Automated nanoliter solution deposition for total reflection X-ray fluorescence analysis of semiconductor samples

In this study, a BioDot BioJet dispensing system was investigated as a nanoliter sample deposition method for total reflection X-ray fluorescence (TXRF) analysis. The BioDot system was programmed to dispense arrays of 20 nL droplets of sample solution on Si wafers. Each 20 nL droplet was approximately 100 μm in diameter. A 10 × 10 array (100 droplets) was deposited and dried in less than 2 min at room temperature and pressure, demonstrating the efficiency of the automated deposition method. Solutions of various concentrations of Ni and Ni in different matrices were made from stock trace element standards to investigate of the effect of the matrix on the TXRF signal. The concentrations were such that the levels of TXRF signal saturation could be examined. Arrays were deposited to demonstrate the capability of drying 100 μL of vapor phase decomposition-like residue in the area of a typical TXRF detector.     

A new technique for the deposition of standard solutions in total reflection X-ray fluorescence spectrometry (TXRF) using pico-droplets generated by inkjet printers and its applicability for aerosol analysis with SR-TXRF

A new technique for the deposition of standard solutions on particulate aerosol samples using pico-droplets for elemental determinations with total reflection X-ray fluorescence spectrometry (TXRF) is described. It enables short analysis times without influencing the sample structure and avoids time consuming scanning of the sample with the exciting beam in SR-TXRF analysis. Droplets of picoliter volume (∼ 5–130 pL) were generated with commercially available and slightly modified inkjet printers operated with popular image processing software. The size of the dried droplets on surfaces of different polarity namely silicone coated and untreated quartz reflectors, was determined for five different printer types and ten different cartridge types. The results show that droplets generated by inkjet printers are between 50 and 200 μm in diameter (corresponding to volumes of 5 to 130 pL) depending on the cartridge type, which is smaller than the width of the synchrotron beam used in the experiments (< 1 mm at an energy of 17 keV at the beamline L at HASYLAB, Hamburg). The precision of the printing of a certain amount of a single element standard solution was found to be comparable to aliquoting with micropipettes in TXRF, where for 2.5 ng of cobalt relative standard deviations of 12% are found. However, it could be shown that the printing of simple patterns is possible, which is important when structured samples have to be analysed.     

A study on solution deposited CuSCN thin films: Structural,electrochemical, optical properties

A cost-effective successive ionic layer adsorption and reaction (SILAR) method was used to deposit copper (I) thiocyanate (CuSCN) thin films on glass and steel substrates for this study. The deposited thin films were characterized for their structural, morphological, optical and electrochemical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectroscopy and VersaSTAT potentiostat. A direct band gap of 3.88 eV and 3.6 eV with film thickness of 0.7 μm and 0.9 μm was obtained at 20 and 30 deposition cycles respectively. The band gap, microstrain, dislocation density and crystal size were observed to be thickness dependent. The specific capacitance of the CuSCN thin film electrode at 20 mV/s was 760 F g⁻¹ for deposition 20 cycles and 729 F g⁻¹ for deposition 30 cycles.     

Fabrication of solid thin film electrolyte and LiCoO2 by aerosol flame pyrolysis deposition

Aerosol flame pyrolysis deposition method was applied to deposit the oxide glass electrolyte film and LiCoO₂ cathode for thin film type Li-ion secondary battery. The thicknesses of as-deposited porous LiCoO₂ and Li₂O–B₂O₃–P₂O₅ electrolyte film were about 6 μm and 15 μm, respectively. The deposited LiCoO₂ was sintered for 2 min at 700 °C to make partially densified cathode layer, and the deposited Li₂O–P₂O₅–B₂O₃ glass film completely densified by the sintering at 700 °C for 1 h. After solid state sintering process the thicknesses were reduced to approximately 4 μm and 6 μm, respectively. The cathode and electrolyte layers were deposited by continuous deposition process and integrated into a layer by co-sintering. It was demonstrated that Aerosol flame deposition is one of the good candidates for the fabrication of thin film battery.     

Electrodeposition of hyaluronic acid and hyaluronic acid–bovine serum albumin films from aqueous solutions

Hyaluronic acid (HYH) films were prepared from aqueous sodium hyaluronate (HYNa) solutions by anodic electrodeposition. The film thickness was varied in the range of 0–20 μm by the variation of the deposition time and HYNa concentration. The deposition rate was low at HYNa concentration below 1 g L⁻¹ and increased significantly in the range of 3–5 g L⁻¹. The addition of bovine serum albumin (BSA) to the HYNa solutions resulted in increased deposition yield, which was attributed to the formation of composite HYH–BSA films. The thickness of the HYH–BSA films deposited by anodic electrodeposition was varied in the range of 0–80 μm. The HYH and composite HYH–BSA films were studied by scanning electron microscopy, thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy and circular dichroism spectroscopy. The deposition mechanism and kinetics of deposition are discussed.     

