Photocatalytic degradation of metoprolol in water suspension of TiO<Subscript>2</Subscript> nanopowders prepared using sol–gel route

Nanocrystalline titanium dioxide (TiO₂) powders have been synthesized by sol–gel method using titanium tetrachloride (TiCl₄) or tetrabutyl titanate (Ti(OC₄H₉)₄ as precursors, different alcohols and calcination temperatures in the range from 400 to 650 °C. The photocatalytic activity of as-prepared powders has been tested for the degradation of metoprolol tartrate salt, a selective β-blocker used to treat a variety of cardiovascular diseases, and compared to photocatalytic activity obtained from Degussa P25. Nanosized TiO₂ powders prepared from TiCl₄ and amyl-alcohol, calcined at 550 °C, displayed an activity comparable to Degussa P25, whereas the sample from the same series, calcined at 650 °C, showed higher photocatalytic activity in the whole range of the catalyst loading. Structural, morphological and surface properties of synthesized TiO₂ nanopowders have been investigated by XRD, SEM, EDS and BET measurements, as well as FTIR and Raman spectroscopy, in order to find out the material properties which enable rapid an efficient decomposition of metoprolol under UV radiation.     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Microwave‐Hydrothermal Preparation and Visible‐Light Photoactivity of Plasmonic Photocatalyst Ag‐TiO2 Nanocomposite Hollow Spheres

Visible‐light‐driven plasmonic photocatalyst Ag‐TiO₂ nanocomposite hollow spheres are prepared by a template‐free chemically‐induced self‐transformation strategy under microwave‐hydrothermal conditions, followed by a photochemical reduction process under xenon lamp irradiation. The prepared samples are characterized by using scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, N₂ adsorption‐desorption isotherms, X‐ray photoelectron spectroscopy, UV/Vis and Raman spectroscopy. Production of ?OH radicals on the surface of visible‐light illuminated TiO₂ was detected by using a photoluminescence method with terephthalic acid as the probe molecule. The photocatalytic activity of as‐prepared samples was evaluated by photocatalytic decolorization of Rhodamine B (RhB) aqueous solution at ambient temperature under visible‐light irradiation. The results show that the surface plasmon absorption band of the silver nanoparticles supported on the TiO₂ hollow spheres was red shifted, and a strong surface enhanced Raman scattering effect for the Ag‐TiO₂ nanocomposite sample was observed. The prepared nanocomposite hollow spheres exhibits a highly visible‐light photocatalytic activity for photocatalytic degradation of RhB in water, and their photocatalytic activity is higher than that of pure TiO₂ and commercial Degussa P25 (P25) powders. Especially, the as‐prepared Ag‐TiO₂ nanocomposite hollow spheres at the nominal atomic ratio of silver to titanium ( R ) of 2 showed the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2.     

Photocatalytic Activity of TiO2 Nanofibers with Doped La Prepared by Electrospinning Method

La‐TiO₂ nanofibers are prepared by a sol‐gel assisted electrospinning method. The structure and morphology of La‐TiO₂ nanofibers are characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). XRD analysis shows that the weight percentage of anatase and rutile in the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C is about 8:2, which is similar to P‐25. The XRD data of La‐TiO₂ nanofibers with different La content shows that La³⁺ dopant has a great inhibition on TiO₂ phase transformation. The photocatalytic activity of the as‐prepared La‐TiO₂ nanofibers is evaluated by photocatalytic decolorization of Methylene Blue (MB) aqueous solution. The results show that the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C exhibit high photocatalytic activity, indicating that 600 °C and 1.5 mol% are the appropriate calcination temperature and optimal molar ratio of La to Ti, respectively.     

