High-speed visualization and PIV measurements of cavitating flows around a semi-circular leading-edge flat plate and NACA0015 hydrofoil

Cavitating flows around a flat plate with semi-circular leading edge and a NACA0015 hydrofoil at attack angles ranging from 0° to 9° and with varying cavitation number are investigated using high-speed-imaging visualization (HIV) and particle-imaging velocimetry (PIV). Several known types of cavitation common to both foils, but also some different patterns, were observed. At small angles of incidence (less than 3°), cavitation on the plate begins in the form of a streak array (bubble-band) whereas on the hydrofoil as traveling bubbles. For the regimes with developed cavitation on the NACA0015 hydrofoil, the scattered and discontinuous bubble streaks branch and grow but subsequently merge into bubble clouds forming a remarkably regular lattice pattern. Once the incidence angle increased to 9°, the cavitation on the hydrofoil changed to a streaky pattern like that on the plate at small attack angles, whereas the regime on the plate showed no significant changes. The PIV method proved to be usable for measuring the instantaneous velocity also in the gas–vapor phase, albeit with reduced accuracy that was evaluated and accounted for on the basis of the effective (validation-surviving) number of imaging samples. The time-averaged velocity and turbulence moments show that the incipience of cavitation is governed by the development of the carrier-fluid flow around the foil leading edges, but the subsequent flow pattern depends strongly on the cavitation regime displaying markedly different distributions compared to the non-cavitating case. The main cavitation parameters: the maximum cavity length, the cloud cavity streamwise dimensions and the cloud shedding Strouhal number are analyzed and presented in function of the cavitation number and the attack angle in different scaling. The measurements confirm qualitatively the trends reported in the literature, but show also some quantitative differences, notably between the two foils considered.     

绕水翼空化流动及振动特性的实验研究

空化是发生在水力机械内部的一种水动力现象,其发展具有显著的非定常特性.空化流动中空穴的脱落以及溃灭会诱发结构振动,对水力机械的效率、噪声、安全性等造成影响. 研究空化流动中结构的振动特性具有重要的工程意义. 采用实验的方法研究了绕NACA66 水翼空化流动的空穴形态和水翼振动特性. 实验在一闭式空化水洞中进行. 采用高速摄像技术观测不同空化阶段的空穴形态,应用多普勒激光测振仪测量水翼的振动速度,并通过一套同步系统实现了高速相机和多普勒激光测振仪的同步触发和测量. 采用小波分析方法对不同空化阶段下的空穴形态和水翼振动数据在时域和频域中的特性进行了分析.对云状空化阶段的同步测量结果进行了研究,分析了振动与空穴发展过程的联系. 结果表明,随着空化数的降低,流场经历了无空化、初生空化、片状空化和云状空化4个阶段,水翼的振动强度呈逐渐增大趋势. 在片状空化和云状空化阶段,空穴脱落导致水翼振动,诱发的振动频率与空穴脱落频率相同. 对于云状空化,在附着型空穴生长阶段水翼发生高频小幅度振动,在空穴脉动和断裂脱落期间水翼表现为低频大幅振动.      

Experimental evaluation of numerical simulation of cavitating flow around hydrofoil

Cavitation in hydraulic machines causes different problems that can be related to its unsteady nature. An experimental and numerical study of developed cavitating flow was performed. Until now simulations of cavitating flow were limited to the self developed “in house” CFD codes. The goal of the work was to experimentally evaluate the capabilities of a commercial CFD code (Fluent) for simulation of a developed cavitating flow. Two simple hydrofoils that feature some 3D effects of cavitation were used for the experiments. A relatively new technique where PIV method combined with LIF technique was used to experimentally determine the instantaneous and average velocity and void ratio fields (cavity shapes) around the hydrofoils. Distribution of static pressure on the hydrofoil surface was determined. For the numerical simulation of cavitating flow a bubble dynamics cavitation model was used to describe the generation and evaporation of vapour phase. An unsteady RANS 3D simulation was performed. Comparison between numerical and experimental results shows good correlation. The distribution and size of vapour structures and the velocity fields agree well. The distribution of pressure on the hydrofoil surface is correctly predicted. The numerically predicted shedding frequencies are in fair agreement with the experimental data.     