Preparation of vertically-aligned nickel nanowires with anodic aluminum oxide templates and their application as field emitters

In this study, well-ordered and vertically-aligned nickel nanowires (NiNWs) with a controllable length were grown inside the nanopores of anodic alumina oxide templates (AAOTs) using a simple electrochemical deposition (ECD) method. The electron field emission characteristics of the prepared NiNWs within AAOTs with two pore diameters (100 and 200 nm) and length in the range of 2.7–22 μm were measured and discussed. The turn-on field/the enhancement factor of 8.5 and 7-μm-long NiNWs prepared within 100 and 200 pore diameter AAOTs, respectively, were about 3.46 V/μm/17,621 and 4.8 V/μm/5001, respectively, according to I–V measurements.     

A new X-ray pinhole camera for energy dispersive X-ray fluorescence imaging with high-energy and high-spatial resolution

A new X-ray pinhole camera for the Energy Dispersive X-ray Fluorescence (ED-XRF) imaging of materials with high-energy and high-spatial resolution, was designed and developed. It consists of a back-illuminated and deep depleted CCD detector (composed of 1024 × 1024 pixels with a lateral size of 13 μm) coupled to a 70 μm laser-drilled pinhole-collimator, positioned between the sample under analysis and the CCD. The X-ray pinhole camera works in a coaxial geometry allowing a wide range of magnification values.The characteristic X-ray fluorescence is induced on the samples by irradiation with an external X-ray tube working at a maximum power of 100 W (50 kV and 2 mA operating conditions).The spectroscopic capabilities of the X-ray pinhole camera were accurately investigated. Energy response and energy calibration of the CCD detector were determined by irradiating pure target-materials emitting characteristic X-rays in the energy working-domain of the system (between 3 keV and 30 keV).Measurements were performed by using a multi-frame acquisition in single-photon counting. The characteristic X-ray spectra were obtained by an automated processing of the acquired images. The energy resolution measured at the Fe–Kα line is 157 eV.The use of the X-ray pinhole camera for the 2D resolved elemental analysis was investigated by using reference-patterns of different materials and geometries. The possibility of the elemental mapping of samples up to an area of 3 × 3 cm² was demonstrated.Finally, the spatial resolution of the pinhole camera was measured by analyzing the profile function of a sharp-edge. The spatial resolution determined at the magnification values of 3.2 × and 0.8 × (used as testing values) is about 90 μm and 190 μm respectively.     

Analysis of total and dissolved heavy metals in surface water of a Mexican polluted river by total reflection X-ray fluorescence spectrometry

The present area of study is located in the Upper Course of the Lerma River (UCLR). The Lerma is one of the most important rivers of Mexico, where it drains highly populated and industrialized regions. The aim of the present study is to determine the heavy metal concentration of Cr, Mn, Fe, Cu and Pb in dissolved and total phases of the UCLR by means of Total Reflection X-ray Fluorescence Spectrometry (TXRF). The surface water samples were collected at 8 sites distributed following the stream flow direction of the river. Four sampling campaigns were carried out in each site in a 1-year period. A sample preparation method was applied in order to obtain the total and dissolved fraction and to destroy the organic matter. The total heavy metal average concentration decrease in the following order: Fe (2566 μg/L) > Mn (300 μg/L) > Cu (66 μg/L) > Cr (21 μg/L) > Pb (15 μg/L). In general, the heavy metal concentrations in water of the UCLR are below the maximum permissible limits.     

Sputtered,electroless, and rolled palladium–ceramic membranes

Three techniques were used to produce palladium–ceramic (Pd–ceramic) composite membranes for hydrogen separation and production. They are sputtering, electroless deposition and rolling of thin Pd alloy films over ceramic porous tubes.After studying and developing the three coating techniques, an extensive testing and characterizing work was carried out on these thin film composite membranes. The results show that in the sputtered (0.5–5 μm) and electroless (2.5–20 μm) composite membranes, the thermal cycling of the hydrogenated metallic layer produces membrane failures. Such failures are characterized by crack formation and metal film peeling. This fact has been explained by an evaluation of the shear stresses at the metal–ceramic interface due to the differential elongation between the palladium (Pd) coating and the ceramic support under thermal cycling and hydrogen loading. The rolled membranes (50–70 μm), however, because of the particular coating solution, have shown a complete hydrogen selectivity and good chemical and physical stability in long-term tests.     