Effects of gamma-irradiation on physicochemical state of surface and catalytic properties of CuO/MgO and NiO/MgO systems

Copper and nickel oxide samples supported on MgO were prepared by wet impregnation method. The obtained solids were heated at 350 °C and 450 °C. The extent of copper and nickel oxides was fixed at 16.7 mol%. The effect of g-irradiation (0.2-1.6 MGy) on the surface and catalytic properties of the solids were investigated. The techniques employed were XRD, nitrogen adsorption at -196 °C and H₂O₂ decomposition. The results revealed that the g-irradiation up to 0.8 MGy of CuO/MgO-450 °C effected a measurable decrease in the crystallite size of CuO phase with subsequent increase in its degree of ordering. Irradiation at a dose of 1.6 MGy brought about a complete conversion of MgO into Mg(OH)₂ during its cooling from 450 °C to room temperature via interacting with atmospheric water vapor. The S _BET and total pore volume of CuO/MgO precalcined at 350 °C and 450 °C increased progressively as a function of g-ray dose reached a maximum limit at 0.8 MGy. Gamma-irradiation of NiO/MgO-450 °C solids up to 0.8 MGy increased the degree of ordering of MgO and NiO phases without changing their crystallite size. The exposure of these solids to 1.6 MGy led to an effective transformation of some of NiO (not dissolved in MgO lattice) into Ni(OH)₂ via interacting with atmospheric water vapor during cooling from 450 °C to room temperature. Gamma-irradiation led to a measurable increase in the S _BET and V _p of NiO/MgO system. Gamma-irradiation of the two investigated systems resulted in both increase and decrease in their catalytic activities in H₂O₂ decomposition depending mainly on the irradiation dose and calcination temperature. This treatment, however, did not modify the mechanism of the catalytic reaction, but changed the catalytic active sites without changing their energetic nature. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis of TiO2 (B) and High‐temperature Stable Anatase TiO2 Nanowires by Hydrothermal Method and Investigation of Photocatalytic Activity

In this study, TiO₂ nanowires (TNWs) were synthesized through hydrothermal method and were characterized using X‐Ray diffraction (XRD), transmission electron microscopy (TEM) and BET techniques. Monoclinic TiO₂ (B) is the dominant phase of TNWs up to 600°C which is completely transformed into a highly crystalline anatase phase at 800°C. The photocatalytic activity of TNWs, prepared at various calcination temperatures, was investigated in the removal of Rhodamine B as an organic model pollutant. The results indicated that the photocatalytic activity of TNWs, prepared at 800°C calcination temperature, was better than that of other samples and even TiO₂–P25 nanoparticles.     

Effects of Calcination on the Physical and Photocatalytic Properties of TiO<Subscript>2</Subscript> Powders Prepared by Sol–Gel Template Method

TiO₂ powders were prepared by sol–gel template method and calcined under different conditions. XRD, BET and TEM were used to characterize the TiO₂ powders obtained. The photocatalytic activity of TiO₂ was investigated by the degradation of methyl orange. It was found that TiO₂ powder has the highest photocatalytic activity at a calcination temperature of 673 K. The effects of physical properties such as surface area, crystallinity and crystal phase on the photocatalytic activity of TiO₂ were discussed.     

Fullerol–Titania Charge‐Transfer‐Mediated Photocatalysis Working under Visible Light

The development of visible‐light‐active photocatalysts is being investigated through various approaches. In this study, C₆₀‐based sensitized photocatalysis that works through the charge transfer (CT) mechanism is proposed and tested as a new approach. By employing the water‐soluble fullerol (C₆₀(OH)_x) instead of C₆₀, we demonstrate that the adsorbed fullerol activates TiO₂ under visible‐light irradiation through the “surface–complex CT” mechanism, which is largely absent in the C₆₀/TiO₂ system. Although fullerene and its derivatives have often been utilized in TiO₂‐based photochemical conversion systems as an electron transfer relay, their successful photocatalytic application as a visible‐light sensitizer of TiO₂ is not well established. Fullerol/TiO₂ exhibits marked visible photocatalytic activity not only for the redox conversion of 4‐chlorophenol, I^?, and Cr^VI, but also for H₂ production. The photoelectrode of fullerol/TiO₂ also generates an enhanced anodic photocurrent under visible light as compared with the electrodes of bare TiO₂ and C₆₀/TiO₂, which confirms that the visible‐light‐induced electron transfer from fullerol to TiO₂ is particularly enhanced. The surface complexation of fullerol/TiO₂ induced a visible absorption band around 400–500 nm, which was extinguished when the adsorption of fullerol was inhibited by fluorination of the surface of TiO₂. The transient absorption spectroscopic measurement gave an absorption spectrum ascribed to fullerol radical cations (fullerol^.+) the generation of which should be accompanied by the proposed CT. The theoretical calculation regarding the absorption spectra for the (TiO₂ cluster+fullerol) model also confirmed the proposed CT, which involves excitation from HOMO (fullerol) to LUMO (TiO₂ cluster) as the origin of the visible‐light absorption.     

