Isoindigo‐3,4‐Difluorothiophene Polymer Acceptors Yield “All‐Polymer” Bulk‐Heterojunction Solar Cells with over 7 % Efficiency

Poly(isoindigo‐alt‐3,4‐difluorothiophene) (PIID[2F]T) analogues used as “polymer acceptors” in bulk‐heterojunction (BHJ) solar cells achieve >7 % efficiency when used in conjunction with the polymer donor PBFTAZ (model system; copolymer of benzo[1,2‐b:4,5‐b′]dithiophene and 5,6‐difluorobenzotriazole). Considering that most efficient polymer‐acceptor alternatives to fullerenes (e.g. PC₆₁BM or its C₇₁ derivative) are based on perylenediimide or naphthalenediimide motifs thus far, branched alkyl‐substituted PIID[2F]T polymers are particularly promising non‐fullerene candidates for “all‐polymer” BHJ solar cells.     

Synthesis and properties of mono‐ and di‐fluoro‐substituted 2,3‐didodecylquinoxaline‐based polymers for polymer solar cells

We synthesized two new alternating polymers, namely P(Tt‐FQx) and P(Tt‐DFQx) , incorporating electron rich tri‐thiophene and electron deficient 6‐fluoroquinoxaline or 6,7‐difluoroquinoxaline derivatives. Both polymers P(Tt‐FQx) and P(Tt‐DFQx) exhibited high thermal stabilities and the estimated 5% weight loss temperatures are 425 and 460 °C, respectively. Polymers P(Tt‐FQx) and P(Tt‐DFQx) displayed intense absorption band between 450 and 700 nm with an optical band gap (E_g) of 1.78 and 1.80 eV, respectively. The determined highest occupied/lowest unoccupied molecular orbital's (HOMO/LUMO) of P(Tt‐DFQx) (?5.48 eV/?3.68 eV) are slightly deeper than those of P(Tt‐FQx) ( ?5.32 eV/?3.54 eV). The polymer solar cells fabricated with a device structure of ITO/PEDOT:PSS/ P(Tt‐FQx) or P(Tt‐DFQx) :PC₇₀BM (1:1.5 wt %) + 3 vol % DIO/Al offered a maximum power conversion efficiency (PCE) of 3.65% with an open‐circuit voltage (V_oc) of 0.59 V, a short‐circuit current (J_sc) of 10.65 mA/cm² and fill factor (FF) of 59% for P(Tt‐FQx) ‐based device and a PCE of 4.36% with an V_oc of 0.69 V, a J_sc of 9.92 mA/cm², and FF of 63% for P(Tt‐DFQx) ‐based device. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 545–552     

13.34 % Efficiency Non‐Fullerene All‐Small‐Molecule Organic Solar Cells Enabled by Modulating the Crystallinity of Donors via a Fluorination Strategy

Non‐fullerene all‐small‐molecule organic solar cells (NFSM‐OSCs) have shown potential as OSCs, owing to their high purity, easy synthesis and good reproducibility. However, challenges in the modulation of phase separation morphology have limited their development. Herein, two novel small molecular donors, BTEC‐1F and BTEC‐2F, derived from the small molecule DCAO3TBDTT, are synthesized. Using Y6 as the acceptor, devices based on non‐fluorinated DCAO3TBDTT showed an open circuit voltage (V_oc) of 0.804 V and a power conversion efficiency (PCE) of 10.64 %. Mono‐fluorinated BTEC‐1F showed an increased V_oc of 0.870 V and a PCE of 11.33 %. The fill factor (FF) of di‐fluorinated BTEC‐2F‐based NFSM‐OSC was improved to 72.35 % resulting in a PCE of 13.34 %, which is higher than that of BTEC‐1F (61.35 %) and DCAO3TBDTT (60.95 %). To our knowledge, this is the highest PCE for NFSM‐OSCs. BTEC‐2F had a more compact molecular stacking and a lower crystallinity which enhanced phase separation and carrier transport.     