非定常空化流场结构的实验研究

为深入研究非定常空化流场结构,本文用实验方法研究了绕Clark-Y型水翼的非定常空化流动现象.实验在空化水洞中进行,采用高速摄像技术观测了云状空化阶段的非定常空穴形态,并应用粒子成像测速系统(PIV)对绕水翼空化流场的速度场和涡量场等流动特性进行了同步的实验分析.研究表明:空化现象对流场结构有着重要的影响,在无空化和空...     

Velocity field measurements of cavitating flows

A particle Image Velocimetry (PIV) system has been developed to study the microfluid mechanics of cavitating flows. Planar PIV was used to examine the non-cavitating flow in the thin boundary layer near a hydrofoil surface for the cases of a naturally developing boundary layer and a boundary layer stimulated to turbulence by roughness near the foil leading edge. PIV was also used to examine the flow near the surface of individual cavitation bubbles and incipient attached cavitation. A system was devised to create a single nucleus in the flow upstream of a hydrofoil, and planar PIV was used to study the flow around the resulting traveling cavitation bubble. Velocity vectors were determined close to the solid surfaces and the gas/liquid interfaces of the bubbles. Seeding of the flow with particles did not result in the addition of active cavitation nuclei.     

Statistical structure of the velocity field in cavitating flow around a 2D hydrofoil

Transformation of flow turbulence structure with cavitation occurrence, determination of the flow conditions favorable for nucleation of cavitation bubbles, influence of the statistical structure of turbulence on this process and the inverse effect of cavitation on the flow dynamics are challenging problems in modern fluid mechanics. The paper reports on the results of statistical processing of the velocity fields measured by a PIV technique in cavitating flow over a 2D symmetric hydrofoil for four flow conditions, starting from a cavitation-free regime and finishing by unsteady cloud cavitation. We analyze basic information on the statistical structure of velocity fluctuations in the form of histograms and Q-Q diagrams along with profiles of the mean velocity and turbulent kinetic energy. The research reveals that the flow turbulence pattern and distributions of turbulent fluctuations change significantly with the cavitation development. Under unsteady cloud cavitation conditions, the probability density function of the fluctuating velocity has a two-mode distribution, which indicates switching of two alternating flow conditions in a region above the hydrofoil aft part due to periodic passing of cavitation clouds. Behaviors of the mean and most probable velocities unexpectedly appear to be different with a monotonous increase of the incoming flow velocity. This finding must be caused by modification of the skewness coefficient of the fluctuating velocity.     

绕水翼空化流动多尺度数值研究

空化的多尺度效应是一种涉及连续介质尺度、微尺度空化泡以及不同尺度间相互转化的复杂水动力学现象, 跨尺度模型的构建是解析该多尺度现象的关键. 本文基于欧拉-拉格朗日联合算法, 通过界面捕捉法求解欧拉体系下大尺度空穴演化, 通过拉格朗日体系下离散空泡模型求解亚网格尺度离散空泡的运动及生长溃灭. 同时, 通过判断空泡与网格尺度间的关系判定不同尺度空化泡的求解模型. 基于建立的多尺度算法对绕NACA66水翼空化流动进行模拟, 将数值结果与实验进行对比, 验证了数值计算方法的准确性. 研究结果表明, 离散空泡数量与空化发展阶段密切相关, 在附着型片状空穴生长阶段, 离散空泡数量波动较小, 离散空泡主要分布在气液交界面位置; 在回射流发展阶段, 离散空泡逐渐增加并分布在回射流扰动区; 在云状空穴溃灭阶段, 离散空泡数量增多且主要分布在气液掺混剧烈的空化云团溃灭区. 在各空化发展阶段, 离散空泡直径概率密度函数均符合伽玛分布. 空化湍流流场特性对拉格朗日空泡空间分布具有重要影响, 离散空泡主要分布在强湍脉动区、旋涡及回射流发展区域.      