Large‐Scale Production of Hierarchical TiO2 Nanorod Spheres for Photocatalytic Elimination of Contaminants and Killing Bacteria

We report a facile non‐hydrothermal method for the large‐scale production of hierarchical TiO₂ nanorod spheres for the photocatalytic elimination of contaminants and killing bacteria. Crescent Ti/RF spheres were prepared by deliberately adding titanium trichloride (TiCl₃) to the reaction of resorcinol (R) and formaldehyde (F) in an open reactor under heating and stirring. The hierarchical TiO₂ nanorod spheres were obtained by calcining the crescent Ti/RF spheres in a furnace in air to burn off the RF spheres. This method has many merits, such as large‐scale production, good crystallisation of TiO₂, and good reproducibility, all of which are difficult to realise by conventional hydrothermal methods. The calcination temperature plays a significant role in influencing the morphology, crystallisation, porosity, Brunauer–Emmett–Teller (BET) specific surface area, and hierarchy of the TiO₂ nanorod spheres, thus resulting in different photocatalytic performances under UV light and solar light irradiation. The experimental results have demonstrated that the hierarchical TiO₂ nanorod spheres obtained after calcination of the crescent Ti/RF spheres at different temperatures displayed similar photocatalytic activities under irradiation with UV light. We attribute this to a balance of opposing effects of the investigated factors. A higher calcination temperature leads to greater light absorption capability of the TiO₂ nanorod spheres, thus resulting in higher photocatalytic antibacterial activity under solar light irradiation. It is also interesting to note that the hierarchical TiO₂ nanorod spheres displayed intrinsic antibacterial activity in the absence of light irradiation, apparently because their sharp outward spikes can easily pierce and penetrate the walls of bacteria. In this study, the sharpest hierarchical TiO₂ nanorod spheres were obtained after calcination at 500 °C, and these exhibited the highest antibacterial activity without light irradiation. A higher calcination temperature proved detrimental to the sharpness of the TiO₂ nanorods, thus reducing their intrinsic antibacterial activity.     

Physical properties of nano-titania hollow fibers and their photocatalytic activity in the decomposition of phenol

A series of nano-titania (TiO₂) photocatalytic materials with a hollow fiber structure were successfully prepared using tetra-n-butyl titanate (Ti(OC₄H₉)₄) as precursor and cotton fiber as the template. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and N₂ adsorption-desorption measurements were employed to characterize the morphology, crystal structure, and surface structure of the samples. The photocatalytic activities of the samples were studied by phenol photodegradation in water under UV irradiation. The effect of calcination temperature, photocatalyst dosage, initial concentration of phenol and irradiation time on the photodegradation of phenol was studied. Results showed that the TiO₂ fiber materials have hollow structures, indicating that these materials had a large specific surface area. The fiber structure material showed better photocatalytic properties for the degradation of phenol than pure TiO₂ under UV light, and the sample calcined at 500°C exhibited the highest phenol photodegradation efficiency. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed, the photocatalytic activity of TiO₂ fiber remained ca. 90% of photocatalytic activity of the fresh sample after being used four times. Moreover, TiO₂ fiber was easily recovered by centrifugal separation from water.     

