Nanostructured organic–inorganic hybrid films prepared by the sol–gel method from self‐assemblies of PS‐b‐paptes‐b‐PS triblock copolymers

ABA‐based triblock copolymers of styrene as block ends and gelable 3‐acryloxypropyltriethoxysilane (APTES) as the middle block were successfully prepared through nitroxide‐mediated polymerization (NMP). The copolymers were bulk self‐assembled into films and the degree of phase separation between the two blocks was evaluated by differential scanning calorimetry (DSC). Their morphology was examined through small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM), whereas the mechanical properties of the corresponding cross‐linked self‐assembled nanostructures were characterized by dynamic mechanical analysis (DMA). Acidic treatment of the triblock copolymers favored the hydrolysis and condensation reactions of the APTES‐rich nanophase, and induced a mechanical reinforcement evidenced by the increase of storage modulus values and the shift of the glass transition temperature to higher temperatures due to confinement effects. In addition, the lamellar structure of the hybrid films was retained after the removal of the organic part by calcination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Recent advances in the solution self‐assembly of amphiphilic “rod‐coil” copolymers

Solution self‐assembly of amphiphilic “rod‐coil” copolymers, especially linear block copolymers and graft copolymers (also referred to as polymer brushes), has attracted considerable interest, as replacing one of the blocks of a coil‐coil copolymer with a rigid segment results in distinct self‐assembly features compared with those of the coil‐coil copolymer. The unique interplay between microphase separation of the rod and coil blocks with great geometric disparities can lead to the formation of unusual morphologies that are distinctly different from those known for coil‐coil copolymers. This review presents the recent achievements in the controlled self‐assembly of rod‐coil linear block copolymers and graft copolymers in solution, focusing on copolymer systems containing conjugated polymers, liquid crystalline polymers, polypeptides, and polyisocyanates as the rod segments. The discussions concentrate on the principle of controlling over the morphology of rod‐coil copolymer assemblies, as well as their distinctive optical and optoelectronic properties or biocompatibility and stimuli‐responsiveness, which afford the assemblies great potential as functional materials particularly for optical, optoelectronic and biological applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1459–1477     

Nanostructured hybrid polymer networks from in situ self‐assembly of RAFT‐synthesized POSS‐based block copolymers

A series of well‐defined hybrid block copolymers PMACyPOSS‐b‐PMMA and PMAiBuPOSS‐b‐PMMA exhibiting high POSS weight contents have been synthesized by RAFT polymerization and further studied as modifiers for epoxy thermosets based on diglycidyl ether of bisphenol A. The hybrid block copolymers self‐assembled within the epoxy precursors into micelles possessing an inorganic core and a PMMA corona. Thanks to the presence of the PMMA blocks that remain miscible until the end of the reaction, curing of the resulting blends afforded nanostructured hybrid organic/inorganic networks with well‐dispersed inorganic‐rich nanodomains with diameters on the order of 20 nm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Optoelectronic Properties of Dicyanofluorene‐Based n‐Type Polymers

Three new donor–acceptor‐type copolymers ( P1 , P2 , P3 ) consisting of dicyanofluorene as acceptor and various donor moieties were designed and synthesized. Optoelectronic properties were studied in detail by means of UV‐visible absorption and fluorescence spectroscopy, cyclic voltammetry, space‐charge‐limited current (SCLC), flash‐photolysis time‐resolved microwave conductivity (FP‐TRMC), and density functional theory (DFT). All polymers showed strong absorption in the UV‐visible region and the absorption maximum undergoes redshift with an increasing number of thiophene units in the polymer backbone. SCLC analysis showed that the electron mobilities of the polymers in the bulk state were 1 to 2 orders higher than that of the corresponding hole mobilities, which indicated the n‐type nature of the materials. By using FP‐TRMC, the intrapolymer charge‐carrier mobility was assessed and compared with the interpolymer mobility obtained by SCLC. The polymers exhibited good electron‐accepting properties sufficiently high enough to oxidize the excited states of regioregular poly(3‐hexylthiophene) (P3HT (donor)), as evident from the FP‐TRMC analysis. The P3 polymer exhibited the highest FP‐TRMC transients in the pristine form as well as when blended with P3HT. Use of these polymers as n‐type materials in all‐polymer organic solar cells was also explored in combination with P3HT. In accordance with the TRMC results, P3 exhibited superior electron‐transport and photovoltaic properties to the other two polymers, which is explained by the distribution of the energy levels of the polymers by using DFT calculations.     