The wet phase separation: the effect of cast solution thickness on the appearance of macrovoids in the membrane forming ternary cellulose acetate/acetone/water system

We report on novel observations on the appearance of macrovoids in the ternary cellulose acetate (CA)/acetone (ACE)/water membrane forming system. The membranes are prepared by the wet phase separation whereby the cast solution is composed of ACE and polymer, and the coagulation bath is pure water only. It is found that the macrovoid formation in a 12.5 wt.% cast solution strongly depends on the cast solution thickness: macrovoids appear at the thickness of 500 μm but not at 150 and 300 μm.     

Analytical determination of selenium in medical samples,staple food and dietary supplements by means of total reflection X-ray fluorescence spectroscopy

Selenium is essential for many aspects of human health and, thus, the object of intensive medical research. This demands the use of analytical techniques capable of analysing selenium at low concentrations with high accuracy in widespread matrices and sometimes smallest sample amounts.In connection with the increasing importance of selenium, there is a need for rapid and simple on-site (or near-to-site) selenium analysis in food basics like wheat at processing and production sites, as well as for the analysis of this element in dietary supplements. Common analytical techniques like electrothermal atomic absorption spectroscopy (ETAAS) and inductively-coupled plasma mass spectrometry (ICP-MS) are capable of analysing selenium in medical samples with detection limits in the range from 0.02 to 0.7 μg/l. Since in many cases less complicated and expensive analytical techniques are required, TXRF has been tested regarding its suitability for selenium analysis in different medical, food basics and dietary supplement samples applying most simple sample preparation techniques.The reported results indicate that the accurate analysis of selenium in all sample types is possible. The detection limits of TXRF are in the range from 7 to 12 μg/l for medical samples and 0.1 to 0.2 mg/kg for food basics and dietary supplements. Although this sensitivity is low compared to established techniques, it is sufficient for the physiological concentrations of selenium in the investigated samples.     

Preparation of a palladium alloy composite membrane supported in a porous stainless steel by vacuum electrodeposition

Pinhole-free palladium/nickel (Pd/Ni) alloy membranes deposited on a porous stainless steel (SUS) support have been fabricated. The deposition was made by vacuum electrodeposition technique which could produce the alloy film less than 1 μm thick. This technique allows for the Pd/Ni alloy by employing Pd/Ni complex reagent, and typical Pd/Ni plating had compositions of 78% Pd and 22% Ni. In order to make the surface smooth and enhance the adhesive bond between the top layer and the substrate, a nascent porous SUS disk was treated sequently with submicron nickel powder and CuCN solution. The important parameters that can affect deposition were pore size, defects, and surface roughness of substrate. The membranes were characterized by permeation experiments with hydrogen and nitrogen at temperatures ranging from 623 to 823 K and pressures from 10.3 to 51.7 cmHg. The composite membranes prepared in this technique yielded excellent separation performance for hydrogen: hydrogen permeance of 5.79×10⁻² cm³/cm² cmHg s and hydrogen/nitrogen (H₂/N₂) selectivity was 4700 at 823 K.     

Effects of disordered hemispherical micropatterns on Staphylococcus epidermidis biofilm formation

Surfaces which have physical patterns in the scale of bacteria cells have been shown to influence the microorganism's adhesion and biofilm formation characteristics. Layer-by-layer self-assembly was utilized to create disordered hemispherical patterns on poly(dimethylsiloxane) with a feature size of 0.5 μm, 1.0 μm and 2.0 μm. The effects of pattern size on the retention and biofilm formation of Staphylococcus epidermidis were examined as a function of culture time. The 1.0 μm pattern significantly reduced biofilm surface coverage by ～30% after 5 h of culture in comparison to that on an unpatterned surface while the effect of the 0.5 and 2.0 μm patterns was negligible. On the 1.0 μm surface, bacteria initially adhered on the unpatterned areas of the disordered surface and subsequently developed into biofilms by spreading across the unpatterned areas while avoiding those covered by the pattern. The results suggest that the size of surface patterns is an important factor in altering bacteria adhesion and biofilm formation characteristics.     