Dithienosilole–phenylquinoxaline‐based copolymers with A‐D‐A‐D and A‐D structures for polymer solar cells

Two copolymers having D‐A‐D‐A ( P1 ) and D‐A ( P2 ) structures with quinoxaline acceptor unit and dithienosilole donor unit were synthesized and their optical and electrochemical (both experimental and theoretical) properties were investigated. The optical properties showed that these copolymers P1 and P2 exhibit optical bandgaps of 1.54 and 1.62 eV, respectively, with broader absorption profiles extending up to 800 nm and 770 nm, respectively. The electrochemical investigation of these two copolymers indicates that they exhibit suitable highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels for efficient exciton dissociation and high open circuit voltage in the resultant polymer solar cells (PSCs). These copolymers were used as donors along with the PC₇₁BM as acceptor for the fabrication of solution processed bulk heterojunction PSCs. The optimized P1 :PC₇₁BM and P2 :PC₇₁BM active layers treated with solvent vapor treatment showed overall power conversion efficiency (PCE) of 7.16% and 6.57%, respectively. The higher PCE of P1 ‐based device as compared to P2 might be attributed to higher crystallinity of P1 and good hole mobility resulting more balanced charge transport. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 376–386     

A High‐Voltage Molecular‐Engineered Organic Sensitizer–Iron Redox Shuttle Pair: 1.4 V DSSC and 3.3 V SSM‐DSSC Devices

The development of high voltage solar cells is an attractive way to use sunlight for solar‐to‐fuel devices, multijunction solar‐to‐electric systems, and to power limited‐area consumer electronics. By designing a low‐oxidation‐potential organic dye ( RR9 )/redox shuttle (Fe(bpy)₃^3+/2+) pair for dye‐sensitized solar‐cell (DSSC) devices, the highest single device photovoltage (1.42 V) has been realized for a DSSC not relying on doped TiO₂. Additionally, Fe(bpy)₃^3+/2+ offers a robust, readily tunable ligand platform for redox potential tuning. RR9 can be regenerated with a low driving force (190 mV), and by utilizing the RR9 /Fe(bpy)₃^3+/2+ redox shuttle pair in a subcell for a sequential series multijunction (SSM)‐DSSC system, one of the highest known three subcell photovoltage was attained for any solar‐cell technology (3.34 V, >1.0 V per subcell).     

A Simple 3,4‐Ethylenedioxythiophene Based Hole‐Transporting Material for Perovskite Solar Cells

We report a novel electron‐rich molecule based on 3,4‐ethylenedioxythiophene (H101). When used as the hole‐transporting layer in a perovskite‐based solar cell, the power‐conversion efficiency reached 13.8 % under AM 1.5G solar simulation. This result is comparable with that obtained using the well‐known hole transporting material 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD). This is the first heterocycle‐containing material achieving >10 % efficiency in such devices, and has great potential to replace the expensive spiro‐OMeTAD given its much simpler and cheaper synthesis.     

2,1,3‐benzothiadiazole‐5,6‐dicarboxylicimide based semicrystalline polymers for photovoltaic cells

Two semicrystalline low band gap polymers based on highly electron‐deficient 2,1,3‐benzothiadiazole‐5,6‐dicarboxylicimide (BTI) were synthesized by considering the chain planarity via intrachain noncovalent coulombic interactions. The thiophene‐BTI and thienothiophene‐BTI based PPDTBTI and PPDTTBTI have a low band gap (～1.5 eV) via strong intramolecular charge transfer interaction, showing a broad light absorption covering 300～850 nm. Semicrystalline film morphology was observed for both polymers in the grazing incidence wide angle X‐ray scattering measurements. Interestingly, PPDTBTI showed a pronounced edge on packing structure but PPDTTBTI showed predominantly a face on orientation in both pristine and blend films. Different packing patterns influenced significantly the charge carrier transport, recombination and resulting photovoltaic characteristics. The best power conversion efficiency was measured to be 5.47% for PPDTBTI and 6.78% for PPDTTBTI, by blending with the fullerene derivative, PC₇₁BM. Compared to the PPDTBTI blend, PPDTTBTI: PC₇₁BM suffered from the lower open‐circuit voltage but showed the substantially higher hole mobility and short‐circuit current density with smaller charge recombination, showing very good agreements with molecular structures and morphological characteristics. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3826–3834     