The influence of surface roughness on cloud cavitation flow around hydrofoils

The aim of this study is to investigate experimentally the effect of surface roughness on cloud cavitation around Clark-Y hydrofoils. High-speed video and particle image velocimetry(PIV) were used to obtain cavitation patterns images(Prog. Aerosp. Sci. 37: 551–581, 2001), as well as velocity and vorticity fields. Results are presented for cloud cavitating conditions around a Clark-Y hydrofoil fixed at angle of attack of α = 8?for moderate Reynolds number of Re = 5.6 × 10~5. The results show that roughness had a great influence on the pattern, velocity and vorticity distribution of cloud cavitation. For cavitating flow around a smooth hydrofoil(A) and a rough hydrofoil(B), cloud cavitation occurred in the form of finger-like cavities and attached subulate cavities, respectively. The period of cloud cavitation around hydrofoil A was shorter than for hydrofoil B.Surface roughness had a great influence on the process of cloud cavitation. The development of cloud cavitation around hydrofoil A consisted of two stages:(1) Attached cavities developed along the surface to the trailing edge;(2) A reentrant jet developed, resulting in shedding and collapse of cluster bubbles or vortex structure. Meanwhile, its development for hydrofoil B included three stages:(1) Attached cavities developed along the surface to the trailing edge, with accumulation and rotation of bubbles at the trailing edge of the hydrofoil affecting the flow field;(2) Development of a reentrant jet resulted in the first shedding of cavities. Interaction and movement of flows from the pressure side and suction side brought liquid water from the pressure side to the suction side of the hydrofoil, finally forming a reentrant jet. The jet kept moving along the surface to the leading edge of the hydrofoil, resulting in large-scale shedding of cloud bubbles. Several vortices appeared and dissipated during the process;(3) Cavities grew and shed again.     

绕水翼超空化流动形态与速度分布

为揭示超空化流场结构特性,利用高速全流场显示技术,观察了绕hydronautics水翼的超空化流动形态,并利用数字粒子图像测速仪(DPIV)测量了其速度分布. 在测量空穴内部流速分布时,采用空化流场中的空化泡作为示踪粒子来显示流动结构. 结果表明:随着空化数的降低,超空化流动显现出了明显的阶段特征,其中水汽混合相和汽相的分布决定了空化区域的形态与流速分布;空化区和主流区的汽液交界面处存在着较大的速度梯度;低速分布区域随着空化数的降低由水翼吸力面中后部向水翼下游移动;在空化区域内部,水汽混合区的速度相对较低,而汽相区则与主流区有着相近的速度分布.关键词超空化水翼、DPIV、高速摄像、空化形态、流速分布      

Experimental investigation of added mass effects on a hydrofoil under cavitation conditions

The influence of leading edge sheet cavitation and supercavitation on the added mass effects experienced by a 2-D NACA0009 truncated hydrofoil has been experimentally investigated in a hydrodynamic tunnel. A non-intrusive excitation and measuring system based on piezoelectric patches mounted on the hydrofoil surface was used to determine the natural frequencies of the fluid–structure system. The appropriate hydrodynamic conditions were selected to generate a range of stable partial cavities of various sizes and also to minimize the effects of other sources of flow noise and vibrations. The main tests were performed for different sigma values under a constant flow velocity of 14 m/s and for incident angles of both 1° and 2°. Additionally, a series of experiments in which the hydrofoil was submerged in air, partially and completely submerged in still water and without cavitation at 7 and 14 m/s were also performed. The maximum added mass effect occurs with still water. When cavitation appears, the added mass decreases because the cavity length is increased, and the added mass is minimum for supercavitation. A linear correlation is found between the added mass coefficients and the entrained mass that accounts for the mean density of the cavity, its dimensions and its location relative to the specific mode shape deformation.     