Exploring the synthesis and impact of end‐functional poly(3‐hexylthiophene)

In recent years, end‐functional poly(3‐hexylthiophene) (P3HT) has proven to be instrumental in the continued development and innovation within the broad conjugated polymer arena, enabling a variety of applications, particularly in organic electronics. The availability of P3HT with controlled molecular weights, low polydispersity, and importantly, a wide range of reactive end‐groups not only serves as a key building block for the preparation of conjugated block copolymers but also facilitates the development of hybrid nanocomposite materials via inorganic surface modification strategies. This Highlight focuses on the synthetic approaches to end‐functional P3HT and the impact of these systems in emerging technologies. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 831–841     

Incorporation of metal‐organic framework amino‐modified MIL‐101 into glycidyl methacrylate monoliths for nano LC separation

Metal‐organic frameworks consisting of amino‐modified MIL‐101(M: Cr, Al, and Fe) crystals have been synthesized and subsequently incorporated to glycidyl methacrylate monoliths to develop novel stationary phases for nano‐liquid chromatography. Two incorporation approaches of these materials in monoliths were explored. The metal‐organic framework materials were firstly attached to the pore surface through reaction of epoxy groups present in the parent glycidyl methacrylate‐based monolith. Alternatively, NH₂‐MIL‐101(M) were admixed in the polymerization mixture. Using short time UV‐initiated polymerization, monolithic beds with homogenously dispersed metal‐organic frameworks were obtained. The chromatographic performance of embedded UV‐initiated composites was demonstrated with separations of polycyclic aromatic hydrocarbons and non‐steroidal anti‐inflammatory drugs as test solutes. In particular, the incorporation of the NH₂‐MIL‐101(Al) into the organic polymer monoliths led to an increase in the retention of all the analytes compared to the parent monolith. The hybrid monolithic columns also exhibited satisfactory run‐to‐run and column‐to‐column reproducibility.     

Chitosan Bio‐Based Organic–Inorganic Hybrid Aerogel Microspheres

Recently, organic–inorganic hybrid materials have attracted tremendous attention thanks to their outstanding properties, their efficiency, versatility and their promising applications in a broad range of areas at the interface of chemistry and biology. This article deals with a new family of surface‐reactive organic–inorganic hybrid materials built from chitosan microspheres. The gelation of chitosan (a renewable amino carbohydrate obtained by deacetylation of chitin) by pH inversion affords highly dispersed fibrillar networks shaped as self‐standing microspheres. Nanocasting of sol–gel processable monomeric alkoxides inside these natural hydrocolloids and their subsequent CO₂ supercritical drying provide high‐surface‐area organic–inorganic hybrid materials. Examples including chitosan–SiO₂, chitosan–TiO₂, chitosan–redox‐clusters and chitosan–clay‐aerogel microspheres are described and discussed on the basis of their textural and structural properties, thermal and chemical stability and their performance in catalysis and adsorption.     

Incorporation of 2,6‐Connected Azulene Units into the Backbone of Conjugated Polymers: Towards High‐Performance Organic Optoelectronic Materials

Azulene is a promising candidate for constructing optoelectronic materials. An effective strategy is presented to obtain high‐performance conjugated polymers by incorporating 2,6‐connected azulene units into the polymeric backbone, and two conjugated copolymers P(TBAzDI‐TPD) and P(TBAzDI‐TFB) were designed and synthesized based on this strategy. They are the first two examples for 2,6‐connected azulene‐based conjugated polymers and exhibit unipolar n‐type transistor performance with an electron mobility of up to 0.42 cm² V^?1 s^?1, which is among the highest values for n‐type polymeric semiconductors in bottom‐gate top‐contact organic field‐effect transistors. Preliminary all‐polymer solar cell devices with P(TBAzDI‐TPD) as the electron acceptor and PTB7‐Th as the electron donor display a power conversion efficiency of 1.82 %.     