Efficient Diketopyrrolopyrrole‐Based Small‐Molecule Bulk‐Heterojunction Solar Cells with Different Electron‐Donating End‐Groups

A series of small molecules that contained identical π‐spacers (ethyne), a central diketopyrrolopyrrole (DPP) unit, and different aromatic electron‐donating end‐groups were synthesized and used in organic solar cells (OSCs) to study the effect of electron‐donating groups on the device performance. The three compounds, DPP‐A‐Ph , DPP‐A‐Na , and DPP‐A‐An , possessed intense absorption bands that covered a wide range, from 350 to 750 nm, and relatively low HOMO energy levels, from ?5.50 to ?5.55 eV. DPP‐A‐An , which contained anthracene end‐groups, demonstrated a stronger absorbance and a higher hole mobility than DPP‐A‐Ph , which contained phenyl groups, and DPP‐A‐Na , which contained naphthalene units. The power‐conversion efficiencies (PCEs) of OSCs based on organic:PC₇₁BM blends (1:1, w/w) with a processed DIO additive were 3.93 % for DPP‐A‐An , 3.02 % for DPP‐Na , and 2.26 % for DPP‐A‐Ph . These findings suggest that a DPP core that is functionalized with electron‐donating capping groups constitutes a promising new class of solution‐processable small molecules for OSC applications.     

Beyond Perovskite Solar Cells: Tellurium Iodide as a Promising Light‐Absorbing Material for Solution‐Processed Photovoltaic Application

Searching new light‐absorbing materials to replace toxic lead halide in solar cells is very important and highly desirable. In this research, we firstly demonstrated that tellurium iodide (TeI₄) could be used as a light‐absorbing material in solar cells due to its suitable optical band gap and the active lone‐pair electron orbital in Te⁴⁺. The best power conversion efficiency (PCE=3.56%) was achieved with a concentration of 0.9 M TeI₄ in DMF:DMSO (4 : 1, v,v) without any heat treatment or antisolvent dripping. Our study indicates the promising potential of TeI₄ for photovoltaic and optoelectronic applications.     

Three Keggin‐Type Transition Metal‐Substituted Polyoxometalates as Pure Inorganic Photosensitizers for p‐Type Dye‐Sensitized Solar Cells

In light of the serious challenge of severe global energy shortages, p‐type dye‐sensitized solar cells (p‐DSSCs) have attracted increasing levels of interest. The potential of three Keggin‐type transition metal‐substituted polyoxometalates, TBA₈Na₂[SiW₉O₃₇{Co(H₂O)₃}]? 11 H₂O (SiW₉Co₃), TBA₄[(SiO₄)W₁₀Mn^III₂O₃₆H₆]?1.5 CH₃CN? 2 H₂O (SiW₁₀Mn^III₂), and TBA_3.5H_5.5[(SiO₄)W₁₀Mn^III/IV₂O₃₆]? 10 H₂O?0.5 CH₃CN (SiW₁₀Mn^III/IV₂) has been explored as pure inorganic dye photosensitizers for p‐DSSCs (TBA=(n‐C₄H₉)₄N⁺). The three dyes show overall conversion efficiencies of 0.038, 0.029, and 0.027 %, respectively, all of which are higher than that of coumarin 343 (0.017 %). These polyoxometalates are the first three pure inorganic dyes reported for use with p‐DSSCs and therefore demonstrate a new strategy for designing efficient dyes, especially pure inorganic dyes. Moreover, they broaden the range of applications for polyoxometalates.     

High‐Performance Organic Materials for Dye‐Sensitized Solar Cells: Triarylene‐Linked Dyads with a 4‐tert‐Butylphenylamine Donor