主动射流控制水翼空化的数值模拟与分析

为了改善高速流动工况下水翼吸力面上流场的空化特性,提出了水翼表面主动射流对绕水翼周围流动加以控制的方法.基于密度分域滤波的FBDCM混合湍流模型联合Zwart-Gerber-Belamri空化模型,分析了来流空化数为0.83,来流攻角为8°,射流位置距水翼前缘为x=0.19c时,主动射流对于水翼吸力面上流动的空化特性和水动力特性影响.对回射流的强度进行了量化分析,以探究回射流与流场空化特性的关系.数值分析结果表明,在射流水翼吸力面上的时均空泡体积为原始水翼的1/15,使得流场内空化流动由云空化状态转变为较为稳定的片空化状态,显著地削弱了云空化的发展.此外,射流极大地改善了水翼的水动力性能,使得水翼的升阻比较原始水翼提高了22.9%,空泡的脱落频率减少了26.2%,空泡脱落所引起的振幅减小了9.1%.射流大幅降低了水翼吸力面上低压区面积,水翼吸力面上流体的逆向压力减小,回射流强度降低;同时,射流使水翼吸力面上的边界层减薄,增强了流动的抗逆压梯度能力,一定程度上阻挡了回射流向水翼前缘的流动,这也从机理上分析了主动射流抑制空化的原因.      

Reduced-order modeling of three-dimensional unsteady partial cavity flows

An efficient reduced-order modeling to analyze three-dimensional unsteady partial cavity flows is proposed. The proposed approach is based on the boundary element method along with the potential flow assumption. To this end, a novel non-iterative method based on the flow eigenmodes of three-dimensional partial cavity flows is applied. Eigenanalysis and reduced-order modeling for unsteady flows over a three-dimensional hydrofoil with various sections are performed. The results obtained from the present analysis are compared with those reported in the literature to verify the strength of the proposed approach. In order to examine the performance of the introduced algorithm for unsteady cavitating flows, various simulations for several reduced frequencies, hydrofoil geometries and different cavitation numbers are also investigated. Comparison between the obtained results using the novel and conventional methods indicates that the present algorithm works very well with sufficient accuracy. Moreover, it is shown that the proposed method is computationally more efficient than the conventional ones for unsteady sheet cavitation analysis on three-dimensional hydrofoils.     

Influence of cavitation on the hydroelastic stability of hydrofoils

This work numerically examines the effect of turbulent and cavitating flow on the hydroelastic response and stability of a hydrofoil. A cantilevered, rectangular, chordwise rigid hydrofoil is modeled as a 2-degrees-of-freedom structure for its spanwise bending and torsional flexibilities. The fluid flow is modeled with the incompressible, Unsteady Reynolds Averaged Navier–Stokes equations using an eddy-viscosity turbulence closure model that is corrected for the presence of cavitation, and with a transport equation based cavitation model. The results show that, in general, massive cavitation tends to: (i) reduce the mean lift, (ii) increase the mean drag, (iii) lower the mean deformations, and (iv) delay static divergence, while unsteady sheet/cloud cavitation promotes flow induced vibrations. Such vibrations and load fluctuations could be as large as (and even greater than) the mean values for cases with unsteady cavitation, so dynamic and viscous fluid–structure models are needed to simulate flexible hydrofoils in cavitating flows. In general, the flow induced vibrations, and hence the drag force, are higher with decreasing stiffness. For small leading edge partial cavitation, increasing foil flexibility increases the maximum cavity length and reduces the cavity shedding frequency; however, the influence of foil flexibility is limited for cases where the maximum cavity length is near or beyond the foil trailing edge, because of the relocation of the center of pressure at the elastic axis, near the mid-chord. The results show that the mean deformations are generally limited by stall, and by the quasi-steady linear theory predictions at the fully-wetted and supercavitating limits. Furthermore, frequency focusing can occur when the cavity shedding frequency is near the fundamental system resonance frequencies, and broadening of the frequency spectrum can occur due to excitation of the sub-harmonics and/or modulation induced by the fluctuating cavities, if the cavity shedding frequency is away from the fundamental system resonance frequencies.     

