A new configuration for coupling purge-and-trap/cryogenic focusing/capillary column gas chromatography with splitless injection mode

A new configuration for coupling a purge-and-trap unit to a capillary column gas chromatograph via a cryogenic focusing interface has been developed. In this configuration, the precolumn of the cryogenic focusing interface was inserted through the septum of a split/splitless injection port where it served as both sample transfer and carrier gas supply lines. The injection port of the gas chromatograph was modified by plugging the carrier gas and the septum purge lines. This configuration allowed for the desorption of analytes at high flow rates while maintaining low, analytical-column flow rates which are necessary for optimum capillary column operation. The capillary column flow rate is still controlled by the column backpressure regulator. Chromatograms of purgeable aromatics exhibited improved resolution, especially for early eluting components compared to those obtained by direct liquid injection using the normal splitless injection mode. Quantitative sample transfer to the analytical column afforded excellent linearity and reproducibility of compounds studied.     

Evaporation of the liquid stationary phase in gas chromatography

Summary The theory of the evaporation of the liquid stationary phase is elaborated and experimentally verified. On the basis of this theory the role played by the losses in the amount of liquid phase present is quantitatively determined. General techniques are examined which minimize the losses; these techniques are based on saturating the incoming carrier gas with liquid phase vapours and raising the pressure of the carrier gas in the column, e.g. by connecting a capillary to the column outlet in order to offer resistance to the gas flow. The application of these techniques ensures stable performance of the gas chromatographic columns using a volatile liquid phase.     

Chromatographic efficiency of polar capillary columns applied for the analysis of fatty acid methyl esters by gas chromatography

The chromatographic efficiency that could be achieved in temperature‐programmed gas chromatography was compared for four capillary columns that are typically applied for analysis of fatty acid methyl esters (FAME). Three different carrier gases, hydrogen, helium and nitrogen, were applied. For each experiment, the carrier gas velocities and the temperature rates were varied with a full 9 × 3 design, with nine levels on the carrier gas velocity and temperature rates of 1, 2 or 3°C/min. Response surface methodology was used to create models of chromatographic efficiency as a function of temperature rate and carrier gas velocity. The chromatographic efficiency was defined as the inverse of peak widths measured in retention index units. The final results were standardized so that the efficiencies that could be achieved within a certain time frame, defined by the retention time of the last compound in the chromatogram, could be compared. The results show that there were clear differences in the efficiencies that could be achieved with the different columns and that the efficiency decreased with increasing polarity of the stationary phase. The differences can be explained by higher resistance to mass transfer in the stationary phase in the most polar columns.     

Application of fused-silica capillary gas chromatography to the analysis of underivatized drugs

The feasibility of using fused-silica capillary chromatography for the routine analysis of several common drugs is illustrated. Considerations for optimizing on-column and splitless injection are discussed as part of a study of system discrimi nation and reproducibility. The peak shape of polar solutes is improved through the use of a binary solvent and non-extractable stationary phase columns. Cold on-column injection with cross-linked polysiloxane deactivated columns produced linear quantitation from 1 to 100 ng with precisions of 0.1–2% for selected anticonvulsant drugs.     

Dependence of the relative retention of organic compounds on the nature and pressure of the carrier gas and on the thickness of the PEG-20M film in the capillary column

The effects of the carrier gas nature and pressure on the relative retention values of organic compounds were studied using a series of capillary columns differing in the film thickness of the polar stationary phase (PEG-20M). Relative retention depends linearly on the carrier gas pressure. This dependence becomes more pronounced in the following order of carrier gases: helium < nitrogen < carbon dioxide. The limiting relative retention at a carrier gas pressure approaching zero rather than relative retention values measured experimentally (relative retention time, Kovats retention index,etc.) is an invariant characteristic of a compound subjected to chromatography. For the carrier gases studied, the limiting retention values almost does not depend on the nature of the carrier gas used. The limiting indicating the complex absorption-adsorption nature of these parameters. Dissolution of a carrier gas in the stationary liquid phase has an effect on the relative retention. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2177–2186, December, 1997.     

Influence of a water vapor admixture in the carrier gas on capacity coefficients of polar organic compounds

The influence of a water vapor admixture in helium, nitrogen, and carbon dioxide on capacity coefficients of C₃−C₅ alcohols and pyridine during chromatography process in capillary columns with polar (PEG-20M) and nonpolar (SE-30) stationary phases was studied. The introduction of a water admixture into the carrier gas, increases the capacity coefficient of polar organic compounds on the capillary column with PEG-20M and has almost no effect on this value in the case of SE-30. The change in retention of polar organic compounds on the capillary column with the PEG-20M polar phase occurs due to a change in the properties of the stationary phase when it adsorbs water from the mobile phase. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 2258–2261, November, 1998.     