A series of organic dyes were prepared that displayed remarkable solar‐to‐energy conversion efficiencies in dye‐sensitized solar cells (DSSCs). These dyes are composed of a 4‐tert‐butylphenylamine donor group (D), a cyanoacrylic‐acid acceptor group (A), and a phenylene‐thiophene‐phenylene (PSP) spacer group, forming a D‐π‐A system. A dye containing a bulky tert‐butylphenylene‐substituted carbazole (CB) donor group showed the highest performance, with an overall conversion efficiency of 6.70 %. The performance of the device was correlated to the structural features of the donor groups; that is, the presence of a tert‐butyl group can not only enhance the electron‐donating ability of the donor, but can also suppress intermolecular aggregation. A typical device made with the CB‐PSP dye afforded a maximum photon‐to‐current conversion efficiency (IPCE) of 80 % in the region 400–480 nm, a short‐circuit photocurrent density J_sc=14.63 mA cm^?2, an open‐circuit photovoltage V_oc=0.685 V, and a fill factor FF=0.67. When chenodeoxycholic acid (CDCA) was used as a co‐absorbent, the open‐circuit voltage of CB‐PSP was elevated significantly, yet the overall performance decreased by 16–18 %. This result indicated that the presence of 4‐tert‐butylphenyl substituents can effectively inhibit self‐aggregation, even without CDCA.     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

A Purified,Solvent‐Intercalated Precursor Complex for Wide‐Process‐Window Fabrication of Efficient Perovskite Solar Cells and Modules

A high‐purity methylammonium lead iodide complex with intercalated dimethylformamide (DMF) molecules, CH₃NH₃PbI₃?DMF, is introduced as an effective precursor material for fabricating high‐quality solution‐processed perovskite layers. Spin‐coated films of the solvent‐intercalated complex dissolved in pure dimethyl sulfoxide (DMSO) yielded thick, dense perovskite layers after thermal annealing. The low volatility of the pure DMSO solvent extended the allowable time for low‐speed spin programs and considerably relaxed the precision needed for the antisolvent addition step. An optimized, reliable fabrication method was devised to take advantage of this extended process window and resulted in highly consistent performance of perovskite solar cell devices, with up to 19.8 % power‐conversion efficiency (PCE). The optimized method was also used to fabricate a 22.0 cm², eight‐cell module with 14.2 % PCE (active area) and 8.64 V output (1.08 V/cell).     

Quantum‐Dot‐Sensitized Solar Cells

Quantum‐dot‐sensitized solar cells (QDSCs) are a promising low‐cost alternative to existing photovoltaic technologies such as crystalline silicon and thin inorganic films. The absorption spectrum of quantum dots (QDs) can be tailored by controlling their size, and QDs can be produced by low‐cost methods. Nanostructures such as mesoporous films, nanorods, nanowires, nanotubes and nanosheets with high microscopic surface area, redox electrolytes and solid‐state hole conductors are borrowed from standard dye‐sensitized solar cells (DSCs) to fabricate electron conductor/QD monolayer/hole conductor junctions with high optical absorbance. Herein we focus on recent developments in the field of mono‐ and polydisperse QDSCs. Stability issues are adressed, coating methods are presented, performance is reviewed and special emphasis is given to the importance of energy‐level alignment to increase the light to electric power conversion efficiency.     

Donor‐π‐Acceptors Containing the 10‐(1,3‐Dithiol‐2‐ylidene)anthracene Unit for Dye‐Sensitized Solar Cells

Two donor–acceptor molecular tweezers incorporating the 10‐(1,3‐dithiol‐2‐ylidene)anthracene unit as donor group and two cyanoacrylic units as accepting/anchoring groups are reported as metal‐free sensitizers for dye‐sensitized solar cells. By changing the phenyl spacer with 3,4‐ethylenedioxythiophene (EDOT) units, the absorption spectrum of the sensitizer is red‐shifted with a corresponding increase in the molar absorptivity. Density functional calculations confirmed the intramolecular charge‐transfer nature of the lowest‐energy absorption bands. The new dyes are highly distorted from planarity and are bound to the TiO₂ surface through the two anchoring groups in a unidentate binding form. A power‐conversion efficiency of 3.7 % was obtained with a volatile CH₃CN‐based electrolyte, under air mass 1.5 global sunlight. Photovoltage decay transients and ATR‐FTIR measurements allowed us to understand the photovoltaic performance, as well as the surface binding, of these new sensitizers.     