空化对叶顶间隙泄漏涡演变特性及特征参数影响的大涡模拟研究

利用大涡模拟方法及一个考虑气核效应的欧拉$\!-\!$拉格朗日新空化模型, 对绕NACA0009水翼叶顶间隙泄漏涡(top-leakage vortex, TLV)及其空化流动开展了高精度的模拟, 结果显示数值模拟与实验吻合较好. 在此基础上进一步讨论了不同间隙大小对TLV空化的演变行为及其发生前后TLV强度、气核分布以及切向速度分布等特征参数的变化规律, 分析了TLV空化对TLV演变行为及其特征参数的影响机制. 结果表明, 空化发生后, TLV的强度主要受片空化演变行为的影响, TLV空化对其自身强度的影响较小. 此外, 间隙越小, 片空化越不稳定, TLV的强度也会呈现相应的准周期性波动. 随着间隙的逐渐增大, 片空化强度逐渐减小, 其不稳定性也逐步减弱, TLV强度逐渐恢复至无空化时的水平, 其波动也会逐渐减小. 空化对涡心处气核分布会产生较为明显的影响, 其影响程度取决于空化发生后TLV在空间上的稳定性以及TLV空化的强度. 此外, 空化发生后, TLV半径会在一定程度上增大, 且在空化区域外围形成``类刚体旋转'的切向速度分布特性, 其形成原因主要是空化生长引起的膨胀过程以及流动的黏性作用.      

射流对绕水翼云空化流动抑制机理研究

为理解绕水翼云空化流动的发展机理和探究水翼吸力面开孔射流的影响,采用密度 修正的RNG $k$-$\varepsilon $湍流模型和Schnerr-Sauer空化模型对原始NACA66(mod) 水翼和采用射流后的 水翼的云空化非定常过程进行模拟和对比分析;采用在水翼吸力面近壁区设立监测线的方法对近壁区的流场进行监测,得到 近壁区汽相体积分数、回射流速度、压力及压力梯度的时空分布云图;开展了云空化流场特性的涡动力学分析,进而分析水 翼云空化的发生机理和射流抑制空化的抑制机理. 结果表明:游离型空泡在下游溃灭时产生强烈的局部高压,其向上游传播 导致前缘空穴的一次回缩,而空穴的二次回缩受回射流的影响. 回射流的发展区域受限于较高的压力梯度,高的压力梯度一 直存在,但回射流在一个周期内的首次出现需要时间的积累. 在水翼吸力面射流使得射流孔附近压力升高,弥补了由于空化 和绕流造成的压降,压力梯度增大,抗逆压能力增强,对回射流起到阻挡作用;另一方面,射流使得回射流区域面积和回射 流的强度也有所减小,从而对云空化的发展起到抑制的效果. $Q$准则的涡结构云图相比于汽相体积分数云图能显示复杂的 流动结构,前缘附着型空穴和尾缘游离型空穴内存在旋涡,回射流对空穴存在剪切作用造成空穴脱落. 而射流对空穴和回射 流的剪切和阻挡使云空化发展得到抑制.      

Combined experimental observation and numerical simulation of the cloud cavitation with U-type flow structures on hydrofoils

Sheet/cloud cavitation is an important topic that is a very common type of cavitation in turbo-machinery and marine propeller. Up to now we still have limited understanding of the cavitation shedding dynamics and cloud cavity formation and development. The present study used experimental and numerical studies to gain a better understanding of the complex physics involved in this problem. A series of experimental observations around hydrofoils are carried out in the cavitation tunnel of the China Ship Scientific Research Center (CSSRC) to illustrate the spatial–temporal evolution of the cloud cavity in detail. The results demonstrate that U-type flow structures are common in cloud cavities and can be divided into three stages and the closure line in a sheet cavity often has a convex–concave profile. Reentrant flows occur in the convex region with the jet direction normal to the contour edge so the shedding is mainly caused by the converging reentrant flows. Further analysis demonstrated that there was a striking difference with the cavity growth suppressed substantially in the twisted hydrofoil case if compared with straight hydrofoil and the effect of side entrant jets might make the cavity more uniform across the span. Numerical simulations were used to simulate the formation and development of the cloud cavity. The results show that the strong adverse pressure gradient in the stagnation region at the downstream end of the attached cavity forces the re-entrant flows into the vapor structure with a radially-diverging re-entrant jet and a pair of side-entrant jets, which causes the cavity shedding. Further analyzes of the local flow fields show that the interactions between the circulating flow and the shedding vapor cloud may be the main reason for the formation of the U-type cloud cavity structures.     

