The effects of thermal annealing in NH3 -ambient on the p-type ZnO films

Thermal annealing in NH₃-ambient was carried out to form p-type ZnO films. The properties were examined by X-ray diffraction (XRD), Hall-effect measurement, photoluminescence (PL), and secondary ion mass spectrometry (SIMS). Electron concentrations in ZnO films were in the range of 10¹⁵–10¹⁷/cm³ with thermal annealing in NH₃-ambient. The activation thermal annealing process was needed at 800 C under N₂-ambient to obtain p-type ZnO. The electrical properties of the p-type ZnO showed a hole concentration of 1.06×10¹⁶/cm³, a mobility of 15.8 cm²/V s, and a resistivity of 40.18 Ω cm. The N-doped ZnO films showed a strong photoluminescence peak at 3.306 eV at 13 K, which is closely related to neutral acceptor bound excitons of the p-type ZnO. The incorporation of nitrogen was confirmed in the SIMS spectra.     

Photoluminescence, FTIR and X-ray diffraction studies on undoped and Al-doped ZnO thin films grown on polycrystalline α-alumina substrates by ultrasonic spray pyrolysis

Undoped and aluminum-doped zinc oxide (ZnO) thin films have been grown on polycrystalline α-alumina substrates by ultrasonic spray pyrolysis (USP) technique using zinc acetate dihydrate and aluminum chloride hexahydrate (Al source) dissolved in methanol, ethanol and deionized water. A number of techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and photoluminescence (PL) were used to characterize the obtained ZnO thin films. It was seen that the orientation changed with increase in substrate temperature. During the ZnO deposition Zn source reacted with polycrystalline α-Al₂O₃ substrate to form an intermediate ZnAl₂O₄ spinel layer. It has been interestingly found that the intensity of green emission at 2.48 eV remarkably increased when the obtained ZnO:Al films were deposited at 380 °C. The FTIR absorbance intensity of spectroscopic band at 447±6 cm⁻¹ is very sensitive to oxygen sublattice disorder resulting from non-stoichiometry, which is consistent with the result of PL characterization.     

Optical and electrical properties of p-type ZnO fabricated by NH3 plasma post-treated ZnO thin films

In this paper, a simple method is reported to obtain nitrogen-doped p-ZnO film. In this method NH₃ plasma, generated in a plasma-enhanced chemical vapor deposition system, was employed to treat ZnO thin film. By Hall-effect measurement, a p-type conductivity was observed for the treated film with the hole density of 2.2 × 10¹⁶ cm⁻³. X-ray photoelectron spectroscopy (XPS) results confirmed that nitrogen was incorporated into ZnO film during the treatment process to occupy the oxygen positions. In low temperature photoluminescence spectra, an emission peak corresponding to acceptor-donor pair was observed. From this emission peak we calculated the N-related acceptor binding energy to be 130 meV.     

Green photoluminescence from highly oriented ZnO thin film for photovoltaic application

We report here the fabrication of ZnO nanoparticles embedded on glass substrate by sol–gel and spin coating technique. Transmission electron microscope images revealed that the thin film is composed of ZnO nanoparticles. X-ray diffraction data confirms that the fabricated ZnO nanoparticles have hexagonal unit cell structure. The ZnO nanocrystals of the thin film are oriented along the c-axis of the hexagonal unit cell. UV–vis absorption spectroscopy shows that the absorption occurring at 373 nm in the ZnO thin film. The band gap was calculated from the absorption data and found to be 3.76 eV. This band gap enhancement occurs due to size effect in the nanoscale regime. Room temperature photoluminescence spectrum shows strong green emission at 530 nm owing to the singly ionized oxygen vacancy. This green emission was further investigated by annealing the thin film at different temperature. This singular green emission will be very useful in optoelectronic and nanophotonic devices.     