Factors affecting membrane fouling reduction by surface modification and backpulsing

Several factors affecting microfiltration membrane fouling and cleaning, including backpulsing, crossflushing, backwashing, particle size, membrane surface chemistry, and ionic strength, were investigated with suspensions of latex beads. Approximately two-fold permeate volume enhancements over 1 h of filtration were obtained by using water or gas backpulsing, and 50% enhancement was obtained with crossflushing, for filtration of 1.0 μm diameter carboxylate modified latex (CML) particles using unmodified polypropylene (PP) membranes of 0.3 μm nominal pore diameter. When 0.2 μm diameter CML particles or mixtures of 1.0 and 0.2 μm CML particles were used, however, the average flux decreased 60% compared with using 1.0 μm CML particles for experiments with or without backpulsing.PP membranes were rendered hydrophilic with neutral or positively on negatively charged surfaces by grafting monomers of poly(ethylene glycol 200) monomethacrylate (PEG200MA), dimethyl aminoethyl methacrylate (DMAEMA), or acrylic acid (AA), respectively, to the base PP membranes. Filtration experiments show that fouling is not strongly dependent on membrane surface chemistry for filtration of 1.0 μm CML particles without backpulsing. With backpulsing, however, a 10% increase and a 20% decrease of permeate volumes collected in 1 h were observed when the CML particles and the membranes had like charges and opposite charges, respectively, compared to the permeate collected with the unmodified membrane. Using the PP membranes modified with AA, permeate volumes with backpulsing decreased 30 and 40% when NaCl concentrations of 0.01 and 0.1 M, respectively, were added to the feed. However, the permeate volumes did not vary significantly with changing ionic strength for filtration without backpulsing.     

Membrane-less and mediator-free enzymatic biofuel cell using carbon nanotube/porous silicon electrodes

Membrane-less and mediator-free direct electron transfer enzymatic biofuel cells (BFCs) with bioelectrodes comprised of single wall carbon nanotubes (SWNTs) deposited by two methods on porous silicon (pSi) substrates, are reported. In one method the SWNTs were grown by chemical vapor deposition (CVD) and then functionalized with carboxylic groups, and in the second method, pre-synthesized carboxylated SWNTs (c-SWNTs) were electrophoretically deposited on gold-coated pSi. Anodic glucose oxidase (GOx) and cathodic laccase (Lac) were immobilized on the pSi/SWNT substrates to form BFCs in pH 7 phosphate buffer solution. A peak power density of 1.38 μW/cm² (with a lifetime of 24 h) down to 0.3 μW/cm² was obtained for a BFC comprised of c-SWNT/enzyme electrodes in 4 mM glucose solution as fuel, corresponding to normal blood sugar concentration, and air as oxidant. BFCs of this relatively simple architecture have the potential for further optimization of power output and lifetime.     

Surface structures and electrochemical characteristics of surface-modified carbon anodes for lithium ion battery

Petroleum coke and those heat-treated at 1860 °C, 2100 °C, 2300 °C 2600 °C and 2800 °C (abbreviated as PC, PC1860, PC2100, PC2300, PC2600 and PC2800) were fluorinated by elemental fluorine of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Natural graphite powder samples with average particle sizes of 5 μm, 10 μm and 15 μm (abbreviated as NG5μm, NG10μm and NG15μm) were also fluorinated by ClF₃ of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Transmission electron microscopic (TEM) observation revealed that closed edge of PC2800 was destroyed and opened by surface fluorination, which increased the first coulombic efficiencies of PC2300, PC2600 and PC2800 by 12.1–18.2% at 60 mA/g and by 13.3–25.8% at 150 mA/g in 1 mol/dm³ LiClO₄–ethylene carbonate (EC)/diethyl carbonate (DEC) (1:1 in volume). Light fluorination of NG10μm and NG15μm increased the first coulombic efficiencies by 22.1–28.4% at 150 mA/g in 1 mol/dm³ LiClO₄–EC/DEC/PC (PC: propylene carbonate, 1:1:1 in volume).     