Effect of atomic-layer-deposited TiO2 on carbon-supported Ni catalysts for electrocatalytic glycerol oxidation in alkaline media

Thin TiO₂ layers were deposited onto a carbon-supported Ni catalyst (Ni/C) through atomic layer deposition (ALD) and the resulting TiO₂-coated Ni/C (ALD(TiO₂)-Ni/C) was utilized for electrochemical glycerol oxidation in alkaline media. X-ray photoelectron spectroscopy analysis demonstrated that the Ni surface phase of ALD(TiO₂)-Ni/C mainly consisted of Ni(OH)₂ while that of uncoated Ni/C was a mixed phase of NiO and Ni(OH)₂. The ALD(TiO₂)-Ni/C exhibited electrocatalytic activity at least 2.4 times higher than that of Ni/C. Density functional theory calculations were used to investigate how the modified Ni surface with the TiO₂ coating affects the adsorption/desorption of glycerol.     

Molten‐Salt‐Mediated Synthesis of an Atomic Nickel Co‐catalyst on TiO2 for Improved Photocatalytic H2 Evolution

Atomic co‐catalysts offer high potential to improve the photocatalytic performance, of which the preparation with earth‐abundant elements is challenging. Here, a new molten salt method (MSM) is designed to prepare atomic Ni co‐catalyst on widely studied TiO₂ nanoparticles. The liquid environment and space confinement effect of the molten salt leads to atomic dispersion of Ni ions on TiO₂, while the strong polarizing force provided by the molten salt promotes formation of strong Ni?O bonds. Interestingly, Ni atoms are found to facilitate the formation of oxygen vacancies (OV) on TiO₂ during the MSM process, which benefits the charge transfer and hydrogen evolution reaction. The synergy of atomic Ni co‐catalyst and OV results in 4‐time increase in H₂ evolution rate compared to that of the Ni co‐catalyst on TiO₂ prepared by an impregnation method. This work provides a new strategy of controlling atomic co‐catalyst together with defects for efficient photocatalytic water splitting.     

The improved photocatalytic properties of P-type NiO loaded porous TiO2 sheets prepared via freeze tape-casting

For the interest of the practical application, porous TiO₂ sheets were prepared by a novel freeze tape-casting method, in order to improve the photocatalytic activities of these TiO₂ sheets, p-type NiO was loaded by chemical solution deposition. The samples were characterized by a series of physical means, including XRD, SEM, EDS, XPS, ICP-OES, and UV-vis spectroscopy. The photocatalytic activities of the samples were evaluated by the degradation of methyl orange solution. The results showed that the photocatalytic activity of the TiO₂ sheet was greatly enhanced by the NiO loading, and the photocatalytic efficiency increased with increasing the NiO loading, the extraordinary performance for the NiO-loaded sample with 0.1 M precursor dipped was related to its unique morphology. The sample annealed at 600 °C showed the better photocatalytic activity than the sample annealed at 400 °C and 800 °C. The improvement of the photocatalytic activity was attributed to the formation of p–n junctures at the interface of the NiO/TiO₂, which facilitates the photoinduced electron/hole pairs' separation by the inner electric field, thus leading to the higher photocatalytic activities for the NiO-loaded TiO₂ sheets.     

A comparative study on characterization and photocatalytic activities of gadolinium–boron codoped and mono-doped TiO2 nanoparticles

Gadolinium?Cboron codoped and mono-doped TiO₂ nanoparticles were prepared using a sol?Cgel method, and tested for photocatalytic activity by the UV light after a further calcination process. For comparison, a pure TiO₂ sample was also prepared and tested under the same conditions. The prepared catalysts were characterized by X-ray diffraction, scanning electron microscope, and UV?CVis spectra. The photocatalytic activity of the samples was evaluated through the photo-degradation of three different dyes under UV light. The experiments demonstrated that the gadolinium?Cboron codoped TiO₂ (Gd?CB?CTiO₂) sample calcined at 500?°C possessed the best photocatalytic activity, and the photodegradation rate of the Reactive Brilliant Red K2G aqueous solution could reach to 95.7% under UV irradiation for 80?min. The results showed that Gd?CB?CTiO₂ has smaller crystallite size and higher photocatalytic activity than that of mono-doped TiO₂ samples and undoped TiO₂.     