Effect of doping concentration on the structural and optical properties of pure and tin doped zinc oxide thin films by nebulizer spray pyrolysis (NSP) technique

Pure and tin doped zinc oxide (Sn:ZnO) thin films were prepared for the first time by NSP technique using aqueous solutions of zinc acetate dehydrate, tin (IV) chloride fendahydrate and methanol. X-ray diffraction patterns confirm that the films are polycrystalline in nature exhibiting hexagonal wurtzite type, with (0 0 2) as preferred orientation. The structural parameters such as lattice constant (‘a’ and ‘c’), crystallite size, dislocation density, micro strain, stress and texture coefficient were calculated from X-ray diffraction studies. Surface morphology was found to be modified with increasing Sn doping concentration. The ZnO films have high transmittance 85% in the visible region, and the transmittance is found to be decreased with the increase of Sn doping concentration. The corresponding optical band gap decreases from 3.25 to 3.08 eV. Room temperature photoluminescence reveals the sharp emission of strong UV peak at 400 nm (3.10 eV) and a strong sharp green luminescence at 528 nm (2.34 eV) in the Sn doped ZnO films. The electrical resistivity is found to be 10⁶ Ω-cm at higher temperature and 10⁵ Ω-cm at lower temperature.     

Preparation and characterization of ZnO thin films prepared by thermal oxidation of evaporated Zn thin films

In this paper, the experimental results regarding some structural, electrical and optical properties of ZnO thin films prepared by thermal oxidation of metallic Zn thin films are presented.Zn thin films (d=200–400 nm) were deposited by thermal evaporation under vacuum, onto unheated glass substrates, using the quasi-closed volume technique. In order to obtain ZnO films, zinc-coated glass substrates were isochronally heated in air in the 300–660 K temperature range, for thermal oxidation.X-ray diffraction (XRD) studies revealed that the ZnO films obtained present a randomly oriented hexagonal nanocrystalline structure. Depending on the heating temperature of the Zn films, the optical transmittance of the ZnO films in the visible wavelength range varied from 85% to 95%. The optical band gap of the ZnO films was found to be about 3.2 eV. By in situ studying of the temperature dependence of the electrical conductivity during the oxidation process, the value of about 2×10⁻² Ω⁻¹ m⁻¹ was found for the conductivity of completely oxidized ZnO films.     

Structural and optical characterisation of InN layers grown by MOCVD

In the following, we report investigations of the dependencies of the structural, optical and electrical characteristics of InN thin films grown by MOCVD on the growth temperature. The layer thicknesses range from 70 to 400 nm. Their carrier concentrations range from 7×10¹⁸ to 4×10¹⁹ cm⁻³. Hall mobility values from 150 to 1300 cm²/V/s were determined in these films. The variation of the growth temperature and V/III ratio brought about different growth modes and rates. Using TEM, in addition to measuring layer thickness, we also determined the growth mode along with the structural quality of the InN layers. The surface roughness was obtained from AFM measurements. The layer crystalline quality was also investigated by means of X-ray diffraction in the rocking mode. Photoluminescence measurements performed at room temperature and at 7 K gave emission at around 0.7 eV.     

Ag掺杂p型ZnO薄膜及其光电性能研究

采用超声喷雾热分解法在石英衬底上以醋酸锌水溶液为前驱体,以硝酸银水溶液为Ag掺杂源生长了Ag掺杂ZnO(ZnO：Ag)薄膜.研究了衬底温度对所得ZnO：Ag薄膜的晶体结构、电学和光学性质的影响规律.所得ZnO：Ag薄膜结构良好,在室温光致发光谱中检测到很强的近带边紫外发光峰,透射光谱中观测到非常陡峭的紫外吸收截止边和较高的可见光区透过率,表明薄膜具有较高的晶体质量与较好的光学特性.霍尔效应测试表明,在500℃下获得了p型导电的ZnO：Ag薄膜,载流子浓度为5.30×10¹⁵cm关键词： ZnO：Ag薄膜 p型掺杂 超声喷雾热分解 霍尔效应     

