 bar. The cloud-point curve for the PMMA–CO₂–10.4 wt.% MMA system exhibits a negative slope that reaches 2500 bar at 105°C. With 28.9 wt.% MMA the cloud-point curve remains relatively flat at ∼900 bar for temperatures between 25 and 170°C. With 48.4 wt.% MMA the cloud-point curve exhibits a positive slope that extends to 20°C and ∼100 bar. Pressure-composition isotherms are also reported for the CO₂–MMA system at 40.0, 80.0, 105.5°C. This system exhibits type-I phase behavior with a continuous mixture–critical curve. The Peng–Robinson (PR) and SAFT equations of state model the CO₂–MMA data reasonably well without any binary interaction parameters, although the PR equation provides a better representation of the mixture-critical region. It is not possible to obtain even a qualitative fit of the PMMA–MMA–CO₂ data with the SAFT equation of state. The SAFT model qualitatively shows that the cloud-point pressure decreases with increasing MMA concentration and that the cloud-point curve exhibits a positive slope for very high concentrations of MMA in solution.     

Microstructure and hydrogen production activity of Pt–TiO2 prepared by precipitation–photodeposition

A series of Pt–TiO₂ photocatalysts were prepared by a facile precipitation–photoreduction method under different pH conditions, using H₂PtCl₆ as platinum precursor. The microstructure and chemical state of Pt loaded on the surface of TiO₂ were analyzed by X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). It was revealed that the size and distribution of Pt nanoparticles on TiO₂ surface is closely related to the initial pH of H₂PtCl₆ solution. The optimal pH value for forming highly dispersed Pt nanoparticles is 12. The photocatalytic activities of the prepared samples were investigated in terms of hydrogen production. The results indicated that the Pt–TiO₂ sample prepared by precipitation–photodeposition method shows much higher activity than that prepared by traditional photodeposition method.     

Studies of the enthalpy relaxation and the “multiple melting” behavior of semicrystalline poly(arylene ether ether ketone) (PEEk)

We report the results of an investigation by differential scanning calorimetry (DSC) of two mobility controlled processes in the amorphous phas e of semicrystalline PEEK — enthalpy relaxation below the glass transition (T _g) and secondary crystallization aboveT _g. Both result in the observation of an endothermic peak just above the annealing temperature in the DSC scan of the polymer — the enthalpy recovery peak and the low temperature melting peak, respectively. There is a striking similarity in the time and temperature dependence of the endothermic peak for these two processes. These results are reminiscent of those obtained from small strain creep studies of physical aging of semicrystalline PEEK below and aboveT _g.We gratefully acknowledge support of this work by the National Science Foundation, Science and Technology Center for High Performance Polymeric Adhesives and Composites under DMR grant 91-2004 and by an NSF Young Investigator Award (DMR 93-57512).     

Transformations of [Au(CN)2]− at the contact with activated carbon surface

We have studied the processes occurring when alkaline aqueous solution of Na[Au(CN)₂] is brought in contact with activated carbon surface. It has been shown that the adsorption of the gold cyanide complex occurs via several independent routes, one of them being accompanied with the partial breakdown of the inner sphere of the compound and free cyanide ions release into the solution. The latter process decreases the gold recovery by aqueous NaOH during the high-temperature (150°C) desorption. A prolonged storage of the adsorbent saturated with [Au(CN)₂]^? in air produces a similar result. The reasons of the observed phenomena have been discussed.     

Chemical–physical behavior of hydrogels of poly(vinyl alcohol) and poly(ethylene glycol)

New hydrogels based on polyethylene glycol (PEG) and poly(vinyl alcohol) (PVA) of different degrees of hydrolysis were synthesized. To form the network the PEG was modified at their ends with acyl chloride groups to be used as the crosslinking agent. The compositions of the hydrogels were between 50% and 90% by weight of PEG and PVA of various degrees of hydrolysis were used. It was found that the degree of hydrolysis of the PVA and the PEG content influence the equilibrium water content of the hydrogel. The process of swelling of all the hydrogels prepared followed a second-order kinetics.     

Thermodynamic modeling and experimental verification for ion-exchange synthesis of K2O·6TiO2 and TiO2 fibers from K2O·4TiO2

A thermodynamic model was established to determine ion-exchange conditions for the synthesis of potassium hexatitanate (K₂O·6TiO₂) and titanium dioxide (TiO₂) from potassium tetratitanate (K₂O·4TiO₂) fiber. In the proposed model equilibrium species in the solid phase and corresponding ion-exchange equilibrium constants at 298.15 K were determined from the experimental data of Sasaki et al. [Inorg. Chem. 24 (1985) 2265]. In order to verify the proposed model, prediction results were compared with experimental data determined in literature and those measured in this work. The comparison shows a good agreement. Based on this, the proposed model was also used to predict more extensive suitable conditions for the synthesis of K₂O·6TiO₂ and TiO₂.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Enhanced photodegradation of TiO2-containing poly(ε-caprolactone)/poly(lactic acid) blends