填充毛细管液相色谱-毛细管气相色谱在线联用分析八角茴香挥发油

首次将填充毛细管高效液相色谱-毛细管气相色谱在线联用技术(μ-HPLC-CGC)用于分离分析八角茴香果实的挥发油成分。液相色谱选用氰基分析柱(250 mm×0.32 mm i.d.),正己烷-乙腈-二氯甲烷(体积比为80∶8∶12)为流动相,对挥发油样品做族组分分离,得到的5个族组分被依次存放在多位储存接口内,然后不分流分别转入毛细管气相色谱仪做详细分析。气相色谱柱由10 m×0.53 mm i.d.保留间隔柱和30 m×0.53 mm i.d.×1.0 μm SE-54分析柱组成。采用了不分流柱内进样模     

Direct injection of large sample volumes into capillary columns with packed column injector

A direct injection method for large volume samples which avoids severe tailing of the solvent peak has been developed using a packed column injector (up to 100 μl) leading into an ordinary capillary column (0.3 mm i.d.). Modifications are made to the cooler zones of the inlet port and on the carrier gas flow control system. This injection technique is based on the effective use of phase soaking and cold trapping using a retention gap. The large volume of solvent vapor is rapidly purged out of the injector with a higher flow of carrier gas while the solutes trapped at the head of the column are subsequently analyzed with another optimum flow rate. The proposed carrier gas flow regulation system is also compared with conventional split/splitless injection methods.     

Differentiation between dexamethasone and betamethasone in a mixture using multiple mass spectrometry

Direct gas chromatographic methods to analyse phenylurea pesticides are discouraged by the thermal instability of these compounds, that in conventional hot splitless inlet systems leads to extensive and irreproducible formation of isocyanates and amines. However a careful control of the operating conditions, like the inlet temperature, the pressure and the presence of suitable chemical additives (as acetic acid, low-molecular-mass amines, organic anhydrides) can either: (i) minimise the thermal decomposition enabling the direct GC-MS analysis of phenylureas, or (ii) lead to reproducible conversion to isocyanates. Experimental design was employed to study the effect of the experimental variables on the thermal transformation of phenylurea pesticides in splitless inlet system. Two strategies were alternatively optimised: (i) the minimisation of degradation reactions to increase the signal of phenylureas; (ii) the maximisation of the degradation to isocyanates that are in turn determined. The maximal yields in isocyanate were obtained with high inlet temperatures, low carrier flows in the injection phase and the presence of acetic anhydride. By contrast, the use of relatively low inlet temperatures, high carrier flows during the injection and the presence of an amine maximise the response of the parent compounds.     

High resolution gas chromatography of tobacco smoke: The contributions of kurt grob

The contributions made by Kurt Grob to tobacco science are reviewed with emphasis on the application of high resolution gas chromatography to tobacco smoke analysis. Highlighted are his pioneering achievements in the preparation and use of glass capillary columns, GC-MS, and splitless injection.     

Possibilities and limitations of fast GC with narrow-bore columns

In this work, two narrow-bore capillary columns with different internal diameters (I.D.) 0.15 mm (15 m length, 0.15 microm film thickness) and 0.10 mm (10 m length, 0.10 microm film thickness) with the same stationary phase (5% diphenyl 95% dimethylsiloxane), phase ratio and separation power were compared with regard to their advantages, practical limitations and applicability in fast GC on commercially available instrumentation. The column comparison concerns fast GC method development, speed and separation efficiency, the sample transfer into the column utilizing split and splitless inlet, sample capacity, detection (analysing compounds of a wide range of polarities and volatilities--even n-alkanes C16-C28 and selected pesticides) and ruggedness (in the field of ultratrace analysis of pesticide residues in real matrix). Under conditions corresponding to speed/separation efficiency trade-off 0.10 mm I.D. versus 0.15 mm I.D. column provides a speed gain of 1.74, but all other parameters investigated were better for the 0.15 mm I.D. column concerning more efficient sample transfer from inlet to the column using splitless injection, no discrimination with split injection. Better sample capacity (three times higher for the 0.15 mm than for the 0.10 mm I.D. column) resulted in improved ruggedness and simpler fast GC-MS method development.     

A study of the efficiency of monolithic silica gel capillary columns for gas chromatography

The efficiency and dynamic characteristics of seven silica-gel-based monolithic capillary columns were analyzed by separating on them a mixture of five light hydrocarbons. For helium carrier gas flowing at an optimum velocity, the height equivalent to a theoretical plate was found to be 0.15–0.20 mm, values comparable to those typical of packed capillary columns. An analysis of the Van Deemter curves for the columns under study demonstrated that the main contribution to the smearing of the chromatographic zone comes from the diffusional processes in the mobile phase while the mass transfer between the mobile and stationary phases plays only a minor role. At the same time, the parameter A in the Van Deemter equation, which characterizes the degree of column packing uniformity, was found to be negative. This result contradicts the classical theory of chromatography and calls for further studies of monolithic capillary columns.     

Determination of biogenic quaternary ammonium compounds on fused silica capillary columns with a splitless injector as a chemical reactor/pyrolysis chamber

A conventional splitless injector is used as a pyrolysis chamber or chemical reactor for the N-demethylation of acetylcholine and other choline esters. The novel uses of 2-aminoethanol as a N-demethylation reagent in splitless injection and bonded-phase fused silica capillary columns in the separation of the tertiary amine derivatives of choline esters are described. A comparison is made between non-polar and moderately polar fused silica capillary columns in the separation of choline esters.     