Construction of nanostructures in aqueous solution from amphiphilic glucose‐derived polycarbonates

Carbohydrates are the fundamental building blocks of many natural polymers, their wide bioavailability, high chemical functionality, and stereochemical diversity make them attractive starting materials for the development of new synthetic polymers. In this work, one such carbohydrate, d ‐glucopyranoside, was utilized to produce a hydrophobic five‐membered cyclic carbonate monomer to afford sugar‐based amphiphilic copolymers and block copolymers via organocatalyzed ring‐opening polymerizations with 4‐methylbenzyl alcohol and methoxy poly(ethylene glycol) as initiator and macroinitiator, respectively. To modulate the amphiphilicities of these polymers acidic benzylidene cleavage reactions were performed to deprotect the sugar repeat units and present hydrophilic hydroxyl side chain groups. Assembly of the polymers under aqueous conditions revealed interesting morphological differences, based on the polymer molar mass and repeat unit composition. The initial polymers, prior to the removal of the benzylidenes, underwent a morphological change from micelles to vesicles as the sugar block length was increased, causing a decrease in the hydrophilic–hydrophobic ratio. Deprotection of the sugar block increased the hydrophilicity and gave micellar morphologies. This tunable polymeric platform holds promise for the production of advanced materials for implementation in a diverse range of applications. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 432–440     

Lanthanide (Eu3+, Tb3+) Centered Mesoporous Hybrids with 1,3‐Diphenyl‐1,3‐Propanepione Covalently Linking SBA‐15 (SBA‐16) and Poly(methylacrylic acid)

1,3‐Diphenyl‐1,3‐propanepione (DBM)‐functionalized SBA‐15 and SBA‐16 mesoporous hybrid materials (DBM‐SBA‐15 and DBM‐SBA‐16) are synthesized by co‐condensation of modified 1,3‐diphenyl‐1,3‐propanepione (DBM‐Si) and tetraethoxysilane (TEOS) in the presence of Pluronic P123 and Pluronic F127 as a template, respectively. The as‐synthesized mesoporous hybrid material DBM‐SBA‐15 and DBM‐SBA‐16 are used as the first precursor, and the second precursor poly(methylacrylic acid) (PMAA) is synthesized through the addition polymerization reaction of the monomer methacrylic acid. These precursors then coordinate to lanthanide ions simultaneously, and the final mesoporous polymeric hybrid materials Ln(DBM‐SBA‐15)₃PMAA and Ln(DBM‐SBA‐16)₃PMAA (Ln=Eu, Tb) are obtained by a sol‐gel process. For comparison, binary lanthanide SBA‐15 and SBA‐16 mesoporous hybrid materials (denoted as Ln(DBM‐SBA‐15)₃ and Ln(DBM‐SBA‐16)₃) are also synthesized. The luminescence properties of these resulting materials are characterized in detail, and the results reveal that ternary lanthanide mesoporous polymeric hybrid materials present stronger luminescence intensities, longer lifetimes, and higher luminescence quantum efficiencies than the binary lanthanide mesoporous hybrid materials. This indicates that the introduction of the organic polymer chain is a benefit for the luminescence properties of the overall hybrid system. In addition, the SBA‐15 mesoporous hybrids show an overall increase in luminescence lifetime and quantum efficiency compared with SBA‐16 mesoporous hybrids, indicating that SBA‐15 is a better host material for the lanthanide complex than mesoporous silica SBA‐16.     

An efficient approach to synthesize polysaccharides‐graft‐poly(p‐dioxanone) copolymers as potential drug carriers

Starch and poly(p‐dioxanone) (PPDO) are the natural and synthetic biodegradable and biocompatible polymers, respectively. Their copolymers can find extensive applications in biomedical materials. However, it is very difficult to synthesize starch‐graft‐PPDO copolymers in common organic solvents with very good solubility. In this article, well‐defined polysaccharides‐graft‐poly(p‐dioxanone) (SA_n‐PPDO) copolymers were successfully synthesized via the ring‐opening polymerization of p‐dioxanone (PDO) with an acetylated starch (SA) initiator and a Sn(Oct)₂ catalyst in bulk. The copolymers were characterized via Fourier transform infrared spectroscopy, ¹H NMR, gel permeation chromatography, thermogravimetric analysis (TG), differential scanning calorimetry, and wide angle x‐ray diffraction. The in vitro degradation results showed that the introduction of SA segments into the backbone chains of the copolymers led to an enhancement of the degradation rate, and the degradation rate of SA_n‐PPDO increased with the increase of SA wt %. Microspheres with an average volume diameter of 20 μm, which will have potential applications in controlled release of drugs, were successfully prepared by using these new copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5344–5353, 2009     

In Situ Hetero End‐Functionalized Polythiophene and Subsequent “Click” Chemistry With DNA

It is demonstrated that bifunctionalized polythiophenes involving thiol and azide end‐functional groups can be synthesized by chain‐growth Suzuki‐Miyaura type polymerization. The bifunctionalized polythiophenes are successfully characterized by 1H NMR, gel permeation chromatography (GPC), and matrix‐assisted laser desorption ionization time‐of‐flight (MALDI‐TOF). Furthermore, the azide end‐group reacts with DNA via “click chemistry” to form a polythiophene/DNA hybrid structure, which is characterized by ESI‐MS. The described synthetic approaches will lead to the synthesis of novel multi‐block copolymers as well as biomolecule‐based conjugated polymer structures.     