Graphene Nanosheets as a Platform for the 2D Ordering of Metal Oxide Nanoparticles: Mesoporous 2D Aggregate of Anatase TiO2 Nanoparticles with Improved Electrode Performance

Graphene nanosheets are successfully applied as an effective platform for the 2D ordering of metal oxide nanoparticles. Mesoporous 2D aggregates of anatase TiO₂ nanoparticles are synthesized by the heat treatment of the uniformly hybridized nanocomposite of layered titanate–reduced graphene oxide (RGO) at elevated temperatures. The precursor layered titanate–RGO nanocomposite is prepared by self‐assembly of anionic RGO nanosheets and cationic TiO₂ nanosols. The calcination of the as‐prepared layered titanate–RGO nanocomposite at 500 °C induces a structural and morphological change of layered titanate nanoplates into anatase TiO₂ nanoparticles without significant modification of the RGO nanosheet. Increasing the heating temperature to 600 °C gives rise to elimination of the RGO component, leading to the formation of sheetlike porous aggregates of RGO‐free TiO₂ nanoparticles. The nanocomposites calcined at 500–700 °C display promising functionality as negative electrodes for lithium ion batteries. Among the present calcined derivatives, the 2D sheet‐shaped aggregate of TiO₂ nanoparticles obtained from calcination at 600 °C delivers the greatest specific discharge capacity with good capacity retention for all current density conditions applied. Such superior electrode performance of the nanocomposite calcined at 600 °C is attributable both to the improved stability of the crystal structure and crystal morphology of titania and to the enhancement of Li⁺ ion transport through the enlargement of mesopores. The present findings clearly demonstrate the usefulness of RGO nanosheets as a platform for 2D‐ordered superstructures of metal oxide nanoparticles with improved electrode performance.     

Preparation of TiO2 nanocrystallites by hydrolyzing with gaseous water and their photocatalytic activity

TiO₂ nanocrystallites were prepared from precursors tetra-n-butyl titanate (Ti(OC₄H₉)₄) and titanium tetrachloride (TiCl₄). The precursors were hydrolyzed by gaseous water in autoclave, and then calcined at predetermined testing temperatures. The samples were characterized by X-ray diffraction (XRD), thermogravimetry–differential thermal analysis (TG–DTA), field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectra (FT-IR), and UV–vis diffuse reflectance spectra (DRS). The photocatalytic activities of the samples were evaluated by the photobleaching of methylene blue (MB) in aqueous solution and the photocatalytic oxidation of propylene in gas phase at ambient temperature. The results showed that the anatase phase nanocrystalline TiO₂ could be obtained at relatively low temperatures (for precursor Ti(OC₄H₉)₄ at 110 °C and for TiCl₄ at 140 °C, respectively), and that the as prepared samples exhibited high photocatalytic activities to photobleach MB in aqueous solution. As the calcination temperatures increasing, the decolor ratio of MB increased and reached the maximum value of nearly 100% at 600 °C, and then decreased. The photobleaching of MB by all samples followed the pseudo-first-order kinetics with respect to MB concentration. The photodecomposition amount of propylene by TiO₂ nanocrystallites calcined at 600 °C from precursor of Ti(OC₄H₉)₄ is 21.6%, which is approaching to that by Degussa P25 TiO₂ (24.9%).     

Effect of calcination temperature on the photocatalytic activity of carbon‐doped titanium dioxide revealed by photoluminescence study

Carbon‐doped titania (C‐TiO₂) nanoparticles were synthesized by the sol–gel method at different calcination temperatures (300–600°C) employing titanium tetraisopropoxide (TTIP) as the titanium source and polyoxyethylene sorbitan monooleate (Tween 80) as the carbon source. The physical properties of C‐TiO₂ samples were characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). The photocatalytic activities were checked through the photodegradation of phenolphthalein (PHP) under ultraviolet irradiation. The UV spectrum showed that the carbon doping extends the absorption range of TiO₂ to the visible region. However, the photocatalytic activity is affected by the electron–hole recombination phenomenon, as revealed by the photoluminescence (PL) study. According to the PL spectra, carbon doping reduces the edge‐to‐edge electron–hole recombination. Nevertheless, the number of defect sites is greatly influenced by the calcination temperature of C‐TiO₂. C‐TiO₂ that was calcined at 400°C showed the highest photodegradation percentage of PHP, which was mainly attributed to the synergic effect of the low direct edge‐to‐edge electron–hole recombination, high content of defect sites, and retention of active electrons on the surface hydroxyl group.     