Anthracene‐Containing Wide‐Band‐Gap Conjugated Polymers for High‐Open‐Circuit‐Voltage Polymer Solar Cells

The synthesis, characterization, and photophysical and photovoltaic properties of two anthracene‐containing wide‐band‐gap donor and acceptor (D–A) alternating conjugated polymers ( P1 and P2 ) are described. These two polymers absorb in the range of 300–600 nm with a band gap of about 2.12 eV. Polymer solar cells with P1 :PC₇₁BM as the active layer demonstrate a power conversion efficiency (PCE) of 2.23% with a high V_oc of 0.96 V, a J_sc of 4.4 mA cm⁻², and a comparable fill factor (FF) of 0.53 under simulated solar illumination of AM 1.5 G (100 mW cm⁻²). In addition, P2 :PC₇₁BM blend‐based solar cells exhibit a PCE of 1.42% with a comparable V_oc of 0.89 V, a J_sc of 3.0 mA cm⁻², and an FF of 0.53.

     

Amorphous Hole‐Transporting Material based on 2,2′‐Bis‐substituted 1,1′‐Biphenyl Scaffold for Application in Perovskite Solar Cells

Perovskite solar cells are considered a promising technology for solar‐energy conversion, with power conversion efficiencies currently exceeding 20 %. In most of the reported devices, Spiro‐OMeTAD is used for positive‐charge extraction and transport layer. Although a number of alternative hole‐transporting materials with different aromatic or heteroaromatic fragments have already been synthesized, a cheap and well‐performing hole‐transporting material is still in high demand. In this work, a two‐step synthesis of a carbazole‐based hole‐transporting material is presented. Synthesized compounds exhibited amorphous nature, good solubility and thermal stability. The perovskite solar cells employing the newly synthesized material generated a power conversion efficiency of 16.5 % which is slightly lower than that obtained with Spiro‐OMeTAD (17.5 %). The low‐cost synthesis and high performance makes our hole‐transport material promising for applications in perovskite‐based optoelectronic devices.     

Silaindacenodithiophene‐Based Fused‐Ring Non‐Fullerene Electron Acceptor for Efficient Polymer Solar Cells

In this work, a new A‐D‐A type nonfullerene small molecular acceptor SiIDT‐IC, with a fused‐ring silaindacenodithiophene (SiIDT) as D unit and 2‐(3‐oxo‐2,3‐dihydroinden‐1‐ylidene)malononitrile (INCN) as the end A unit, was design and synthesized. The SiIDT‐IC film shows absorption peak and edge at 695 and 733 nm, respectively. The HOMO and LUMO of SiIDT‐IC are of −5.47 and −3.78 eV, respectively. Compared with carbon‐bridging, the Si‐bridging can result in an upper‐lying LUMO level of an acceptor, which is benefit to achieve a higher open‐circuit voltage in polymer solar cells (PSCs). Complementary absorption and suitable energy level alignment between SiIDT‐IC and wide bandgap polymer donor PBDB‐T were found. For the PBDB‐T:SiIDT‐IC based inverted PSCs, a D/A ratio of 1: 1 was optimal to achieve a power conversion efficiency (PCE) of 7.27%. With thermal annealing (TA) of the blend film, a higher PCE of 8.16% could be realized due to increasing of both short‐circuit current density and fill factor. After the TA treatment, hole and electron mobilities were elevated to 3.42 × 10⁻⁴ and 1.02 × 10⁻⁴ cm²·V⁻¹·s⁻¹, respectively. The results suggest that the SiIDT, a Si‐bridged fused ring, is a valuable D unit to construct efficient nonfullerene acceptors for PSCs.     

Thieno[3,4‐c]pyrrole‐4,6‐dione‐3,4‐difluorothiophene Polymer Acceptors for Efficient All‐Polymer Bulk Heterojunction Solar Cells

Branched‐alkyl‐substituted poly(thieno[3,4‐c]pyrrole‐4,6‐dione‐alt‐3,4‐difluorothiophene) (PTPD[2F]T) can be used as a polymer acceptor in bulk heterojunction (BHJ) solar cells with a low‐band‐gap polymer donor (PCE10) commonly used with fullerenes. The “all‐polymer” BHJ devices made with PTPD[2F]T achieve efficiencies of up to 4.4 %. While, to date, most efficient polymer acceptors are based on perylenediimide or naphthalenediimide motifs, our study of PTPD[2F]T polymers shows that linear, all‐thiophene systems with adequately substituted main chains can also be conducive to efficient BHJ solar cells with polymer donors.