Synthesis of linear and 4‐arm star block copolymers of poly(methyl acrylate‐b‐solketal acrylate) by SET‐LRP at 25 °C

The new SET‐LRP (using Cu(0) powder for organic synthesis) was successfully used to produce well‐defined linear and star homo‐ and diblock‐copolymers of PMA, PSA, and P(MA‐b‐GA)_n (where n = 1 or 4). The kinetic data showed that all SET‐LRP were first order and reached high conversions in a short period of time. The other advantage of using such a system is that the copper can easily be removed through filtration, allowing the production of highly pure polymer. The molecular weight distributions were well controlled with polydispersity indexes below 1.1 and the number‐average molecular weight close to theory, especially upon the addition of Cu(II)Br₂/Me₆‐TREN complex. The linear and star block copolymers were then hydrolyzed to produce the biocompatible amphiphilic P(MA‐b‐GA)_n, where the glycerol side‐groups make the outer block hydrophilic. These blocks were micellized into water and found to have a R_g/R_H equal to 0.8 and 1.59 for the liner and star blocks, respectively. This together with the TEM's supported that the linear blocks formed the classical core‐shell micelles, where as, the star blocks formed vesicles. We found direct support for the vesicle structure from a TEM where one vesicle squashed a second vesicle consistent with a hollow structure. Such vesicle structures have potential applications as delivery nanoscaled devices for drugs and other important biomolecules. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6346–6357, 2008     

Bis‐dendritic polyethylene prepared by ring‐opening metathesis polymerization in the presence of bis‐dendritic chain transfer agents

The synthesis of ABA triblock copolymers is described, in which the A blocks are poly(benzyl ether) dendrons and the B block is polycyclooctene or polyethylene. Bis‐dendritic cis‐olefins were synthesized and used as chain transfer agents in ring‐opening metathesis polymerization of cyclooctene in a process that inserts the dendrons at the polymer chain‐ends. Evaluation of the polymer products by spectroscopic, chromatographic, and titration methods supports their triblock structure. Hydrogenation of the unsaturated polycyclooctene B‐block of these ABA triblock copolymers provides the first reported synthesis of bisdendritic polyethylene. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5429–5439, 2005     

Self‐assembly of block copolymers with an alkoxysilane‐based core‐forming block: A comparison of synthetic approaches

Polymerization‐induced self‐assembly (PISA) has become the preferred method of preparing self‐assembled nano‐objects based on amphiphilic block copolymers. The PISA methodology has also been extended to the realization of colloidal nanocomposites, such as polymer–silica hybrid particles. In this work, we compare two methods to prepare nanoparticles based on self‐assembly of block copolymers bearing a core‐forming block with a reactive alkoxysilane moiety (3‐(trimethoxysilyl)propyl methacrylate, MPS), namely (i) RAFT emulsion polymerization using a hydrophilic macroRAFT agent and (ii) solution‐phase self‐assembly upon slow addition of a selective solvent. Emulsion polymerization under both ab initio and seeded conditions were studied, as well the use of different initiating systems. Effective and reproducible chain extension (and hence PISA) of MPS via thermally initiated RAFT emulsion polymerization was compromised due to the hydrolysis and polycondensation of MPS occurring under the reaction conditions employed. A more successful approach to block copolymer self‐assembly was achieved via polymerization in a good solvent for both blocks (1,4‐dioxane) followed by the slow addition of water, yielding spherical nanoparticles that increased in size as the length of the solvophobic block was increased. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 420–429     

Supramolecular Diblock Copolymers Featuring Well‐defined Telechelic Building Blocks