Ion-pairing and reversed phase liquid chromatography for the determination of three different quinolones: Enrofloxacin,lomefloxacin and ofloxacin

Two simple and sensitive high performance liquid chromatographic (HPLC) methods have been developed for the simultaneous determination of three different quinolones: enrofloxacin, lomefloxacin and ofloxacin in their pure and dosage forms, one with reversed phase HPLC and the other with ion-pair HPLC. In reversed phase HPLC, method (A), the mobile phase consists of 2.18% aqueous solution of KH₂PO₄ with pH adjusted to 2.4 ± 0.2 with acetonitrile (80:20; v/v), the mobile phase pumped at flow rate of 1.2 ml min^?1. A Neucleosil C₁₈ column (10 μm, 100 Å), 250 mm length × 4.6 mm diameter was utilized as stationary phase. Detection was affected spectrophotometrically at 294 nm. While in ion-pair HPLC, method (B), the mobile phase was aqueous solution of 0.65% sodium perchlorate and 0.31% ammonium acetate adjusted to pH 2.2 ± 0.2 with orthophosphoric acid: acetonitrile (81:19; v/v), the mobile phase pumped at flow rate of 1.5 ml min^?1. A μ bondapack C₁₈ column (10 μm, 100 Å), 250 mm length × 4.6 mm diameter was utilized as stationary phase. Detection was affected spectrophotometrically at 294 nm. Linearity ranges for enrofloxacin, lomefloxacin and ofloxacin were 4.0–108, 7.0–112 and 8.0–113 μg ml^?1, respectively using method A and 8.0–112, 7.0–112 and 5.0–105 μg ml^?1, respectively applying method B. Minimum detection limits obtained were 0.013, 0.023 and 0.035 μg ml^?1 for enrofloxacin, lomefloxacin and ofloxacin, respectively using method A, and 0.028, 0.023 and 0.011 μg ml^?1 using method B. The proposed methods were further applied to the analysis of enrofloxacin in injection and tablets containing the ofloxacin and lomefloxacin drugs, and the results were satisfied.     

Electrochemical sensing of hydroxylamine by gold nanoparticles on single-walled carbon nanotube films

The arrays of gold nanoparticles (AuNPs) were fabricated on flexible and transparent single-walled carbon nanotube (SWCNT) films using the electrochemical deposition method, and the patterned nanotubes were then used as electrodes for hydroxylamine detection. The sizes and densities of the AuNPs could easily be controlled by varying the amount of charge deposited, and the gold-deposited area showed a homogeneous distribution on the exposed SWCNT film surface. X-ray diffraction analysis of the AuNPs shows a face-centered cubic structure that is dominated by the lowest energy {111} facets. The oxidation of the hydroxylamine on the AuNP-deposited SWCNT films depended strongly on the solution pH, and the maximum catalytic current was observed at a pH of 9.0. A linear electrical response was observed for concentrations ranging from 0.016 to 0.210 mM, and the detection limit and the sensitivity were 0.72 μM and 165.90 μAmM^?1 cm^?2, respectively. Moreover, the amperometric response in hydroxylamine showed a stable response for a long time (300 s), during which time it retained 94% of its initial value. In the long-term storage stability test, the current response to hydroxylamine decreased slightly, with only 17% leakage after 30 days.     

Flame atomic absorption spectrometry determination of trace amount of gold after separation and preconcentration onto ion-exchange polyethylenimine coated on Al2O3

The object of this work is to develop a simple and selective method for efficient extraction of Au(III) ions in aqueous solution using a new solid-phase extraction sorbent. Polyethylenimine (PEI) ion-exchange polymer was coated on alumina in the presence of NaNO₃. The method is based on sorption of Au³⁺ ions on 50 mg PEI/Al₂O₃. A solution of 0.5 M thiourea, then 1.0 M HCl effectively eluted the gold ion and then aspirated into flame atomic absorption spectroscopy (FAAS). The influence of flow rate of sample solution and eluent, the pH effect, eluent type and sorption capacity was investigated. The effects of various diverse ions for preconcentration and separation of the gold ion were investigated. Relative standard deviation of 4.0 μg mL⁻¹ of gold was 1.46% (n = 10). The detection limit was 26.2 ng L⁻¹ in original solution. The method has been applied successfully for the recovery of trace amount of Au(III) ions from water samples.     

Electrochemical stripping analysis of cadmium on tantalum electrode

A tantalum electrode is reported as an alternative electrode for electrochemical stripping analysis for the first time. Several key operational parameters that influenced the electroanalytical signals were optimized, such as pH of the electrolyte, deposition potential and deposition time. The tantalum electrode yields well-defined and sharp stripping signals for trace cadmium analysis when combined with differential pulse anodic stripping voltammetry. Under the optimized condition the electrode shows good linear behavior in the examined concentration in the range of 20–200 μg L^?1 for cadmium, with a detection limit (3σ) of 0.57 μg L^?1 followed a 5-min deposition step under ? 1.3 V. It also shows good reproducibility with a relative standard deviation of 2.56% for ten consecutive measurements. The sensor was also employed for real sample determination and exhibited excellent performance compared with the result of inductively coupled plasma-mass spectrometry.