Fabrication and properties of ZnO:Cu and ZnO:Ag thin films

Thin films of ZnS and ZnO:Cu were grown by an original metal–organic chemical vapour deposition (MOCVD) method under atmospheric pressure onto glass substrates. Pulse photo-assisted rapid thermal annealing of ZnO:Cu films in ambient air and at the temperature of 700–800 C was used instead of the common long-duration annealing in a vacuum furnace. ZnO:Ag thin films were prepared by oxidation and Ag doping of ZnS films. At first a closed space sublimation technique was used for Ag doping of ZnO films. The oxidation and Ag doping were carried out by a new non-vacuum method at a temperature >500 C. Crystal quality and optical properties were investigated using X-ray diffraction (XRD), atomic force microscopy (AFM), and photoluminescence (PL). It was found that the doped films have a higher degree of crystallinity than undoped films. The spectra of as-deposited ZnO:Cu films contained the bands typical for copper, i.e. the green band and the yellow band. After pulse annealing at high temperature the 410 and 435 nm photoluminescent peaks were observed. This allows changing of the emission colour from blue to white. Flat-top ZnO:Ag films were obtained with the surface roughness of 7 nm. These samples show a strong ultraviolet (UV) emission at room temperature. The 385 nm photoluminescent peak obtained is assigned to the exciton–exciton emission.     

ZnO films grown by laser ablation with and without oxygen CVD

In the present work we have studied the properties of zinc oxide (ZnO) thin films grown by laser ablation of ZnO targets under different substrate temperature and background oxygen conditions. The ZnO layers were deposited with a Pulsed Laser Deposition (PLD) system on pre-nitrided (0001) sapphire (Al₂O₃), using the base line of a Nd:YAG laser at 1064 nm. The films were characterized by different structural and optical methods, including X-ray diffraction (XRD), scanning electron microscopy (SEM), optical transmission spectroscopy, and steady-state photoluminescence (PL). XRD analysis with rocking curves and θ–2θ scans indicates preferential growth along the c-axis direction with a full width at half maximum (FWHM) smaller than 1.5. Low-temperature photoluminescence (PL) showed strong excitonic emission near 3.36 eV between 9 and 65 K.     

Temperature dependence of excitonic luminescence from nanocrystalline ZnO films

The properties of the excitonic luminescence for nanocrystalline ZnO thin films are investigated by using the dependence of excitonic photoluminescence (PL) spectra on temperature. The ZnO thin films are prepared by thermal oxidation of ZnS films prepared by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) technique. The X-ray diffraction (XRD) indicates that ZnO thin films have a polycrystalline hexagonal wurtzite structure with a preferred (0 0 2) orientation. A strong ultraviolet (UV) emission peak at 3.26 eV is observed, while the deep-level emission band is barely observable at room temperature. The strength of the exciton-longitudinal-optical (LO) phonon coupling is deduced from the temperature dependence of the full-width at half-maximum (FWHM) of the fundamental excitonic peak, decrease in exciton-longitudinal-optical (LO) phonon coupling strength is due to the quantum confinement effect.     

A novel deposition method to grow ZnO nanorods: Spray pyrolysis

ZnO layers were deposited by chemical spray pyrolysis (CSP) using zinc chloride aqueous solutions onto indium tin oxide (ITO) glass substrates at growth temperatures in the region of 400–580 C. The layers were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and low-temperature () photoluminescence (PL) measurements. The flat film of ZnO obtained at 400 C evolves to a structured layer by raising the temperature up to 500 C. Deposition around 550 C and above results in a layer comprising well-shaped hexagonal ZnO nanorods with diameter of 100–150 nm and length of up to 1 micron. XRD shows strong c-axis orientation of ZnO being in accordance with the SEM study. Deposition of nanorods was successful using ITO with grain size around 100 nm, whereas on fine-grained ITO (grain size < 50 nm) with smooth surface fat crystals with diameter up to 400 nm and length of about 300 nm were formed. Sharp near band edge (NBE) emission peaks centered at 3.360 and 3.356 eV dominated the PL spectra of ZnO at , originating from the exciton transition bound to neutral donors. PL and XRD results suggest that ZnO rods prepared by spray pyrolysis are of high optical and crystalline quality.     

