电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

Decomposition of P2S2N4(Si(CH3)3)4A12C14 as Studied by FT-Raman and Quantum Chemistry Means

The dimeric title compound decomposes upon heating to give the monomer and desulphurized monomer as shown by FT-Raman and quantum chemical means.     

M5(PO4)3F (M=Ca, Sr, Ba)中Sm3+的电荷迁移态及Sm3+和Eu3+的电荷迁移能量关系

采用高温固相反应合成了M_5-2xSm_xNa_x(PO₄)₃F(M=Ca,Sr,Ba)荧光体,研究了其在真空紫外-可见光范围的发光特性。发现在Ca₅(PO₄)₃F中Sm³⁺的电荷迁移带约在191 nm,在Sr₅(PO₄)₃F中约在199 nm,而在Ba₅(PO₄)₃F中约在204 nm,随着被取代碱土离子半径的增大电荷迁移能量逐渐减小。比较了M₅(PO₄)₃F (M=Ca,Sr,Ba)中Sm³⁺和Eu³⁺电荷迁移能量的关系。     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

Near infrared study of aqueous lanthanide perchlorates

The near infrared spectra of water in aqueous solutions of La(ClO₄)₃, Pr(ClO₄)₃, Nd(ClO₄)₃, Gd(ClO₄)₃, Er(ClO₄)₃, Yb(ClO₄)₃, Lu(ClO₄)₃, and NaClO₄ have been measured in the concentration range from 0.3 to 2.5 mol-dm^–3, at 25°C. The relative contents of free OH groups in the 1.0, 1.6, and 2.2M solutions have been calculated from extinction coefficients for water at 1160 nm. They increase with increasing salt concentration and are greater in solutions of the lighter lanthanide perchlorates at any fixed molarity. The results are discussed in terms of the stoichiometry and structure of hydrated cations of trivalent lanthanides.     

Syntheses and characterization of two oxoborates, (Pb3O)2(BO3)2MO4 (M=Cr, Mo)

Two oxoborates, (Pb₃O)₂(BO₃)₂MO₄ (M=Cr, Mo), have been prepared by solid-state reactions below 700 °C. Single-crystal XRD analyses showed that the Cr compound crystallizes in the orthorhombic group Pnma with a=6.4160(13) Å, b=11.635(2) Å, c=18.164(4) Å, Z=4 and the Mo analog in the group Cmcm with a=18.446(4) Å, b=6.3557(13) Å, c=11.657(2) Å, Z=4. Both compounds are characterized by one-dimensional chains formed by corner-sharing OPb₄ tetrahedra. BO₃ and CrO₄ (MoO₄) groups are located around the chains to hold them together via Pb–O bonds. The IR spectra further confirmed the presence of BO₃ groups in both structures and UV–vis diffuse reflectance spectra showed band gaps of about 1.8 and 2.9 eV for the Cr and Mo compounds, respectively. Band structure calculations indicated that (Pb₃O)₂(BO₃)₂MoO₄ is a direct semiconductor with the calculated energy gap of about 2.4 eV.     

Solid-solid interactions in pure and Li2O-doped manganese and magnesium mixed oxides system

The solid-solid interactions between manganese and magnesium oxides in absence and in presence of small amounts of Li₂O have been investigated. The molar ratios between manganese and magnesium oxides in the form of Mn₂O₃ and MgO were varied between 0.05:1 to 0.5:1. The mixed solids were calcined in air at 400-1000°C. The techniques employed were DTA, XRD and H₂O₂ decomposition at 20-40°C.The results obtained revealed that solid-solid interactions took place between the reacting solids at 600-1000°C yielding magnesium manganates (Mg₂MnO₄, Mg₆MnO₈, MgMnO₄ besides unreacted portions of MgO, Mn₂O₃ and Mn₃O₄). Li₂O-doping (0.75-6 mol%) of the investigated system followed by calcination at 600 and 800°C decreased progressively the intensity of the diffraction lines of Mn₂O₃ (Bixbyite) with subsequent increase in the lattice parameter 'a' of MgO to an extent proportional to the amount of Li₂O added. This finding might suggest that the doping process enhanced the dissolution of Mn₂O₃ in MgO forming solid solution. This treatment led also to the formation of Li₂MnO₃. Furthermore, the doping with 3 and 6 mol% Li₂O conducted at 800°C resulted in the conversion of Mn₂O₃ into Mn₃O₄, a process that took place at 1000°C in absence of Li₂O. The produced Li₂MnO₃ phase remained stable by heating at up to 1000°C. Furthermore, Li₂O doping of the investigated system at 400-1000°C resulted in a progressive measurable increase in the particle size of MgO.The catalytic activity measurements showed that the increase in the molar ratio of Mn₂O₃ in the samples precalcined at 400-800°C was accompanied by a significant increase in the catalytic activity of the treated solids. The maximum increase in the catalytic activity expressed as reaction rate constant measured at 20°C (k _20°C) attained 3.14, 2.67 and 3.25-fold for the solids precalcined at 400, 600 and 800°C, respectively. Li₂O-doping of the samples having the formula 0.1 Mn₂O₃/MgO conducted at 400-600°C brought a progressive significant increase in its catalytic activity. The maximum increase in the value of k _20°C due to Li₂O attained 1.93 and 2.75-fold for the samples preheated at 400 and 600°C, respectively and opposite effect was found for the doped samples preheated at 800°C.This revised version was published online in November 2005 with corrections to the Cover Date.     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Simultaneous thermoanalytical investigations of (C6H5)4AsCl and (C6H5)4PCl under air and argon atmospheres

