等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Decorating Channel Walls in Metal–Organic Frameworks with Crown Ethers for Efficient and Selective Separation of Radioactive Strontium(II)

Nuclear accidents and the improper disposal of nuclear wastes have led to serious environmental radioactive pollutions. The rational design of adsorbents for the highly efficient separation of strontium(II) is essential in treating nuclear waste and recovering radioactive strontium resources. Metal–organic frameworks (MOFs) are potential materials for the separation of aqueous metal ions owing to their designable structure and tunable functionality. Herein, a novel 3D MOF material MOF-18Cr6, in which 1D channels are formed using 18-crown-6-ether-containing ligands as channel walls, is fabricated for strontium(II) separation. In contrast to traditional MOFs designed by grafting functional groups in the framework pores, MOF-18Cr6 possesses regular 18-crown-6-ether cavities on the channel walls, which not only can transport and intake strontium(II) via the channels, but also prevent blockage of the channels after the binding of strontium(II). Consequently, the functional sites are fully utilized to achieve a high strontium(II) removal rate of 99.73 % in simulated nuclear wastewater. This study fabricates a highly promising adsorbent for the separation of aqueous radioactive strontium(II), and more importantly, can provide a new strategy for the rational design of high-performance MOF adsorbents for separating target substances from complex aqueous environments.     

金属有机框架材料吸附性能应用的研究

金属有机框架材料(MOFs)是一种多孔聚合物材料,其相关研究近年来取得迅速发展。MOFs是以金属离子为中心,桥连的有机配体作为支撑经延伸形成的一类具有周期性网络结构的晶态多孔材料[1]。由于其较强的功能性、较高的比表面积、超高的孔隙率以及可调控的孔道结构[2],MOFs在储气、分离、催化、载药和光学等领域受到了极大的重视,并具有广泛的应用前景。本文从MOFs材料的结构设计出发,介绍近几年MOFs材料在能源气体(H2、CH4)的储存,H2S、CO2、有机气体分子的捕集以及医学领域(对于一些药物的吸附装载)的研究进展,并对MOFs材料在应用上存在的问题进行了阐述,对其未来的发展趋势作出展望。     

Recent Progress in Metal-Organic Framework Based Fluorescent Sensors for Hazardous Materials Detection

Population growth and industrial development have exacerbated environmental pollution of both land and aquatic environments with toxic and harmful materials. Luminescence-based chemical sensors crafted for specific hazardous substances operate on host-guest interactions, leading to the detection of target molecules down to the nanomolar range. Particularly, the luminescence-based sensors constructed on the basis of metal-organic frameworks (MOFs) are of increasing interest, as they can not only compensate for the shortcomings of traditional detection techniques, but also can provide more sensitive detection for analytes. Recent years have seen MOFs-based fluorescent sensors show outstanding advantages in the field of hazardous substance identification and detection. Here, we critically discuss the application of MOFs for the detection of a broad scope of hazardous substances, including hazardous gases, heavy metal ions, radioactive ions, antibiotics, pesticides, nitro-explosives, and some harmful solvents as well as luminous and sensing mechanisms of MOF-based fluorescent sensors. The outlook and several crucial issues of this area are also discussed, with the expectation that it may help arouse widespread attention on exploring fluorescent MOFs (LMOFs) in potential sensing applications.     

Metal-Organic Frameworks for Hydrogen Energy Applications: Advances and Challenges

Hydrogen is in limelight as an environmental benign alternative to fossil fuels from few decades. To bring the concept of hydrogen economy from academic labs to real world certain challenges need to be addressed in the areas of hydrogen production, storage, and its use in fuel cells. Crystalline metal-organic frameworks (MOFs) with unprecedented surface areas are considered as potential materials for addressing the challenges in each of these three areas. MOFs combine the diverse chemistry of molecular linkers with their ability to coordinate to metal ions and clusters. The unabated flurry of research using MOFs in the context of hydrogen energy related activities in the past decade demonstrates the versatility of this class of materials. In the present review, we discuss major strategical advances that have taken place in the field of “hydrogen economy and MOFs” and point out issues requiring further attention.     