Multiscale tow-phase flow modeling of sheet and cloud cavitation

A multiscale two-phase flow model based on a coupled Eulerian/Lagrangian approach is applied to capture the sheet cavitation formation, development, unsteady breakup, and bubble cloud shedding on a hydrofoil. No assumptions are needed on mass transfer. Instead natural free field nuclei and solid boundary nucleation are modelled and enable capture of the sheet and cloud dynamics. The multiscale model includes a micro-scale model for tracking the bubbles, a macro-scale model for describing large cavity dynamics, and a transition scheme to bridge the micro and macro scales. With this multiscale model small nuclei are seen to grow into large bubbles, which eventually merge to form a large scale sheet cavity. A reentrant jet forms under the sheet cavity, travels upstream, and breaks the cavity, resulting in the emission of high pressure peaks as the broken pockets shrink and collapse while travelling downstream. The method is validated on a 2D NACA0015 foil and is shown to be in good agreement with published experimental measurements in terms of sheet cavity lengths and shedding frequencies. Sensitivity assessment of the model parameters and 3D effects on the predicted major cavity dynamics are also discussed.     

收缩扩张管内液氮空化流动演化过程试验研究

本文基于低温空化试验平台研究了收缩扩张流道内液氮非定常空化流动的演化过程. 试验采用高时空分辨率的高速摄像机对77 K液氮在不同空化数σ下空穴结构的演变进行了精细化的分析和研究. 利用试验得到的空穴长度和面积等数据, 定量分析了液氮空化流动的非定常特性与时空演变规律. 研究结果表明: (1)在相似来流速度和温度条件下, 随着空化数的减小, 液氮空化流动呈现四种典型流型, 空穴长度在2.5 h以内为初生空化、空穴长度在2.5 h ~ 7.5 h之间为片状空化、空穴长度在7.5 h ~ 15 h之间为大尺度云状空化, 空穴长度超过15 h为双云状空化, 且在大尺度云状空化和双云状空化阶段均捕捉到了回射流现象; (2)液氮空化流动从初生空化到双云状空化, 脱落空穴的尺度逐渐增大, 空穴面积脉动的幅值和准周期均有所增加. 同时, 在大尺度云状空化与双云状空化阶段, 喉口处堵塞效应对空化流动的影响显著增强; (3)相比于初生空化, 片状空化、大尺度云状空化以及双云状空化中脱落空穴的移动距离依次增加了0.97倍、2.65倍与2.68倍, 溃灭时间依次增加了1.18倍、3.59倍与4.47倍, 但溃灭速度依次减小了0.10倍、0.20倍与0.30倍. 除此之外, 对于双云状空化阶段, 存在两种显著不同的脱落空穴演化过程.      

Multiphase fluid dynamics and transport processes of low capillary number cavitating flows

To better understand the multiphase fluid dynamics and associated transport processes of cavitating flows at the capillary number of 0.74 and 0.54, and to validate the numerical results, a combined computational and experimental investigation of flows around a hydrofoil is studied based on flow visualizations and time-resolved interface movement. The computational model is based on a modified RNG k-ε model as turbulence closure, along with a vapor-liquid mass transfer model for treating the cavitation process. Overall, favorable agreement between the numerical and experimental results is observed. It is shown that the cavi- tation structure depends on the interaction of the water-vapor mixture and the vapor among the whole cavitation stage, the interface between the vapor and the two-phase mixture exhibits substantial unsteadiness. And, the adverse motion of the interface relates to pressure and velocity fluctuations inside the cavity. In particular, the velocity in the vapor region is lower than that in the two-phase region.