Synthesis and characterization of ZnO nano/microfibers thin films by catalyst free solution route

Zinc oxide (ZnO) nano/microfibrous thin films were successfully synthesized by a catalyst free solution route on glass and Si substrates. X-ray diffraction study revealed the formation of ZnO nanofibers of hexagonal crystalline structure. The texture coefficient of different planes varied with annealing temperature and that of the (0 0 2) plane was the highest for films annealed at temperature 873 K. Scanning electron micrograph showed the well formation of ZnO nano/microfibers with an average diameter 500 nm and having an average aspect ratio 150. UV–Vis–NIR spectroscopic study for the films deposited on glass substrates showed the high transmittance in the visible and near-infrared region. It was also observed that the band gap energy decreased as the films were annealed at higher temperature. The band gap energies of nanostructured ZnO thin films were determined to be in the range 3.03–3.61 eV. The photoluminescence study showed an UV emission peak at 397 nm, a visible blue–green emission peak at 468 nm and a green emission peak at 495 nm. Field emission properties of nanofiber ZnO thin film showed considerably low turn-on field around 1.4 V/μm. The emission current was as high as 70 μA at the field of 3.6 V/μm.     

Photoluminescence of ZnO nanostructures grown by the aqueous chemical growth technique

Zinc oxide nanostructured films were grown by the aqueous chemical growth technique using equimolar aqueous solutions of zinc nitrate and hexamethylenetetramine as precursors. Silicon(100) and glass substrates were placed in Pyrex glass bottles with polypropylene autoclavable screw caps containing the precursors described above, and heated at 95 C for several hours. X-ray diffraction 2θ/θ scans showed that the only crystallographic phase present was the hexagonal wurtzite structure. Scanning electron microscopy showed the formation of flowerlike ZnO nanostructures, consisting of hexagonal nanorods with a diameter of a few hundred nanometers. The photoluminescence spectra of the ZnO nanostructures were recorded at 18–295 K using a cw He–Cd laser (325 nm) and a pulsed laser (266 nm). The ZnO nanostructures exhibit an ultraviolet emission band centered at 3.192 eV in the vicinity of the band edge, which is attributed to the well-known excitonic transition in ZnO.     

The field emission of indium-doped ZnO films fabricated by room temperature DC magnetron sputtering

Indium doped ZnO film was fabricated at room temperature by co-sputtering a zinc target and an indium plate under the flow of oxygen and argon. The film was then characterized and the field emission of the film was studied. The indium composition x in the film (Zn_1−xIn_xO) is 5%. The film is hexagonal without any secondary phases or precipitates. The film has two major emission peaks, one related to the band edge emission and another possibly related to the electron acceptor transition. The possible acceptor is nitrogen occupying oxygen site in ZnO. The film is n-type and very resistive. The turn on field of the film at an emission current density of 10 μA/cm² is 17.5 V/μm. The relatively weak field emission property is due to the unintentional incorporation of acceptors such as substitutional nitrogen and oxygen vacancies, which increase the work function of ZnO by reducing the electron density and lowering the Fermi level position of the ZnO:In film.     

Cesium doped and undoped ZnO nanocrystalline thin films: a comparative study of structural and micro‐Raman investigation of optical phonons

Undoped and cesium‐doped zinc oxide (ZnO) thin films have been deposited on sapphire substrate (0001) using the sol–gel method. Films were preheated at 300 °C for 10 min and annealed at 600 and 800 °C for 1 h. The grown thin films were confirmed to be of wurtzite structure using X‐ray diffraction. Surface morphology of the films was analyzed using scanning electron microscopy. The photoluminescence (PL) spectra of ZnO showed a strong ultraviolet (UV) emission band located at 3.263 eV and a very weak visible emission associated with deep‐level defects. Cesium incorporation induced a blue shift of the optical band gap and quenching of the near‐band‐edge PL for nanocrystalline thin film at room temperatures because of the band‐filling effect of free carriers. A shift of about 10–15 cm⁻¹ is observed for the first‐order longitudinal‐optical (LO) phonon Raman peak of the nanocrystals when compared to the LO phonon peak of bulk ZnO. The UV resonant Raman excitation at RT shows multiphonon LO modes up to fifth order. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis, characterization, growth mechanism, photoluminescence and field emission properties of novel dandelion-like gallium nitride