二维导电金属有机骨架材料

金属有机骨架(MOFs)是由金属离子或簇与有机配体以配位键组装而成的晶态多孔材料,其高的孔隙率及功能可设计性使其广泛应用于各种领域.然而,传统MOFs多数电导率非常低,这严重制约了其在电学相关领域的发展.近年来,导电金属有机骨架尤其是二维导电金属有机骨架(2D ECMOFs)材料因其结构中独特的π-π堆积及π-d共轭作...     

类水滑石材料在核废水处理领域的应用

核能已成为我国能源结构的重要组成部分, 但含放射性物质的废水所带来的危害不容忽视. 如何高效解决核废水污染问题迫在眉睫. 类水滑石材料是一类阴离子型粘土化合物, 因其层板组成及层间阴离子种类的可调控性、 较大的比表面积及粒径和形貌的可调控性等特点已在含放射性核素废水的处理中崭露头角. 本文主要阐述了类水滑石材料对废水中放射性核素的吸附行为及其作用机制, 探讨了存在的问题及可能的解决方法, 并对其发展前景进行了展望.     

金属有机框架材料在分离分析领域的研究进展

金属有机框架材料是由金属离子节点和有机配体通过配位键连接形成的具有序多孔骨架的材料, 因其具有比表面积大、 孔隙可调及表面性质可控等优点而备受关注. 通过对有机配体和金属离子进行选择及对金属有机框架材料进行后修饰处理, 可实现对金属有机框架材料表面性质的调控, 以提升其选择性吸附及特异性识别等性能, 进而拓展其在分离分析等领域的应用. 本文从金属有机框架材料的表面性质调控出发, 介绍了其表面性质与分离分析性能的关系, 总结了近年来该领域的代表性工作, 并展望了金属有机框架材料在分离分析领域的应用前景.     

The Legacy and Future of Radioactive Waste Management at the Millennium

Wastes containing radioactive materials have been produced ever since ore recovery and processing began; however, such materials did not become of public concern until the large-scale activities involving uranium and thorium ores and nuclear fission during and after World War II. Efforts to provide disposal sites for radioactive wastes, especially those associated with nuclear weapons and nuclear energy, have been largely unsuccessful for the past 40 years or so and are nearing crisis proportions as the new millennium begins — its eventual resolution is believed to require greater reliance on stewardship and a larger governmental presence.     

Advances of Metal‐Organic Frameworks in Energy and Environmental Applications

Nowadays, energy shortage and environmental pollution issues are increasingly severe and urgent to be solved. The effective storage and use of environmentally friendly fuels and removal of harmful gases from the environment are great challenges and of great importance both for the environment protection and for human health. Porous metal‐organic frameworks (MOFs) are highly ordered crystalline materials formed by the self‐assembly process of metal ions and organic ligands. Their good features such as ultrahigh porosity, large surface area, structural diversity and functionalities make them promising candidates for applications in energy and environmental fields. MOF thin films and MOF composites have also been investigated to further enhance the properties and introduce new functionalities. This review provides an overview of the synthesis methods of pristine MOFs, MOF thin films and MOF composites, and significant advances of MOFs in energy and environment applications such as energy storage (H₂, CH₄), CO₂ capture and separation, adsorption removal and sensing of harmful gases in the environment.     

金属有机框架与新型载药体系

金属-有机骨架材料(MOFs)是一类由金属离子与有机配体之间的配位自组装形成的新型多孔复合材料。因其具有高比表面积、可调的尺寸、拓扑结构多样性、合成简便、有机基团易于功能化等优点使其在生物分析、成像、传感、催化、气体存储与分离以及药物运载等领域具有广泛的应用前景。这里通过简要介绍MOFs的研究背景,基于MOFs孔径的药物装载策略以及MOFs药物释放的刺激响应方式,阐述MOFs作为药物递送载体的最新进展,为后期药物载体的设计提供参考。