Mechanochemical synthesis of nanocrystalline nickel-molybdenum compounds,their morphology and application in catalysis: I. Effect of the Ni: Mo atomic ratio on the structure and properties of nickel-molybdenum compounds prepared under mechanochemical synthesis conditions

Mechanochemical activation in high-energy planetary activators was used for the preparation of highly dispersed nickel-molybdenum compounds. Nickel hydroxocarbonate [NiCO₃ · 2Ni(OH)₂ · nH₂O] and ammonium paramolybdate [(NH₄)₆Mo₇O₂₄ · 4H₂O] were chosen as starting compounds. The effect of the Ni: Mo atomic ratio on the composition and structure of products formed in the process of mechanochemical activation followed by calcination was studied. It was found that, at the Ni: Mo atomic ratios of 1.0 and 1.4, the mechanically activated product after calcination at 520°C contained 70–100% β-NiMoO₄, which is a stable phase at temperatures lower than 180°C.     

Methyl 4‐O‐β‐D‐mannopyranosyl β‐D‐xylopyranoside

Methyl β‐D‐mannopyranosyl‐(1→4)‐β‐D‐xylopyranoside, C₁₂H₂₂O₁₀, (I), crystallizes as colorless needles from water, with two crystallographically independent molecules, (IA) and (IB), comprising the asymmetric unit. The internal glycosidic linkage conformation in molecule (IA) is characterized by a ϕ′ torsion angle (O5′_Man—C1′_Man—O1′_Man—C4_Xyl; Man is mannose and Xyl is xylose) of −88.38 (17)° and a ψ′ torsion angle (C1′_Man—O1′_Man—C4_Xyl—C5_Xyl) of −149.22 (15)°, whereas the corresponding torsion angles in molecule (IB) are −89.82 (17) and −159.98 (14)°, respectively. Ring atom numbering conforms to the convention in which C1 denotes the anomeric C atom, and C5 and C6 denote the hydroxymethyl (–CH₂OH) C atom in the β‐Xylp and β‐Manp residues, respectively. By comparison, the internal glycosidic linkage in the major disorder component of the structurally related disaccharide, methyl β‐D‐galactopyranosyl‐(1→4)‐β‐D‐xylopyranoside), (II) [Zhang, Oliver & Serriani (2012). Acta Cryst. C 68 , o7–o11], is characterized by ϕ′ = −85.7 (6)° and ψ′ = −141.6 (8)°. Inter‐residue hydrogen bonding is observed between atoms O3_Xyl and O5′_Man in both (IA) and (IB) [O3_Xyl...O5′_Man internuclear distances = 2.7268 (16) and 2.6920 (17) Å, respectively], analogous to the inter‐residue hydrogen bond detected between atoms O3_Xyl and O5′_Gal in (II). Exocyclic hydroxymethyl group conformation in the β‐Manp residue of (IA) is gauche–gauche, whereas that in the β‐Manp residue of (IB) is gauche–trans.     

流化床中高分散镍基催化剂上甲烷的自热重整和部分氧化

Highly dispersed Ni catalysts on spherical SiO2 were prepared by simple impregnation of Ni（acac）2, [Ni-（NH3）6-n（H2O）n]^2＋, [Ni（en）3]^2＋ and [Ni（EDTA）]^2-. Pulse adsorption of H2 and TEM analysis results confirmed that Ni was dispersed very well on the surface of SiO2 even after calcination （4 h） and reduction （1 h） at high temperature of 800 ℃. These highly dispersed and uniquely sized Ni crystallites were more stable and more reactive for both autothermal reforming and partial oxidation of methane in fluidized reactor.