We report supramolecular AB diblock copolymers comprised of well‐defined telechelic building blocks. Helical motifs, formed via reversible addition‐fragmentation chain‐transfer (RAFT) or anionic polymerization, are assembled with coil‐forming and sheet‐featuring blocks obtained via atom‐transfer radical polymerization (ATRP) or ring‐opening metathesis polymerization (ROMP). Interpolymer hydrogen bonding or metal‐coordination achieves dynamic diblock architectures featuring hybrid topologies of coils, helices, and/or π‐stacked sheets that, on a basic level, mimic protein structural motifs in fully synthetic systems. The intrinsic properties of each block (e.g., circular dichroism and fluorescence) remain unaffected in the wake of self‐assembly. This strategy to develop complex synthetic polymer scaffolds from functional building blocks is significant in a field striving to produce architectures reminiscent of biosynthesis, yet fully synthetic in nature. This is the first plug‐and‐play approach to fabricate hybrid π‐sheet/helix, π‐sheet/coil, and helix/coil architectures via directional self‐assembly.     

Synthesis and characterization of new light‐emitting copolymers in polymeric‐light‐emitting‐diode device fabrications

A series of thiophene‐containing photoactive copolymers consisting of alternating conjugated and nonconjugated segments were synthesized. The ¹H NMR spectra corroborated the well‐defined structures, and the copolymers not only were soluble in common organic solvents but also had high glass‐transition temperatures (ca. 130 °C) and good thermal stability up to 390 °C. Introducing aliphatic functional groups, such as alkyl or alkoxyl, into chromophores of the copolymers redshifted the photoluminescence spectra and lowered the optical bandgaps. The electrochemical bandgaps calculated from cyclic voltammetry agreed with the optical bandgaps and thus indicated that electroluminescence and photoluminescence originated from the same excited state. The energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) of all the copolymers were lower than those of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1.4‐phenylenevinylene] MEH–PPV, indicating balanced hole and electron injection, which led to improved performance in both single‐layer and double‐layer polymeric‐light‐emitting‐diode devices fabricated with these copolymers. All the copolymers emitted bluish‐green or green light above the threshold bias of 5.0 V under ambient conditions. At the maximum bias of 10 V, the electroluminescence of a device made of poly(2‐{4‐[2‐(3‐ethoxy phenyl)ethylene]phenyl}‐5‐{4‐[2‐(3‐ethoxy,4‐1,8‐octanedioxy phenyl)ethylene]phenyl}thiophene) was 5836 cd/m². The external electroluminescence efficiency decreased with the lifetime as the polymer degraded. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3954–3966, 2004     

Spontaneous Assembly of an Organic–Inorganic Nucleic Acid Z‐DNA Double‐Helix Structure

Herein, we report a hybrid polyoxometalate organic–inorganic compound, Na₂[(HGMP)₂Mo₅O₁₅]⋅7 H₂O ( 1 ; where GMP=guanosine monophosphate), which spontaneously assembles into a structure with dimensions that are strikingly similar to those of the naturally occurring left‐handed Z‐form of DNA. The helical parameters in the crystal structure of the new compound, such as rise per turn and helical twist per dimer, are nearly identical to this DNA conformation, allowing a close comparison of the two structures. Solution circular dichroism studies show that compound 1 also forms extended secondary structures in solution. Gel electrophoresis studies demonstrate the formation of non‐covalent adducts with natural plasmids. Thus we show a route by which simple hybrid inorganic–organic monomers, such as compound 1 , can spontaneously assemble into a double helix without the need for a covalently connected linear sequence of nucleic acid base pairs.     

Synthesis and Characterization of Novel Biodegradable Di‐ and Tri‐Block Copolymers Based on Ethylene Carbonate Polymer as Hydrophobic Segment

Synthesis of novel amphiphilic biodegradable block copolymers based on ethylene carbonate is reported in this study. Polyethylene glycol monomethyl ether (MeO‐PEO) and polyethylene glycol (PEG) of varying molar masses are used as macro‐initiator for ring‐opening polymerization of ethylene carbonate in the presence of sodium stannate trihydrate as a heterogeneous transesterification catalyst. Earlier elution of block copolymer from macro‐initiator in size exclusion chromatography (SEC) indicated the successful synthesis of the block copolymers. Ratios of both types of blocks are varied systematically. Liquid chromatography at critical conditions is used for the analysis of the non‐critical individual blocks, and if there are any critical segments that are not attached to the non‐critical block. To the best of our knowledge, this is the first report on the synthesis of ethylene carbonate‐based amphiphilic block copolymers. Chromatographic critical conditions of the ethylene carbonate polymer are also reported for the first time. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1887–1893