Dandelion-like gallium nitride (GaN) microstructures were successfully synthesized via Ni catalyst assisted chemical vapor deposition method at 1200 °C under NH₃ atmosphere by pre-treating precursors with aqueous ammonia. The as-synthesized product was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). X-ray diffraction analysis revealed that as-synthesized dandelion-like GaN was pure and has hexagonal wurtzite structure. SEM results showed that the size of the dandelion-like GaN structure was in the range of 30-60 μm. Dandelion-like GaN microstructures exhibited reasonable field emission properties with the turn-on field of 9.65 V μm⁻¹ (0.01 mA cm⁻²) and threshold field of 11.35 V μm⁻¹ (1 mA cm⁻²) which is sufficient for applications of electron emission devices, field emission displays and vacuum micro electronic devices. Optical properties were studied at room temperature by using fluorescence spectrophotometer. Photoluminescence (PL) measurements of dandelion-like GaN showed a strong near-band-edge emission at 370.2 nm (3.35 eV) with blue band emission at 450.4 nm (2.75 eV) and 465.2 nm (2.66 eV) but with out yellow band emission. The room-temperature photoluminescence properties showed that it has also potential application in light-emitting devices. The tentative growth mechanism for the growth of dandelion-like GaN was also described.     

Determination of electrical types in the P-doped ZnO thin films by the control of ambient gas flow

Phosphorus (P)-doped ZnO thin films with amphoteric doping behavior were grown on c-sapphire substrates by radio frequency magnetron sputtering with various argon/oxygen gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio without post-annealing. The P-doped ZnO films grown at a argon/oxygen ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of 1.5 × 10¹⁷ cm⁻³ and 2.5 cm²/V s, respectively. X-ray diffraction showed that the ZnO (0 0 0 2) peak shifted to lower angle due to the positioning of P³⁻ ions with a larger ionic radius in the O²⁻ sites. This indicates that a p-type mechanism was due to the substitutional P_O. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction light emitting diode showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.     

Mn doped ZnO nanostructured thin films prepared by ultrasonic spray pyrolysis method

Mn-doped ZnO thin films with different percentage of Mn content (0, 1, 3 and 5 at.%) and substrate temperature of 350 °C, were deposited by a simple ultrasonic spray pyrolysis method under atmospheric pressure. We have studied the structural and optical properties by using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and ultra-violet visible near infrared (UV–Vis-NIR) spectroscopy. The lattice parameters calculated for the Mn-doped ZnO from XRD pattern were found to be slightly larger than those of the undoped ZnO, which indicate substitution of Mn in ZnO lattice. Compared with the Raman spectra for ZnO pure films, the Mn-doping effect on the spectra is revealed by the presence of additional peak around 524 cm⁻¹ due to Mn incorporation. With increasing Mn doping the optical band gap increases indicating the Burstein–Moss effect.     

Quenching of surface traps in Mn doped ZnO thin films for enhanced optical transparency

The structural and photoluminescence analyses were performed on un-doped and Mn doped ZnO thin films grown on Si (1 0 0) substrate by pulsed laser deposition (PLD) and annealed at different post-deposition temperatures (500-800 °C). X-ray diffraction (XRD), employed to study the structural properties, showed an improved crystallinity at elevated temperatures with a consistent decrease in the lattice parameter ‘c’. The peak broadening in XRD spectra and the presence of Mn 2p3/2 peak at ∼640 eV in X-ray Photoelectron Spectroscopic (XPS) spectra of the doped thin films confirmed the successful incorporation of Mn in ZnO host matrix. Extended near band edge emission (NBE) spectra indicated the reduction in the concentration of the intrinsic surface traps in comparison to the doped ones resulting in improved optical transparency. Reduced deep level emission (DLE) spectra in doped thin films with declined PL ratio validated the quenching of the intrinsic surface traps thereby improving the optical transparency and the band gap, essential for optoelectronic and spintronic applications. Furthermore, the formation and uniform distribution of nano-sized grains with improved surface features of Mn-doped ZnO thin films were observed in Field Emission Scanning Electron Microscopy (FESEM) images.