The calamitous accumulation of plastic waste in the environment, especially single-use disposables, calls for new approaches to materials design. One method to address the persistence of plastics beyond their intended use is to impart them with functionalities that will either allow for their recyclability or their degradation to basic natural components. This work focuses on the fabrication of photodegradable polyester blends and investigates the impact of compatibilization on photodegradation rates. Specifically, we blended poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) polymers by (reactive) extrusion in the presence or absence of dicumyl peroxide (DCP), a radical generator, and titanium dioxide (TiO₂), an inorganic photocatalyst. We examined the effects of DCP and TiO₂ loadings as well as copolymer composition on the thermomechanical properties, photodegradability, and morphology. We found that the inclusion of TiO₂ dramatically increased flexural moduli and photodegradation rates in both dry and wet conditions, while reactive compatibilization had little effect of the tested properties. This simple and scalable approach is promising to fabricate materials that can readily photodegrade.     

Thermal and Microchemical Characterisation of Sol-Gel SiO2, TiO2 and xSiO2–(1–x)TiO2 Ceramic Materials

Amorphous SiO₂, TiO₂ and xSiO₂–(1–x)TiO₂ ceramic materials with selected values of x 0.5, 0.7 and 0.9, have been prepared via sol-gel process using silicon tetraethoxysilane (TEOS) and titanium tetraisopropoxide Ti(OPri)₄. By means of the combined use of differential thermal analysis (DTA),thermogravimetry (TG), X-ray diffraction (XRD), scanning electron microscopy (SEM),X-ray photoelectron spectroscopy (XPS) and X-ray induced Auger electron spectroscopy(XAES), the surface microchemical structure and morphology of the sol-gel materials have been studied as a function of thermal treatments carried out in air up to 1200°C. In the range of temperature from 50 to 450°C, DTA-TG results evidence a remarkable mass loss due to the evaporation of organic solvents entrapped in the sol-gel materials and of the remnant organic components of the precursor metal alkoxides. In the range of temperature from 400 to about 1000°C, by means of the combined use of DTA, XRD, XPS and XAES techniques as a function of temperature and of chemical composition, it is possible to evidence the formation of crystalline phases such as quartz, anatase and rutile. Furthermore, line shape analysis of O1s XPS peak allows to distinguish between single O–Ti and O–Si bonds and also to disclose the presence of cross linking Si–O–Ti bonds, that act as bridges between SiO₂and TiO₂ moieties. As a function of temperature, Si–O–Ti bonds are broken and the formation of new Ti–O and Si–O bonds as in TiO₂ and SiO₂takes place as well as a silica segregation phenomenon. This revised version was published online in July 2006 with corrections to the Cover Date.     

Evaporation and Thermodynamic Properties of the CeO2–TiO2–ZrO2 System

Russian Journal of General Chemistry - The processes of the TiO2–CeO2–ZrO2 system evaporation were studied by high-temperature mass spectrometry. The values of the activities of TiO2...     

The effect of silane concentration on the adsorption of poly(vinyl acetate-co-maleate) and γ -methacryloxypropyl- trimethoxysilane onto E-glass fibers

The adsorption of a poly(vinyl acetate-co-maleate) (PVAM) emulsion onto E-glass fibers was investigated along with sizing formulations prepared by mixing the PVAM with varying concentrations of -methacryloxypropyltrimethoxysilane (MPS). The sized E-glass fibers were then characterized using Diffuse Reflectance Infrared Fourier Transform (DRIFT) spectroscopy, X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Loss on Ignition (LOI) along with the DRIFT spectra indicated that the addition of silane to the PVAM emulsion caused a decrease in the amount of size on the fiber. The decrease in amount of size on the E-glass fibers did not coincide with a decrease in surface coverage, instead the XPS results indicated surface coverage had increased with silane addition. These results showed that small increases in the silane concentration appear to affect the amount of size adsorbed to the E-glass fibers     

Development of polybenzoxazine–silica–titania (PBZ–SiO2–TiO2) hybrid nanomaterials with high surface free energy

In the present work, silica and titania reinforced polybenzoxazine (PBZ–SiO₂–TiO₂) hybrid nanomaterial possessing high surface free energy have been developed using dimethylol-functional benzoxazine monomer (4HBA-BZ), tetraethoxysilane (TEOS), 3-(isocyanatopropyl)triethoxysilane (ICPTS), titaniumisopropoxide (TIPO) through an in situ sol–gel process. Data obtained from the contact angle measurement indicate that the hybrid materials are hydrophilic in nature and possess a high surface free energy. For example, hybrid PBZ obtained from 1:1:0.6:0.4 (m:m:w:w) ratio of 4HBA-BZ:ICPTS:TEOS:TIPO (PBST₄) exhibit a high surface free energy of 38.2 mJm^?2 which is higher than that of neat polybenzoxazine (29.5 mJm^?2). Further data resulted from thermal studies indicate that the hybrid PBZ possess higher values of T_g, thermal stability and char yield than those of neat PBZ.