The thermoanalytical curves of (C₆H₅)₄AsCl (I) and (C₆H₅)₄PCl (II) were generated simultaneously by using a Netzsch simultaneous thermal analyser 409 under static air and dynamic argon atmospheres. The ranges of thermal stability of I and II were found to be 145–310°C and 137–365°C, respectively, and their melting points to be 261 and 278°C. The DTA profiles of I and II differ and can be used for their distinction.     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

ZrW1.7ⅥW0.3ⅤO7H0.3(OH)2·2H2O的合成与表征

分别利用微乳液水热法和酸蒸气水热法合成了杂多蓝化合物ZrW1.7ⅥW0.3ⅤO7H0.3(OH)2·2H2O.XRD测定结果表明,该化合物与ZrMo2O7(OH)2·2H2O具有相同晶体结构类型.使用Rietveld方法对产物进行了结构精修,并计算出了键参数和键价.运用EPR技术测定了该化合物中W的价态,并利用XPS能谱测定了W/W的比例.利用价键和规则,指出ZrW1.7ⅥW0.3ⅤO7H0.3(OH)2·2H2O中的W—O3—H0.15存在羟基化现象,并对杂多蓝化合物的红外吸收光谱进行了指认.     

电池正极材料Li3V2(PO4)3/C的水热合成和性能

以LiOH·H2O, NH4VO3, NH4H2PO4 和麦芽糖等为原料, 采用水热法合成了碳包覆的磷酸钒锂化合物, 考察了碳含量对材料电化学性能的影响. 利用XRD, TEM, SEM和恒流充放电测试等手段对产物的结构、 形貌和电化学性能进行表征. 结果表明, 在650℃煅烧的样品为单一纯相的单斜晶体结构. 晶体颗粒分布为100~300 nm, 粒度分散均匀, 分散性良好, 无团聚现象, 且在颗粒表面包覆了一层无定形碳, 这有利于改善材料的导电率. 含碳量为10.23%的样品, 在倍率1.0C的电流密度下, 在3.0~4.3 V电压范围内, 样品的首次放电比容量高达118.8 mA·h/g, 循环15圈后放电比容量为115.1 mA·h/g, 容量保持率为96.88%.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇结构及其热力学性质

用HF自洽场理论和密度泛函理论(DFT)的B3LYP方法,在6 31G水平上研究了低聚物(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇的几何构型、电子结构和聚合反应热力学性质,比较了两个系列化合物中化学键的强度.结果表明,Cl2AlNH2和H2AlNH2分子为C2 (EC)平面型结构,其中Al－N为由一个σ键和一个键组成的双键.(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)分子为Dnh对称,Al－N是典型的σ单键 .低聚物(Cl2AlNH2)n和(H2AlNH2)n的稳定性顺序分别为: 3 > 2 > 4> 5 > 1和8 > 7 > 9 > 11 > 6.     

Reactivity of Binary Mixtures of La(III) Oxide and Cu(II) Oxalate or Nitrate and Synthesis of La(III) Cuprate

Reactivity of mixtures of La(III) oxide and Cu(II) oxalate/nitrate in hydrated as well as anhydrous state was studied using TG, DTA and XRD. Cu(II) oxide formed in the endothermic decomposition of mixture containing hydrated Cu(II) nitrate and La(III) oxide could not form La₂CuO₄ while Cu(II) oxide formed in the exothermic decomposition of mixture containing hydrated/anhydrous Cu(II) oxalate and La(III) oxide reacts with La(III) oxide and develops the phases CuLaO₃ and La₂CuO₄. The maximum reactivity with respect to the formation of La₂CuO₄phase was observed in mixture containing anhydrous Cu(II) oxalate. This revised version was published online in July 2006 with corrections to the Cover Date.