Separation of rhubarb anthraquinones by capillary electrochromatography

Summary A rapid, simple method for packing capillary electrochromatography (CEC) columns with HPLC stationary phases is described. The basis of the method is the use of a vacuum to suck a slurry of stationary phase into the fused-silica tubing, a procedure which takes approximately ten seconds only, then compression of the stationary phase by means of an HPLC pump. These packed CEC columns have been investigated for the separation of five anthraquinones from rhubarb. Separation of the anthraquinones inRheum palmatum L. under optimized conditions is presented.     

Gas Chromatographic Separation of Carbonyl Compounds as Their 2,4-dinitrophenylhydrazones Using Glass Capillary Columns

The gas chromatographic separation of 22 carbonyl compounds as their 2,4-dinitrophenylhydrazones was investigated using glass capillary columns. Complete separation of the 2,4-dinitrophenylhydrazones of ten aliphatic aldehydes, eight aliphatic ketones and four aromatic aldehydes was obtained, except for the derivatives of n-valeraldehyde and isobutyl methyl ketone, whose peaks overlapped, and the o- and m-tolualdehyde derivatives, which were poorly separated. The optimum conditions were as follows: stationary phase, SF-96; column size, 20 m × 0.25 mm I.D. ; column temperature, 200-240°; injection and detector temperatures, 280-290°; carrier gas flow-rate, helium 1.0-1.2 ml/min or nitrogen 1.1-1.2 ml/min. The method was applied to the analysis of aliphatic carbonyl compounds in car exhaust fumes and cigarette smoke.     

环糊精-聚硅氧烷共聚物溶胶-凝胶气相色谱毛细管柱分离特性研究

用环糊精与低聚硅氧烷的共聚物为固定相制成了溶胶-凝胶毛细管气相色谱柱。比较了支臂与环糊精的不同位置（6^A6^C与6^A6^D）相连接的共聚物为固定相的手性分离的区别,也比较了不同的臂长和不同的臂结构对手性化合物拆分产生的影响。结果表明：含有4个亚甲基和醚键结构的连接臂且与环糊精的6^A6^C位置相连接的共聚物是这几种结构中的最佳固定相。     

A new type of capillary column for gas chromatography

A new type of capillary column for gas chromatography was proposed. A sorbent layer (for example, stationary liquid phase) is supported on the internal capillary surface, and the internal (interstitial) volume is packed with nonporous large particles of a sorbent (particle diameter is 0.1—0.6 of the capillary internal diameter). The external surface of the particles can also be coated with the sorbent layer (for example, stationary liquid phase). The specific separation efficiency (number of separation) on the new type column is by 1.6—2.3 times higher than that of the initial classical capillary column.     

Optimized preparation of poly(styrene-co- divinylbenzene-co-methacrylic acid) monolithic capillary column for capillary electrochromatography

Preparation of a poly(styrene-co-divinylbenzene-co-methacrylic acid) monolithic stationary phase for the use in capillary electrochromatography (CEC) has been improved by optimizing the polymerization conditions. It is observed that the reaction time strongly affects column efficiency, while the proportion of isooctane in porogen influences peak symmetry of some solutes seriously. The lifetime of the monolithic columns prepared mainly depends on the pH of buffers used. Reproducibility of electroosmotic flow (EOF) from batch to batch columns are lower than 2.8% relative standard deviation. Unlike other types of capillary electrochromatographic monoliths, a pH-dependent EOF was observed on this type of column. Separation of various types of compounds including aromatic hydrocarbons, hormones, anilines, basic pharmaceuticals, and peptides was achieved. The facile preparation and wide application of this monolithic column may make styrene-based polymer a potential stationary phase in CEC.     

Temperature program optimization by computer simulation for the capillary GC analysis of fatty acid methyl esters on biscyanopropyl siloxane phases

The selectivity of capillary columns coated with biscyanopropyl siloxane stationary phases for the separation of fatty acid methyl esters has been optimized by means of computer-assisted column temperature optimization software. Temperature programming rates yielding the highest resolution in the shortest analysis time were selected for split, splitless, and on-column injection operated in the constant pressure and pressure programmed modes.     

Polar monolithic capillary columns: Analysis of light hydrocarbons

The influence of the nature of the stationary phase and carrier gas (helium, hydrogen, nitrogen, carbon dioxide, or nitrous oxide) on the efficiency and separating ability of monolithic ethyleneglycol dimethacrylate (EDMA) polymer capillary columns was studied using a model mixture of light hydrocarbons C₁-C₄. The results were compared with the properties of silica gel and divinylbenzene (DVB) monolithic columns. For EDMA polymer monolithic columns, the effect of the carrier gas on the separating ability was markedly lower than for silica gel columns. A reduction in HETP observed in the series He > H₂ > N₂ > N₂O > CO₂ is also known for hollow capillary columns with polymer stationary phases, but the change in efficiency was ～20–30% in this case. Under the optimum conditions, HETP was minimum for the columns when CO₂ or N₂O was used.